PDF Circuit Diagram Manual Tadano Faun AR 1000M-1 All Terrain Crane - 3 MB
Troubleshoot complex electrical and hydraulic issues with the detailed circuit diagram manual for the Tadano Faun AR 1000M-1 All Terrain Crane.
This specialized manual is essential for technicians, providing complete schematics for all the crane's systems.
It allows for efficient fault finding and repair, ensuring your crane operates safely and reliably.
Without these diagrams, diagnosing electrical problems can be nearly impossible.
PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
PDF viewer loading area
Text Preview from This Manual
The text below was extracted from the visible preview pages to help you confirm the manual contents before download.
--- Page 1 ---
Publication No. AR-1000M-1/C2-1E
01
All Terrain Crane
AR-1000M-1
Model
Applicable Serial No. GA5002 -
--- Page 3 ---
Y- 3 . Y- 3 .
Adjustment (pressure)
5. Relief valve
(for jib extension circuit pressure reduction, PR11)
A f t e r f u l l y r et r a c t i n g t h e c o u nt e r we i g ht m o u nt i n g /
dismounting cylinder, shift the counter weight cylinder
telescoping switch to “raising” side to adjust the pressure.
Pump speed: MAX (2000 rpm)
Shift the boom/jib selector switch to the “jib tilt” position. 7. Relief valve (RV7 for counterweight rotator circuit)
Fully extend the jib telescoping cylinder.
Move the jib operation lever to the jib extending side to
check the pressure value shown on the multi-display.
Pump speed: MAX (2000 rpm)
6. Remote control valve (main relief valve, RV5(C))
G port
Install the pressure gauge to the G port of the remote
control valve.
Fully extend the counter weight mounting/dismounting
cylinder.
Shift the counterweight lock/release switch to the lock side
and measure the pressure after the counterweight lock pin
(counterweight mounting/dismounting cylinder rod section)
has moved to the lock position.
Pump speed: IDL (600 rpm)
Install the pressure gauge to the G port of the remote
control valve.
Shift the crane mounting/dismounting switch to “working”
side.
Shift the RC computer selector switch of the remote control
device to the “manual” side.
Y03-1090E
--- Page 4 ---
System Diagrams
Contents
Z-1 Hydraulic Circuit (Upper)............ 1
Z-3 Electric Circuit (Upper)................ 5
Z-4 Electric Circuit
(Crane electrical equipment).... 10
Z-5 Electric Circuit
(Electric circuit for mounting/
dismounting revolving
superstructure,counterweight)...... 11
Z-6 Electric Circuit
(Engine electric circuit)............. 14
Z-7 Electric Circuit (Lower)............. 15
Z-8 Electric Circuit
(Air conditioner)......................... 17
Z-9 Electric Circuit
(Upper wiring 1 (cab))................ 19
Z-10 Electric Circuit
(Upper wiring 2 (swing table))..... 25
Z-11 Electric Circuit
(Engine wiring)........................... 27
Z
--- Page 5 ---
Z-4 Z-4
Electric Circuit
Crane electrical equipment circuit
Water
temperature
gauge Temperature sender unit
Fuel
gauge Fuel sender unit
Horn
Power supply for Horn switch
mounting/dismounting
(Swing lever)
NISSAN carrier only
power supply [radio]
illumination Speaker (left)
illumination
power supply
Speaker (right
Fuse box Upper electric circuit
to CN 2 - 49, 50
to CN 1 - 35 AML
to CN 2 - 59, 60 controller
to accessory circuit
AML power supply, solenoid
Cigar lighter
to panel lamp
from main fuse
to blower motor,
from starter switch to control amplifier etc.
AC terminal
Panel switch
Boom lamp
from battery
Working lamp
Working lamp SW Winch drum illumination lamp
Front lamp Rear lamp
Wiper motor Wiper motor
Intermittent Intermittent Washer motor
wiper relay wiper relay
Rotary joint
Front Roof
To carrier light SW
Window washer
Front wiper switch Roof wiper switch
Opened door detector SW
(Contact broken for door left open)
Room lamp
10 Z03-6530E
10
--- Page 6 ---
Z-9 Z-9 Z-9
Electric Circuit
Upper wiring (cab)
Water temperature
Boom telescoping
Swing brake state Boom sequential Jib removed indicator lamp
Cab tilt state indicator lamp Crane dismount indicator lamp
AML abnormality Accumulator low-pressure Swing automatic stop Counter weight improper setup C/W lock indicator lamp Swing lock indicator lamp indicator lamp telescoping indicator lamp Jib tilt operation indicator lamp Warning for air filter choking Warning for charging
Fuel gauge
indicator lamp warning cancel indicator lamp warning lamp
indicator lamp
Jib tilt
gauge
indicator lamp
Jib telescoping indicator lamp
C/W lock release Boom synchronized
C/W cylinder full extension telescoping indicator lamp Eng. warning for oir filter Eng.
Elevation slow stop indicator lamp warning for oir pressure choking
cancel indicator lamp indicator lamp choking
Hook amount of movement Winch/jib, telescoping/elevation Starter SW
Boom telescoping mode C/W CYL telescoping
Hook amount of movement main / aux. selection Swing lock pin release SW Swing brake release SW Swing free/lock selection high speed selector SW selector SW operation SW C/W free/lock operation SW Crane dismounting SW Working lamp SW
Window washer SW Roof wiper SW
indication reset
Front wiper SW
Capacitor for preventing
front wiper motor noise
Capacitor for preventing
roof wiper motor noise
Capacitor for preventing
window washer motor noise
Elevation slow stop cancel input
Phase A input by proximity switch (main) Signal
Phase B input by proximity switch (main)
Phase A input by proximity switch (aux.) transmitter Constant current amplifier
Phase B input by proximity switch (aux.) Wiper relay (for swing,
External reset input (front) elevation stop) Swing
Swing Swing
Elevation
Elevation Elevation
front roof
Shield Y
Back lamp
Window washer tank
Main/aux. selection input
Hook amount of movement indicator Shield Y Wiper relay
(roof)