PDF Shop Manual KCM 70Z7B Wheel Loader Cummins QSB6.7 Engine - 1 MB

This shop manual provides comprehensive service information for the KCM 70Z7B wheel loader, with a specific focus on the Cummins QSB6.7 engine.

It is an essential tool for technicians performing advanced diagnostics, repairs, and overhauls.

Inside, you'll find detailed procedures, specifications, and troubleshooting flowcharts.

Keep your heavy equipment in optimal condition with this factory-level repair guide.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
93208-00870


                                                                     70Z7B
                                                                                                                                              May 2017


                                                                                                                                          Volume 2


                                                                     SHOP MANUAL
                                                                                                      SHOP MANUAL

                                                                                                      WHEEL LOADER


                                                                     Disassembly & Reassembly Vol.2
                                                                                                      70Z7B

                                                                                                      Disassembly & Reassembly

                                                                      93208-00870


                                                                                                      Powered by CUMMINS QSB6.7 ENGINE

                                                                                                      Serial No. 70C6-5001 and up
©2017 KCM Corporation. All rights reserved.   Printed in Japan (K)
                                                    (アメリカ用)

--- Page 3 ---
SECTION 4 TRAVEL SYSTEM
                 Group 1 Tire

(Blank)


                  W4-1-1-6

--- Page 4 ---
SECTION 4 TRAVEL SYSTEM
                                                   Group 2 Drive Unit


                                                                   View A
                                                               7                               7
                      6
                 5

    a
                                                                                   8


                                                           8
                                                                                       c
                                                       A


                                  4
                                             WNEK50-04-02-005                                      WNEK50-04-02-007
                                                                   c-   Contact surface


                                                                                           4
  Installation
  1. Install all removed adapters to drive unit (4).
IMPORTANT: Check the direction to install guide (8).
  2. Apply molybdenum grease onto the contact surface
     (c) of guide (8). Install guide (8) to engine (7).

dCAUTION: Drive unit (4) weight: 500 kg (1110 lb)
  3. Install the shackles (2 used) to lifting brackets (a) (2
     places). Attach the nylon slings onto the shackles (2
     used). Hoist drive unit (4).
                                                                                                   b
dCAUTION:      Place a stable stand (b) under drive
 unit (4) in order not to fall down the engine (7)
                                                                                                   WNEK50-04-02-008
   assembly.
                                                                   b-   Stand
  4. Install drive unit (4) to engine (7) with spring
     washers (6) (12 used) and bolts (5) (12 used) by
     fitting drive unit (4) to guide (8).

     j : 17 mm

     m : 36±3.6 N·m (26.5±2.7 lbf·ft)


                                                           W4-2-1-4

--- Page 5 ---
SECTION 4 TRAVEL SYSTEM
                                                      Group 2 Drive Unit

  Installation of Oil Filter
  1. Apply oil onto O-rings (1) (2 used). Install O-rings
                                                                            5   1, 2
     (1) (2 used) to filter head (2). Install filter head (2) to
     duct plate (5) with socket bolts (3) (2 used) by using
     a hexalobular internal wrench.

      l : T40 (Hexalobular Internal Wrench)                             3

      m : 34 N·m (25 lbf·ft)


                                                                                           W4GB-03-02-010
IMPORTANT: Take care not to tighten oil filter (4) too
                                                                                2
   excessively in order not to deform.
  2. Apply oil onto the seal surface of oil filter (4).
     Tighten oil filter (4) to filter head (2) until it comes
     into contact with seal surface. Tighten oil filter (4) by
     1/3 to 1/2 turn by using a filter wrench after it has
     come into contact with seal surface.


                                                                                       4   W4GB-03-02-011


                                                             W4-2-2-6

--- Page 6 ---
SECTION 4 TRAVEL SYSTEM
                                                Group 2 Drive Unit

  5. Remove socket bolts (10) (10 used). Remove the oil       8. Remove stator shaft (12) from transmission case
     feeder housing (6) assembly and gasket (7) from             (13).
     transmission case (13). Remove O-rings (11) (10
     used) from socket bolts (10) (10 used).

     l : 8 mm                                                                                     13
IMPORTANT: Do not disassemble hydraulic pump (9).
  6. Remove hydraulic pump (9) from oil feeder housing                                                     12
     (6) by using a plastic hammer. Remove O-ring (8)
     from hydraulic pump (9).


          6              8, 9


                                                                                                       W4GB-03-02-044


                                            W4GB-03-02-040

  7. Push pressure plate (19) with the bolt (M6). Remove
     tab washer (22). Remove pressure plate (19), spring
     (20), and piston (21) from oil feeder housing (6).

                                22   21           6


           19


                           20               W4GB-03-02-043


                                                       W4-2-4-4

--- Page 7 ---
SECTION 4 TRAVEL SYSTEM
                                                   Group 2 Drive Unit

12. Remove piston rings (13) (6 used) from the clutch          14. Remove second speed clutch (K2) from transmission
    shafts (6 used).                                               case cover (1).

                                                                             K2
                                13
            13
   KR
                                         KV

  K4
                                              K2               1
                                                    1


       K1                                          K3


                          13                  W4GB-03-02-106                                            W4GB-03-02-084


13. Raise fast-speed forward clutch (K4) a little from         15. Remove third speed clutch (K3) from transmission
    transmission case cover (1) and hold it. Remove first          case cover (1).
    speed clutch (K1) from transmission case cover (1).
    Return fast-speed forward clutch (K4).

                    K4                                              1


                                                                                                        W4GB-03-02-085
                                                                                                K3

                                              W4GB-03-02-083
                     K1              1


                                                        W4-2-4-14

--- Page 8 ---
SECTION 4 TRAVEL SYSTEM
                                                   Group 2 Drive Unit

 29. Install special tool (b) (ZF No.: 5870 280 007) to the
     shaft part of slow-speed forward clutch (KV) and
     check that it turns. Check it for all clutches. If any
     abnormality is found, disassemble it again, trace it,
     and correct the cause.
                                 b


b-   Special Tool

                                               W4GB-03-02-119


 30. Install plate (4) and socket bolts (2) (35 used) to
     transmission case cover (1).

      l : 8 mm

      m : 46 N·m (34 lbf·ft)


             4

         2                                            1


                                               W4GB-03-02-120


                                                           W4-2-4-24

--- Page 9 ---
SECTION 4 TRAVEL SYSTEM
                                                    Group 2 Drive Unit

 15. In order to engage the spline of idler (24) and the
     gear teeth of inner clutch disc (15) with shaft (3),          dCAUTION:     Put heat-resisting gloves when
                                                                    installing the inner ring of taper roller bearing
     install idler (24) to shaft (3) by turning it right and
     left.                                                            (29).
                                                                    17. Heat the inner ring of taper roller bearing (29) to
                                                                        about +120 °C (248 °F). Install the inner ring of taper
                                                                        roller bearing (29) to shaft (3).


                                                                                                                    29
                                                        24


                                                          3
                                                                                                                    3

                                                W4GB-03-02-139


IMPORTANT: Install running disc (27) with the
   chamfered surface facing to the axial needle cage                                                             W4GB-03-02-142
   (26) side.
 16. Install axial washer (25), axial needle cage (26),
     running disc (27), and retaining ring (28) (only K1
     and K2) to idler (24).

                                                        27

                                                        26
                                                        25

                                                       24


                                                W4GB-03-02-141


fNOTE: When the parts have been installed correctly in
   step 16, the level difference of upper surface of running
   disc (27) and shaft (3) are the same. If running disc (27)
   is higher, check the engagement of idler (24) and inner
   clutch disc (15).


                                                             W4-2-4-34

--- Page 10 ---
SECTION 4 TRAVEL SYSTEM
                                                  Group 2 Drive Unit

  Disassembly of Fast-Speed Forward Clutch (K4)
IMPORTANT: Do not disassemble snap ring (7) and                     9. Compress coil spring (24) by using special tool (a)
   gear (6).                                                           (ZF No.: 5870 345 088). Remove snap ring (22) from
  1. Remove piston rings (2, 5) from shaft (3).                        disc carrier (29). Release coil spring (24). Remove
                                                                       coil spring (24) from disc carrier (29).
  2. Remove stud (4) from shaft (3). Remove taper roller
     bearings (1, 31) from shaft (3) by using the special                                           a
     tools (ZF No.: 5870 026 100 and 5873 001 057).
  3. Remove snap ring (30) from shaft (3). Remove disc
     carrier (29) from shaft (6) by using a puller.
  4. Remove running disc (15), axial needle cage (14),
     and axial washer (13) from idler (12).
  5. Remove idler (12) from shaft (3).
                                                                                                             29
  6. Remove needle cages (11) (2 used), axial washer
     (10), axial needle cage (9), and axial washer (8) from
     shaft (3).
  7. Remove snap ring (7) from shaft (3). Remove gear          a-    Special Tool
                                                                                                             W4GB-03-02-124
     (6) from shaft (3).
  8. Remove snap ring (16) from disc carrier (29).              10. Supply low-pressure air through the oil hole of disc
     Remove end shim (17), outer clutch discs (20) (4               carrier (29) and remove piston (26) from disc carrier
     used), inner clutch discs (19) (5 used), and disc (20)         (29).
     from disc carrier (29).


                                                                                                             W4GB-03-02-125


                                                                11. Remove O-rings (27, 28) from piston (24).


                                                         W4-2-4-44

--- Page 11 ---
SECTION 4 TRAVEL SYSTEM
                                                   Group 2 Drive Unit

     Removal and Installation of Duct Plate

                                                              1                  2               3


     9


                                               8                                     1   7      6     4, 5
                                                                                                              W4GB-03-02-012


1-       Nut (14 Used)           4-   Switch                 7-   Spring                     10- *Transmission Case Cover
2-       Duct Plate              5-   O-Ring                 8-   Gasket
3-       Socket Bolt (36 Used)   6-   Piston                 9-   Safety Valve


fNOTE: As for the item with mark *, refer to W4-2-4-1.


                                                         W4-2-5-4

--- Page 12 ---
SECTION 4 TRAVEL SYSTEM
              Group 2 Drive Unit

(Blank)


                  W4-2-5-14

--- Page 13 ---
SECTION 4 TRAVEL SYSTEM
              Group 2 Drive Unit

(Blank)


                  W4-2-6-10

--- Page 14 ---
SECTION 4 TRAVEL SYSTEM
                                                          Group 3 Axle


                                                                                                        1


                                                              4


                                                              5


                                                                              3
                                               WNEK50-04-03-001                                                 WNEK50-03-13-001
                                                                                          2


 12. Set the machine position (lift arm raise) for                  17. Set the machine position (lift arm raise) for
     inspection and maintenance. (Refer to W1-5-1.)                     inspection and maintenance. (Refer to W1-5-1.)
 13. Connect hose (5) with clamp (4).                               18. Install front cover (1). (Refer to W3-22-1.)

     j : 7 mm

     m : 3 N·m (2.2 lbf·ft)
 14. Bleed air from the brake (axle). (Refer to W1-4-1.)
 15. Set the machine position (lift arm lower) for
     inspection and maintenance. (Refer to W1-5-1.)
 16. Install front tires (2) (2 used) to front axle (3). (Refer
     to W4-1-1.)
IMPORTANT: Check the hydraulic oil level. Start the
   engine and check for any oil leaks.


                                                             W4-3-1-10

--- Page 15 ---
SECTION 4 TRAVEL SYSTEM
                                                        Group 3 Axle

                                                        3
                                                                              1
                                              2

                                        1


                5
                      7

                                6

                                        5


                                                                 4

                                                                                                                    WNEK50-04-03-014


                                                                                          b
IMPORTANT: Check the direction to install dust seal
   (5) and bushing (7).                                              a
                                                                                  a
IMPORTANT: Install bushing (7) with slit (b) up.
                                                                                                            a
  9. Install bushing (7) and dust seals (5) (2 used) to
     support (6).

dCAUTION: Support (6) weight: 65 kg (145 lb)
 10. Apply grease onto the inner circumference of
     bushing (7). Attach nylon slings onto support (6).
     Hoist steering support (6). Install support (6) to rear
     axle (4).
                                                                          5           7             6           5         4
 11. Secure support (6) to rear axle (4) by using wires.                                                            WNEK50-04-03-019
                                                                     a-    Direction to Install
 12. Install block (3) to rear axle (4) with bolt, washer (2).       b-    Slit

     j : 17 mm

     m : 50 N·m (37 lbf·ft)
                                                                         13. Connect the both ends of pipes (1) (2 used).

                                                                              j : 22 mm

                                                                              m : 39 N·m (29 lbf·ft)


                                                            W4-3-2-10

--- Page 16 ---
SECTION 4 TRAVEL SYSTEM
                                          Group 3 Axle

 Planetary Carrier Assembly (70)


                                                              WNDB-04-03-005


                                            W4-3-3-4

--- Page 17 ---
SECTION 4 TRAVEL SYSTEM
                                                     Group 3 Axle

  Disassembly of Differential Case (only Axle
  equipped with TPD)

dCAUTION: Ring gear (33) weight: 24 kg (53 lb)                  51. Remove side gears (38) (2 used), spider (49), pinions
dCAUTION: Do not drop ring gear (33).                               (65) (4 used), thrust washers (37) (2 used), and thrust
                                                                    washers (66) (4 used) from differential case B (36)
 48. Remove bolts (30) (16 used) and washers (31) (16
                                                                    and differential case A (32).
     used) from differential case A (32). Remove ring gear
     (33) from differential case A (32).
                                                                     36         38                         65
     j : 24 mm


                                                   30, 31

   33
                                                   32
                                                                                                      32        49
                                                                                                             W4GB-03-03-026


                                                                52. Remove the inner races of bearings (20) (2 used)
                                             W4GB-03-03-024         from differential case B (36) and differential case A
                                                                    (32) by using a bearing puller.
 49. Put the matching marks at the jointed part between
     differential case B (36) and differential case A (32).
     Remove bolts (34) (12 used) and washers (35) (12
     used) from differential case B (36).

     j : 17 mm
                                                                                                            20

                                                                      36
                                                34, 35


        36

                                                                                                             W4GB-03-03-027


        32
                                             W4GB-03-03-025


dCAUTION:
 (58 lb)
          Differential case A (32) weight: 26 kg

 50. Tap the center of spider (49) and remove differential
     case A (32) from differential case B (36).


                                                         W4-3-3-14

--- Page 19 ---
SECTION 4 TRAVEL SYSTEM
                                                       Group 3 Axle

 19. Turn over the differential case assembly. Remove
     bolts (F) (M12, Pitch 1.25 mm) (2 used) which have                                   1
                                                                                     16        3
     been temporarily installed in step 17.
 20. Apply LOCTITE #263 or equivalent to the thread                             14                 5
     part of bolts (30) (16 used). Install ring gear (33) with
     bolts (30) (16 used) and washers (31) (16 used).                   12                              7

fNOTE: Refer to the illustration for the order to tighten
   bolts (30).                                                         10                                   9
     j : 24 mm

     m : 225 N·m (166 lbf·ft)                                               8                           11


                                                                                 6                 13

                                                  33                                 4        15
                                                                                          2

                                                  30, 31                                           WNDB-04-03-012

    77


                                               W4GB-03-03-042


                                                           W4-3-3-24

--- Page 20 ---
SECTION 4 TRAVEL SYSTEM
                                                                   Group 3 Axle

     Installation of Brake

dCAUTION:   Use the parts which are used
 for adjustment of brake disc clearance when
                                                                            57. Install shaft (42) to the spline of side gear (38) (in
                                                                                case of axle equipped with LSD: (79)) in case (5).
   installing the brake.                                                    58. Install two pieces of pins (67) (8 used) to the bottom
 54. Install D-rings (27, 29) to the groove of the outer                        of case (5). Then, install brake ring (24).
     surface of brake piston (28). Apply grease onto
     D-rings (27, 29).                                                     dCAUTION:   Select the thickness of brake ring (24)
                                                                            which has been selected for adjustment of brake
 55. Install brake piston (28) to case (5) by using the                       disc clearance.
     special tool (ST 7789).
                                                                            59. Install two pieces of pins (67) (8 used) to the bottom
                                                                                of case (5). Then, install brake ring (24).
                       a

                           ST 7789
                                                               5


                     28                                W4GB-03-03-061             67

a-    Thrust Bolt (M16, Pitch 2.0 mm, Thread part length: 50 mm or more)
                                                                                                                                24

 56. Apply LOCTITE #263 or equivalent to button head                                                                       W4GB-03-03-062
     bolt (41). Install springs (39) (8 used), adapters (40)
     (8 used), and button head bolts (41) (8 used) to case                  60. Install brake disc (21) to the spline of shaft (42).
     (5) through the piston hole of brake piston (28).                          Install brake ring (22).

          l : 6 mm                                                          61. Install second brake disc (21) so that the open hole
                                                                                fits to that of first brake disc (21).
          m : 49 N·m (36 lbf·ft)

          m : 41 N·m (30 lbf·ft) (a)


                                                              a


               39
          40
     41


                                                       W4GB-03-03-016


                                                                    W4-3-3-34

--- Page 21 ---
SECTION 4 TRAVEL SYSTEM
                                                Group 4 Propeller Shaft


                                                               1        A


                           a
                                                                            WNEK50-04-04-001
a-    Vehicle Front Side


     3. Disconnect the both ends of pipe (1).                Detail A

       j : 17 mm


                                                                                       1


                                                                            WNEK50-04-04-004


                                                       W4-4-1-2

--- Page 22 ---
SECTION 4 TRAVEL SYSTEM
                                              Group 4 Propeller Shaft


                                                    1               2   WNEK50-03-22-002


 13. Install under guard (front) (1) and under guard (rear)
     (2). (Refer to W3-22-1.)

fNOTE: Only for the machine with under guard


                                                        W4-4-1-12

--- Page 23 ---
SECTION 4 TRAVEL SYSTEM
                                                Group 5 Brake Valve

Assembly of Brake Valve                                       IMPORTANT: Strong force deforms flange (1). Handle
                                                                 it with care.
IMPORTANT: Before assembling, apply hydraulic oil               3. Secure flange (1) in a vise with the piston (14) side
   onto parts in order to prevent them from seizing.               down.
IMPORTANT: The brake valve is the susceptible                      4. Apply grease onto O-ring (10). Install O-ring (10) to
   hydraulic component to contamination. Keep the                     flange (1).
   parts clean when assembling.
IMPORTANT: Check the direction to install packing             IMPORTANT: Install tip (a) of rod (12) to hole (b) of
   (20) and scraper (21).                                        retainer (13) in order not to drop retainer (13)
                                                                 from rod (12).
  1. Apply hydraulic oil onto packing (20), scraper (21),
     and piston (14). Install packing (20), scraper (21),       5. Install springs (16, 17, 18), holder (11), and rod (12)
     and piston (14) to flange (1).                                to retainer (13). Install tip (a) of rod (12) to hole (b) of
                                                                   retainer (13).


    1                                               20                                  a


                                                    21
                                                                     13

                                            WNEC-04-05-005
                                                                                                       A

                                                                     b
IMPORTANT: Replace retaining ring (24) with the
   new one.                                                                                             View A

  2. Install retaining ring (24) to piston (14).                                                                 WNEC-04-05-007

                                                              a-    Tip of Rod (12)
                                                              b-    Hole


                                                         W4-5-2-4

--- Page 24 ---
SECTION 4 TRAVEL SYSTEM
                                                 Group 6 Steering Device

     Disassembly of Steering Valve                                     4. Remove O-ring (3) from plate (7).
IMPORTANT: As the setting changes, do not                              5. Remove plate (7) from housing (18).
   disassemble overload relief valves (23) (2 used).
                                                                       6. Install the special tool (ST 7862) to the spline part of
IMPORTANT: Do not disassemble inserts (24) (2 used)                       spool (8).
   and check valve (25).
                                                                       7. Install the cloth onto the teeth of star (5) which has
IMPORTANT: Strong force deforms housing (18).
                                                                          been removed at step 4. Install star (5) to the gear
   Handle it with care.
                                                                          part of drive (6).
  1. Secure housing (8) in a vise (a) with the cap (21) side
     up.
                                             2

               a                                                                c                                 8


                                                                       5


                                                                           6

                                                                                                 ST 7862
                                                                                                                      WNDB-04-06-009
                                                                  c-       Up
a-    Vise                                       W202-02-14-002


     2. Remove screws (1) (7 used) from cap (2). Remove
        cap (2) from housing (18). Remove O-ring (3) from
        cap (2).

       j : 13 mm
IMPORTANT: When removing rotor (4), do not drop
   star (5).
  3. Remove rotor (4) and star (5) from housing (18).


                                                            W4-6-2-2

--- Page 25 ---
SECTION 4 TRAVEL SYSTEM
                                                  Group 6 Steering Device


                                                                   a


                                                              1


                                                WPD850-04-06-001
                    3, 4                 2
a-    Vehicle Front Side


     Removal of Steering Cylinder (Left)
     3. Remove bolt, washer (3) and clip (4).

        j : 17 mm
     4. Disconnect the both ends of pipe (2).

        j : 17 mm
     5. Remove elbow (1).

        j : 14 mm


                                                             W4-6-7-2

--- Page 26 ---
SECTION 4 TRAVEL SYSTEM
                                                 Group 6 Steering Device

                                                                            Detail A   3               4             5


                                                                            2

                                                                                                                              1
A

                                                                            6

a


 2                                                                                                               WNEK50-04-06-031


a-    Vehicle Front Side                                1

                                                    WNEK50-04-06-030


     Installation
     Installation of Steering Cylinder (Right)
                                                                   dCAUTION:   Metal fragments may fly off when
                                                                    a hammer is used. Wear necessary protection,
     1. Install all removed adapters to steering cylinder (1).          such as goggles, hard hat, etc. in order to prevent
                                                                        personal injury.
dCAUTION:
 lb)
          Steering cylinder (1) weight: 24 kg (53                      4. Install pin (5) by using a hammer.
                                                                       5. Install washer (4) and bolt, washer (3).
     2. Attach nylon slings onto steering cylinder (1). Hoist
        steering cylinder (1). Fit the hole at cylinder bottom            j : 19 mm
        side to the cylinder mounting hole of front frame
        (2).                                                              m : 90 N·m (66 lbf·ft)
IMPORTANT: Use one or more shims (6) respectively
   at the top and bottom sides.
  3. Fit shims (6) to the top and bottom sides of the
     cylinder bottom hole. Adjust the total clearance at
     the top and bottom sides of steering cylinder (1)
     and front frame (2) within 1 mm (0.039 in.).

fNOTE: Shim (6) thickness:            0.5 mm (0.02 in.), 1 mm
                                      (0.039 in.)


                                                            W4-6-7-12

--- Page 27 ---
SECTION 4 TRAVEL SYSTEM
                                            Group 6 Steering Device


                                                     1                WNEK50-03-22-002


IMPORTANT: Check the hydraulic oil level. Start the
   engine. Operate the steering cylinder to the stroke
   end several times and check for any oil leaks.
 17. Install under guard (front) (1) (only for the machine
     with under guard). (Refer to W3-22-1.)


                                                      W4-6-7-22

--- Page 28 ---
SECTION 4 TRAVEL SYSTEM
            Group 6 Steering Device

(Blank)


                  W4-6-8-10

--- Page 29 ---
SECTION 4 TRAVEL SYSTEM
                                       Group 7 Secondary Steering Device

                                                                           1


                                                                               WPD850-03-01-003
                                                                   3   2

View the complete manual on HeyDownloads →