PDF Shop Manual Komatsu 830E-1AC Dump Truck - 2 MB

This comprehensive shop manual is the ultimate guide for servicing and repairing the Komatsu 830E-1AC dump truck (serial numbers A30561 and up).

It contains detailed technical information, disassembly and assembly procedures, testing and adjusting instructions, and troubleshooting guides.

Professional technicians rely on this manual to perform accurate and efficient repairs, minimizing downtime for this massive machine.

It is the definitive resource for maintaining your Komatsu haul truck.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
CEBM027402


Shop
Manual


             830E-1AC
             DUMP TRUCK

             SERIAL NUMBERS                       830E-1AC A40851 – A40938
                                                           A40995
             ENGINE                               16V160

 This material is proprietary to Komatsu America Corp. and is not to be reproduced, used, or disclosed except in
 accordance with written authorization from Komatsu America Corp.

 It is our policy to improve our products whenever it is possible and practical to do so. We reserve the right to
 make changes or improvements at any time without incurring any obligation to install such changes on products
 sold previously.

 Due to this continuous program of research and development, revisions may be made to this publication. It is
 recommended that customers contact their distributor for information on the latest revision.


                                                                              Copyright March 2022
                                                                              Printed in U.S.A.
                                                                              Komatsu America Corp.

--- Page 3 ---
SECTION A3
                       GENERAL SAFETY AND OPERATING INSTRUCTIONS
                                         INDEX
GENERAL SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-6

           Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-6

           Truck Safety Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-6

           Clothing And Personal Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-6

           Unauthorized Modification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-6

           Leaving The Operator’s Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-6

           Mounting And Dismounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-7

           Fire Extinguishers And First Aid Kits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-7

           Precautions For High Temperature Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-7

           Asbestos Dust Hazard Prevention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-7

           Fire Prevention For Fuel And Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-8

           ROPS Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-8

           Preventing Injury From Work Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-8

           Precautions For Optional Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-8

           Precautions When Starting The Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-8

       PRECAUTIONS FOR TRUCK OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-9

           Safety Is Thinking Ahead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-9

           Safety At The Worksite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-9

           Fire Prevention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-9

           Preparing For Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-9

           Ventilation For Enclosed Areas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-9

           Mirrors, Windows, And Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-10

           In The Operator’s Cab - Before Starting The Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-10

       OPERATING THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-10

           Starting The Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-10

           Truck Operation - General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3-10

           Traveling In The Truck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A3-11

           Precautions When Traveling In Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A3-11


A03052 2/22                                        General Safety and Operating Instructions                                                                 A3-1

--- Page 4 ---
Jump Starting With Jumper Cables                           Jump Starting With Receptacles
 • Always wear safety glasses or goggles when               • Always wear safety glasses or goggles when
   starting the machine with jumper cables.                   starting the machine with jumper cables.
 • While jump starting with another machine, DO             • While jump starting with another machine, DO
   NOT allow the two machines to touch.                       NOT allow the two machines to touch.
 • Ensure the parking brake is applied on both              • Ensure the parking brake is applied on both
   machines. The engine on the good machine is to             machines. The engine on the good machine is to
   be operating.                                              be operating.
 • Ensure the size of the jumper cables and clips           • Inspect the cables and connectors for any
   are suitable for the battery size. Inspect the             damage or corrosion.
   cables and clips for any damage or corrosion.
                                                            • Ensure the key switch and master battery
 • Ensure the key switch and master battery                   disconnect switch (3, Figure 3-2) on the disabled
   disconnect switch (3, Figure 3-2) on the disabled          machine is in the OFF position.
   machine is in the OFF position.
                                                            • Connect the jumper cable to the receptacle on
 • Connect the batteries in parallel: positive to             the good machine to the receptacle on the
   positive and negative to negative.                         disabled machine.
 • Connect the positive (24VDC +) cable from the            • Allow time for the batteries to charge.
   good machine to the (24VDC +) on the disabled
                                                           NOTE: The batteries will charge even with the
   machine first.
                                                           master battery disconnect switch is in the OFF
 • Then connect the ground cable from the negative         position.
   (-) battery terminal on the good machine to the
   frame of the disabled machine, as far away as            • If starting with a jumper cable, perform the
   possible from the batteries. This will prevent a           operation with two people. One person in the cab
   spark from possibly starting a battery fire.               of the disabled machine, the other person
                                                              working with the jumper cables.
 • Move the master battery disconnect switch (3,
   Figure 3-2) to the ON position. Allow time for the       • If the batteries are low, DO NOT attempt starting
   batteries to charge.                                       the machine with only one set of jumper cables
                                                              installed. Install the second set of jumper cables
 • If starting with a jumper cable, perform the               in the same way as already described.
   operation with two people. One person in the cab
   of the disabled machine, the other person                • Turn the master battery disconnect switch (3,
   working with the jumper cables.                            Figure 3-2) to the ON position and attempt
                                                              starting.
 • If the batteries are low, DO NOT attempt starting
   the machine with only one set of jumper cables           • For jumper cable removal, disconnect the cables
   installed. Install the second set of jumper cables         from each machine.
   in the same way as already described.                    • If any tool touches between the positive (+)
 • Attempt starting the disabled machine.                     terminal and the chassis, it will cause sparks.
                                                              Always use caution when using tools near the
 • For jumper cable                                           batteries.
   removal,
   disconnect         the
   ground or negative
   (-) cable first, then
   the (24VDC +)
   cable last.


 • If any tool touches between the positive (+)
   terminal and the chassis, it will cause sparks.
   Always use caution when using tools near the
   batteries.


A03052 2/22                        General Safety and Operating Instructions                             A3-15

--- Page 5 ---
SPECIAL PRECAUTIONS FOR WORKING ON AN 830E-1AC TRUCK
Preliminary Procedures before Welding or Per-                Engine Shutdown Procedure before Welding or
forming Maintenance                                          Performing Maintenance
Prior to welding and/or repairing an 830E-1AC dump           Normal operation of the drive system at shutdown
truck, maintenance personnel must attempt to notify          leaves the system safe to maintain. However, in the
a Komatsu service representative. Only qualified per-        event of a system failure, performing the following
sonnel, specifically trained for servicing the AC drive      procedure prior to any maintenance activities will
system, must perform this service.                           ensure that no hazardous voltages are present in the
                                                             AC drive system.
If it is necessary to perform welding or repair to the
truck without the field engineer present, the following         1. Before shutting down the engine, verify the sta-
procedures must be followed to ensure that the truck               tus of all the drive system warning lights on the
is safe for maintenance personnel to work on and to                overhead display panel. Use the lamp test
reduce the chance for damage to equipment.                         switch to verify that all lamps are functioning
                                                                   properly.
                                                                   If any of the red drive system warning lights
                                                                   remain on, DO NOT attempt to open any cabi-
                                                                   nets, disconnect any cables, or reach inside the
Anytime the engine is operating:
                                                                   retarder grid cabinet without a trained drive sys-
•   DO NOT open any of the cabinet doors or                        tem technician present - even if engine is off.
    remove any covers.                                            Only qualified personnel, specifically trained for
•   DO NOT use any of the power cables for hand                   servicing the AC drive system, must perform
    holds or foot steps.                                          this service.
•   DO NOT touch the retarding grid elements.                   2. If all red drive system warning lights are off, fol-
                                                                   low all of the instructions for “Parking The
                                                                   Machine.”
                                                                3. After the engine has been off for at least five
                                                                   minutes, inspect the link voltage lights on the
Before opening any cabinets or touching a grid                     exterior of the main control cabinet and rear of
element or a power cable, the engine must be                       the center console. If all lights are off, the retard
shutdown and the red drive system warning                          grids, wheel motors, alternator, and related
lights must not be illuminated.                                    power cables are safe to work on.
                                                                4. Locate the GF cut-out switch in the front access
                                                                   panel on the left side of the main control cabi-
                                                                   net. Place the switch in the CUTOUT position.
                                                                   This will prevent the alternator from re-energiz-
                                                                   ing and creating system voltage until the switch
                                                                   is returned to the previous position.
                                                                5. Ensure both battery disconnect switches are in
                                                                   the OFF position. Verify that the battery discon-
                                                                   nects are functioning.
                                                                6. Before doing any welding on the truck, always
                                                                   disconnect the battery charging alternator lead
                                                                   wire.


A03052 2/22                          General Safety and Operating Instructions                                   A3-29

--- Page 6 ---
6. Inspect air conditioner belts for correct tension,        13. Move around the dual tires, and check to see
     obvious wear, and tracking. Inspect fan guard                 that all lugs/wedges are in place and tight.
     security and condition. When leaving this point,              Inspect latches on the wheel cover to be sure
     ensure the service light is off, if used.                     they are properly latched. Inspect the wheel for
  7. Move outboard of the front wheel. Inspect                     any oil that would indicate brake leakage or
     attaching lugs/wedges to ensure all are tight                 wheel motor leakage.
     and complete. Inspect the tires for cuts, dam-                Check the dual tires (18) for cuts, damage or
     age or bubbles. Check tire inflation pressure.                bubbles. Verify that inflation appears to be cor-
     Check sight glass for front wheel oil level.                  rect. If the truck has been operating on a flat
  8. Move behind the front wheel and inspect the                   tire, the tire must be cool before moving the
     steering cylinder. Check for proper greasing                  truck inside a building. Check for any rocks that
     and inspect the mounting hardware to ensure it                might be lodged between the dual tires. Inspect
     is all in place. Inspect all steering linkage joints          the rock ejector condition and straightness so
     (10, Figure 3-16) for proper greasing. Inspect                that it can not damage a tire.
     the suspension mounting hardware to ensure it
                                                               14. Inspect the left rear suspension (19) for damage
     is all in place. Ensure the suspension protective
                                                                   and for correct rod extension. Check for leaks.
     boot is in good condition. Inspect the hub and
                                                                   Ensure that the covers over the chrome piston
     brakes for any unusual conditions. Check the
                                                                   rod are in good condition. Inspect for proper
     entire area for leaks.
                                                                   greasing.
  9. Inspect the sight glass on hydraulic tank (21).
     With the engine stopped and body down,                    15. Open the rear hatch cover (20), turn on the work
     hydraulic fluid must be visible in the upper sight            light if necessary. Inspect for leaks around
     glass.                                                        wheel motor mounting to rear housing, and also
                                                                   brake hoses and fittings. Ensure that covers on
 10. Verify all hydraulic tank shut off valves are                 wheel motor sump are in place, and that there
     locked in their fully open positions.                         are no rags or tools left behind. Inspect condi-
 11. Move around the hydraulic tank and in front of                tion of hatch cover gasket, report any bad gas-
     the rear dual tires. Inspect hoist cylinder (15) for          ket to maintenance. Turn off work light if used,
     any damage and leaks. Inspect both upper and                  close and latch hatch.
     lower hoist cylinder pins for integrity and for           16. While standing in front of the rear hatch, look up
     proper greasing.                                              to see that rear lights are in good condition,
 12. Before leaving this position, look under the                  along with the back-up horns. Look up at the
     lower edge of the chassis to ensure the flexible              panhard rod to see that it is getting proper
     duct that carries the air from the blower to the              greasing. Also look at both body hinge pins for
     final drive housing is in good condition with no              greasing and any abnormal condition. Check
     holes or breakage. Also, look up at the main                  hoist limit switch and clear any mud/debris from
     hydraulic pumps (22) to see that there is no                  contacts.
     leakage or any other unusual condition with the           17. Perform the same inspection on the right rear
     pumps or the pump drive shafts.                               suspension (19) as done on the left.


A03052 2/22                           General Safety and Operating Instructions                               A3-43

--- Page 7 ---
Parking Brake Test                                            Retard System Test:
  1. Place the directional control lever in the PARK             1. Place the directional control lever in the PARK
     position.                                                      position.
  2. Press the brake test switch and wait for the                2. Press the brake test switch and wait for the
     brake check light to be on solid.                              brake check light to be on solid.
  3. The DID panel will display:                                 3. The DID panel will display:
    Parking Brake or Retard Test READY                             Parking Brake or Retard Test READY
    Press Accel or Retard Pedal to Start                           Press Accel or Retard Pedal to Start

  4. Fully depress the accelerator pedal. The drive              4. Fully depress the retard pedal. The drive sys-
     system controller will enter propel mode and                   tem controller will ramp up the engine speed,
     generate torque up to the park brake limit.                    close CM1, close CM2, close CM3 close CM4,
  5. The DID panel will display:                                    turn on the choppers, and test the retarding sys-
                                                                    tem. The system will verify current flow through
    Park Brake Test ACTIVE                                          each grid leg and the grid blower motor.
    Check Truck Movement when Light Flashes
                                                                 5. The DID panel will display the current status of
                                                                    the test.
  6. Once the torque has reached the limit for the
     parking brake test, the brake check light will                Retard System Test ACTIVE
     begin to flash. This is the indication for the oper-          CM1 CM2 CM3 CM4 CHOP
     ator to make a determination as to the status of              (Elements are added as the test progresses.)
     the parking brake system.
                                                                 6. Upon successful completion of the test, the light
   • If the truck did not move:
                                                                    will flash for 10 seconds indicating a successful
     The park brake system passed the test.
                                                                    test. The DID panel will display:
   • If the truck moved during the test:
     The park brake test has failed. Release the                   Retard System Test PASSED
     accelerator pedal. If the truck starts to roll, apply         or
     the service brakes to hold the truck stationary.
     Notify maintenance personnel immediately.                     Retard System Test FAILED or Incomplete
                                                              NOTE: If the brake check light never flashes, but
                                                              turns off, the test has failed.


If the truck moves at all during the parking brake
test, immediately release the accelerator pedal to
avoid serious damage to the parking brake.                    If the truck fails the retard system test, notify
                                                              maintenance personnel immediately. Do not
                                                              resume operation unless the truck passes all
                                                              brake tests.


If the truck fails the parking brake test, notify                7. When the operator releases the retard pedal,
maintenance personnel immediately. Do not                           the test will stop and the brake check light will
resume operation unless the truck passes all                        turn off.
brake tests.                                                     8. If the retard system failed the test, notify main-
                                                                    tenance personnel immediately. Do not resume
                                                                    operation unless the truck passes all brake
  7. When the operator releases the accelerator                     tests.
     pedal, torque will be reduced, the test will stop
     and the brake check light will turn off.


A03052 2/22                           General Safety and Operating Instructions                                A3-57

--- Page 8 ---
8. The parking brakes must be released before                9. Ensure the operator in the towing vehicle has 2-
     towing. To release the parking brake, follow the             way radio communications with the driver in the
     steps below to install a special wiring harness to           disabled truck.
     release the parking brakes.
                                                             10. When ready to tow the disabled truck, remove
    a. Ensure switch (1, Figure 3-26) is in the OFF              blocking from the wheels.
       position.
                                                             11. The operator in the disabled truck should now
    b. Connect one lead of the special wiring                    move switch (1, Figure 3-26) to the ON position.
       harness to the 24VDC bus bar terminal on                  This will release the parking brakes.
       the side wall in the auxiliary control cabinet
                                                             12. Tow the disabled truck. Sudden movement may
       for the 24V supply.
                                                                 cause tow bar failure. Smooth, gradual truck
    c. Disconnect the truck wiring harness from                  movement is preferred. Do not tow the truck
       parking brake solenoid (2, Figure 3-27).                  any faster than 8 kph (5 mph).
       Connect special wiring harness (3, Figure
                                                             13. Minimize the tow angle at all times. Never
       Figure 3-26) to the parking brake solenoid.
                                                                 exceed 30 degrees. The towed truck must be
       Attach the short lead (2) to ground.
                                                                 steered in the direction of the tow bar.
    d. WIth the window lowered, place the end of
                                                             14. When the desired location has been reached,
       the special wiring harness inside the cab so
                                                                 the operator in the towed vehicle is to apply the
       the operator can control the parking brake
                                                                 service brakes, then turn switch (1) to the OFF
       with switch (1).
                                                                 position. This will apply the parking brakes.
                                                             15. Block the wheels on the towing vehicle and the
                                                                 disabled truck to prevent roll-away.
                                                             16. Shut down the engine in the towing vehicle.
                                                                 Disconnect the hydraulic hoses.
                                                             17. Disconnect special wiring harness (3) from the
                                                                 truck. Connect the truck wiring harness back to
                                                                 the parking brake solenoid.
                                                             18. Disconnect the tow bar.


         FIGURE 3-27. BRAKE CABINET
  1. Brake Manifold            2. Park Brake Solenoid


A03052 2/22                         General Safety and Operating Instructions                              A3-71

--- Page 9 ---
A caution decal is also attached to the door of the
rear hatch cover to alert personnel that hot exhaust
air is present and may cause injury.
This caution decal is also placed around the retard-
ing grid cabinet.


This decal is placed on both front wheel hubs to warn
about hot oil inside the wheel hubs. Remove the oil
level plug carefully to avoid injury.


The lubrication chart is mounted on the right hand
side of the radiator grille structure. Refer to Section P,
Lubrication and Service, in this manual for more
complete lubrication instructions.


A04066 2/22                                      Warnings and Cautions   A4-13

--- Page 10 ---
STORAGE AND IDLE MACHINE PREPARATION
There may be periods when it is necessary for a                  1. Keep the vehicle fully serviced.
machine to be idle for an extended period of time.               2. On a weekly schedule, perform a visual check
Properly prepared, a stored machine may promptly                    of the vehicle, start and run the engine until both
and safely be put back into operational service.                    the engine and transmission are up to operating
Improper preparation, or complete lack of prepara-                  temperature. Move the vehicle around the yard
tion, can make the job of getting the vehicle back to               for a few minutes to insure that all internal gears
operating status difficult.                                         and bearings are freshly lubricated.
The following information outlines the essential                 3. Operate all hydraulic functions through com-
proper steps for preparing a unit for extended stor-                plete range to insure that cylinder rams and all
age, and the necessary steps to bring it back to oper-              seals are fully lubricated.
ational status. Additional information is given to help
restore those machines which were not put into stor-
age, merely shut down and left idle for a long period
of time.
Much of this material is of a general nature since the
environment, where the machine has been standing
idle, will play a big part in its overall condition. Hot,
humid climate will affect vehicle components much
differently than the dry desert atmosphere or a cold
arctic environment. These climatic aspects must be
considered, and appropriate actions taken when
restoring a long term idle vehicle.
These instructions are not intended to be all inclu-
sive, but are furnished to provide the minimum guide
lines. The final aim should always be to provide the             4. Check and operate all systems.
operator with a safe, fully productive vehicle, that he          5. Once a month, perform the 10 hour service
can rely on.                                                        items shown in the Operation and Maintenance
                                                                    Manuals. Keep batteries properly serviced.

SHORT TERM IDLE PERIODS
There will be periods when a vehicle may be idle
from 30-60 days, but must be ready for use at all
times.
The most effective handling of this type situation is to
follow the procedure given below to prevent any
deterioration from beginning.


A07006                                            Storage Procedures                                             A7-3

--- Page 11 ---
TRANSMISSION PRESERVATION AND                                    5. Continue running the engine at 1500 rpm with
STORAGE                                                             the transmission in neutral until normal operat-
                                                                    ing temperature is reached.
Storage, New Transmission
(Prior to installation). New transmissions are tested
with preservative oil and drained prior to shipment.
The residual oil remaining in the transmission pro-
vides adequate protection to safely store the trans-          If the unit does not have a converter-out tempera-
mission for up to one year (stored inside the                 ture gage, do not stall the converter.
conditions of normal climate and with all shipping               6. If normal operating temperature is less than
plugs installed) without further treatment.                         225° F (107° C), shift the transmission to the
Preservation Methods. When the transmission is to                   highest forward range and stall the con-
be stored or remain inactive for an extended period                 verter.When the converter-out temperature
(one or more years), specific preservation methods                  reaches 225° F (107° C), stop the engine. Do
are recommended to prevent damage due to rust,                      not exceed 225° F (107° C).
corrosion, and organic growth in the oil. Preservation           7. As soon as the transmission is cool enough to
methods are presented for storage with and without                  touch, seal all openings and the breather with
transmission fluid.                                                 moisture-proof tape.
                                                                 8. Coat all exposed, unpainted surfaces with pre-
Storage, One Year -- Without Oil
                                                                    servative grease such as petrolatum (MIL-C-
  1. Drain the oil.                                                 11796, Class 2).
  2. Spray two ounces (60 milliliters) of VCI #10                9. If additional storage time is required, repeat
     through the fill tube.                                         steps (2) through (8) at yearly intervals; except,
  3. Seal all openings and the breather with mois-                  it is not necessary to drain the transmission
     ture-proof tape.                                               each year. Just add Motorstor and Biobor Jf (or
  4. Coat all exposed, unpainted surfaces with pre-                 equivalents).
     servative grease such as petroleum (MIL-C-
     11796, Class 2).
  5. If additional storage time is required, repeat           Restoring Transmission to Service
     steps (2), (3) and (4) at yearly intervals.                 1. Remove all tape from openings and the
                                                                    breather.
                                                                 2. Wash off all external grease with mineral spirits.
Storage, One Year With Oil (normally in a vehicle                3. If the transmission is new, drain the residual
chassis)                                                            preservative oil. Refill the transmission to the
  1. Drain the oil and replace the oil filter element(s).           proper level with C-4 transmission fluid.
  2. Fill the transmission to operating level with a             4. If the transmission was prepared for storage
     mixture of one part VCI #10 (or equivalent) to                 without oil, drain the residual oil and replace the
     30 parts C-3 transmission fluid. Add 1/4 tea-                  oil filter elements. Refill the transmission to the
     spoon of Biobor JF (or equivalent) for each 3                  proper level with C-4 transmission fluid.
     gallons (11 liters) of fluid in the system.                 5. If the transmission was prepared for storage
NOTE: When calculating the amount of Biobor JF                      with oil, it is not necessary to drain and refill the

View the complete manual on HeyDownloads →