PDF Operator’s Manual Manitou MT 835 H MT 1135 H MT 1335 H Forklift - 3 MB
This operator's manual covers the Manitou MT 835 H, MT 1135 H, and MT 1335 H ST3B series of forklift trucks.
It is an essential guide for safe and efficient operation, detailing all controls, instruments, and recommended procedures.
Operators can learn about the machine's capabilities and limitations, ensuring proper handling of loads.
This manual is a critical tool for safety and performance on any job site.
PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
PDF viewer loading area
Text Preview from This Manual
The text below was extracted from the visible preview pages to help you confirm the manual contents before download.
--- Page 1 ---
647105 EN (12/06/2018)
MT 835 H ST3B
MT 1135 H ST3B
MT 1335 H ST3B
OPERATOR'S MANUAL
(ORIGINAL INSTRUCTIONS)
--- Page 3 ---
• Adapt the seat adjustment to the operator's weight (according to lift truck model) and maintain it in good condition,
as well as the cab suspension. Inflate the tires in accordance with recommendations.
• Ensure that the operators adapt their operating speed to suit the conditions on site.
• As far as possible, arrange the site in such a way as to provide a flat running surface and remove obstacles and harmful
potholes.
C - MODIFICATION OF THE LIFT TRUCK
- For your safety and that of others, you must not change the structure and settings of the various components used in your
lift truck (hydraulic pressure, calibrating limiters, engine speed, addition of extra equipment, addition of counterweight,
unapproved attachments, alarm systems, etc.) yourself. In this event, the manufacturer cannot be held responsible.
D - FRENCH ROAD TRAFFIC RULES
(or see current legislation in other countries)
- Only one certificate of conformity is issued. It must be kept in a safe place.
- The driving of non EC type-approved tractors on the public highway is subject to the provisions of the highway code
relating to special machines, defined in article R311-1 of the highway code, in category B of the Equipment Order of
20 November 1969 that determines the procedures applicable to special machines. The lift truck must be fitted with a
licence plate.
- The driving of EC type-approved tractors on the public highway is subject to the provisions of the highway code regarding
agricultural tractors, defined in article R311-1 of the highway code. The lift truck must be registered.
SPECIAL INSTRUCTION APPLYING TO "EC TRACTOR" TYPE-APPROVED LIFT TRUCKS
- All EC tractor type-approved lift trucks are supplied with an "EC tractor" certificate complying with directive 2003/37/EC, to be retained by the owner, and a page of
administrative details together with a CNIT number (national type approval code) for registration at the prefecture.
- The lift truck owner is responsible for carrying out the necessary procedures for obtaining the vehicle registration document within the time limit defined by the regulations.
- The operator must hold an HGV licence, unless granted an exemption.
- The lift truck must be driven on the public highway in accordance with the instructions given in the manual supplied with the lift truck (Gross weight, Gross combination
weight, towing load, axle loads, maximum speeds, etc. according to type/version). The operator must be in possession of the lift truck’s registration document.
IMPORTANT
When towing a trailer or agricultural equipment, the travelling speed of the lift truck is limited to 25 km/h.
In this case, a "25" disc must be affixed to the rear of the convoy.
E - LIFT TRUCK CAB PROTECTION
- All lift trucks comply with the requirements of ISO 3471 (wheel loader code) regarding cab rollover protection (ROPS)
and ISO 3449 (Level II) regarding the protection of the cab against falling objects (FOPS).
- "EC TRACTOR" type-approved lift trucks comply, in addition, with Directive 79/622/EC (OECD Code 4) regarding cab
rollover protection (ROPS).
IMPORTANT
Structural damage or overturning, a modification, changes or a poorly executed repair can reduce the protective efficiency of the cab, cancelling its compliance.
Do not perform welding or drilling on the cab structure.
Consult your dealer to determine the limits of this structure without cancelling its compliance.
THE INSTRUCTIONS
- The operator's manual must always be in good condition and kept in the place provided on the lift truck and in the
language used by the operator.
- The operator's manual and any plates or stickers which are no longer legible or are damaged, must be replaced immediately.
THE MAINTENANCE
- Maintenance or repairs other than those detailed in part: 3 - MAINTENANCE must be carried out by qualified personnel
(consult your dealer) and under the necessary safety conditions to maintain the health of the operator and any third party.
IMPORTANT
Your lift truck must be inspected periodically to ensure that it remains in compliance.
The frequency of this inspection is defined by current legislation in the country in which the lift truck is used.
- Example for France "The manager in charge of the establishment using a lift truck must open and maintain a maintenance
MT 835 / 1135 / 1335 H ST3B
log for each machine (order of 2 March 2004) and undergo a general periodic inspection every 6 months (order of 1
March 2004)".
647105 (12/06/2018)
1-7
--- Page 4 ---
LAYING A HIGH LOAD ON TYRES F6
- Approach the load in the transport position in front of the stack (fig. F6).
- Apply the parking brake and place the forward/reverse selector in neutral.
- Raise and extend the jib (1) (2) until the load is above the stack, while monitoring
the longitudinal stability limiter and warning device (see: INSTRUCTIONS FOR
HANDLING A LOAD: C - LONGITUDINAL STABILITY LIMITER AND WARNING DEVICE).
If necessary, move the lift truck (3) forward (fig. F7), driving very slowly and carefully.
- Place the load in a horizontal position and lay it down on the pile by lowering and
retracting the jib (1) (2) in order to position the load correctly (fig. F8).
- If possible, release the fork by alternately retracting and raising the jib (1) (fig. F9).
Then set the forks into transport position.
- If this is not possible, reverse the lift truck (1) very slowly and carefully to release
the forks (fig. F10). Then set them into transport position.
F7
2
1
3
F8
1
2
F9
1
F10
MT 835 / 1135 / 1335 H ST3B
647105 (12/06/2018)
1
1 - 17
--- Page 5 ---
LIFT TRUCK DISPOSAL
MANITOU complies with the regulations deriving from Directive 2000/53/EC relating to lift truck end-of-life.
This lift truck contains no substances or materials forbidden by Directive 2000/53/EC.
NOTE: Consult your dealer before disposing of your lift truck.
RECYCLING OF MATERIALS
METALS
• Metals are 100 % recoverable and recyclable.
PLASTICS
• Plastic parts are identified with a marking in accordance with current regulations.
• A limited range of materials is used to simplify the recycling process.
• The majority of plastic components are made of "thermoplastic" plastics, that are easily recycled by melting, granulating
or grinding.
RUBBER
• Tyres and seals can be ground for use in cement manufacture or to obtain reusable granules.
GLASS
• Glass items can be removed and collected for processing by glaziers.
ENVIRONMENTAL PROTECTION
By entrusting the maintenance of your lift truck to the MANITOU network, the risk of pollution is limited and the contribution
to environmental protection contribution is made.
WORN OR DAMAGED PARTS
• Do not dump them in the countryside.
• MANITOU and its network have signed-up to a scheme of environmental protection through recycling.
USED OIL
• The MANITOU network organises the collection and processing of used oil products.
• By handing over your waste oil to MANITOU, the risk of pollution is limited.
USED BATTERIES
• Do not throw away batteries, as they contain metals that are harmful for the environment.
• Return them to the MANITOU network or any other approved collection point.
NOTE: MANITOU aims to manufacture lift trucks that provide the best performance and limit polluting emissions.
MT 835 / 1135 / 1335 H ST3B
647105 (12/06/2018)
1 - 27
--- Page 6 ---
N°310988 N°310973 N°308754
50° 60° 68° 50° 60° 68° 50° 60° 71°
8 D
7.75 14
40°
7 C 11 E 13
40° 12.30
10.75 E
B 40° 12
3000 KG
10 D
6 11 D
A
9
30° C 10
5 C
8
B 9
30° 30° B
4 7 8
A
3500 KG
A
2500 KG
20° 6 7 KG
2000 KG
00
3 30
1500 KG
6 KG
3500KG
5 00
2500KG
20° 35
3000KG
20°
1000 KG
2000KG
2 5
1600KG
4
1200KG
1500KG
2000KG
2500KG
10°
1200KG
1150KG
4
600 KG
1000KG
3
800KG
1 3
600KG
10°
MT1135H 10°
400 KG
2
400KG
0° 2
0m
300KG
-3° D C B A 0.5m 1 1
5 4 3 2 1 0m
MT835 H 0° 0 0° 0 MT 1335 H
-3° 0.5m
-3°
-1 -1
4.25 2.95 1.95 1.50 8 7 6 5 4 3 2 1 0m 10 9 8 7 6 5 4 3 2 1 0m
4.45 3.70 2.45 1.70 8.75 7.30 5.60 4.25 3.05 1.85
6.85 5.35 4.15 2.80 2.05
7.75 3.35 2.35 8.25 6.35 5.10 3.65 2.25
2.55
SUIVANT NORME EN 1459 annexe B. SUIVANT NORME EN 1459 annexe B. SUIVANT NORME EN 1459 annexe B.
17 18 19