PDF Workshop Service Repair Manual Ferrari 360 Gearbox Transmission - 2 MB

This specialist workshop manual focuses exclusively on the gearbox and transmission of the Ferrari 360.

It provides detailed, step-by-step procedures for the service, repair, and overhaul of this complex component.

With technical specifications, torque settings, and special tool requirements, this manual is essential for any technician working on a Ferrari 360 transmission.

Ensure your repairs are performed to factory standards.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram βœ‰Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
0 GENERAL INFORMATION

C6.02 ENGINE PARAMETERS DISPLAY
C6.03 ERROR SIGNALS
C6.04 ACTIVE DIAGNOSIS
C6.05 AUTOMATIC CYCLE
D CLUTCH-GEARBOX-DIFFERENTIAL
D1 GENERAL SPECIFICATIONS
D1.01 TECHNICAL FEATURES
D1.02 SPECIFIC TOOLING
D1.03 COMMERCIAL TOOLING
D1.04 TIGHTENING TORQUES
D2 DETACHING THE ENTIRE GEARBOX- DIFFERENTIAL UNIT
D2.01 DISMANTLING
D2.02 RE-ASSEMBLY
D3 CLUTCH
D3.01 REPLACING THE COMPONENTS
D3.02 CLUTCH PEDAL STROKE ADJUSTMENT
D3.03 CLUTCH CONTROL HYDRAULIC SYSTEM
D3.04 SYSTEM BLEEDING
D4 GEARBOX
D4.01 REPLACING THE EXTERNAL COMPONENTS
D4.02 REPLACING AND ADJUSTING THE CONTROL CABLES
D4.03 REPLACING THE GEARBOX LEVER HOUSING
D4.04 DETACHING/RE-FITTING THE GEARBOX SUPPORT MOVABLE FRAME
D4.05 GEARBOX OVERHAUL
D5 DIFFERENTIAL- AXLE SHAFTS
D5.01 REPLACING THE COMPONENTS
D5.02 AXLE SHAFT
D6 ELECTRONICALLY-CONTROLLED GEARBOX
D6.01 INTRODUCTION
D6.02 GENERAL FEATURES
D6.03 TRANSMISSION CONTROL UNIT (TCU)
D6.04 OPERATION
D6.05 HYDRAULIC SYSTEM
D6.06 POWER UNIT
D6.07 ACTUATORS
D6.08 MEASURING SENSORS AND SIGNAL SWITCHES
D6.09 SIGNALS AND CONTROLS
D6.10 SYSTEM FUNCTIONS
D6.11 REPLACING THE ELECTRONIC CONTROL UNIT (TCU)


file:///C|/Documents%20and%20Settings/Owner/M.../360%20SPIDER%20WSM/0_general_information.htm (5 of 12) [3/7/2006 11:49:50 PM]

--- Page 3 ---
http://127.0.0.1:8500/F131_S_E/dt/mo/d/d2_01.htm


                D2.01               DISMANTLING


   This paragraph describes the dismantling procedure of the entire gearbox-differential
   unit from the car. This procedure is necessary in case of overhaul or complete
   replacement of the gearbox or in case of repair work that cannot be carried out with
   the gearbox installed in the car.

   NOTES
   The procedure and the figures refer to the disassembly of a electronically controlled
   gearbox. The disassembly procedure for a mechanically controlled gearbox is similar,
   for this reason only the differences are illustrated.

   Procedures

   The gearbox-differential unit must be lifted from the engine compartment. To carry out
   this procedure it is necessary to use a movable hydraulic hoist or a bridge crane with
   200 kg minimum capacity and two safety belts to sling the unit.

   IMPORTANT
   Before starting procedures within the engine compartment, adequately protect all the
   polished surfaces of the car body and chassis.

   β€’     Drain the engine oil (                    A 3.01).
   β€’     Remove:
        - the engine compartment boot (                              M 2.01);
        - the side protection guards of the engine compartment (                    M 2.13);
   - the complete soft top unit (                         N 2.01);

    IMPORTANT
    FROM the vehicle Ass. No. 41464, the gearbox-differential unit can be removed
    without having to lift the top unit. This is possible because the new top housing bays
    are equipped with openings which provide access to the fastening screws of the side
    frame supporting the gearbox. Such screws can therefore be removed without lifting
    the top.


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d2_01.htm (1 of 13) [3/7/2006 11:57:08 PM]

--- Page 4 ---
http://127.0.0.1:8500/F131_S_E/dt/mo/d/d2_01.htm


   β€’ In the lower part of the engine, unscrew the screws (10) fastening the lower part of
   the gearbox to the engine.


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d2_01.htm (11 of 13) [3/7/2006 11:57:08 PM]

--- Page 5 ---
http://127.0.0.1:8500/F131_S_E/dt/mo/d/d2_02.htm


   β€’ Re-assemble the oil coolant pipes onto the gearbox, re-utilizing the original
   gaskets and locking the unions (8) to the prescribed torque.


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d2_02.htm (8 of 12) [3/7/2006 11:57:12 PM]

--- Page 6 ---
http://127.0.0.1:8500/F131_S_E/dt/mo/d/d3_01.htm

 β€’ Unscrew and remove the eight screws fastening the flywheel to the crankshaft.
 β€’ Remove the washer (3) and the flywheel together with the toothed wheel.
 β€’ Detach the toothed wheel from the flywheel.
 Check the work surface of the clutch disk on the flywheel. No grooves or deformations should appear.
 Check the flatness of the surface.
 If the flywheel requires grinding, stick to the prescribed values (     D 1.01).
 β€’ During re-assembly, the flywheel and the washer (3) may be mounted in a single position since the
 screw (4), positioned with the yellow mark on the flywheel, is offset with respect to the others.

  IMPORTANT
  Always use new screws and washers every time the unit is refitted.

 β€’ Lock the engine rotation and tighten the flywheel screws to the prescribed torque.

  Thrust bearing unit parts for clutch and pipes

  β€’ Unscrew the two screws (5) fastening the guide support (6) and remove the latter from the flange.
  To prevent problems during the clutch position resetting stage, FROM Ass.ly No. 50345 a guide
  mount (6) has been introduced. This has a longer housing slot for the anti-rotation pin (increased from
  27.8 to 33 mm).


  Notes for "F1" gearbox
  In "F1" gearboxes the bracket (6) supports the clutch position sensor (      D 6.08).
  The bearing guide function is made of two stud bolts (16) which also contribute to fastening the
  bearing holder flange.
  To prevent problems during the clutch position resetting stage, FROM Ass.ly No. 53232 a stud bolt
  (16) with a longer shaft has been introduced.


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d3_01.htm (6 of 14) [3/7/2006 11:57:15 PM]

--- Page 7 ---
http://127.0.0.1:8500/F131_S_E/dt/mo/d/d3_02.htm


   to adjust the pedal into the resting position, in order to align it with the brake pedal.
   Proceed as described.
   β€’ Loosen the lock-nut (2) and unscrew the adjusting screw (1).


   β€’ Loosen the lock-nut (B) and turn the pump adjusting screw (A) until the pedal is
   properly positioned.


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d3_02.htm (2 of 6) [3/7/2006 11:57:17 PM]

--- Page 8 ---
http://127.0.0.1:8500/F131_S_E/dt/mo/d/d3_04.htm


   β€’ Press the clutch pedal and simultaneously unscrew the bleeding union; carry out
   the necessary number of cycles until only fluid comes out of the pipe, without air
   bubbles.
   β€’ Tighten the bleeding union to the prescribed torque and re-assemble the protection
   plug.
   β€’ Fill-up the fluid in the tank to the "MAX" level.
   β€’ Re-assemble the parts removed during the procedure.


   Electronically Controlled gerabox

   Clutch Draining

   In the system, as well as the union (1) on the gearbox (see mechanical gearbox),
   there is also a second union (2) on the block for the clutch pipe rapid coupling, located
   in position with the right-hand rear fastening point of the gearbox support frame.


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d3_04.htm (2 of 5) [3/7/2006 11:57:20 PM]

--- Page 9 ---
#$


     β€’ Position the grommet with its closed side facing outwards and, reusing the AV
     3218 punch, bring it flush with the cover.


     β€’ Grease the flange pin with gearbox oil, then mount the differential cover (A) onto
     the flange shaft
     β€’ Rest the inner ring of the differential lid's (A) bearing on the base of the (a) AV


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d4_01.htm (7 of 21) [3/7/2006 11:57:24 PM]

--- Page 10 ---
#$

     Gearshift selection levers (Mechanically controlled gearbox)

     In case of excessive end float of the gear-shift selection levers on the respective
     pivots, it is possible to replace the levers which are supplied as spare parts complete
     with roller bearings.
     β€’ To gain access to the levers it is necessary to remove the rear part of the
     underfloor (     M2.12).
     β€’ Remove the joints of the control cables from the levers, unscrewing the nuts (8) on
     the fulcrum screws.


     β€’ Remove the seeger ring on the pivots (9) and remove the connecting rods from the
     gear-shift selection and engagement levers.
     β€’ Unscrew the screw (10) and slide off the lever with all the support parts.


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d4_01.htm (17 of 21) [3/7/2006 11:57:24 PM]

--- Page 11 ---
http://127.0.0.1:8500/F131_S_E/dt/mo/d/d4_02.htm


   β€’ Working from under the car, make sure that the cable hitch (5) is correctly
   positioned on the chassis and lay the cables next to the propeller, avoiding
   intertwining.


   β€’ Connect the cable joints to the levers on the right-hand side of the gearbox,
   making sure that the cable with the protection (B, light blue) is connected to the
   lower selection lever.

http://127.0.0.1:8500/F131_S_E/dt/mo/d/d4_02.htm (6 of 10) [3/7/2006 11:57:26 PM]

--- Page 12 ---
http://127.0.0.1:8500/F131_S_E/dt/mo/d/d4_04.htm


                    D4.04 DETACHING/RE-FITTING THE GEARBOX SUPPORT
                    MOVABLE FRAME


      Tightening torques

      Screws for fastening frame to chassis         28,5 Nm
      Screws for fastening frame to gearbox          98 Nm
      Screw fastening the cross member to the frame 9,8 Nm

       Detaching the frame

       β€’ Remove the rear part of the underfloor (                                   M 2.12);
       β€’ Remove the engine compartment side guards (                                       M 2.13);
       β€’ Remove the coolant expansion tank (                                    B 5.05) leaving it connected to the
       system.
       β€’ Remove the air intake way (                              B 7.03).
β€’      Remove the complete soft top unit (                                N 2.01).

        IMPORTANT
        FROM the vehicle Ass. No. 41464, the movable side frame which supports the
        gearbox can be removed without having to lift the top unit. This is possible because
        the new top housing bays are equipped with openings which provide access to the
        side frame’s front fastening screws. Such screws can therefore be removed without
        lifting the top.

       β€’ Detach the pipes(1)which connect the vacuum tank to the chambers and to the
       solenoid valves for the pneumatic actuation system from the movable frame.


    http://127.0.0.1:8500/F131_S_E/dt/mo/d/d4_04.htm (1 of 16) [3/7/2006 11:57:31 PM]

--- Page 13 ---
http://127.0.0.1:8500/F131_S_E/dt/mo/d/d4_04.htm


   β€’ Remove the movable frame from the engine compartment.

   Re-attaching the frame

   β€’ Position the movable frame on the gearbox, making it rest on the frame supports.
   β€’ Secure the movable frame inserting the fastening screws (5), (7) and (8).


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d4_04.htm (11 of 16) [3/7/2006 11:57:31 PM]

--- Page 15 ---
#$


     1    Gearbox housing
     2    Intermediate plate
     3    Rear Cover
     4    Retaining plate for plate bearings
     5    Main shaft rear nut
     6    Reverse drive gear
     7    Main shaft ball bearing
     8    Main shaft
     9    Complete 5th speed gear
     10    Roller cage
     11    Complete 5th -6th speed double contact synchroniser
     12    Flexible ring
     13    6th speed gear spacer
     14    Complete 6th speed gear
     15    3rd- 6th speed gear shoulder ring nut
     16    Roller cage
     17    Complete 3rd speed gear
     18    Complete 3rd -4th speed double contact synchroniser
     19    Flexible ring
     20    Roller cage
     21    Complete 4th speed gear
     22    Support washer
     23    Main shaft roller bearing
     24    Main shaft front ring nut
     25    Front tapered roller bearing
     26    Spacer for bearings
     27    Rear tapered roller bearing
     28    Spacer for bushing
     29    Bearing holder bushing
     30    Lay shaft ring nut
     31    3rd-4th speed double gear
     32    5th-6th speed double gear
     33    2nd speed gear shoulder ring
     34    Complete 2nd speed gear
     35    Flexible ring
     36    Complete 1st- 2nd speed triple contact synchroniser
     37    1st speed gear bushing
     38    Roller cage
     39    Complete 1st speed gear
     40    1st speed gear shoulder wheel
     41    Lay shaft rear roller bearing

http://127.0.0.1:8500/F131_S_E/dt/mo/d/d4_05.htm (5 of 55) [3/7/2006 11:57:42 PM]

--- Page 16 ---
#$

 β€’ Remove the race with bearing's rollers (23) and the 4th gear speed support washer (22).
 β€’ Detach the 4th gear speed (21) and the roller cage (20) from the main shaft.


 β€’ Remove the flexible ring (19) and detach the sliding sleeve as well as the 3rd -4th speed
 synchroniser components (18).


 β€’ Insert the arms of extracting tool AV 3272 in the hub wedge seats and detach the complete 3rd -
 4th speed synchroniser (18) and the 3rd gear speed (17)..

 IMPORTANT
 Avoid letting the extracting tool arms grip under the toothing of the synchroniser or under the 3rd
 speed gear.


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d4_05.htm (15 of 55) [3/7/2006 11:57:42 PM]

--- Page 17 ---
#$


     Intermediate plate

 Once the bearing retaining plate (4) has been removed, it is possible to extract the tapered bearing
 (7). Use the AV 3264 punch for removing and fitting the bearing. The bearing has a ledge to help
 obtain the correct position on the plate.
 A roller casing (51), identical to the one on the rear cover, is installed in position with the oil pump on
 the intermediate plate, along with a ball bushing (E) for the fork support rod, which is identical to the
 one fitted inside the gearbox housing.
 β€’ Use the bushing extractor USAG 468S11 to remove said components.


 β€’ To extract the outer race (G) of the roller bearing (41), work from the oil pump side using a punch,
 and utilising the specific notches machined on the plate. Work with great care to avoid damaging the
 seat.


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d4_05.htm (25 of 55) [3/7/2006 11:57:42 PM]

--- Page 18 ---
#$


 Lubrication of the crown and pinion takes place by suction of the oil from the bottom of the housing
 and through a nozzle (54) which aims the oil jet directly on the crown toothing.
 A sheet (Q) is inserted in position with the ducts connecting the differential compartment with the
 one housing the gear shafts. This partially obstructs the said ducts and therefore prevents the oil
 from draining too quickly.


 Fig. 7 illustrates the gear lubrication circuit.


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d4_05.htm (35 of 55) [3/7/2006 11:57:42 PM]

--- Page 19 ---
#$


 β€’ Clean and degrease the surface of the lay shaft and the inner surface of the double gears (31 and
 32).

 IMPORTANT
 Put the two gears in the oven, in the correct assembly position, and leave them for at least two
 hours at a temperature of 140Β°C.

 β€’ Position the pinion on the base AV3255 (a) and use a tubular punch (b) to fit the 3rd – 4th speed
 double gear. Rest the newly formed assembly on the surface of the press and align it with the thrust
 axle before fitting the first gear (31).
 β€’ Leave it on load (10.000 kg) for at least 15 minutes and let the shaft cool down.
 β€’ Mount the 5th – 6th speed double gear (32) following the same procedure and using a tubular
 punch (c).


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d4_05.htm (45 of 55) [3/7/2006 11:57:43 PM]

--- Page 20 ---
#$


 β€’ Install the shoulder ring (50) on the roller casing (51) with its lubrication milling facing outwards
 and with its protrusion inserted between the plate clamps.
 β€’ Check that the second roller casing (51) and the new O-rings (62) are inserted on the rear cover.
 β€’ Grease the O-rings and the shoulder ring seat (50) on the cover, to keep it in position between
 the clamps during cover assembly. Make sure its lubrication milling is opposite the cover.
 β€’ Check that the centring dowels (60) and the new O-rings (61) are mounted on the plate before
 applying a strip of CAF4 sealant on the plate surface, as in the previous coupling.
 β€’ Mount the rear cover (3) on the plate (2).
 β€’ Apply the recommended locking product on the fixing screws' threading and tighten them to the
 prescribed torque, working crosswise.
 β€’ Proceed by fitting the differential unit (                     D 5.01).


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d4_05.htm (55 of 55) [3/7/2006 11:57:43 PM]

--- Page 21 ---
D5


  Calculating the spacer thickness

  The value of the tapered roller bearing pre-load is essential for correct functioning and for crown
  wheel and pinion durability: this value is determined by the thickness of the shoulders (7) and
  (12).
  It is possible to fit new bearings reusing the original spacers and checking that the rolling torque
  and the backlash correspond with the specified values (      D 1.01).
  The procedure we are going to illustrate shows how to determine the thickness of the shoulders,
  taking as references the values β€œR” and β€œS” of the seats on the gearbox housing, compared to
  the theoretic value (45,10 mm) of the distance between the crown and pinion axle β€œ0” (see Fig.
  2).


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d5_01.htm (10 of 21) [3/7/2006 11:57:48 PM]

--- Page 22 ---
D5


  At this re-assembly stage, it is a good rule to check the contact impression of the pinion's
  toothing on the crown.
  β€’ Apply red lead paint to the crown and make the crown and pinion do some revolutions.
  β€’ Check that the impression on the crown corresponds to 3/4 of the tooth side, both on the
  tensioning side and on the releasing one (see Fig. 5).


  The distance of the crown toothing's inner edge and the beginning of the impression should
  result between 5–8 mm.

http://127.0.0.1:8500/F131_S_E/dt/mo/d/d5_01.htm (20 of 21) [3/7/2006 11:57:48 PM]

--- Page 23 ---
http://127.0.0.1:8500/F131_S_E/dt/mo/d/d6_03.htm

             D6.03           TRANSMISSION CONTROL UNIT (TCU)


  The TCU is designed to: (see block diagram)


 β€’   acquire signals coming from sensors;
 β€’   interface with driver control device;
 β€’   interface with engine ECUs, drive control (ASR/MSR) and instrument panel;
 β€’   control the hydraulic sub-system.

 The signals that TCU must receive concern:
 β€’ engine revolutions;
 β€’ primary transmission shaft speed;
 β€’ clutch actuator position;
 β€’ gear selection actuator position;
 β€’ gear engagement actuator position;
 β€’ key turned to "running";
 β€’ driver door switch status;
 β€’ foot-brake pedal switch status;
 β€’ power unit oil pressure;
 β€’ CAN line signal (see block diagram);
 β€’ engine compartment lid on-off switch.


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d6_03.htm (1 of 2) [3/7/2006 11:57:52 PM]

--- Page 24 ---
http://127.0.0.1:8500/F131_S_E/dt/mo/d/d6_05.htm


 β€’ The Power Unit (A), fixed to the rear right hand part of the chassis;
 β€’ The actuator unit (B), fitted on the gearbox housing.
 In the hydraulic system there are also:
 β€’ an annular actuator for clutch movement
 β€’ a tank for oil collection (C);
 β€’ a set of lines (D) for hydraulic pressure use, linking the Power Unit to the gear and clutch
 actuators.


        WARNING
 In case of damage to pipes (after an accident, for egs.) that might have introduced foreign matters
 into the circuit, the Power Unit, the actuator and the respective pipes must be replaced.


 Replacing the hydraulic lines


       CAUTION
 The hydraulic system contains high pressure oil.

 NOTES
 As draining must be carried out at the end of the procedures, it is necessary to remove the actuator
 from the gearbox housing                          D 6.07).


 β€’ Detach the tube from the Power Unit         D 6.06) and from the actuator           D 6.07) by
 removing the union pipes or, by loosening the pipe restraining clamp if the pipe is rubber.

http://127.0.0.1:8500/F131_S_E/dt/mo/d/d6_05.htm (4 of 5) [3/7/2006 11:57:55 PM]

--- Page 25 ---
D6


  β€’ Unscrew the nuts (9) and remove the actuator unit from the gearbox housing, hitting with a
  plastic hammer on the unit's coupling flange, to detach the unit fixed to the housing with dope
  during assembly.


  Re-assembly
  β€’ Clean the actuator's and gearbox's coupling surfaces, to eliminate all traces of dope.
  β€’ Use AREXONS 2144 dope on the actuator coupling flange and assemble the unit on the
  gearbox housing.
  β€’ Tighten the fastening nuts to the prescribed tightening torque.
  β€’ Re-assemble the actuator's holding-protection brackets (4) and (5), fastening the nuts at the
  prescribed tightening torque.


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d6_07.htm (4 of 6) [3/7/2006 11:57:58 PM]

--- Page 26 ---
http://127.0.0.1:8500/F131_S_E/dt/mo/d/d6_08.htm


  Hydraulic Circuit Pressure Sensor (E)

  This sensor is fitted on the Power Unit and has the following features:


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d6_08.htm (8 of 10) [3/7/2006 11:58:00 PM]

--- Page 27 ---
http://127.0.0.1:8500/F131_S_E/dt/mo/d/d6_10.htm


   β€’ With the engine running and the car at rest, if the driver's door is opened without
   pressing the brake pedal, the gear is automatically disengaged and shifted to neutral.
   β€’ With the engine running and the car at rest, if the engine lid is opened without
   pressing the brake pedal, the gear is automatically disengaged and shifted to neutral.
   β€’ With the engine running and the car stopped, if a gear remains engaged for over 4
   seconds without operating on the brake or accelerator pedals, the gear is disengaged
   and shifted to neutral.
   β€’ With the engine running, car at rest and gear engaged, the gear is automatically
   disengaged and shifted to neutral after 10 minutes, even if the brake pedal is
   pressed.
   β€’ In case of severe system failure, which would not ensure a safe driving of the car,
   the engine stop is requested if the vehicle is at a standstill or running at a speed
   below 15 km/h.
   β€’ Only in the event of icy road-bed is it possible to request the "low grip" mode by
   pressing the relative push-button on the central console. Under these conditions, the
   clutch control is more gradual, pick-up is performed in second gear and the engine
   cannot be used if it exceeds 3100 rpm. The latter function is controlled by the
   automatic gear-shifting which is automatically activated any time that said threshold is
   exceeded. In sixth gear instead, the engine can be used in its thorough operating
   range.


http://127.0.0.1:8500/F131_S_E/dt/mo/d/d6_10.htm (4 of 4) [3/7/2006 11:58:02 PM]

View the complete manual on HeyDownloads β†’