PDF Workshop Manual Hitachi ZX670LC-5G Hydraulic Excavator - 4 MB

This in-depth workshop manual provides complete service and repair information for the Hitachi ZX670LC-5G Hydraulic Excavator.

It is packed with detailed instructions, specifications, and schematics for every system.

Technicians will find this manual indispensable for diagnostics, disassembly, and reassembly procedures.

Ensure your excavator is maintained to the highest standards with this professional guide.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
PART NO.    WJBF90-EN-00


                                                          ZX670-5G
                                                          HYDRAULIC EXCAVATOR
                                                                                    Workshop Manual


                                                          WORKSHOP MANUAL
                                                                                    ZX670LC-5G
                                                                                    Hydraulic Excavator


URL:http://www.hitachi-c-m.com


                                                          WJBF90-EN-00


                                                                                    Service Manual consists of the following separate Part No.
                                                                                    Technical Manual (Operational Principle)          : Vol. No.TOJBF90-EN
                                                                                    Technical Manual (Troubleshooting)                : Vol. No.TTJBF90-EN
                          PRINTED IN JAPAN (K) 2013, 04                             Workshop Manual                                   : Vol. No.WJBF90-EN

--- Page 3 ---
SAFETY
General Precautions for Cab
   Before entering the cab, thoroughly remove all dirt and/or
    oil such as mud, grease, soil or stones that may mess up
    the cab from the soles of your work boots. If any controls
    such as a pedal is operated while with dirt and/or oil on
    the soles of the operator’s work boots, the operator’s foot
    may slip off the pedal, possibly resulting in a personal
    accident.
   Do not mess up around the operator's seat with parts,
    tools, soil, stones, obstacles that may fold up or turn
    over, cans or lunch box. The levers or pedals become
    inoperable if obstacle jams in operation stroke of the
    travel levers/pedals, pilot control shut-off lever or control
    levers, which may result in serious injury or death.
   Avoid storing transparent bottles in the cab. Do not
    attach any transparent type window decorations on
    the windowpanes as they may focus sunlight, possibly
    starting a fire.
   Refrain from listening to the radio, or using music
    headphones or mobile telephones in the cab while
    operating the machine.
   Keep all flammable objects and/or explosives away from
    the machine.
   After using the ashtray, always cover it to extinguish the
    match and/or tobacco.
   Do not leave cigarette lighters in the cab. When the
    temperature in the cab increases, the lighter may
    explode.
   Use proper floor mat dedicated to the machine. If another
    floor mat is used, it may be displaced and contact with
    the travel pedals during operation, resulting in serious
    injury or death.


                                                           SA-5

--- Page 4 ---
SAFETY
 Avoid swinging the upperstructure on slopes. Never
  attempt to swing the upperstructure downhill. The
  machine may tip over. If swinging uphill is unavoidable,
  carefully operate the upperstructure and boom at slow
  speed.
 If the engine stalls on a slope, immediately lower the
  bucket to the ground. Return the control levers to neutral.
  Then, restart the engine.
 Be sure to thoroughly warm up the machine before
  ascending steep slopes. If hydraulic oil has not warmed
  up sufficiently, sufficient performance may not be                           Travel Motor
  obtained.
 Use a signal person when moving, swinging or operating                       M104-05-008
  the machine in congested areas. Coordinate hand signals
  before starting the machine.
 Before moving machine, determine which way to move
  travel pedals/levers for the direction you want to go.
  When the travel motors are in the rear, pushing down
  on the front of the travel pedals or pushing the levers
  forward moves the machine forward, towards the idlers.
  An arrow-mark seal is stuck on the inside surface of the
  side frame to indicate the machine front direction.
 Select a travel route that is as flat as possible. Steer the
                                                                 Arrow -mark
  machine as straight as possible, making small gradual
  changes in direction.                                                        M178-03-001
 Before traveling on them, check the strengths of bridges
  and road shoulders, and reinforce if necessary.
 Use wood plates in order not to damage the road surface.
  Be careful of steering when operating on asphalt roads in
  summer.
 When crossing train tracks, use wood plates in order not
  to damage them.
 Do not make contact with electric wires or bridges.
 When crossing a river, measure the depth of the river
  using the bucket, and cross slowly. Do not cross the river
  when the depth of the river is deeper than the upper
  edge of the upper roller.
                                                                                    SA-011
 When traveling on rough terrain, reduce engine speed.
  Select slow travel speed. Slower speed will reduce
  possible damage to the machine.
 Avoid operations that may damage the track and
  undercarriage components.
 During freezing weather, always clean snow and ice from
  track shoes before loading and unloading machine, to
  prevent the machine from slipping.


                                                        SA-15

--- Page 5 ---
SAFETY

Practice Safe Maintenance
  To avoid accidents:
   Understand service procedures before starting work.
   Keep the work area clean and dry.
   Do not spray water or steam inside cab.
   Never lubricate or service the machine while it is moving.
   Keep hands, feet and clothing away from power-driven
    parts.

  Before servicing the machine:
  1. Park the machine on a level surface.
  2. Lower the bucket to the ground.
  3. Turn the auto-idle switch off.
  4. Run the engine at slow idle speed without load for 5
     minutes.
  5. Turn the key switch to OFF to stop engine.
  6. Relieve the pressure in the hydraulic system by moving
     the control levers several times.                             SA-028

  7. Remove the key from the key switch.
  8. Attach a “Do Not Operate” tag on the control lever.
  9. Pull the pilot control shut-off lever to the LOCK position.
 10. Allow the engine to cool.


   If a maintenance procedure must be performed with the
    engine running, do not leave the machine unattended.
   If the machine must be raised, maintain a 90 to 110˚
    angle between the boom and arm. Securely support any
    machine elements that must be raised for service work.
   Inspect certain parts periodically and repair or replace as
    necessary. Refer to the section discussing that part in the
    “MAINTENANCE” chapter in the operator's manual.                SA-527
   Keep all parts in good condition and properly installed.
   Fix damage immediately. Replace worn or broken parts.
    Remove any buildup of grease, oil, or debris.
   When cleaning parts, always use nonflammable
    detergent oil. Never use highly flammable oil such as fuel
    oil and gasoline to clean parts or surfaces.
   Disconnect battery ground cable (−) before making
    adjustments to electrical systems or before performing
    welding on the machine.


                                                           SA-25

--- Page 6 ---
SAFETY

Remove Paint Before Welding or Heating
 Hazardous fumes can be generated when paint is heated by
  welding, soldering, or using a torch. If inhaled, these fumes
  may cause sickness.
   Avoid potentially toxic fumes and dust.
   Do all such work outside or in a well-ventilated area.
    Dispose of paint and solvent properly.
   Remove paint before welding or heating:
  1. If you sand or grind paint, avoid breathing the dust.
     Wear an approved respirator.
  2. If you use solvent or paint stripper, remove stripper with   SA-029
     soap and water before welding. Remove solvent or paint
     stripper containers and other flammable material from
     area. Allow fumes to disperse at least 15 minutes before
     welding or heating.


Beware of Asbestos and Silicon Dust and Other
Contamination
 Take care not to inhale dust produced in the work site.
  Inhalation of asbestos fibers may be the cause of lung
  cancer. Inhalation of silicon dust or other contamination
  may cause sickness.
   Depending on the work site conditions, the risk
    of inhaling asbestos fiber, silicon dust or other
    contamination may exist. Spray water to prevent asbestos
    fibers, silicon dust or other contamination from becoming
    airborne. Do not use compressed air.
   When operating the machine in a work site where
    asbestos fibers, silicon dust or other contamination          SA-029
    might be present, be sure to operate the machine
    from the upwind side and wear a mask rated to
    prevent the inhalation of asbestos, silicon dust or other
    contamination.
   Keep bystanders out of the work site during operation.
   Asbestos fibers might be present in imitation parts. Use
    only genuine Hitachi Parts.


                                                         SA-35

--- Page 7 ---
SECTION 1

GENERAL
                                                                                  CONTENTS
Group 1 Precautions for Disassembling and
Assembling
  Precautions for Disassembling and
     Assembling..................................................................W1-1-1-1
Group 2 Tightening
  Tightening Bolts and Nuts...........................................W1-2-1-1
  Piping Joint.......................................................................W1-2-1-4
Group 3 Painting
  Painting specification....................................................W1-3-1-1
  Final painted color..........................................................W1-3-1-1
Group 4 Bleeding Air
  Bleeding Air from Hydraulic Oil Tank.......................W1-4-1-1
  Bleeding Air from Hydraulic System........................W1-4-1-2
  Bleeding Air from Fuel System...................................W1-4-1-3
  Bleeding Air from Radiator..........................................W1-4-1-4
Group 5 Pressure Release Procedure
  Hydraulic Circuit Pressure Release Procedure......W1-5-1-1
Group 6 Preparation
  Preparation before Inspection and
     Maintenance...............................................................W1-6-1-1


                                                                                      JBFW-1-1

--- Page 8 ---
SECTION 1 GENERAL
                                             Group 2 Tightening

  Precautions for Spilt Flange
IMPORTANT:
    Clean the sealing surfaces. Check if there are
     any scratches and roughness on the surface of
     the seal that cause oil leaks and damage to the
                                                                                                                     WDAA-01-02-005
     O-ring.
    Use only specified O-rings. Inspect O-rings for
     any damage. Do not file the O-ring surfaces.                       Incorrect
     When installing O-ring into a groove, use grease
     in order to hold O-ring in place.
    While tightening the bolt by hand, check that
     flange is installed to the port correctly. Do not
     pinch the O-ring.
    Tighten the bolts up and down, left and right
     alternately, in order to ensure even tightening
                                                                                                                     WDAA-01-02-006
     to the specified torque.
    Do not use air wrenches. Using an impact
     wrench often causes tightening of one bolt fully
     before tighten the others, resulting in damage
     to O-rings or uneven tightening of bolts.

  Nut and Bolt Locking
   Lock Plate
                                                                                                                      W105-01-01-008
IMPORTANT: Do not reuse the lock plates. Do not try
   to bend the same point twice.
                                                                    Correct                         Incorrect
   Split Pin
IMPORTANT: Do not turn in the loosening direction
   in order to align the grooves and holes on the nut.
                                                                              a                                 b
   Always turn in the tightening direction. Do not
   reuse the split pins.
                                                                         Correct           Correct              Incorrect

   Wire
IMPORTANT: Attach wire to bolts in the bolt-
   tightening direction. Do not reuse the wire.

                                                                              a
                                                                                                                     WDAA-01-02-007

                                                         a-   Bend along edge sharply          b-     Do not bend it round


                                                                           Correct        Correct
                                                                                                                        Incorrect


                                                                                     Correct            d            Incorrect
                                                                          c


                                                                                                                     WDAA-01-02-008

                                                         c-   Tighten                          d-     Loosen


                                                   W1-2-1-3

--- Page 9 ---
SECTION 1 GENERAL
                                                 Group 4 Bleeding Air

Bleeding Air from Fuel System
  Air in the fuel system may make the engine hard to
  start or make it run irregularly. After draining water and
  sediment from the fuel filter, replacing the fuel filter,
  cleaning the fuel solenoid pump strainer or running
  the fuel tank dry, be sure to bleed the air from the fuel
  system.

  Air Bleeding Procedures

dCAUTION: Fuel leaks may lead to fires.
  1. Check that fuel cock (1) on bottom of the fuel tank is
     opened.                                                            1
  2. Loosen priming pump (3).
  3. Loosen joint bolt (2) on the fuel main filter.

     j : 12 mm
  4. Supply fuel by reciprocating priming pump (3).
     After no air bubbles are spouted through joint bolt                    M1U1-07-015
     (2), tighten joint bolt (2).

     j : 12 mm                                                          2

  5. After tightening joint bolt (2), reciprocate priming
     pump (3) until its movement becomes slow.
  6. Tighten priming pump (3).
  7. Wipe off any spilled fuel.
  8. Start the engine. Check that no fuel leaks are
     present. If the engine does not start, repeat the
     above procedures from step 1.
                                                                3


                                                                            M111-07-046


                                                         W1-4-1-3

--- Page 10 ---
SECTION 2 MAINTENANCE STANDARD
                                              Group 1 Upperstructure

Main Pump
 1. Clearance between plunger outer diameter (A) and
    cylinder block bore diameter (B).
                                                                                                A   B

 B-A                               Unit: mm (in)
         Standard           Allowable Limit
        0.05 (0.002)         0.095 (0.004)
                                                                                                        W117-02-02-009


 2. Outer diameter (C) of shaft.

                                                                                                        C
 C                                 Unit: mm (in)
         Standard           Allowable Limit
         65 (2.56)            64.8 (2.55)


                                                                                                        W176-02-04-019
 3. Clearance (D) between plunger and shoe bottom
    and shoe thickness (E)

 D                                 Unit: mm (in)
         Standard           Allowable Limit
        0.2 (0.008)           0.45 (0.018)


 E                                 Unit: mm (in)
         Standard           Allowable Limit
                                                                                                            D
        8.5 (0.335)           8.3 (0.327)                                       E


                                                                                                        W117-02-02-011
 4. Clearance between small chamber inner diameter
    and servo piston

 F-G                               Unit: mm (in)
         Standard           Allowable Limit
       0.065 (0.0026)       0.085 (0.0033)


 5. Clearance between large chamber inner diameter
    and servo piston                                      F        G                                              G F


 F-G                               Unit: mm (in)
         Standard           Allowable Limit
                                                                   b                                                a
       0.07 (0.0028)         0.09 (0.0035)
                                                                                                        WDCD-02-01-001

                                                              a-       Small Chamber Diameter
                                                              b-       Large Chamber Diameter


                                                     W2-1-1-1

--- Page 11 ---
SECTION 2 MAINTENANCE STANDARD
                                               Group 2 Undercarriage

Upper Roller
  Roller


                                                                                        C


                                                                  A
                                                                                                             W166-03-06-007
                                                                  B


                                                                                                             Unit: mm (in)
                                         Standard                     Allowable Limit                  Remedy
               A                         118 (4.65)                          -
                                                                                                Cladding by welding and
               B                         240 (9.45)                          -
                                                                                                    finish or replace.
               C                         200 (7.87)                     [190 (7.48)]

fNOTE: Values in [ ] are just for reference.

  Axle and Bushing
                                                                                                             Unit: mm (in)
                                                      Standard             Allowable Limit               Remedy
      Axle              Outside Dia.                  75 (2.95)              [74.2 (2.92)]
                         Inside Dia.                  75 (2.95)                  [76 (2.99)]             Replace
     Bushing
                      Flange Thickness                4.5 (0.18)                 [3.7 (0.15)]

fNOTE: Values in [ ] are just for reference.


                                                          W2-2-4-1

--- Page 12 ---
SECTION 2 MAINTENANCE STANDARD
                                              Group 3 Front Attachment

ZX670LC-5 Class
                                              Unit: mm (in)
Front                 STD., H            BE
A                     600 (23.6)         610 (24.0)
B                     20 (0.79)          
C                     890 (35.0)         
D                     820 (32.3)         
E                     2164 (85.2)        2187 (86.1)
F                     662 (26.1)         693 (27.3)
G                     77 (3.03)          100 (3.94)
H                     10 ˚               
I                     0˚                 
J                     150 (5.91)         
K                     525 (20.7)         
L                     597 (23.5)         
M                     160 (6.30)         
N                     525 (20.7)         
O                     597 (23.5)         

fNOTE: 1.	Dimension A is different according to the arm
              type.
    		 2.	Dimension K and N: 525 mm (20.7 in) includes
           the clearance for shims in order to adjust the
           bucket clearance.
    		 3.	Dimensions H: 10 ˚, I: 0 ˚ indicate the angle of
           stopper.
    		 4.	Dimensions E, F and G are different according
           to the bucket type.


                                                         W2-3-1-5

--- Page 13 ---
SECTION 3 UPPERSTRUCTURE
                                                              Group 1 Cab

               1        2                3, 4                                        11     12    13      14


           A                                                                B


                                                          5


                                                          6, 7


                               6, 7      8, 9, 10
                                                    WDAA-03-01-052
                                                                                                                   WDAA-03-01-053
                                                                                       16           15
                   19         22
                                                                                             17          18
Detail A                                                              Detail B


                                                                                                                   WDAA-03-01-065
                                                    WDAA-03-01-062
                            20, 21, 22


   9. Open cover (1).                                                   13. Remove caps (3) (2 used). Remove screws (4) (2
                                                                            used). Remove cover (2) and duct (13).
 10. Remove caps (20) (2 used). Remove seals (21) (2
     used) and screws (22) (3 used). Remove cover (19).                 14. Remove bolts, washers (15) (2 used).
 11. Remove bolts, washers (6) (2 used) and washers (7)                      j : 17 mm
     (2 used).
                                                                        15. Remove bolt, washer (14). Remove cover (16).
       j : 13 mm
                                                                             j : 13 mm
 12. Remove caps (8) (3 used). Remove rubbers (9) (3
     used) and screws (10) (3 used). Remove cover (5).                  16. Remove screws (11) (2 used). Remove duct (12).
                                                                        17. Remove bolt, washer (18). Remove duct (17).

                                                                             j : 13 mm


                                                                 W3-1-1-3

--- Page 14 ---
SECTION 3 UPPERSTRUCTURE
                                                       Group 1 Cab


                                                                Detail A
                                                                                               1

                                                                                                                2, 13


                                                                    1

           A                      B


                                                                                                           WJBE-03-01-009


                                                                Detail B 3    4        5   6       7   7       8


                                               WJBE-03-01-008


                                                                                                           WJBE-03-01-010
                                                                     11, 12       10   9

 5. Connect cable (10).
 6. Install horn (9) with bolt, washer (8).

    j : 13 mm

    m : 10 N·m (1 kgf·m, 7.4 lbf·ft)
 7. Install clip (12) and bolt, washer (11).

    j : 17 mm

    m : 50 N·m (5 kgf·m, 37 lbf·ft)
 8. Connect connectors (7) (2 used).
 9. Install controller (6) with screws (5) (2 used).
10. Install connector (4) with screws (3) (4 used).
11. Install ground (13) with bolt, washer (2).

    j : 13 mm

    m : 10 N·m (1 kgf·m, 7.4 lbf·ft)
12. Connect connectors (1) (6 used).


                                                         W3-1-1-13

--- Page 15 ---
SECTION 3 UPPERSTRUCTURE
                                                 Group 1 Cab

Unit: mm


                                                        Section A


                                                                     WDAA-03-01-004


                               WDAA-03-01-031


a-   Chamfer along the Periphery                                     WDAA-03-01-003


                                                   W3-1-2-3

--- Page 16 ---
SECTION 3 UPPERSTRUCTURE
                                                            Group 1 Cab

Unit: mm

Rear Glass                                                               Right-Hand Glass


                                                    WDAA-03-01-039


Rear Left-Hand Glass
                                                                                                          WDAA-03-01-040


                                                                         Lower Door Glass


                                                    WDAA-03-01-041                                        WDAA-03-01-042


Spacer A                                       Spacer B                                        Spacer C


                              WDAA-03-01-043                                  WDAA-03-01-044              WDAA-03-01-045
a-   Two-Side Adhesive Tape                    a-    Two-Side Adhesive Tape


Dam Rubber


                              WDAA-03-01-046


                                                              W3-1-2-13

--- Page 17 ---
SECTION 3 UPPERSTRUCTURE
                                           Group 2 Counterweight

Removal and Installation of Counterweight


                      5


                                           WJBA-03-02-001
                                       1


 Removal
 1. Set the machine position for inspection and
    maintenance. (Refer to W1-6-1.)
 2. Open door (1).
 3. Disconnect connector (5).


                                                      W3-2-1-1

--- Page 18 ---
SECTION 3 UPPERSTRUCTURE
                                              Group 3 Main Frame


                            3


2


1

                                                       4

                                              5, 6


                    3

                                           WJBA-03-03-002


5. Install stopper (4) with washers (6) (4 used) and
   bolts (5) (2 used).

    j : 22 mm

    m : 140 N·m (14 kgf·m, 103 lbf·ft)
6. Connect hose (2).

    j : 17 mm

    m : 25 N·m (2.5 kgf·m, 18.5 lbf·ft)
7. Connect hose (1).

    j : 27 mm

    m : 80 N·m (8 kgf·m, 59 lbf·ft)
8. Connect hoses (3) (4 used).

    j : 41 mm

    m : 200 N·m (20 kgf·m, 148 lbf·ft)


                                                       W3-3-1-7

--- Page 19 ---
SECTION 3 UPPERSTRUCTURE
                                                 Group 4 Engine


                                            1    2       3          2   2   4


                                                                                2


                    4

                                                                                    4


                                                                                    3


                                                                                        WJBF-03-04-004
                                 2                   3


dCAUTION:
 (155 lb)
          The beam (1) assembly weight: 70 kg

 26. Attach the nylon slings onto the beam (1) assembly.
     Hoist and hold the beam (1) assembly.
 27. Remove bolts, washers (2) (8 used).

     j : 19 mm
 28. Remove bolts, washers (3) (5 used).

     j : 19 mm
 29. Remove bolts, washers (4) (4 used). Remove the
     beam (1) assembly.

     j : 19 mm


                                                         W3-4-1-9

--- Page 20 ---
SECTION 3 UPPERSTRUCTURE
                                                  Group 4 Engine

                                                                           5


                                                             3


               4
                                                                                   WJBE-03-04-009
                       3


                                        1   WJBE-03-08-013
                                    2

 72. Remove bolts (1) (4 used) and washers (2) (4 used).

     j : 22 mm                                                     6   7

 73. Remove bolts, washers (4) (4 used). Remove bracket
     (3).

     j : 19 mm                                                                 8

 74. Remove bolts (7) (4 used) and washers (6) (4 used)
     at the counterweight side. Remove bracket (8).

fNOTE: LOCTITE # 262 has been applied onto bolts (7) (4
   used).
     j : 22 mm
 75. Remove bracket (8) at the front attachment side in
                                                                                   WJBE-03-04-010
     the same way as step 74.
 76. Remove the adapter with engine (5) attached if
     necessary.


                                                      W3-4-1-19

--- Page 21 ---
SECTION 3 UPPERSTRUCTURE
                                                    Group 4 Engine


1    2   3


                                                4

                                       5

                                   6        WJBF-03-04-005


44. Connect pipe (2) with clamps (1, 3) (2 used for each).

    m : 10 N·m (1 kgf·m, 7.4 lbf·ft)
45. Connect the pipe (5) assembly with clamps (4) (2
    used) and clamp (6).

    m : 10 N·m (1 kgf·m, 7.4 lbf·ft)


                                                       W3-4-1-29

--- Page 22 ---
SECTION 3 UPPERSTRUCTURE
                                           Group 5 Radiator Assembly

Replacement of Radiator and Oil Cooler
           1                2


                                             WJBF-03-08-001

IMPORTANT: Cap the open ends in case the hoses
   and pipes have been disconnected. In addition,
   attach an identification tag onto the connectors,
   hoses, and pipes for assembling. Connect the
   hoses and install the clips in case the clips which
   secure the hoses have been removed.
  Removal
  1. Set the machine position for inspection and
     maintenance. (Refer to W1-6-1.)

dCAUTION:    Bleed air from the hydraulic oil tank.
 (Refer to W1-4-1.)
  2. Remove bolts, washers (2) (6 used). Remove cover
     (1).

     j : 17 mm
  3. Drain off hydraulic oil by using an oil feed pump.

fNOTE: Total oil amount: 750 L (198 US gal)


                                                          W3-5-1-1

--- Page 23 ---
SECTION 3 UPPERSTRUCTURE
                                           Group 5 Radiator Assembly

                                                              2
                                            1


                                        11, 12                                3

                                                 9, 10                             4


                                                                                            5
                                                                                        6


                                                                                            7
                                                                                        8


                                                                                                            WJBF-03-05-012


 35. Remove bolts, washers (11) (6 used) and clips (12) (6        39. Remove bolts, washers (5) (2 used). Remove the
     used).                                                           bracket (6) assembly.

     j : 19 mm                                                        j : 19 mm

dCAUTION: Cover (2) weight: 35 kg (78 lb)                         40. Remove bolts, washers (7) (2 used). Remove the
                                                                      bracket (8) assembly.
 36. Remove bolts, washers (1) (6 used). Remove cover
     (2).                                                             j : 19 mm
     j : 19 mm

dCAUTION: Cover (3) weight: 34 kg (75 lb)
 37. Remove bolts, washers (4) (6 used). Remove cover
     (3).

     j : 19 mm
 38. Remove clamp (9). Disconnect hose (10).


                                                         W3-5-1-11

--- Page 24 ---
SECTION 3 UPPERSTRUCTURE
                                          Group 5 Radiator Assembly


                                                      1
                                                     2
                                                     3
                                                 1
                                                          2

                                                                    1
                                                                3


                                           6 4


                                                      5
                                                 6
                                                                        WJBF-03-05-002


64. Remove clamps (1) (16 used). Disconnect hoses (2,
    3) (2 used for each).
65. Remove bolts (6) (4 used). Disconnect pipes (4, 5).

    j : 19 mm


                                                          W3-5-1-21

--- Page 25 ---
SECTION 3 UPPERSTRUCTURE
                                              Group 5 Radiator Assembly


                                                         a       1

View the complete manual on HeyDownloads →