PDF Repair and Service Manual E-Z-GO Gasoline Utility Vehicle - 1 MB
This comprehensive repair and service manual covers E-Z-GO gasoline-powered utility vehicles.
It contains detailed instructions for maintenance, troubleshooting, and major repairs for the engine, drivetrain, suspension, and electrical systems.
Whether you're performing routine service or a complete overhaul, this manual is the essential guide for any E-Z-GO technician or owner.
PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
PDF viewer loading area
Text Preview from This Manual
The text below was extracted from the visible preview pages to help you confirm the manual contents before download.
--- Page 1 ---
[I c?4�•1]
TECHNICIAN'S
REPAIR AND SERVICE MANUAL
GASOLINE POWERED UTILITY VEHICLES
STARTING MODEL YEAR: 2000
REVISED: 9/2000
--- Page 3 ---
I GENERAL INFORMATION & ROUTINE MAINTENANCE
TABLE OF CONTENTS FOR SECTION 'A'
SECTION TITLE
I A PAGE NO.
SERIAL NUMBER PLATE LOCATION ............................................................................................A-1
STARTING THE VEHICLE WITH A DISCHARGED BATTERY ...................................................... A-1
FUEL ................................................................................................................................................A-1
SERVICING THE VEHICLE .............................................................................................................A-2
ROUTINE MAINTENANCE ..............................................................................................................A-2
POWERTRAIN MAINTENANCE ......................................................................................................A-2
Checking the Oil Level. ..........................................................................................................A-3
Changing the Oil ....................................................................................................................A-3
AIR CLEANER INSPECTION/REPLACEMENT ..............................................................................A-5
REAR AXLE .....................................................................................................................................A-6
Checking the Lubricant Level ................................................................................................A-6
STARTER/GENERATOR BELT TENSION ......................................................................................A-6
Adjusting the Belt...................................................................................................................A-6
AIR INTAKE AND COOLING FINS ..................................................................................................A-7
SPARK PLUGS ................................................................................................................................A-7
DAILY BRAKE TEST ........................................................................................................................A-8
TIRES ...............................................................................................................................................A-8
CARE AND CLEANING OF THE VEHICLE .....................................................................................A-8
VEH�LE CARE PRODUCTS ..........................................................................................................A-8
TOP AND WINDSHIELD (IF EQUIPPED) ........................................................................................A-9
TRAILERING ....................................................................................................................................A-9
WINTER OR PROLONGED STORAGE ..........................................................................................A-9
HARDWARE ..................................................................................................................................A- 10
TORQUE SPECIFICATIONS ........................................................................................................A- 10
PERIODIC SERVICE SCHEDULE ................................................................................................A- 11
LIST OF ILLUSTRATIONS
Fig. 1 Serial Number Plate Location ................................................................................................A-1
Fig. 2 Fuel Tank ..............................................................................................................................A-1
Fig. 3 Initial Service Chart ...............................................................................................................A-2
Fig. 4 Lubrication Points ..................................................................................................................A-3
Fig. 5 Clean Entire Dipstick .............................................................................................................A-3
Fig. 6 Check Oil Level on Dipstick...................................................................................................A-3
Fig. 7 Oil Viscosity Chart .................................................................................................................A-4
Fig. 8 Cleaning the Top of the Engine .............................................................................................A-4
Fig. 9 Remove Oil Filter...................................................................................................................A-4
Fig. 1 O Cleaning the Oil Filter ..........................................................................................................A-4
Fig. 11 Blowing Out Oil Filter...........................................................................................................A-5
Fig. 12 Adding Engine Oil................................................................................................................A-5
Fig. 13 Air Cleaner ..........................................................................................................................A-5
Fig. 14 Check, Add or Drain Rear Axle Lubricant ...........................................................................A-6
Repair and Service Manual Page A-i
--- Page 4 ---
GENERAL INFORMATION & ROUTINE MAINTENANCE
Read all of Section B and this section before attempting any procedure. Pay particular attention to all Notes, Cautions and Warnings
• Penetrant/Lubricant, a 4-in-1 product that pene TRAILERING
trates the most stubborn of frozen parts, lubricates
leaving a light lubricating film, prevents corrosion Personal injury to occu
by adhering to wet or dry surfaces and displaces AwARNINGA pants of other highway
moisture, sealing against future moisture return. vehicles may occur if
(P/N 75503-G01) vehicle and contents are not adequately secured to
• Multi-purpose Cleaner and Degreaser that con trailer.
tains natural, environmentally safe solvents. (P/N Do not ride on vehicle being trailered.
75504-G01)
• Multi-purpose Hand Cleaner is an industrial Remove windshield and top before trailering. Maxi
strength cleaner containing no harsh solvents, yet mum speed with top is 50 mph (80 kph).
gently lifts grease off hands. May be used with or If the vehicle is to be transported on a trailer at highway
without water. (P/N 75505-G01) speeds, the windshield and top must be removed and the
• Battery Cleaner that promotes easy, non-violent seat bottom secured. Always check that the vehicle and
neutralization of battery acids and battery acid contents are adequately secured before trailering the
crystals. The resulting sodium salts are water sol vehicle. The rated capacity of the trailer must exceed the
uble and easily washed away. (P/N 75506-G01) weight of the vehicle (see GENERAL SPECIFICATIONS
• Biodegradable Cleaner that cleans the toughest for vehicle weight). Lock the parking brake and secure
dirt and heavy soils by breaking down grease to the vehicle to the trailer using ratchet tie downs.
be easily wiped or rinsed away. (P/N 75507-G01)
• Multi-purpose Value Pack sampler package
including 4 ounce (118 ml) aerosol cans of Battery WINTER OR PROLONGED STORAGE
Protector, Penetrant/Lubricant, White Lithium
Keep hands, clothing
Grease, and Carburetor and Choke Cleaner. (P/N AwARNINGA and jewelry away from
75508-G01)
moving parts. Use care
• Plexus plastic cleaner and polish removes minor not to contact hot objects. Raise the rear of the vehi
scratches from windshield. (P/N 28433-G**) cle and support on jack stands before attempting to
run the engine.
TOP AND WINDSHIELD (IF EQUIPPED) Preparing the engine for winter or a prolonged storage
The top does not provide calls for a few simple steps to prevent a build up of var
AwARNINGA protection from roll over nish and gum in the carburetor and corrosion in the
or falling objects. engine.
The windshield does not provide protection from tree Raise the rear of the vehicle and support on jack stands.
limbs or flying objects. Add fuel stabilizer to the tank in accordance with the
manufacturer's recommendations. Disconnect the fuel
Clean with lots of water and a clean cloth. Minor line from the engine at the fuel tank. With proper ventila
scratches may be removed using a commercial plastic tion, start the engine and allow to run until the engine
polish or E-Z-GO Plexus plastic cleaner (P/N 28433- stops due to lack of fuel. Drain carburetor bowl using the
G**). drain screw and re-tighten. Remove the air filter and
spray a commercial fogging or cylinder oil into the carbu
retor while operating the starter for 2 - 3 seconds. Rein
stall the air filter and attach the fuel line to the tank.
I I
NOTE The vehicle can be stored for the winter with
�- ---�- the old oil left in the engine. The oil should be
changed as part of spring maintenance. This will remove any
moisture that has accumulated during storage.
Repair and Service Manual Page A-9
--- Page 5 ---
SAFETY
Read all of Section A and this section before attempting any procedure. Pay particular attention to all Notes, Cautions and Warnings
NOTES, CAUTIONS AND WARNINGS vehicle unstable or prone to roll over and could result
in injury or death to the operator or passenger.
Throughout this manual, the following NOTES, CAU
TIONS and WARNINGS are used. For the protection of
all personnel and the vehicle, be aware of and observe GENERAL MAINTENANCE
the following: When any maintenance procedure or inspection is per
I I
NOTE A NOTE indicates a condition that should be
�- ---�- observed.
formed, it is important that care be exercised to insure
the safety of the technician/mechanic or bystanders and
to prevent damage to the vehicle.
CAUTION A CAUTION indicates a condition that
may result in damage to the vehicle or Always read and understand the entire relevant manual
surrounding facilities. section (chapter) before attempting any inspection or
service.
A WARNING indicates a
AwARNINGA hazardous c o n d i t i o n
which could result in BEFORE SERVICING THE VEHICLE
serious injury or death. Before attempting to inspect or service a vehicle, be sure
to read and understand the following warnings:
IMPORTANT SAFETY WARNING Before working on vehi
In any product, components will eventually fail to perform AwARNINGA cle, remove all jewelry
properly as the result of normal use, age, wear or abuse. (watch, rings, necklaces,
etc.).
It is virtually impossible to anticipate all possible compo
nent failures or the manner in which each component Be sure that no loose clothing or hair can contact
may fail. moving parts.
Be aware that a vehicle requiring repair indicates that the Use care not to contact hot objects.
vehicle is no longer functioning as designed and there Before attempting to operate or adjust the powertrain,
fore should be considered potentially hazardous. Use the rear of the vehicle must be raised and supported
extreme care when working on any vehicle. When diag on jack stands.
nosing, removing or replacing any components that are
not operating correctly, take the time to consider the Wear OSHA approved clothing and eye protection
safety of yourself and others around you if the compo when working on anything that could expose the
nent should move unexpectedly. body or eyes to potential injury. In particular, use care
when working with or around batteries, compressed
Some components are heavy, spring loaded, highly cor
air or solvents.
rosive, explosive or may produce high amperage or
reach high temperatures. Gasoline, carbon monoxide, Always turn the key switch to 'OFF' and remove the
battery acid and hydrogen gas could result in serious key before disconnecting a live circuit.
bodily injury to the technician/mechanic and bystanders if When connecting battery cables, pay particular atten
not treated with utmost caution. Be careful not to place tion to the polarity of the battery terminals. Never con
hands, face, feet or body in a location that could expose fuse the positive and negative cables.
them to injury should an unforeseen situation occur.
Set the parking brake before performing any work on
Always use the appropriate tools listed in the tool list and the vehicle.
wear approved safety equipment.
Keep all smoking materials, open flame or sparks
MODIFICATIONS TO VEHICLE away from gasoline or batteries.
Do not modify the vehicle in any manner that will change If repairs are to be made that will require welding or
the weight distribution of the vehicle. cutting, the battery and fuel tank must be removed
Changes to the weight and the fuel system drained.
AwARNINGA distribution or the center Never operate the starter with the spark plugs
of gravity may make the removed unless the ignition system has been dis-
Repair and Service Manual Page B-5
--- Page 6 ---
BODY AND TRUCKBEDS
Read all of Section B and this section before attempting any procedure. Pay particular attention to all Notes, Cautions and Warnings
Fig. 5 Truckbed Components ST 350
Repair and Service Manual Page C-5
--- Page 7 ---
FRONT SUSPENSION AND STEERING
Read all of Section Band this section before attempting any procedure. Pay particular attention to all Notes, Cautions and Warnings
FRONT SUSPENSION Front Axle Replacement
E
I NOTE I removing/installing
In the following text, there are references to
bolts etc. Additional hard
Tool List Qty. Required
Wheel chocks .............................................................. 4
ware (nuts, washers etc.) that are removed must always be Floor jack ..................................................................... 1
installed in their original positions unless otherwise specified.
Jack stands ................................................................. 2
Non-specified torque specifications are as shown in the table
contained in Section A. Impact wrench, 1/2" drive ............................................ 1
Impact socket, 3/4", 1/2" drive ..................................... 1
To reduce the possibility
AwARNINGA of personal injury, follow Pliers ........................................................................... 1
the lifting procedure in Wrench, 3/4" ................................................................ 1
Section B of this manual. Place wheel chocks in front Plastic faced hammer .................................................. 1
and behind the rear wheels. Check the stability of the Socket, 9/16", 1/2" drive .............................................. 1
vehicle on the jack stands before starting any repair Wrench, 9/16" .............................................................. 1
procedure. Never work on a vehicle that is supported Torque wrench, 1/2" drive, ft. lbs. ................................ 1
by a jack alone.
Lift and support front of vehicle per SAFETY section.
Front Shock Absorber Replacement
Remove the front wheels. Remove the bottom shock
Tool List Qty. Required absorber mounting hardware (Ref Fig. 1 on page E-2).
Wrench, 9/16" ............................................................. 1 Remove the cotter pin (7) from the king pin (8). Loosen
Remove the nut (4) from the bottom of the shock the nut (9) until the threaded end of king pin is protected.
absorber (1) at the front axle (2) (Ref Fig. 1 on page E-2). Tap the nut with a plastic faced hammer to loosen the
Compress the shock absorber to clear the mounting king pin.
bracket. Remove the nut (9) and washer (23) from the king pin.
Loosen the nut (4) securing the top of the shock absorber Remove the king pin (8), washer (21), thrust washer (10)
to the vehicle frame and then rotate the shock absorber and spindle sleeve (22) from the spindle and swing it to
while holding the nut in place with a wrench. the side. Remove the hardware (12) that secures the
Remove the shock absorber. front of the leaf spring to the front axle.
The installation of the shock absorber is the reverse of Front axle installation is in the reverse order of disassem
disassembly, except that the mounting nuts should be bly.
I�- NOTE
---�-I die bushing.
tightened until the rubber bushings (5) expand to the The thru�t washer is located on top of the spin
diameter of the shock absorber washers (6).
Shock Boot Removal and Replacement Tighten the king pin nut (9) to 40 - 50 ft. lbs. (55 - 70 Nm)
Tool List Qty. Required torque.
Wrench, 9/16" ............................................................. 1 Replace the king pin cotter pins with new ones.
Remove the nut (4) from the bottom of the shock
absorber (1) at the front axle (2) (Ref Fig. 1 on page E-2). I-
�- �I - aligned with the frame. This is not a wheel
NOTE
- -
After replacing the front axle, the axle must be
Compress the shock absorber to clear the mounting alignment. Replacing the axle will also require that the front
bracket. wheels be aligned.
Remove clamps securing the boot to the shock absorber When the front axle is replaced, it must be aligned to the
and slide boot down and off the shock absorber. frame. The distance from the center bolt at rear of left
spring to the center bolt at front of right spring must be
Replace shock boot and reattach shock absorber as the same as the distance from the center bolt at rear of
instructed above. right spring to the center bolt at front of left spring (Ref
Fig. 2 on page E-2).
Tighten leaf spring hardware (12) to 35 - 50 ft. lbs (50 -
70 Nm) torque.
Repair and Service Manual Page E-1
--- Page 8 ---
ELECTRICAL
TABLE OF CONTENTS FOR SECTION 'F'
SECTION TITLE
F PAGE NO.
CIRCUITS AND CONTROLS........................................................................................................... F-1
STARTER......................................................................................................................................... F-1
GENERATOR................................................................................................................................... F-1
WIRING ............................................................................................................................................ F-1
TESTING IGNITION CIRCUIT ......................................................................................................... F-1
Testing the Ignition Coil ......................................................................................................... F- 4
Testing the Pulser Coil .......................................................................................................... F- 4
TESTING STARTING CIRCUIT ....................................................................................................... F- 5
TESTING CHARGING CIRCUIT...................................................................................................... F- 6
STARTER/GENERATOR ................................................................................................................. F- 6
Starter/Generator Removal ................................................................................................... F- 6
Starter/Generator Disassembly ............................................................................................. F- 6
Starter/Generator Inspection ................................................................................................. F- 8
Starter/Generator Repair and Replacement .......................................................................... F- 8
BATTERY VOLTAGE TEST............................................................................................................. F- 8
STORAGE OF BATTERY ................................................................................................................ F- 8
LIST OF ILLUSTRATIONS
Fig. 1 Electrical System Wiring Diagram ......................................................................................... F- 2
Fig. 2 Electrical System (Physical Location) ................................................................................... F- 3
Fig. 3 Ignition Coil Check Method ................................................................................................... F- 4
Fig. 4 Normal Circuit........................................................................................................................ F- 5
Fig. 5 Starter/Generator .................................................................................................................. F- 7
Fig. 6 Starter/Generator Brush Removal ......................................................................................... F- 7
Fig. 7 Bearing Removal ................................................................................................................... F- 7
Repair and Service Manual Page F-i
--- Page 9 ---
ACCESSORY WIRING
TABLE OF CONTENTS FOR SECTION 'G'
SECTION TITLE PAGE NO.
DIGITAL VOLT OHM METER ......................................................................................................... G - 1
TROUBLESHOOTING .................................................................................................................... G - 1
POWER SUPPLY............................................................................................................................ G - 3
ACCESSORY WIRING ................................................................................................................... G - 3
LIST OF ILLUSTRATIONS
Fig. 1 DVOM................................................................................................................................... G - 1
Fig. 2 Wiring Diagram ..................................................................................................................... G - 2
Repair and Service Manual Page G-i
--- Page 11 ---
ENGINE
Read all of Section B and this section before attempting any procedure. Pay particular attention to all Notes, Cautions and Warnings
Intake (>
-- ---- ---- ---- ---- ---- ---- ---- ---- --
- - - - - - - - - - - -- -- -- -
--- ---- ---- ---- ---- ---- ---- ---- ---- --
INTAKE
0
COMPRESSION
First Revolution
0
0
POWER EXHAUST
Second Revolution
NOTE: This is a simplified diagram for explanatory use only.
Rockers, guides, seals, etc. have been omitted.
Fig. 2 Four Cycle Operation
Repair and Service Manual Page H-3
--- Page 12 ---
FUEL SYSTEM
TABLE OF CONTENTS FOR SECTION 'J'
SECTION TITLE
J
PAGE NO.
GENERAL ........................................................................................................................................ J-1
CARBURETOR OPERATION .......................................................................................................... J-1
Float System.......................................................................................................................... J-1
Pilot Jet System ..................................................................................................................... J-1