PDF Workshop Manual SHERCO 450 SEF-R Engines - 646 KB

This official workshop manual provides everything you need to service, repair, and rebuild the engine for your SHERCO 450 SEF-R.

It includes detailed specifications, torque values, and step-by-step instructions for disassembly and assembly.

Whether you're a professional mechanic or a dedicated enthusiast, this manual is the definitive guide to maintaining your Sherco's high-performance engine.

Keep your bike race-ready with factory-approved procedures.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
MANUEL D’ATELIER
           MANUELI WORKSHOP
                    D’ATELIER MANUAL I MANUAL
                              I WORKSHOP      DE TALLER
                                          MANUAL I MANUAL DE TALLER

--- Page 3 ---
REMOVING/INSTALLING THE ENGINE

     ❱❘ Installing the engine in the frame
         Position the motor within the frame.
         Position the swing arm.
         Set the engine axes.
         Tighten the motor axes to 40 Nm.
         Tighten the swing arm pivot to 100 Nm.
         Set the frame guards and secure them with clamps.
         Put the right and left cylinder head supports. Put red thread lock and tighten to 25 Nm.
         Fit the left radiator and tighten to 10 Nm.
         Place the cooling hoses
         Make sure the engine is clean and place back the clutch receiver. Tighten to 10 Nm.
         Place the secondary chain and adjust the tension (see procedure on the user manual).
         Put the chain guard.
         Put the throttle body.
         Put the pencil coil.
         Put the exhaust pipe and secure it to the cylinder with its two springs.
         Reconnect the entire harness connected to the engine

         Reinstall the tank along with its vents (refer to the user manual).
        (starter case, TPS, water temperature sensor, pencil coil and injector).

         Reconnect the battery (refer to the user manual).


         WARNING
         Before reconnecting, check that the ignition key (SEF 450 standard) or the switch (450 SEF / R racing) is in the
         «OFF» position.

         Place back the saddle.
         Fill coolant and engine oil (refer to the user manual).


12                                                   450 SEF-R

--- Page 4 ---
CHECKING INDIVIDUAL PARTS
❱❘ Checking the crankshaft


                                                                               FRANÇAIS
  Radial clearance of the connecting rod :
    Place the crankshaft on V-blocks and place a         B           A
    Push [B] the connecting rod to the gauge
   dial gauge [A] against the connecting rod.

   and then in the opposite direction. The
   difference between those two measurements is
   the radialclearance.
   Radial clearance of the connecting rod :
       Standard : 0.008 mm – 0.012 mm
       Tolerated limit : 0.05 mm

   If the radial clearance exceeds the limit, the
   crankshaft must be replaced.


  Lateral clearance of the connecting rod :
   • Measure lateral clearance of the connecting
      rod [A].                                                    A
   Lateral clearance of the connecting rod :
      Standard : 0.6 mm - 0.85mm
      Tolerated limit : 1.1 mm

   If the radial clearance exceeds the tolerated
   limit, replace the crankshaft.


  Checking the runout :
   • Place the crankshaft on alignment devices or
     Vblocks, and place a gauge as shown in the
     image.
   • Then slowly turn the crankshaft. The maximum
     difference between the measurements
     corresponds with the offset of the crankshaft.
   Runout :                                                   A   A
     Standard : 0.02 mm maxi
     Tolerated limit : 0.08 mm

   If the offset is not correct, replace the crankshaft
   and align it so to be within tolerated limits.


                                                                          23

--- Page 5 ---
ENGINE ASSEMBLY
     ❱❘ Installing the cylinder
        • Seal the joint between the left and right casing
        with sealing dough.
        • Set the guide pins and a socket joint.
        • Lubricate the piston skirt.
        • Oil the cylinder.
        • Fit the cylinder paying attention to the rings.
        • Place the piston at TDC and the 1819 tool.


     ❱❘ Installing the cylinder head
        • Set the guide pins and the cylinder head
                                                                 1           4

        gasket.
        • Set the washers and nuts.
        • Screw the cylinder head in the order shown in
        the picture.
                                                                 3           2

        Pass 1
        Tightening torque of nuts 1/2/3/4 : 30 Nm.
                                                                     5   6

        Pass 2
        Tightening torque of nuts 1/2/3/4 : 50 Nm.
        Tightening torque of screws 5/6 : 10 Nm.


                                                                             1
                                                                     1


34                                                   450 SEF-R

--- Page 6 ---
INJECTION DIAGNOSTIC TOOL SYNERJECT


                                                                                                                   FRANÇAIS
                                                                       1


                                                                                       3


                                                                                 2


                                                                                                  4


            Synerject M3C Calculator                              Synerject Ø42mm Throttle Body

       N°         Description
       1          Stepper motor (idle control and engine brake)

       2          Injector

       3          Temperature / pressure sensor (TMAP)

       4          TPS : throttle position sensor


 1.2- Exxodiag diagnostic description tool reference 4967
 The diagnostic tool allows you to perform diagnostic operations, to update injection mapping and to verify
 certain information (serial number, operating hours, etc.).

 1.3- Composition of the diagnostic tool
 The case consists of a cable with a USB connector to MUX, a MUX device, a MUX cable to the motorcycle
 diagnostic connector, an installation CD, and a user manual.


                                                                                                              45

--- Page 7 ---
INJECTION DIAGNOSTIC TOOL SYNERJECT

      • You reach the following menu :


                                                                                                                    FRANÇAIS
      3.1- Identification : checking identification (serial number, vehicles operating hours calibration number).


      3.2- Measuring the parameters : general parameters (speed, pressure, stepper, etc).


56                                               450 SEF-R

--- Page 8 ---
INJECTION DIAGNOSTIC TOOL SYNERJECT

 3.7- Print screen function

 When liaising with technical support, and in order to allow rapid identification of potential problems, you can
 attach to your message screen print files with the F10 key of your keyboard.

 The «Identification» tab is definitely important for good communication (serial number of the bike, engine
 hours, calibration, etc.).


                                                                                                                   67

View the complete manual on HeyDownloads →