PDF Shop Manual Komatsu PC750-7 PC800-7 - 6 MB

This is the factory shop manual for the Komatsu PC750-7 and PC800-7 hydraulic excavators.

It offers comprehensive service and repair information, covering everything from the engine to the hydraulic systems.

The manual provides detailed troubleshooting, testing, and adjusting procedures, along with disassembly and assembly instructions.

This guide is indispensable for any technician working on these large excavators.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram βœ‰Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
SEBM008707


1


MACHINE MODEL                           SERIAL NUMBER

PC750-6                                 10001 and up
PC750SE-6                               10001 and up
PC750LC-6                               10001 and up
PC800-6                                 30001 and up
PC800SE-6                               30001 and up

β€’   This shop manual may contain attachments and optional equipment that are not available
    in your area. Please consult your local Komatsu distributor for those items you may
    require. Materials and specifications are subject to change without notice.

β€’   PC750, 800-6 mount the SAA6D140-2 engine.
    For details of the engine, see the 6D140-2 Series Engine Shop Manual.

Β© 2000 1
All Rights Reserved
                                                                                   00-1
Printed in Japan 08-00(01)                                                           u

--- Page 3 ---
FOREWORD                                                               HOW TO READ THE SHOP MANUAL


HOW TO READ THE SHOP MANUAL

VOLUMES                                                    REVISED EDITION MARK

Shop manuals are issued as a guide to carrying             When     a manual        is revised,   an edition     mark
out repairs. They are divided as follows:                  (@@@....I   is recorded        on the     bottom    of the
Chassis volume: Issued for every machine model             pages.
Engine volume: Issued for each engine series
                                  Each issued as one
Electrical volume:
                                  volume to cover all      REVISIONS
Attachments volume:
                              I   models
                                                           Revised pages are shown in the LIST OF RE-
These various volumes are designed to avoid                VISED PAGES next to the CONTENTS   page.
duplicating the same information.    Therefore, to
deal with all repairs for any model , it is neces-
sary that chassis, engine, electrical and attach-
                                                           SYMBOLS
ment volumes be available.
                                                           So that the shop manual can be of ample prac-
DISTRIBUTION       AND UPDATING                            tical use, important safety and quality portions
                                                           are marked with the following symbols.
Any additions, amendments     or other changes
will be sent to KOMATSU distributors.   Get the
most up-to-date information before you start any
work.

FILING METHOD
1. See  the page number on the bottom of the                Symbol        Item                    Remarks
   page. File the pages in correct order.
                                                                                       Special safety precautions are
2. Following examples
   page number.
                        show how to read the

   Example 1 (Chassis volume):
                                                              a          Safety        necessary
                                                                                       the work.
                                                                                                   when performing


                                                                                       Special technical precautions
   10 -3                                                                               or other precautions    for pre-
                                                               *        Caution        serving standards are neces-
                     Item number (10. Structure                                        sary when     performing     the
                     and Function)                                                     work.
                     Consecutive page number for
                                                                                       Weight of parts of systems.
                     each item.                                                        Caution necessary when se-

   Example      2 (Engine volume):                          el kg       Weight         lecting hoisting wire, or when
                                                                                       working posture is important,
                                                                                       etc.

                                                                                       Places that require special at-
                                                                       rightenins
                     Unit number (I. Engine)                                           tention   for the tightening
                                                                        torque         torque during assembly.
                     Item number (2. Testing and
                     Adjusting)                                                        Places to be coated with ad-
                                                                         Coat
                     Consecutive page number for                                       hesives and lubricants, etc.
                     each item.
                                                                                       Places where oil, water or fuel
                                                                       Oil, water      must be added, and the ca-
3. Additional    pages:    Additional   pages are indi-                                pacity.

   cated   by a hyphen      (-1 and number     after the                               Places where   oil or water
   page number.       File as in the example.                            Drain         must be drained, and quan-
   Example:                                                                            tity to be drained.

   IO-4                                   12-203
   10-4-l -
          k        Added    pages -c:~~~~~::
   1O-4-2
   IO-5                                   12-204


00-6

--- Page 4 ---
FOREWORD                                                                                                                                        CONVERSION           TABLE


CONVERSION TABLE

METHOD         OF USING           THE CONVERSION                         TABLE
     The Conversion            Table        in this section                is provided            to enable               simple      conversion       of figures.     For
     details   of the method              of using the Conversion                         Table,        see the example                  given below.


EXAMPLE
.    Method     of using the Conversion                        Table to convert               from millimeters                     to inches
1.    Convert    55 mm into inches.
      (1) Locate the number                 50 in the vertical column at the left side, take this as @, then draw a horizontal
           line from @.
      (2) Locate the number                  5 in the row across the top, take this as @I, then draw a perpendicular                                                      line
           down from 0.
      (3) Take the point where                    the two lines cross as 0.                         This point @ gives the value when                          converting
           from millimeters              to inches.          Therefore,           55 mm = 2.165 inches.

2.    Convert 550 mm into inches.
      (I) The number 550 does not appear in the table, so divide by 10 (move the decimal point one place
           to the left) to convert it to 55 mm.
      (2) Carry out the same procedure as above to convert 55 mm to 2.165 inches.
      (3) The original value (550 mm) was divided by 10, so multiply 2.165 inches by 10 (move the decimal
          point one place to the right) to return to the original value. This gives 550 mm = 21.65 inches.


                                                                                                                             03
      Millimeters        to inches                                                                                                                     1 mm = 0.03937 in

                                     0               1               2               3              4                 5;             6          7          8          9

                     0           0                0.039           0.079           0.118         0.157                   0.197;     0.236       0.276     0.315       0.354
                    10           0.394            0.433           0.472           0.512         0.551                   0.591 i    0.630       0.669     0.709       0.748
                    20           0.787            0.827           0.866           0.906         0.945                   0.984;     1.024       1.063     1.102       1.142
                    30           1.181            1.220           1.260           1.299         1.339                   1.378;     1.417       1.457     1.496       1.536
                    40           1.575            1.614           1.654           1.693         1.732                   1.772;     1.811       1.850     1.890       1.929
                                                                                                                     @         i
                    50             1.969             2.008          2.047             2.087
                ,............,.............,.............~............................,          2.126
                                                                                              . .. . .. . .. . . . . . 12.1651     2.205       2.244     2.283       2.323
                    60             2.362             2.402          2.441             2.480      2.520                  2.559      2.598       2.638     2.677       2.717
                    70             2.756             2.795          2.835             2.874      2.913                  2.953      2.992       3.032     3.071       3.110
                    80             3.150             3.189          3.228             3.268      3.307                  3.346      3.386       3.425     3.465       3.504
                    90           3.543            3.583           3.622           3.661          3.701                  3.740      3.780       3.819     3.858       3.898


00-16

--- Page 5 ---
GENERAL                                                              SPECIFICATION DRAWINGS


PC750LC-6                                                                           Unit: mm


                                                                                               020906


            fl The figures in ( ) show the value when the track width is reduced.
            fl The figures in [ ] show the value for the long arm specification.

01-3-1
01-16
  q

--- Page 6 ---
GENERAL                                                                                   SPECIFICATIONS


LOADING       SHOVEL

                         Machine      model                                     PC750-6

                         Serial    Number                                    10001 - 10238

                         Bucket capacity                          m3               3.8

                       Weight     of machine              f       kg             74β€˜435

          Max. digging      depth                                 mm             3,455

          Max. vertical wall depth                                mm                -

          Max. digging      reach                                 mm             9,960

          Max. reach at ground           level                    mm              9,595

          Max. digging      height                                mm             10,565

          Max. dumping          height                            mm              6,825

    Max. digging        force                                   kN {kg1      431.5 {44,0001

    Swing     speed                                               rpm              5.7

    Swing     max. slope angle                                   deg.              14

    Travel speed                                                 km/h        Low speed: 2.7
                                                                             High speed: 4.2

    Gradeability                                                 deg.              35

    Ground     pressure     (standard      double
      grouser shoe width: 710 mm)                             kPa {kg/cm*:    101.99 {I.041

    Overall    length                                             mm              9,760

    Overall    width                                              mm

    Overall    width    of track (when        extended)           mm          3,490 (4,210)

    Overall    height                                             mm              5,375

    Overall    height to top of machine                           mm              4,490

    Ground     clearance        of upper structure                mm              1,555

    Min. ground        clearance                                  mm               840

    Tail swing     radius                                         mm              4,300

    Min. swing        radius of work equipment                    mm              5,940

    Height of work equipment at min. swing radiu!s                mm              6,925

    Length of track on ground                                     mm              4,500

    Track gauge        (when      extended)                       mm          2,780 (3,500)

    Height    of machine        cab                               mm              3,495


01-9-l
  0

--- Page 7 ---
GENERAL                                                                                          WEIGHT TABLE


WEIGHT TABLE
g This weight table is a guide for use when transporting             or handling    components

BACK HOE
                                                                                                             Unit: kn

                           Machine      model               PC750-6                PC750SE-6      PC75OLC-6

                           Serial   Number                10001 - 10238       10001 - 10238      10001 - 10238

  Engine assembly                                             2,347                  2,347           2,347

  l   Engine                                                  1,475                  1,475           1,475

  l   PTO (incl. lubricating        piping)                    500                    500             500

  l   No. 1 pump                                               198                    198             198

  l   No. 2 pump                                               156                    156             156

  l   Control,    PTO lubrication       pump                    18                     18             18

  Radiator      assembly                                       260                    260             260

  Oil cooler assembly                                          200                    200             200

  Hydraulic      tank (excl. hydraulic        oil)             474                    474             474

  Revolving      frame     (incl. left and right decks)       6,340                  6,340           6,340

  Operator’s      cab                                          290                    290             290

  Swing       machinery                                        900                    900             900

  Swing       motor    assembly                                 85                     85             85

  Travel      motor assembly                                 145x2                  145 x 2         145x2

  L.H. 5-spool        control   valve                          245                    245             245

  R.H. 4-spool        control valve                            240                    240             240

  Center swivel joint                                           69                     69             69

  Counterweight                                               9,000                  9,000           9,000

  Track frame         assembly                                19,546                 19,546         19,970

  l   Center frame                                            5,200                  5,200           5,200

  l   Track frame                                           2,630 x 2              2,630 x 2       2,820 x 2

  l   Carrier    roller                                      71.5 x 6               71.5 x 6        71.5 x 6

  l   Track roller                                           136 x 16               136 x 16       136 x 18

  l   Idler cushion       assembly                           782 x 2                782 x 2         782 x 2

  l   Idler                                                  450 x 2                450 x 2         450 x 2

  l   Final drive assembly                                  1,341 x 2               1,341 x 2      1,341 x 2

  l   Swing      circle assembly                              1,335                   1,335          1,335


01-10
  0

--- Page 8 ---
GENERAL                                                                FUEL, COOLANT    AND   LUBRICANTS


FUEL, COOLANT                   AND LUBRICANTS
                                               AMBIENT     TEMPERATURE
                                (IND OF
         RESERVOIR
                                 FLUID


 Engine oil pan


 PTO case                       Engine
                                  oil

 Swing     machinery   case

 Final drive case (each side1
                                          I     I    I     I   I   I     I
 Hydraulic    system                                                               800            440


 Idler (I each)                                                                    0.55           -

                                 Gear
 Track roller (I each)                                                             0.42           -
                                  oil

 Carrier roller (I each)                                                           0.62           -


                                Diesel                                                            -
 Fuel tank                                                                         880
                                 fuel


 Cooling     system             Coolant   Add antifreeze                               85         -
                                                                               I              I


01-l 2

--- Page 9 ---
STRUCTURE AND FUNCTION                           SWING MACHINERY


SWING MACHINERY

                          1. Swing pinion (No. of teeth: 12)
                          2. Cover
                          3. Case
                          4. Coupling
                          5. No. 2 planet gear (No. of teeth: 32)
                          6. No.2 ring gear (No. of teeth: 83)
                          7. No. 1 ring gear (No. of teeth: 83)
                          8. Cover
                          9. Dipstick
                         10. Swing motor
                         11. No. 1 sun gear (No. of teeth: 23)
                         12. No. 1 planetary carrier
                         13. No. 2 sun gear (No. of teeth: 17)
                         14. No. 2 planetary carrier
                         15. Drain plug


                         Specification

                         Reduction ratio: 23 + 190 x 17 + 83
                                             23         17
                                          = 54.4757


                                                                    020906


10-8
  w

--- Page 10 ---
I     I

          1. Boom      cylinder        g    s
          2.   Bucket cylinder         d    g
          3.   Arm cylinder
          4.   Swing motor
          5.   Return oil filter
          6. Oil cooler
          7. R.H. 4-spool         control    valve
          8. L.H. 5-spool         control    valve
          9. Line oil filter
         10. No. 1 pump
         11. Control pump
         12. No. 2 pump
         13. L.H. travel motor
         14. Hydraulic   tank
         15. Center swivel joint
         16. L.H. PPC valve
         17. R.H. PPC valve
         18. Travel PPC valve
         19. Accumulator
         20. Drain oil filter
         21. Pilot oil filter
         22. PPC control      relief       valve


020906

--- Page 11 ---
STRUCTURE AND FUNCTION                                                              HYDRAULICPUMP


l   No. 2 pump
    HPV95+95

                                               Pdl   1   PA1       PA2       Pd21


                                             Pecn         Psv      Pt        Pd     Pecn


                                                                                           SDPOl540


1. Front pump          PAI. Discharge port                          Psv.     Servo     basic   pressure
2. Front servo valve   PAI. Discharge port                                   supply Port
3. Rear servo valve    PA2. Discharge port                           Pecn.   CO, NC valve output
4. NC valve            Ps.  Suction port                                     pressure detection port
5. Rear pump           Pt.  Jet sensor upstream pressure IN port    Pdll.    Drain port
                       Pd.  Jet sensor downstream    pressure IN    Pd21.    Drain port
                            P0r-t


                                                                                                1O-23
                                                                                                  0

--- Page 12 ---
STRUCTURE AND FUNCTION                                                                    NO. 1 PUMP


Operation
1) Operation in direction of increase of pump discharge amount (max. angle)


                                                                                                           020906

β€’   The control pump pressure Psv is taken to            drain chamber e. As a result, servo piston
    port a.                                              chamber f is also interconnected with cham-
    Signal pressure Pecn from the NC valve is            ber e through port g and port d.
    taken from port b to chamber c.                      At the same time, port a is interconnected
β€’   When signal pressure Pecn rises, control pis-        with port h, so the oil flows through port i to
    ton (8) is pushed to the left by the hydraulic       servo piston chamber j, pushes servo piston
    pressure in chamber c, and stops at a point          (19) to the left, increases the swash plate
    where it balances the pressure of springs (4)        angle in the main piston pump and increases
    and (4A).                                            the pump discharge amount.
    At the same time, arm (6) uses servo piston      β€’   When servo piston (19) moves, arm (6) ro-
    (19) as a fulcrum and sways to the left in the       tates clockwise with its center at pin (7).
    same way as control piston (8). This moves           Guide spool (13) is moved to the right and
    guide spool (13) to the left.                        closes port a, port d and port h, so the dis-
β€’   When guide spool (13) moves, port a and              charge increases by an amount that matches
    port d are closed and port d is connected to         signal pressure Pecn.


10-30
    w
    u

--- Page 13 ---
STRUCTURE AND FUNCTION                            NO. 1 PUMP


         CO valve                NC valve
         1. Plug                  7. Plug
         2. Piston                8. Sleeve
         3. Spring                9. Piston
         4. Spool                10. Spool
         5. Piston               11. Spring
         6. Plug                 12. Plug


         PA1I : Main pump pressure IN port
         PA1o : Main pump pressure OUT port
         PA2I : Main pump pressure IN port
         PA2o : Main pump pressure OUT port
         Pe1 : TVC valve output pressure front, rear in-
                terconnection port
         Pe2 : TVC valve output pressure IN port
         Pc   : CO selector pilot port
         Pd : Jet sensor downstream pressure IN port
         Pt   : Jet sensor upstream pressure IN port
020906


         Pdr1 : TVC valve drain IN port
         Pdr2 : CO, NC valve drain OUT port
         Psv1 : Servo basic pressure IN port
         Psv2 : Servo basic pressure OUT port
         Pecn : CO, NC valve output pressure OUT port


                                                            10-38-1
                                                               u

--- Page 14 ---
STRUCTURE AND FUNCTION                               NO. 2 PUMP


PC750, PC750SE, PC750LC-6 Serial No.: 10239 and up
PC800, PC800SE-6          Serial No.: 30175 and up


                                                                  020906


Psv1 : Servo valve basic pressure port
Psv1A : Servo piston output pressure port
Psv1B : Servo valve output pressure port
Psv2 : Servo valve basic pressure port
Psv2A : Servo piston output pressure port
Psv2B : Servo valve output pressure port


10-44-4
    u

--- Page 15 ---
STRUCTURE AND FUNCTION       L.H. 5-SPOOL CONTROL VALVE


L.H. 5-SPOOL CONTROL VALVE


                                                          020906


10-52
  w

--- Page 16 ---
STRUCTURE AND FUNCTION                                                    SWING MOTOR


SUCTION-SAFETY VALVE

Function
β€’ When the swing is stopped, the outlet port
   circuit of the motor is closed by the control
   valve, but the motor continues to be turned
   by the inertia of the swing. As a result, the
   pressure at the outlet port of the motor be-
   comes abnormally high and there is danger
   that the motor will be damaged.
β€’ The safety valve is installed to prevent this
   problem. It acts to release the abnormally
   high pressure oil from the outlet port of the
   motor and send it to port S. At the same
   time, it also functions as a swing brake.                     S
β€’ The suction valve supplies an amount of oil
   equivalent to the amount of oil released by
   the safety valve. It sends this oil from port S
                                                         MB           MA
   to the inlet port of the motor to prevent any
   cavitation.
                                                          Control valve
Operation
                                                                               SAP00245
1. When starting swing
β€’ If the swing control lever is operated to swing


                                                                                          020906
   to the right, the pressurized oil from the
   pump passes through the control valve and
   it supplied to port MA.
β€’ When this happens, the pressure at port MA
   rises and the starting force is generated in      1                             2
   the motor, so the motor starts to turn.
   The oil from the outlet port of the motor
   flows from port MB through the control valve
   and returns to the tank.
2. When stopping swing
β€’ When the swing control lever is returned to
   the neutral position, no more pressurized oil
   is supplied from the pump to port MA.
   At the same time, the oil from the outlet
   port of the motor returns from the control
   valve to the tank, and the circuit is closed.
                                                                  S
β€’ The pressure at port MB rises, and rotating
   resistance to the motor is generated, so the
   brake starts to take effect.
   If the pressure at port MB rises to the set           MB           MA
   pressure of safety valve (1), safety valve (1)
   opens and releases the pressurized oil at
                                                          Control valve
   port MB to port S.
β€’ No pressurized oil is supplied at port MA,                                   SAP00246

   but the swing continues, so negative force
   is generated.
   When this negative pressure drops to the
   set pressure of suction valve (2), suction
   valve (2) opens and oil is supplied from port
   S to prevent cavitation.


10-62
  w

--- Page 17 ---
STRUCTURE AND FUNCTION                                          TRAVEL MOTOR


1-4 Relief valve


                                                      1.   Shockless piston
                                                      2.   Poppet
                                                      a.   Poppet orifice
                                                      b.   Relief housing orifice
                                                      c.   Piston stroke


Function
In addition to the pressure control function, this
relief valve has a shockless function (2-stage


                                                                                    020906
pressure increase function). This acts to reduce
the shock generated at the beginning when the
speed is reduced (when the machine is stopped).


Operation
1) When relief valve starts to be actuated (1st
   stage)
   The area receiving the pressure which lifts
   poppet (2) becomes area S1 of the poppet
   seat.
   For this reason, it has a much larger pres-
   sure-receiving area than the pressure-receiv-
   ing area when it is set (S1 – S2), so the relief
   actuating pressure becomes a low pressure
   of approx. 15.7 MPa {160 kg/cm2}.
   This condition is maintained until the move-
   ment of shockless piston (1) is completed
   (approx. 0.25 sec).

2) When movement of shockless piston is com-
   pleted (2nd stage)
   The pressure in the relief valve spring cham-
   ber rises, the pressure on both sides of pop-
   pet (2) becomes the same, and it becomes
   the specified set pressure.

    fl Set pressure and amount of adjustment
       Amount of adjustment for one turn:
       Approx. 7.8 MPa {80 kg/cm2}


10-72
  w

--- Page 18 ---
STRUCTURE AND FUNCTION                              WORK EQUIPMENT, SWING PPC VALVE


Operation
1) At neutral
   Ports A and B of the control valve and ports
   P1, P2, P3, and P4 of the PPC valve are con-
   nected to drain chamber D at the bottom.
   (Fig. 1)


                                                                                      020906
2) Fine control (neutral β†’ fine control)
   When piston (4) starts to be pushed by disc
   (5), retainer (9) is pushed. Spool (1) is also
   pushed by metering spring (2) and moves
   down.
   When this happens, port P1 is shut off from
   drain chamber D. At almost the same time,
   it is connected to pump pressure chamber
   PP, and the pilot pressure of the control
   pump is sent from port P1 to port A.
   When the pressure at port P1 rises, spool (1)
   is pushed back. Fine control hole f is shut
   off from pump pressure chamber PP. At al-
   most the same time, it is connected to drain
   chamber D, so the pressure at port P1 es-
   capes.
   As a result, spool (1) moves up and down
   until the force of metering spool (2) is bal-
   anced with the pressure of port P1.
   The relationship of the positions of spool (1)
   and body (10) does not change until retainer
   (9) contacts spool (1).
   Therefore, metering spring (2) is compressed
   in proportion to the travel of the control le-
   ver, so the pressure at port P1 also rises in
   proportion to the travel of the control lever.
   In this way, the spool of the control valve
   moves to a position where the pressure of
   chamber A (same as pressure at port P1)
   and the force of the return spring of the
   control valve spool are balanced. (Fig. 2)


10-82
   w

--- Page 19 ---
STRUCTURE AND FUNCTION                                  AIR CONDITIONER


AIR CONDITIONER
AIR CONDITIONER PIPING
STD CAB SPECIFICATION


                                                                          020906


1.   Duct                         A. Fresh air
2.   Condenser                    B. Recirculated air
3.   Air conditioner compressor   C. Hot air/cold air
4.   Hot water return piping
5.   Hot water pickup piping
6.   Refrigerant piping
7.   Receiver tank
8.   Air conditioner unit


10-136
10-91-1
     we

--- Page 20 ---
STRUCTURE AND FUNCTION                                                ENGINE CONTROL


ENGINE CONTROL


                                                                                             020906


1.   Battery relay                      Function
2.   Battery                            β€’ The engine can be started and stopped sim-
3.   Starting switch                       ply by using starting switch (3).
4.   Fuel control dial                  β€’ A dial-type engine control is used to control
5.   Fuel injection pump                   the engine speed. Engine throttle and pump
6.   Governor motor                        controller (8) receives the control signal from
7.   Starting motor                        fuel control dial (4), sends a drive signal to
8.   Engine throttle, pump controller      governor motor (6), and controls the angle
                                           of the governor lever in fuel injection pump
                                           (5).


10-98
     w

--- Page 21 ---
STRUCTURE AND FUNCTION                                          MACHINE CONTROL SYSTEM


2.   Electronic OLSS function
     Pump control system


                                                                   Swash      plate   type       tandem        Pump
     Engine
                      Electric
                                                                    (No.   I PumPi
      inrsction       .o,o,


                                                                   Pump     control     system


                                                              Solenoid
                                                              valve
                                                                                                     monitor          panel
                                                                                                      /                       β€˜\


                  Ensine         throttle,pump   controller

                                                                                                               SWPO6658


.    Interconnected   control of all pumps is car-
     ried out by one TVC valve.
.    DH mode: Total horsepower       control by en-
     gine speed sensing
     H mode: Total horsepower        control by en-
                gine speed sensing

View the complete manual on HeyDownloads β†’