PDF Shop Manual Komatsu 930E-4 Dump Truck - 2 MB
This is the complete shop manual for the Komatsu 930E-4 electric drive dump truck.
It contains detailed service procedures, specifications, and troubleshooting guides for every system on this massive machine.
Professional technicians rely on this manual for everything from routine maintenance to complex overhauls.
This guide is essential for keeping your 930E-4 operating at peak efficiency and safety.
PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
PDF viewer loading area
Text Preview from This Manual
The text below was extracted from the visible preview pages to help you confirm the manual contents before download.
--- Page 1 ---
CEBM014001
Shop
Manual
DUMP TRUCK
SERIAL NUMBERS A30255 thru A30291
--- Page 3 ---
TRUCK COMPONENTS AND SPECIFICATIONS
Truck And Engine Operator's Cab
The 930E Dump Truck is an off-highway, rear dump The operator cab has been engineered for operator
truck with AC Electric Drive. The gross vehicle weight comfort and to allow for efficient and safe operation
is 1,100,000 lbs. (498 960 kg). The engine is a of the truck. The cab provides wide visibility, with an
Komatsu SSDA16V160 rated @ 2700 HP (2014 kW). integral 4-post ROPS/FOPS structure, and an
advanced analog operator environment. It includes a
Alternator (GE-GTA34) tinted safety-glass windshield and power-operated
side windows, a deluxe interior with a fully adjustable
The diesel engine drives an in-line alternator at
seat with lumbar support, a fully adjustable/tilt steer-
engine speed. The alternator produces AC current
ing wheel, controls mounted within easy reach of the
which is rectified to DC within the main control cabi-
operator, and an analog instrument panel which pro-
net. The rectified DC power is converted back to AC
vides the operator with all instruments and gauges
by groups of devices called "inverters", also within
which are necessary to control and/or monitor the
the main control cabinet. Each inverter consists of six
truck's operating systems.
"phase modules" under the control of a "gate drive
unit" (GDU). The GDU controls the operation of each
phase module. Power Steering
Each phase module contains an air-cooled solid- The truck is equipped with a full time power steering
state switch referred to as a "gate turn-off thyristor" system which provides positive steering control with
(GTO). The GTO cycles on and off at varying fre- minimum operator effort. The system includes nitro-
quencies to create an AC power signal from the DC gen-charged accumulators which automatically pro-
supply. vide emergency power if the steering hydraulic
The AC power signal produced by each inverter is a pressure is reduced below an established minimum.
variable-voltage, variable-frequency signal (VVVF).
Frequency and voltage are changed to suit the oper- Dynamic Retarding
ating conditions.
The dynamic retarding is used to slow the truck dur-
ing normal operation or control speed coming down a
AC Induction Traction Motorized Wheels grade. The dynamic retarding ability of the electric
The alternator output supplies electrical energy to the system is controlled by the operator through the acti-
two wheel motors attached to the rear axle housing. vation of the retarder pedal (or by operating a lever
The motorized wheels use three-phase AC induction on the steering wheel) in the operators cab and by
motors with full-wave AC power. setting the RSC (Retarder Speed Control). Dynamic
The two wheel motors convert electrical energy back Retarding is automatically activated, if the truck
to mechanical energy through built-in gear trains speed goes to a preset overspeed setting.
within the wheel motor assembly. The direction of the
wheel motors is controlled by a forward or reverse Brake System
hand selector switch located on the center console.
Service brakes at each wheel are oil-cooled multiple
disc brakes applied by an all-hydraulic actuation sys-
Blower tem. Depressing the brake pedal actuates both front
Both the inverters and the wheel motors produce and rear brakes, after first applying the retarder. All
heat while in operation and must be cooled. Cooling wheel brakes will be applied automatically, if system
air is provided by a separate AC drive blower using pressure decreases below a preset minimum.
rectified DC as its power source. Cooling air flow vol-
ume is modulated based on thermal requirements. The parking brake is a dry disc type, mounted
inboard on each rear wheel motor, and is spring-
Suspension applied/hydraulically-released with wheel speed
application protection (will not apply with truck mov-
HYDRAIR®II suspension cylinders located at each
ing).
wheel provide a smooth and comfortable ride for the
operator and dampens shock loads to the chassis
during loading and operation.
A02054 09/03 Major Component Description A2-1
--- Page 4 ---
In The Operator’s Cab - Before Starting The OPERATING THE MACHINE
Engine
Starting The Engine
• DO NOT leave tools or spare parts lying around
or allow trash to accumulate in the cab of the • Never attempt to start the machine by shorting
truck. Keep all unauthorized reading material out across the starter terminals. This may cause fire,
of the truck cab. or serious injury or death to anyone in machine’s
path.
• Keep the cab floor, controls, steps, and handrails
free of oil, grease, snow, and excess dirt. • Never start the engine if a warning tag has been
attached to the controls.
• Check the seat belt, buckle and hardware for
damage or wear. Replace any worn or damaged • When starting the engine, sound the horn as an
parts. Always use the seat belts when operating alert.
a machine.
• Start and operate the machine only while seated
• Read and understand the contents of the in the operator’s seat.
Operation & Maintenance manual. Read safety
and operating instructions with special attention. • DO NOT allow any unauthorized persons in the
Become thoroughly acquainted with all gauges, operator's compartment or any other place on
the machine.
instruments and controls before attempting
operation of the truck.
• Read and understand the WARNING and
CAUTION decals in the operator's cab.
• Ensure the steering wheel, horn, controls and Truck Operation - General
pedals are free of any oil, grease or mud. • Wear seat belts at all times.
• Check operation of the windshield wiper, • Only authorized persons are allowed to ride in
condition of wiper blades, and check the washer the truck. Passengers must be in the cab and
fluid reservoir level. belted in the passenger seat.
• Be familiar with all steering and brake system • DO NOT allow anyone to ride on the decks or on
controls, warning devices, road speeds and the steps of the truck.
loading capabilities, before operating the truck.
• DO NOT allow anyone to get on or off the truck
while it is in motion.
• DO NOT move the truck in or out of a building
without a signal person present.
• Know and obey hand signal communications
between the operator and spotter. When other
machines and personnel are present, the
operator should move in and out of buildings,
loading areas and through traffic, under the
direction of a signal person. Courtesy at all times
is a safety precaution!
• Immediately report any adverse conditions on
haul road, pit or dump area that may cause an
operating hazard.
A03017 03/05 General Safety and Operating Instructions A3-7
--- Page 5 ---
SPECIAL PRECAUTIONS FOR WORKING ON A 930E TRUCK
Preliminary Procedures before Welding or Per- 3. After the engine cools, turn the key switch coun-
forming Maintenance terclockwise to OFF for normal engine shutdon.
Prior to welding and/or repairing a 930E dump truck, If the engine does not shutdown with the key
maintenance personnel should attempt to notify a switch, use the engine shutdown switch on the
Komatsu service representative. Only qualified per- center console. Pull the switch up until the
sonnel, specifically trained for servicing the A-C drive engine stops. Push the switch back down to
system, should perform this service. allow future engine operation.
4. With the key switch OFF, and the engine
If it is necessary to perform welding or repair to the stopped, wait at least 90 seconds. Ensure the
truck without the field engineer present, the following steering circuit is completely bled down by turn-
procedures should be followed to ensure that the ing the steering wheel back and forth several
truck is safe for maintenance personnel to work on times. No front wheel movement will occur
and to reduce the chance for damage to equipment. when hydraulic pressure is relieved. If the vehi-
cle continues to steer after shutdown, notify
maintenance personnel.
5. Verify that all the link voltage lights are off (one
Anytime the engine is operating: on back wall of operator cab, and two on deck
control cabinets). Notify maintenance personnel
• DO NOT open any of the cabinet doors or if any light remains illuminated longer than five
remove any covers. minutes after engine shutdown.
• DO NOT use any of the power cables for hand 6. Close and lock all windows, remove the key
holds or foot steps. from the key switch, and lock the cab to prevent
• DO NOT touch the retarding grid elements. possible unauthorized truck operation. Dis-
mount the truck properly. Place wheel chocks
around the wheels.
Engine Shutdown Procedure before Welding or
Performing Maintenance
Before opening any cabinets or touching a grid
element or a power cable, the engine must be Normal operation of the drive system at shutdown
shutdown and the red drive system warning should leave the system safe to maintain. However,
lights must not be illuminated. in the event of a system failure, performing the fol-
lowing procedure prior to any maintenance activities
will ensure that no hazardous voltages are present in
Normal Engine Shutdown Procedure the A-C drive system.
1. Stop the truck out of the way of other traffic on a 1. Before shutting down the engine, verify the sta-
level surface (dry, if possible) and free of over- tus of all the drive system warning lights on the
head power lines or other obstructions (in case overhead display panel. Use the lamp test
the dump body should need to be raised). switch to verify that all lamps are functioning
a. Reduce engine speed to idle. Allow the properly.
engine to cool gradually by running at low If any of the red drive system warning lights
idle for approximately 5 minutes. remain on, DO NOT attempt to open any cabi-
b. Place the selector switch in NEUTRAL. nets, disconnect any cables, or reach inside the
retarder grid cabinet without a trained drive sys-
c. Apply the parking brake. Be sure the parking
tem technician present - even if engine is off.
brake applied indicator light in the overhead
Only qualified personnel, specifically trained for
display panel is illuminated.
servicing the A-C drive system, should perform
2. Turn the rest switch to the ON position to put this service.
the A-C drive system in “rest” mode of opera-
2. If all red drive system warning lights are off, fol-
tion. Be sure the “rest” indicator light in the over-
low the “Normal Engine Shutdown Procedure”.
head panel is illuminated.
A03017 03/05 General Safety and Operating Instructions A3-17
--- Page 6 ---
DYNAMIC RETARDING OPERATION
Dynamic retarding is a braking torque (not a brake) c. For long downhill hauls, the lever may be
produced through electrical generation by the wheel positioned to provide a desired retarding
motors when the truck motion (momentum) is the effort. It will remain where it is positioned.
propelling force. For normal truck operation, dynamic NOTE: The retard control lever must be rotated back
retarding should be used to slow and control the to the OFF position before the truck will resume the
speed of the truck. “propel” mode of operation.
Dynamic retarding is available in FORWARD/ The lever and foot-operated retarder/service brake
REVERSE at all truck speeds above 0 mph/kph; pedal can be used simultaneously or independently.
however, as the truck speed slows below 3 mph (4.8 The PSC will determine which device is requesting
kph), the available retarding force may not be effec- the most retarding effort and apply that amount.
tive. Use the service brakes to bring the truck to a
complete stop.
Dynamic retarding will not hold a stationary truck on Dynamic Retarder/Service Brake Pedal
an incline; use the parking brake for this purpose.
The dynamic retarder/service brake pedal is a single,
Dynamic retarding is available in NEUTRAL only foot-operated pedal which controls both retarding
when truck speed is above 3 mph (4.8 kph). and service brake functions. The first portion of pedal
When dynamic retarding is active, the engine rpm will travel commands retarding effort through a rotary
automatically go to an advance rpm retard speed set- potentiometer. The second portion of pedal travel
ting (usually 900 - 1000 rpm*). modulates service brake pressure directly through a
hydraulic valve. Thus, the operator must first apply,
NOTE: The exact engine speed in retarding may vary and maintain, full dynamic retarding in order to apply
due to the temperature of certain components; this is the service brakes. Releasing the pedal returns the
controlled by the Propulsion System Controller brake and retarder to the OFF position.
(PSC).
When the pedal is partially depressed, dynamic
Dynamic retarding will be applied automatically if the retarding is actuated. As the pedal is further
speed of the truck reaches the maximum truck speed depressed to where dynamic retarding is fully
of 40 mph (64 kph). Any application of the dynamic applied, the service brakes (while maintaining full
retarding system (automatic, retarder lever, or foot retarding) are then actuated through a hydraulic
pedal) will cause an indicator light to illuminate in the valve, which modulates pressure to the service
overhead display panel. brakes. Completely depressing the pedal causes full
application of both dynamic retarding and the service
brakes. An indicator light in the overhead panel will
Dynamic Retarder Control Lever illuminate, and an increase in pedal resistance, will
be felt when the service brakes are applied.
The dynamic retarder control lever mounted on the
right side of the steering column can be used to mod- Use dynamic retarding (lever or foot-operated pedal),
ulate retarding effort. The lever will command the full during normal truck operation, to slow and control the
range of retarding and will remain at a fixed position speed of the truck. Apply the service brakes only
when released. when dynamic retarding requires additional braking
force to slow the truck speed quickly, or when bring-
a. When the lever is rotated to full "up" (coun- ing the truck to a complete stop.
terclockwise) position, it is in the OFF (No
Retard) position.
b. When the lever is rotated to full "down"
(clockwise) position, it is in the full ON
(Retard) position.
A03017 03/05 General Safety and Operating Instructions A3-27
--- Page 7 ---
This caution decal is placed near the battery discon- A caution decal is also attached to the door of the
nect switches on the right side of the front bumper to rear hatch cover to alert personnel that hot exhaust
alert servicing technicians that before doing any air is present and may cause injury.
welding on the truck, always disconnect the battery
charging alternator lead wire and isolate electronic
control components before making welding repairs.
This caution decal is also placed around the retard-
ing grid cabinet.
In addition, always disconnect the positive and nega-
tive battery cables of the vehicle. Failure to do so
may seriously damage the battery and electrical
equipment.
Always fasten the welding machine ground (-) lead to
the piece being welded; grounding clamp must be
attached as near as possible to the weld area. These warning plates are mounted on all of the AC
Never allow welding current to pass through ball drive control housings and cabinets.
bearings, roller bearings, suspensions, or hydraulic
High voltage may be present, with or without, the
cylinders. Always avoid laying welding cables over or
engine running!
near the vehicle electrical harnesses. Welding volt-
age could be induced into the electrical harness and Only authorized personnel should access these cabi-
possibly cause damage to components. nets.
A high voltage danger plate is attached to the door of
the rear hatch cover. High voltage may be present!
Only authorized personnel should access this rear
housing.
A04039 Warnings and Cautions A4-5
--- Page 8 ---
SECTION A7
STORAGE AND IDLE MACHINE PREPARATION
INDEX
STORAGE AND IDLE MACHINE PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-3
Short Term Idle Periods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-3
PREPARATION FOR STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-4
REMOVAL FROM STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-5
RECONDITIONING AN IDLE VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-7
ENGINE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-10
After The Engine Has Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A7-11
ENGINE STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-12
Preparing Engine For Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-12
Temporary Storage (30 Days Or Less) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-12
Extended Storage (more Than 30 Days) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-12
RESTORING AN ENGINE AFTER EXTENDED STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-14
ELECTRIC DRIVE TRUCKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-15
Storage Instructions and Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-15
Placing Equipment Into Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-15
Storing A Truck That Is Operational . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-15
Storing A Truck That Is Not Operational . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-16
Storing A Major Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-16
Periodic Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-17
Placing Equipment Into Service After Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-17
When A Truck Is Operational . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-17
When A Truck Is Not Operational . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-17
For The First Hour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7-18
A07003 Storage Procedures A7-1
--- Page 9 ---
After The Engine Has Started
Any machine which is unsafe and/or not in top oper- 5. When satisfied that all discrepancies have been
ating condition should not be assigned to an operator corrected, the vehicle is ready for a road test.
for production use. This test should be done only by a capable and
experienced operator and should be accom-
1. Become thoroughly familiar with steering and plished in a large open area where plenty of
emergency controls. Test the steering in maneuvering room is available. Some of the
extreme right and left directions. If the steering road test items which should be covered will
system is not operating properly, shut engine include:
down immediately. Determine the steering sys-
tem problem and have repairs made before • Repeated test of braking efficiency at
resuming operation. progressively higher speeds. Start at slow
speeds. Don't take chances with higher speeds
2. Operate each of the brake circuits at least twice until the machine is determined to be completely
prior to operating and moving the machine. safe.
These circuits include individual activation of
the service brake and parking brake from the
operator's cab. 6. When all tests and checks have been made and
the vehicle is ready for work, it should be visu-
a. Activate each circuit individually with the
ally rechecked and fully serviced according to
engine running and with hydraulic circuit fully
Section P, Lubrication and Service.
charged.
b. If any application or release of any brake cir-
cuit does not appear proper or if sluggish- A few of the conditions (others may be found) which
ness is apparent on application or release, might be encountered after a machine has been
shut the engine down and notify mainte- exposed to the elements for a long period would
nance personnel. Do not operate machine include:
until brake circuit in question is fully opera-
• Increased corrosion and fungus growth on
tional.
electrical components in humid/tropical areas.
3. Check gauges, warning lights and instruments
before moving the machine to insure proper • Accelerated rust formation in humid climates.
system operation and proper gauge functioning. • Increased sand and dust infiltration in windy, dry
Give special attention to braking and steering dusty areas. (These conditions can approach
circuit warning lights. If warning lights come on, sand blasting effects.)
shut down the engine immediately and deter- • Deterioration of rubber products in extreme cold
mine the cause. areas. Cables, hoses, O- rings, seals and tires
4. Cycle hoist controls and steering several times may become weather checked and brittle.
to remove trapped air. Complete steering cycles • Animal or bird's nests in unsealed openings.
in both directions to verify steering response,
smoothness and reliability. Check seals and
lines for leaks.
A07003 Storage Procedures A7-11
--- Page 10 ---
SECTION B2
STRUCTURAL COMPONENTS
INDEX
STRUCTURAL COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2-3
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2-3
GRILLE, HOOD AND LADDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2-4
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2-4
DECKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2-5
RIGHT DECK AND COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2-5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2-6
LEFT DECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2-6
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2-6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2-6
CENTER DECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2-6
B02015 Structural Components B2-1
--- Page 11 ---
BODY PADS 5. Install the mounting hardware and torque to 65
ft.lbs. (88.1 N-m).
It is not necessary to remove the dump body to
replace body pads. Pads should be inspected 6. Remove blocks from frame and lower body
during scheduled maintenance inspections and onto the frame.
replaced if worn excessively.
Adjustment
1. Raise the unloaded dump body to a height suf-
1. Vehicle must be parked on a flat, level surface
ficient to allow access to all pads.
for inspection.
2. All pads, except the rear pad on each side,
should contact the frame with approximately
equal compression of the rubber.
3. A gap of approximately 0.075 in. (1.9 mm) is
Place blocks between the body and frame. required at each rear pad. This can be accom-
Secure blocks in place. plished by using one less shim at each rear
2. Remove hardware attaching pads to the dump pad.
body. Refer to Figure 3-4. 4. If pad contact appears to be unequal, repeat
3. Remove body pad and shims. Note number of the above procedure.
shims installed at each pad location. (The rear
pad on each side should have one less shim
! IMPORTANT !
than the other pads.)
Proper body pad to frame contact is required to
4. Install new pads with the same number of assure maximum pad life.
shims as removed in step 3.
FIGURE 3-4. BODY PAD INSTALLATION
1. Dump Body 3. Frame 5. Shim
2. Pad Mounting Hardware 4. Body Pad 6. Mounting Pad
B03017 08/03 Dump Body B3-5
--- Page 12 ---
LEFT SIDE FILL