PDF Service Repair Manual New Holland TD4020F TD4030F TD4040F Tractor - 2 MB

This complete service and repair manual covers the New Holland TD4020F, TD4030F, and TD4040F tractors.

It contains step-by-step instructions, detailed diagrams, and specifications used by professional mechanics.

From engine overhauls to hydraulic system troubleshooting, this manual has all the information you need.

Keep your specialty tractor in top condition with this essential guide.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
7)6:-')Ý1%29%0
8(*ÝÝ8(*ÝÝ8(*
           8VEGXSVW


         4VMRXß2Sß

--- Page 3 ---
2                            SECTION 00 – GENERAL – CHAPTER 1

                                          NOTES FOR SPARE PARTS
           Use exclusively genuine NEW HOLLAND spare parts, the only ones bearing this logo.


Only genuine parts guarantee same quality, life, safety as original components as they are the same as mounted
in production.
Only the NEW HOLLAND genuine spare parts can offer this guarantee.
All spare parts orders should be complete with the following data:
– tractor model (commercial name) and frame number;
– engine type and number;
– part number of the ordered part, which can be found on the “Microfiches” or the “Spare Parts Catalogue”,
    which is the base for order processing.


                                           NOTES FOR EQUIPMENT
Equipment which NEW HOLLAND proposes and shows in this manual are as follows:
– studied and designed expressly for use on NEW HOLLAND tractors;
– necessary to make a reliable repair;
– accurately built and strictly tested to offer efficient and long–lasting working means.
We also remind the Repair Personnel that having these equipment means:
– work in optimal technical conditions;
– obtain best results;
– save time and effort;
– work more safely.


                                                       NOTICES
Wear limits indicated for some details should be intended as advised, but not binding values. The words “front”,
“rear”, “right hand”, and “left hand” referred to the different parts should be intended as seen from the operator’s
seat oriented to the normal sense of movement of the tractor.


                       HOW TO MOVE THE TRACTOR WITH THE BATTERY REMOVED
Cables from the external power supply should be connected exclusively to the respective terminals of the tractor
positive and negative cables using pliers in good condition which allow proper and steady contact.
Disconnect all services (lights, wind–shield wipers, etc.) before starting the tractor.
If it is necessary to check the tractor electrical system, check it only with the power supply connected. At check
end, disconnect all services and switch the power supply off before disconnecting the cables.
84285927 – 02 – 2010

--- Page 4 ---
6                        SECTION 10 – ENGINE – CHAPTER 1


                              ENGINE TROUBLESHOOTING
                                                                                                      (cont)

            Problems                 Possible Causes                             Solutions

Engine overheating.        1. Coolant pump malfunction.            Overhaul pump        and    replace   if
                                                                   necessary.

                           2. Thermostat faulty.                   Replace the thermostat.

                           3. Radiator inefficient.                Remove internal deposits by flushing.
                                                                   Check for leaks and repair.

                           4. Deposits in cylinder head and Flush out coolant system.
                              crankcase coolant passages.

                           5. Coolant pump and fan drive belt Check and adjust belt tension.
                              slack.

                           6. Coolant level low.                   Top up expansion tank with specified
                                                                   coolant mixture.

                           7. Incorrect engine timing.             Check and adjust engine timing.

                           8. Injection pump calibration incor- Calibrate pump on test bench to va-
                              rect – delivering too much or too lues specified in calibration tables.
                              little fuel.

                           9. Air filter clogged.                  Clean filter unit and replace filter el-
                                                                   ement if necessary.

Engine lacks power and 1. Injection pump timing incorrect.         Adjust injection pump timing.
runs unevenly.

                           2. Auto advance regulator in injec- Overhaul injection pump and adjust
                              tion pump damaged.               on test bench to values specified in
                                                               calibration table.

                           3. Control valve journal worn.          Overhaul injection pump and adjust
                                                                   on test bench to values specified in
                                                                   calibration table.

                           4. Injection pump delivery irregular. Overhaul injection pump and adjust
                                                                 on test bench to values specified in
                                                                 calibration table.

                           5. All–speed governor damaged.          Overhaul injection pump and adjust
                                                                   on test bench to values specified in
                                                                   calibration table.

                           6. Injectors partially obstructed or Clean and overhaul injectors and ad-
                              damaged.                          just pressure setting.

                           7. Impurities or water in fuel lines.   Disconnect fuel lines from injection
                                                                   pump and clean thoroughly. If
                                                                   necessary clean and dry the fuel tank.
                                                                                                (continued)


84285927 – 02 – 2010

--- Page 5 ---
16                             SECTION 10 – ENGINE – CHAPTER 1


30. Remove the electrical connection of pump
    cut–out solenoid sender (1).


                                                                     28
31. Remove the retaining bolts (1) and 2 for the
    support. Remove the retaining nut (3) and detach
    the throttle control tie–rod connected to the
    injection pump.                                       3      4
32. Remove the hand and foot throttle cables
    complete with their support (4).


                                                                     29
33. Disconnect the electrical connection (1) between
    the cab and the engine.


                                                                     30
34. Disconnect the electrical connections from
    starter motor (1).


                                                                     31

84285927 – 02 – 2010

--- Page 6 ---
2                                      SECTION 18 – CLUTCH – CHAPTER 1


                                                           BOLT TORQUES

                                                                                                           Tightening torque
                        PARTS TO BE TIGHTENED                                               Thread
                                                                                                          Nm           kgm
11”/11” clutch/flywheel retaining bolts . . . . . . . . . . . . . . . . . . . . . . . .   M 8 x 1.25     20 ÷ 25      2 ÷ 2.5

Release command fork securing bolt (7, fig. 1)                                            M 16 X 1.5    136 ÷ 165   13.9 ÷ 16.1

Clutch housing/engine retaining nuts . . . . . . . . . . . . . . . . . . . . . . . .      M 12 x 1.25   117 ÷ 129   11.6 ÷ 13.1

Nut for sleeve cover fixing stud (6, fig. 1) . . . . . . . . . . . . . . . . . . . .      M 8 x 1.25     20 ÷ 25      2 ÷ 2.5


SPECIAL TOOLS

Warning – The operations described in this section
cannot be carried out without the ESSENTIAL tools
marked with an (X).
To work safely and efficiently and obtain the best
results, it is also necessary to use the recommended
specific tools listed below and certain other tools,
which are to be made according to the drawings
included in this manual.


List of specific tools required for the various
operations described in this Sect.
X 380001612          Pin for centering and adjustment of
                     11”/11” clutches.
X 380000293          Clutch adjustment gauge
                     (with 380001612).

    380000256        Set of wrenches for adjustment of
                     levers in 11”/11” LUK clutches.
    50169        Guide pin for fitting the engine to the
                 clutch housing (see sect. 21).
    380000569 Movable tool for dismantling tractors
              with bracket 380000500 and adapter
              plate 380000844.


84285927 – 02 – 2010

--- Page 7 ---
12                            SECTION 18 – CLUTCH – CHAPTER 1


30. Remove the electrical connection of pump
    cut–out solenoid sender (1).


                                                                    29
31. Remove the retaining bolts (1) and 2 for the
    support. Remove the retaining nut (3) and detach
    the throttle control tie–rod connected to the
    injection pump.                                      3      4
32. Remove the hand and foot throttle cables
    complete with their support (4).


                                                                    30
33. Disconnect the electrical connection (1) between
    the cab and the engine.


                                                                    31
34. Disconnect the electrical connections from
    starter motor (1).


                                                                    32
84285927 – 02 – 2010

--- Page 8 ---
22                              SECTION 18 – CLUTCH – CHAPTER 1


CHECKS, MEASUREMENTS AND REPAIRS
– DUAL DISK CLUTCH

                       ATTENTION
Handle all parts carefully. Do not put your hands or
fingers between parts. Wear the prescribed safety
clothing, including goggles, gloves and safety
footwear.


Minimum permissible dimensions after refacing of
parts subject to wear in the 11”/11” dual clutch          25966
A w 15.5 mm; B w 22.7 mm; D w 15.8 mm.
                                                                  60
1. Flywheel.
2. PTO clutch pressure plate.
3. Main clutch pressure plate.
4. Clutch cover.

Minimum permissible dimensions after refacing of
parts subject to wear in the 11” single clutch
A w 15.5 mm; C w 15.8 mm.
1. Flywheel.
2. PTO clutch pressure plate.
3. Clutch cover.


–    Check for wear on the Power take–off (11, fig. 1
     and 1, fig. 2) and main (9) clutch disks and
     replace if the retaining rivets are worn or
     approaching the friction material.
                                                          25967

–    Replace the disc when the oil has soaked into the            61
     organic agglomerate surfaces.

Minimum permissible dimensions after refacing
of parts subject to wear in the 11”/11” dual clutch
and 11” single clutch.

–    Check the friction surface conditions of the
     pressure plates and the clutch casing.
     Generally, by means of turning, up to 1 mm of
     material can be removed from the cast iron
     friction surfaces of the clutch cover (3), the
     pressure plate ring (2) and the flywheel (see
     section 10 chap. 1, page 56).
When parts (1), (2), (3) and (4) ( figs. 54 and 55) are
to be repaired by removing material, proceed as
follows:


84285927 – 02 – 2010

--- Page 9 ---
6                           SECTION 21 – TRANSMISSIONS – CHAPTER 1


    TRE0556A

                                                                                                 6


Sealing compound application diagram for mating surfaces between engine, clutch casing and rear
                                   transmission–gearbox.
                       The types of sealing compound to use are indicated on page 1, Sect. 00.
84285927 – 02 – 2010

--- Page 10 ---
8                       SECTION 21 – TRANSMISSIONS – CHAPTER 2

8. Detach the retaining springs and withdraw the
   sliding sleeves (1).                                    1


                                                        24999

                                                                            18
9. Unscrew the retaining bolts and remove the
   sleeve cover / support (1).                             1


                                                        25000

                                                                            19
10. Unscrew the two securing bolts (1) of the sliding
    sleeve control forks (2).                              1    2


                                                        25001

                                                                            20
11. Withdraw the external clutch control levers (1)
    and remove the forks (2).                                           1


                                                                    2
                                                        25002

                                                                            21

84285927 – 02 – 2010

--- Page 11 ---
8                        SECTION 21 – TRANSMISSIONS – CHAPTER 3

4. Unscrew the retaining bolts and remove the cov-
   er (1).


                                                                          8
5. Remove circlip (1).


                                                                      1


                                                                          9
6. Remove the collet (1).


                                                                  1

                                                                          10

7. Slide out constant mesh gear (1).

                                                     1


                                                                          11

84285927 – 02 – 2010

--- Page 12 ---
18                        SECTION 21 – TRANSMISSIONS – CHAPTER 3

24. Install the circlip (1) inside of the constant mesh
    gear (2).


                                                            1

                                                                    2


                                                                            47
25. Install the roller bearing (1) inside of the constant
    mesh gear (2).


                                                            1

                                                                        2


                                                                            48
26. Install the thrust washer (1).


                                                                1


                                                                            49
27. Install the driven shaft gear (1) together with the
    roller bearings and install the thrust washer.


                                                            1

                                                                            50

84285927 – 02 – 2010

--- Page 13 ---
6                            SECTION 23 – DRIVE LINES – CHAPTER 1


                                                          8
                                                                             1        3
                                           6


                                                                                              7


              5


                                                               4


                             2


                                                                                                         5
                               Sectional view of drive gear with electrohydraulic coupling
1.   FWD control valve and it’s solenoid.                       5. FWD engagement sensor.
2.   FWD inlet union to transfer box.                           6. Pressure control valve return line.
3.   Diff Lock control valve and it’s solenoid.                 7. Return oil union to gearbox.
4.   Supply pressure pipe to valve block.                       8. Pressure control valve


84285927 – 02 – 2010

--- Page 14 ---
16                     SECTION 23 – DRIVE LINES – CHAPTER 1


84285927 – 02 – 2010

--- Page 15 ---
10                     SECTION 25 – MECHANICAL FRONT AXLE – CHAPTER 1

3. Attach nylon slings to the front weights (1).
   Loosen the locking screw from each weight, lift
   the weights clear of the tractor and place them in
   a safe position.


                                                        27786

                                                                            7

4. Unscrew bolts (2) and remove the drive shaft
   guard (1).
                                                                        2


                                                                1


                                                                            8
5. Remove the circlip (2) and move the front sleeve
   (1) backwards in order to free it from the groove       1        2
   on the front axle.


                                                        25647

                                                                            9
6. Remove the circlip (2) and move the front sleeve
   (1) backwards in order to free it from the groove
   on the front axle.


                                                                            9

84285927 – 02 – 2010

--- Page 16 ---
20                     SECTION 25 – MECHANICAL FRONT AXLE – CHAPTER 1


Reassemble the front axle adhering to the follow-
ing instructions:


– Refer to the illustrations on pages 6, 7 and         – Install the axle shaft and relative bolt.
  8 to check the orientation of the various
  components.                                          – Fit the stub axle, the adjustment shims, the
                                                         upper and lower pivot pins, the mudguard
– Respect the tightening torques prescribed on           bracket and related bolts.
  page 3.
                                                       – Fit the wheel hub, the ring gear of the final drive
– Carry out the adjustments described on pages           unit and the lock ring. Tighten to the prescribed
  29 to 36.                                              torque value, while simultaneously turning the
                                                         wheel hub, to ensure that the bearings are
– Install the rear bearing, the seal, the dust seal,     correctly seated.
  the adjustment shims, the spacer and the bevel
  drive pinion shaft complete with front bearing.      – Fit the securing and stop circlips, the sun gear
                                                         and the cover of the final drive unit.
– Position the detent ball, screw in the bevel drive
  pinion lock nut and secure in position by            – Fit the pins, washers, spacers and steering
  staking. Finally, replace the circlip.                 cylinders.

– Install the crown wheel–differential assembly,       – Install the track rod, the front and rear supports
  the support caps and tighten the relative bolts.       and the oil drain plugs.

– Install the bevel drive–differential housing on
     the front axle casing.


84285927 – 02 – 2010

--- Page 17 ---
30                     SECTION 25 – MECHANICAL FRONT AXLE – CHAPTER 1

            S = Sp + {(0.18 – Gm) x 1.35}
where:
Sp = thickness of test shim installed in the bevel
drive–differential housing.
Gm = average backlash measured between the
sides of the teeth of the bevel drive.
15. Fit a shim of the calculated thickness and with a
    1/100 scale dial gauge positioned perpendicular
    to the outside edge of one of the crown wheel
    teeth, check that the backlash between the
    pinion and the crown wheel is within the pre-
    scribed tolerance limits 0.15 ÷ 0.20 mm (0.0059
    to 0.0079 in.).
16. Using wrench 380000252, for TD4020, TD4030
    or TD4040 models, turn the adjuster ring nut and,
    using torque wrench 380001633 fitted on
    wrench 380000257 (1, fig. 73), check that the
    rolling resistance torque of the crown wheel and
    pinion bearings, as measured in the same
    conditions used to check only the pinion, is:


  A2 = A1 + 1 P 1.5 Nm (0.7376.5 to 1.1063 ft lb)
 where:
 A2 = pinion–crown wheel rolling resistance torque;
 A1 = rolling torque of pinion only, 0.5 Nm (0.3688
 lb) for TD4020, TD4030 and TD4040 , with the pi-
 nion fitted with the seal, measured previously;
 1 P 1.5 Nm (0.7376.5 to 1.1063 ft lb) = rolling resi-
 stance torque of crown wheel only measured at
 the end of the pinion, using wrench 380000257
 and torque wrench 380001633.

                                                         24587

                                                                        73


17. Tighten the cap bolts (C1, page 3) to a torque
    of 143 Nm (105.475 ft lb).

18. Fit the safety plates, screwing the adjustment
    ring nut in or out, to reach the nearest notch.

19. Attach the differential bevel drive carrier to the
    axle casing after having carefully cleaned and
    degreased the mating surfaces and apply
    sealing compound (approx. 2 mm (0.0787)
    along the marked line shown in the drawing
    below.
                                                         24591

                                                                        74


84285927 – 02 – 2010

--- Page 18 ---
4                 SECTION 27 – REAR AXLE AND TRANSMISSION – CHAPTER 1

                                      SECTIONAL VIEWS


           C1 59 Nm        C2 98 Nm


                                       C4 221 Nm                C3 221 Nm


         C7 245 Nm


                                          C9 59Nm


    C6 255Nm


                           C5 98 Nm

                                                           C8 123 Nm
                                          C10 180Nm


                                                                            1


84285927 – 02 – 2010

--- Page 19 ---
14                SECTION 27 – REAR AXLE AND TRANSMISSION – CHAPTER 1

18. Remove two metal clamps (1) and the rigid pipe (2)
    of drawing oil from the transmission housing via lift
    pump.


                                                                        22
19. Remove the retaining bolts (1) and 2 for the
    support. Remove the retaining nut (3) and
    detach the throttle control tie–rod connected to
    the injection pump.
                                                            3   4

20. Remove the hand and foot throttle cables
    complete with their support (4).


                                                                        23

21. Unscrew the retaining bolts (1) and remove the
    main and range gear selector levers.


                                                                        24
22. Remove the floor mat


                                                                        25

84285927 – 02 – 2010

--- Page 20 ---
24                SECTION 27 – REAR AXLE AND TRANSMISSION – CHAPTER 1

63. Use a chain to attach the tow hook and PTO to
    the hoist. Remove the three retaining bolts (1)
    from both sides and remove the unit from the
    rear transmission–gearbox case.


                                                                            TRE0191A


                                                                                  62
64. Unscrew the nut (1) and remove the bolt.
    Remove the right–hand lower link (3) and its
                                                                        3
    spacer (2). Repeat on the left–hand lower link.


                                                                                       3


                                                         25773
                                                                    2

                                                                                  63
65. Attach a belt to both the ends of the torsion bar
    (1). Ensure that belt is strong enough to lift the    1
    assembly. Remove the retaining bolts (2) and
    take off the assembly.


                                                                        2

                                                         TRE0508A


                                                                                  64
66. Remove the bolts securing the gearbox cover
    (1). Remove the cover.


                                                         TRE0104A


                                                                                  65

84285927 – 02 – 2010

--- Page 21 ---
34                SECTION 27 – REAR AXLE AND TRANSMISSION – CHAPTER 1

27. Insert the gear shift forks (1) and (3) on the
    sliding rings (2) and (4) of the synchronisers.          1        2   3
28. Fit the bevel pinion complete with all the parts
    and carry out the adjustments given on pages 38                       4
    to 40.


                                                          25912


                                                                              24


29. Fit the gearbox drive shaft complete with all parts
    and the adjuster shim, then position the bearing
    (2) and secure it using the snap ring (1).
                                                             1    2


                                                          25796


                                                                              25


30. Insert the final drive driving shaft from the rear
    end, fit the bearing (2) into its seat and secure        1            2
    with the snap ring (1).


                                                          25913


                                                                              26


84285927 – 02 – 2010

--- Page 23 ---
44                SECTION 27 – REAR AXLE AND TRANSMISSION – CHAPTER 1

10. Lock the right and left–hand ring nuts in
    position with the lock ring (1).


                                                                        48


84285927 – 02 – 2010

--- Page 24 ---
2                                  SECTION 31 – POWER TAKE–OFF – CHAPTER 1

                                                          MECHANICAL POWER TAKE–OFF
                                                                                                                                         (continued)
                                                                                                               TD4020F – TD4030F – TD4040F
2–speed 540/750 rev/min PTO (option – all models)
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                 as for single–speed PTO
Engagement and control . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                                   as for single–speed PTO
Direction of rotation (viewed from rear of tractor) . . . . . . . . .                                              as for single–speed PTO
Speed selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                      by means of hand lever located to
                                                                                                                  rear RH side of driver’s seat
Engine speed with PTO shaft rotating at 540 rev/min . . . . .                                        rev/min                 2196
Engine speed with PTO shaft rotating at 750 rev/min . . . . .                                        rev/min                 2132
PTO speed with engine at maximum power speed (2500
rev/min:
– for 540 rev/min PTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                    rev/min                  566
– for 750 rev/min PTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                    rev/min                  809

Ground speed PTO. Rear wheel speed with PTO shaft                                                     wheel
rotating at 540 rev/min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                 speed          see 540 rev/min PTO
                                                                                                     rev/min
Ground speed PTO. Rear wheel speed with PTO shaft                                                     wheel
rotating at 750 rev/min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                 speed                  10.14
                                                                                                     rev/min

Diameter of driven shaft at grooved terminal . . . . . . . . . . . .                                                   13/8 in. (6–spline)


84285927 – 02 – 2010

--- Page 25 ---
12                      SECTION 31 – POWER TAKE–OFF – CHAPTER 1

540/750 MECHANICAL PTO
Removal – Refitting (Op. 31 112 20)


                       WARNING
Lift and handle all heavy parts using lifting tackle of
sufficient capacity.
Make sure that the units or parts are supported by
suitable harnesses and hooks. Check that no one is
in the vicinity of the load to be lifted.


1. Disconnect the negative cable from the battery.


2. Remove the top link (1) of the three–point
   linkage.
                                                             1


                                                          TRE0819A

                                                                         12
3. Remove the tow hook (1), if fitted.


                                                                     1

                                                          24953

                                                                         13
4. Remove the tow bar (1), if fitted.
                                                             1


                                                          24954

                                                                         14

84285927 – 02 – 2010

--- Page 26 ---
4                         SECTION 33 – BRAKING SYSTEM – CHAPTER 1

                                       DESCRIPTION AND OPERATION


SERVICE BRAKES                                            this causing actuator discs to turn, ball (3) in the ta-
                                                          pered seats to force the discs apart as shown in detail
The service brakes are hydraulic with oil bath discs.     (c).

The two control pumps (one for each pedal) are            As a result, two simultaneous actions compress the
housed in the front section of the cab and are con-       brake discs against the differential support (8) and
nected to their respective pedals by means of two         the back up discs, immediately upon releasing the
rods.                                                     pedal spring (7), pull the actuator (4) back into the
                                                          rest position (figure b and detail d) and as a result the
These pumps can be actuated either independently          discs are released. The action is similar when the
or together. If actuated together, the pedals are con-    right–hand brake pedal is pressed (Rd).
nected by a pin.
                                                          The brake discs (one for each rear wheel) are posi-
A connecting pipe between the two pumps ensures           tioned between the rear transmission box and the lat-
balanced braking even when the brake discs are not        eral final drive box and are splined onto the differen-
equally worn.                                             tial output half–shafts.
The two control pumps are fed from a single tank lo-
cated above the pumps.                                    PARKING BRAKE
The service brakes are slave cylinder operated.
When the left–hand brake pedal (fig. a ) is de-           When the hand brake lever (Lm) is pulled, the control
pressed, the master cylinder (MS) sends the oil to the    cable (14) pulls the control lever (13), at the direction
slave cylinder (SL). The brake links (1) move as indi-    of arrow. Then the brake links (1) acts on the brake
cated by the arrows, by the help of slave cylinder (SL)   discs.


84285927 – 02 – 2010

--- Page 27 ---
14                       SECTION 33 – BRAKING SYSTEM – CHAPTER 1

9. Remove rear hood retaining nuts.


                                                                             27
10. Remove rear hood.


                                                                             28
11. Remove the electrical connections:from the
    pressure sensor (1) and remove the service                      1
    brake control pipes (2).


                                                                        2


                                                                             29
12. Remove the retaining pins and withdraw the
    brake pump control fork articulation dowels (1).
13. Undo the bolts (2) that secure the brake control
    pumps to the cab and withdraw the pumps from
    the engine side.

                                                                        10


                       WARNING
Use appropriate tools to align the holes. NEVER
USE YOUR FINGERS OR HANDS.
                                                       26273


                                                                             30

84285927 – 02 – 2010

--- Page 28 ---
4                                SECTION 35 – HYDRAULIC SYSTEM – CHAPTER 1

                                   MAIN SPECIFICATION OF HYDRAULIC PUMP (All models)
                                                                                                                                          (continued)
Driven and driving gear shaft diameter . . . . . . . . . . . . . . . . . . . . . .                            mm              17.400 – 17.418
                                                                                                              (in.)          (0.6850 – 0.6857)
Internal diameter of seats in supports . . . . . . . . . . . . . . . . . . . . . . .                          mm              17.450 – 17.470
                                                                                                              (in.)          (0.6870 – 0.6878)
Clearance between gear shafts and their seats . . . . . . . . . . . . . . .                                   mm               0.032 – 0.070
                                                                                                              (in.)          (0.0013 – 0.0025)

View the complete manual on HeyDownloads →