PDF Service Repair Manual Case 9007B Hydraulic Excavator - 12 MB

This service repair manual is the definitive guide for the Case 9007B Hydraulic Excavator.

It provides technicians with detailed, step-by-step instructions for all aspects of repair and maintenance.

From the hydraulic system to the engine, this manual contains the specifications and procedures needed to perform professional-level service.

It's an indispensable tool for keeping your Case excavator working hard.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 5 ---
2000-2

                                                            TABLE OF CONTENTS
SPECIFICATIONS..................................................................................................................................................... 3
SPECIAL TORQUES................................................................................................................................................. 3
ENGINE..................................................................................................................................................................... 4
  Removal and installation .......................................................................................................................................4

          WARNING: This symbol is used in this manual to show important safety messages. Whenever you see
    !     this symbol, read the message which follows carefully, since there is a risk of serious injury.


Cre 7-21950GB                                                                                                                 Issued 04-99                 Printed in U.K.

--- Page 7 ---
4001-4

                                               MAXI-FUSES                                                                    FUSES


                                                            F2 F3


                                                             F1
                                                                                                                                                                                 CS99B512


                                                                                                 F4
                                                                                                                                                        F14
                                                                                          F5
                                                                                                                                                                   F15
                                                                                                 F6
                                                                                                                                                        F16
                                                                                          F7                                                                       F17
                                                                                                 F8                                                     F18
                                                                                                                                                                   F19
                                                                                          F9
                                                                                                                                                        F20
                                                                                                F10
                                                                                                                                                                   F21
                                                                                         F11                                                            F22
                                                                                                F12
                                                                                         F13                                                                       F23
                                                                    CI99A503
                                                                                                                                                                                CS98M567

F1   45A = Maxi-fuse + 24 Volts before battery relay
     (F4 and F5)                                                               F4  10A Left/right-hand switch panel, radio, air   F14 15A Throttle motor driver
F2   45A = Maxi-fuse + 24 volts after battery relay                                conditioner unit.                              F15 10A Relay K3, left-hand panel, swing lock,
     (F16)                                                                     F5 10A Starter switch                                  swing brake, travel speed and audible travel
F3   45A = Maxi-fuse + 24 volts after battery relay                            F6 20A Heater, air conditioner                         alarm
     (alternator charge and F6, F7, F8, F9, F10, F11,                          F7 20A Working light (upperstructure and           F16 20A Engine shut-down solenoid
     F12,F13, F14, F15, F17, F18, F19, F20, F21,                                   attachment)                                    F17 10A Control lock
     F22, F23)                                                                 F8 15A Not used                                    F18 10A Not use
                                                                               F9 15A Not used                                    F19 10A Beacon
                                                                               F10 15A Not used                                   F20 20A Oil pump
                                                                               F11 10A Wiper and washer pump motor                F21 15A Option solenoid
                                                                               F12 10A Horn and cab light                         F22 10A Not used
                                                                               F13 10A Radio and cigarette lighter                F23 10A Not used


Cre 7-22810                                                                                                                                         Issued 02-99         Printed in U.S.A.

--- Page 8 ---
4001-14

                                                                                             ELECTRICAL SCHEMATIC (PLATE D)
                                                              CAB                                             CAB FLOOR
                                                              A2    CPU (right-hand switch panel)             A1   Throttle motor driver
                                                              S1    Left-hand switch panel                    F5   10A Key switch
                                                              S2    Right-hand switch panel                   F14 15A Throttle motor driver
                       M2                                     S3    Key switch
                       R2-R3-R4-R5
                       S24-S25                                S9    Engine idle switch
                       P8
                                                              P1    Monitor display


                                                                                                              THROTTLE MOTOR
                                                              RIGHT-HAND ARMREST CONTROL PANEL                P8   Throttle motor potentiometer
                                                              P5    Throttle motor potentiometer              R2   Throttle motor coil A1
     S3                                                                                                       R3   Throttle motor coil B1
                                                                                                              R4   Throttle motor coil B
                                                                                                              R5   Throttle motor coil A
                                                                                                              S24 Throttle motor limit switch (cw)
                                                                                                              S25 Throttle motor limit switch (ccw)


                                                                                                              RIGHT-HAND SWITCH PANEL
    S9
                                                              ENGINE                                          S21 Work mode selection switch
                                                              M2    Throttle motor

    P1                                                                                                        LEFT-HAND SWITCH PANEL
                                                                                                              S11 Emergency stop switch


          F5-F14

                                          S1-S11


                   S2-A2-S21         A1
                   P5


                                                   CI98N513


Cre 7-22810                                                                                                                       Issued 02-99        Printed in U.S.A.

--- Page 9 ---
4001-24

                                                             One touch idle control
                                                             When the one touch idle switch is pushed, the motor
                                                             driver senses the idle switch has been actuated.
                                                             There is a fixed voltage for one touch idle rotation
                                                             inside the motor driver, so the motor is rotated till the
                                                             potentiometer voltage of the throttle motor reaches
                                                             the same voltage as that of the motor driver.
                                                             To release the one touch idle, turn the engine key off
                                                             then turn it on again. There is no monitor display
                                                             during one touch idling.

                                                             Speed control for each mode
                                                                                                                         A
                                                             When the L mode button on the right-hand switch
                                                             panel is pushed, the signal enters the CPU and the L
                                                             mode transistor is activated. The motor driver senses
                                                             that L mode has been requested.
                                                             The throttle volume voltage inside the motor driver is
                                                             limited to that necessary for L mode engine speed. If
                                                             you push the L mode button when the throttle is at
                                                             maximum in S mode, the motor moves till it reaches
                                                             the L mode voltage.
                                                             To release the L mode, turn the engine key off and
                                                             then turn it on again.                                          1        2         3      B
                                                             There is no monitor display show the mode, but the
                                                                                                                                                           CM99A006
                                                             lamp beside the switch lights up.
                                                             A=    VOLTAGE
                                                  CS99A546   B=    SPEED
A1   Throttle motor driver                                   1-    MINI
A2   CPU (right-hand switch panel)                           2-    L MODE
M2   Throttle motor                                          3-    S MODE MAXI
P5   Throttle potentiometer
S2   Right-hand switch panel
S9   Engine idle switch
X5   Right-hand switch panel connector (16 way)
X6   Right-hand switch panel connector (16 way)
X7   Right-hand switch panel connector (3 way)
X17 Throttle motor connector (12 way)


Cre 7-22810                                                                                                                      Issued 02-99       Printed in U.S.A.

--- Page 10 ---
4001-34

                               COMPONENT ELECTRICAL TESTING                                       Water temperature sensor, oil tem-
Testing equipment                                                                                 perature sensor
- Service connector kit assembly :                                                                STEP 1
  P/N CAS 40031                                                                                   Remove the water temperature sensor and the oil
                                                                         1
                                                                             Y5                   temperature sensor.
- Digital multimeter                                                                                                                                                          1
                                                           Y3                     Y1              STEP 2
  CAS 1559                                                                                                                                                             4
                                                                                                  Connect the service connector (1) for 2P to the sen-                                                3
Solenoid valve testing (5 spools)                                                                 sor (2) which was removed.
                                                                                                                                                             5
Y1   Solenoid - swing lock                                                                         4 Thermometer                                                                      2
                                                                                                   5 Metal container
Y3   Solenoid - speed travel
                                                                                                   6 Tripod
Y4   Solenoid - swing brake
                                                                                                   7 Spirit burner
                                                                                                                                                                                      6
Y5   Solenoid - control lock
                                                                                   Y4             STEP 3
Y6   Solenoid - option                                                                                                                                                                7
                                                            Y6                                    To connect to the tester (3), connect the red/black
 1 Connector                                                                                      terminals to the spade terminal of a service connec-                                             CS99A851
                                                                                       CI99A513

STEP 1                                                                                            tor (1).
                                                                                                                                                         Water temp.
                                                                     2                            STEP 4                                                               Lower value        Upper value
Remove connector 1 from the solenoid valve.                                                                                                              (Oil temp.)
STEP 2                                                                                            After completing the connection, increase tempera-        68°F           8.00k Ω         10.20k Ω
                                                                                                  ture gradually, and check the resistance.                 86°F           5.35k Ω         6.50k Ω
Connect the service connector 2P (1) between the
removed connectors (solenoid valve (2) side only).                                                                                                         104°F           3.60k Ω         4.55k Ω
                                                                                                                                                           122°F           250k Ω           3.10KΩ
STEP 3
                                                                                                                                                           140°F           1.70k Ω         2.20k Ω
To connect to the tester (2), connect the red/black ter-
minal to the spade terminal of the service connector                                                                                                       158°F           1.20k Ω         1.55k Ω
(1).                                                                                                                                                       176°F           0.85k Ω         1.15k Ω
                                                                 1
STEP 4
                                                                                       CS99A842
Confirm the resistance after completing the connec-
tion.
Resistance 40 Ω (at 68°F)
 *Resistance value varies slightly with temperature.                 2


                                                                     1
                                                                                       CS99A843


Cre 7-22810                                                                                                                                                            Issued 02-99        Printed in U.S.A.

--- Page 11 ---
4002-4

                                                  BATTERY TEST
NOTE : To correctly test a battery, do each part of the
battery test until you know the condition of the
battery.

Visual Checks
 1.   Make sure the cable connections are clean and
      tight. Clean foreign material from the top of the
      battery.
 2.   Inspect the battery case, battery posts, and
      cables for damage.
 3.   Check the electrolyte level. See page 3.
 4.   If you added water to the battery, the battery
      must be charged for 15 minutes at 15 to 25
      amperes to mix the water with the electrolyte.

Specific Gravity Check
A hydrometer is used to check the specific gravity                                                                JS00532A
(weight) of the electrolyte. The specific gravity is an             TEMPERATURE IN °F        TEMPERATURE IN °C
indication of the level of charge for each cell.
                                                              4.   Make a record of the corrected specific gravity
Hydrometers are made to show the correct specific                  reading for each cell.
gravity when the temperature of the electrolyte is
                                                              5.   If the difference between the high reading and
26.7°C (80°F).
                                                                   the low reading is .050 or more, charge the
When you check the specific gravity, you must know                 battery and check the specific gravity again. If
the temperature of the electrolyte. If your hydrometer             after charging, the difference is still .050 or more,
does not have a thermometer, get a thermometer to                  install a new battery.
check the temperature of the electrolyte. The
                                                              6.   The corrected specific gravity reading shows the
thermometer must indicate a high temperature of at
                                                                   level of charge for the cell. The level of charge
least 52°C (120°F).
                                                                   must be at least 75% in each of the cells. In
 1.   Remove enough electrolyte from a cell so that                maintenance free batteries the level of charge is
      the float is free in the tube.                               at least 75% if the corrected specific gravity
                                                                   reading is 1.240 or higher. In all other batteries
NOTE : If the specific gravity cannot be checked
                                                                   the level of charge is at least 75% if the corrected
without first adding water to the cell, the battery must
                                                                   specific gravity reading is 1.230 or higher.
be charged for 15 minutes at 15 to 25 amperes to mix
the water with the electrolyte. Then check the specific       7.   If the difference between the high reading and
gravity.                                                           the low reading is less than .050, and the level of
                                                                   charge is at least 75% in all of the cells, do the
 2.   Read the float.
                                                                   Capacity (Load) Test.
 3.   Read the thermometer. If the reading is above
                                                              8.   If the difference between the high reading and
      26.7°C (80°F) add specific gravity points to the
                                                                   the low reading is less than .050, but the level of
      reading for specific gravity. If the reading is below
                                                                   charge is less than 75% in any of the cells,
      26.7°C (80°F) subtract specific gravity points
                                                                   charge the battery and check the specific gravity
      from the reading for specific gravity. See the
                                                                   again. If after charging:
      following illustration and add or subtract specific
      gravity points as needed.
                                                                    A. The level of charge is less than 75% in any
                                                                       of the cells, discard the battery.

                                                                    B. The level of charge is at least 75% in all of
                                                                       the cells, do the Capacity (Load) Test.


Cre 7-22000GB                                                                         Issued 03-99        Printed in U.K.

--- Page 12 ---
5002-6

                                      SPECIAL TOOLS


                                        926407                                              B407320M

 1.   Track removal press CAS 10044              2.   CAS - 1450 and CAS - 1682 for the followong
                                                      leakage test.
                                                 3.   Loctite 262
                                                 4.   Hammer
                                                 5.   Jig


Cre 7-22020GB                                                        Issued 04-99    Printed in U.K.

--- Page 13 ---
5002-16

                                 TRACK TENSION ADJUSTMENT
Check the tension of the tracks as required. Adjust        STEP 4
the tension for the type of surface the machine will be
operating on. Tighten the track for operation on hard      Do the following procedure to increase the track
surfaces and loosen the track for operation on soft        tension :
surfaces.                                                   1.   Clean the grease fitting for the track adjustment
                                                                 cylinder.
STEP 1
Park the machine on a hard level surface. Rotate the
upperstructure of the machine so that the cab is over
the track to be checked.
STEP 2


                                                                                                                JD00273A

                                                            2.   Check that the check valve is tight.


                                                JD00270A
Lower the bucket or tool to raise the machine until the
track to be checked is one to two inches from the
ground.
NOTE : If the machine does not have a bucket or tool
installed, install wood blocks under the arm and lower
the arm onto the wood blocks. Then, lower the arm to
raise the machine.
STEP 3
                                                                                                                JD00287A

                                                            3.   Inject grease into the track adjustment cylinder
                                                                 until the track tension is correct.


                                                JD01074A
Measure the distance between the bottom surface of
the track frame and the top surface of the track shoe.
The amount of track deflection must be 180 to
205 mm.


Cre 7-22020GB                                                                      Issued 04-99         Printed in U.K.

--- Page 14 ---
5002-26

STEP 5                                                     STEP 6


                                 1

                                            5                                                                  8
          5
                                                                     8

                                                                                1

                                                JS00305A                                                            JS00306A
Remove and discard face seal (5) from lower roller         NOTE : Do this step only if inspection step 3, page 27
(1) or shaft (6).                                          indicates bushings (8) require replacement.
                                                           Using a hammer and brass punch, drive the bushings
                                                           (8) from the track roller (1). Be careful not to damage
                                                           the seal bore in the track roller. Discard bushings.


                                       1

                                                                 8          5


                                                                                                    7
      2


                                                                                             4          3

                                                            6               5


                                                                                                                   JS00307A

                                            Lower Roller (Side View)


 1.   Lower Roller                     4.    End Cap                                7.   O-Ring
 2.   Drain Plug                       5.    Face Seal                              8.   Bushing
 3.   Retainer Ring                    6.    Shaft

Cre 7-22020GB                                                                        Issued 04-99           Printed in U.K.

--- Page 15 ---
5002-36

Inspection                                                      STEP 4
STEP 1                                                          Inspect the thrust plate for wear and damage.

Clean all parts in cleaning solvent.                            STEP 5
STEP 2                                                          Inspect the bore in the bracket (11) and the upper
                                                                roller (1) for damage that will result in leakage. Use
Inspect the bushing surfaces on the shaft (8) for               new parts as required.
scoring, pitting, and other damage. Measure the
diameter of the shaft in four places diagonally
opposite of each other. If the diameter of the shaft is
31 mm or less, replace the shaft.
STEP 3
Inspect the bushings for wear and damage. Measure
the ID of the bushing. If the ID of the bushing is 32.6
mm or more, replace the bushing. (Disassembly, see
page 35, step 7).


                               10                              10
         3                                                                    1
                                                                                        9


         6


         2

         4
                                                                                                        8


                     5
                         7                                                                     11
                                                                                                                   CS99A814

                                                Upper Roller (Side view)


 1.   Upper roller               4.    Cover                    7.   Thrust plate              10.   Bushing
 2.   Drain plug                 5.    O-ring                   8.   Shaft                     11.   Bracket
 3.   Screw                      6.    Screw                    9.   Face seal


Cre 7-22020GB                                                                         Issued 04-99          Printed in U.K.

--- Page 16 ---
5002-46

STEP 6                                                        Inspection
                                                              STEP 1
                                                              Clean all parts in cleaning solvent. Make sure that the
                                  7                           cavity in the idler wheel is clean. Dry all parts using
                                               7              low-pressure compressed air, then apply clean oil to
  7                                                           all parts.
                                                              STEP 2
                                                              Inspect the bushing surfaces on the shaft for scoring,
      2                                              2        pitting, and other damage. Measure the diameter of
                                                              the shaft in four places opposite of each other. If the
                     7                                        diameter of the shaft is 44 mm or less, replace the
                                                   JS00353A
                                                              shaft.
Remove and discard the face seal (7) from the idler           STEP 3
wheel (2) using a screwdriver or suitable tool. Be
careful not to damage the seal bore in the idler wheel.       Inspect the bushings for wear and damage. Measure
                                                              the ID of the bushing. If the ID of the bushing 45 mm
STEP 7                                                        or more, replace the bushing. Measure the width of
                      8                                       the bushing. If the width of the bushing is 39.6 mm or
                                           2                  less, replace the bushing.
                                                              STEP 4
                                                              Inspect the seal bore in the hubs and idler wheel for
                                                              damage that will result in leakage. Replace the parts
                                               8              with new parts as required.


                                                   JS00354A

NOTE : Do this step only if inspection (step 3)
indicates bushings (8) require replacement.
Using a hammer and brass punch, drive the bushings
(8) from the idler wheel (2). Be careful not to damage
the seal bore in the idler wheel.


Cre 7-22020GB                                                                       Issued 04-99       Printed in U.K.

--- Page 17 ---
5002-56

Assembly


                                                                                    1
                                                                              2


                                                                                            3
                                                    15
                                           14                                               4
                                      13
                                 12                                                         5
                      11

                                                                       7

                                                                                    6
                                                8
                                                     9
                                                         10
                                                                                                JS01084A

                     Track Adjustment Cylinder

 1.   Cap screw      6.   Grease Fitting                      11.   Piston Rod
 2.   Flat Washer    7.   Poppet                              12.   Wiper
 3.   Cap Screw      8.   Spring                              13.   Back-up ring
 4.   Lock Washer    9.   Ball                                14.   O-ring
 5.   Bracket       10.   Check Valve Body                    15.   Cylinder Tube

View the complete manual on HeyDownloads →