PDF Service Manual Tigercat 1045 1055 Forwarder - 2 MB

The official service manual for the Tigercat 1045 and 1055 Forwarders is the ultimate guide for technicians.

This manual covers everything from routine maintenance to complex repair procedures with detailed instructions and specifications.

It includes information on hydraulics, electrical systems, engine, and drivetrain.

Ensure your forestry equipment is maintained to factory standards and operates reliably with this indispensable resource.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
SERVICE MANUAL
                                          Tigercat 1045/1055 FORWARDER
                                                                                                                  Issue 1.0, AUGUST, 2006
TABLE OF CONTENTS

                                                                                                                                          SECTION
     INTRODUCTION .............................................................................................................. iii
     SAFETY ............................................................................................................................ 1
     CONTROLS AND OPERATION ........................................... SEE OPERATOR'S MANUAL
     LUBRICATION AND MAINTENANCE ............................................................................... 3
     ELECTRICAL AND COMPUTERS .................................................................................... 6
     ENGINE START & STOP .................................................................................................. 7
     DRIVE ............................................................................................................................... 8
     BRAKES ............................................................................................................................ 9
     OIL COOLER/RADIATOR, FAN AND HYDRAULIC RESERVOIR .................................. 10
     CENTER JOINT, STEERING, GATE AND SNOW BLADE ............................................. 11
     CRANE, GRAPPLE AND MAIN PUMP ........................................................................... 12


 1045/1055-SM00

1045/1055 Available Literature
Operator's Manual (10550101 to 10550200) ........................................................ Part No. 25900A
Operator's Manual (10450101 and 10550201 and up) ......................................... Part No. 29767A
Service Manual (10550101 to 10550200) ............................................................. Part No. 25901A
Service Manual (10450101 and 10550201 and up) (This Manual) ...................... Part No. 29768A
Parts Catalog ......................................................................................................... Part No. 25902A


                                                                                                                                 Tigercat
                                                                                                                                                     ®


                                                                                                                                 Tigercat Industries Inc.
                                                                                                                                 P.O. Box 544
                                                                                                                                 Paris, Ontario
                                                                                                                                 Canada N3L 3T6
                                                                                                                                 Tel: (519) 442-1000
                                                                                                                                 Fax: (519) 442-1855

--- Page 3 ---
Tigercat 1045/1055 Forwarder                                                                              Safety

    OPERATING SAFETY PRECAUTIONS
              continued
Before leaving operator's cab, place the crane in
the park position or on the ground and lower the
snow blade (if equipped) to the ground.
If out of the operator's cab for an extended period
shut the machine off.
When parking the machine:                                     Maintain a safe operating distance between the
                                                              machine and workers and all other personnel. It
•      Park on level ground ONLY.                             is the duty of the operator to ensure that no
•      Do not park on a hillside or incline.                  person approach the machine while in use, the
                                                              risk zone is 60 m (200 feet).
•      Place the crane in the park position or on the
       ground and lower the snow blade (if                    Never operate the crane or grapple over the
       equipped) to the ground.                               heads of bystanders.

•      Stop the engine and release pilot system               Use only prearranged and approved signalling
       pressure by performing the following steps:            practices.

       1. Close both doors. Turn key switch to the            Obey flagger's signal and signs
          ON position. Do not start the engine.               Operate the machine only from a seated position
          Press pilot reset switch.                           in the operator’s seat.
       2. Fully apply brake foot pedal 50 times or            Do not carry passengers either in the cab or
          more.                                               anywhere else on the machine.
       3. Pressure may remain in the system                   If vision is limited by dust, smoke, fog or snow,
          after completing all of the above steps.            stop the machine until visibility is restored.
          Use caution when loosening hydraulic
          connections.                                        Do not work below or behind a forwarder parked
                                                              on a grade.
       ENGINE
       HOOD                                                   When working on slopes, travel straight up or
                                                              down the slope to prevent roll-over.
    BATTERY
                 ••                                           NEVER travel across a STEEP slope or side hill:
    DISCONNECT
    SWITCH                                                    •    If you travel across a MODERATE slope,
                                                                   NEVER make an uphill turn as this could
                          ••                                       cause a tip-over situation.
                                                              •    When loading, keep load in grapple low and
                                                                   close to the forwarder for best stability.
    1055-009
                                                              •    A load of logs will change the handling and
                                                                   stability of the forwarder.
•      Turn the battery disconnect switch off if the
       vehicle is to be parked for an extended period         •    Always be prepared to dump the load in the
       of time (Example - overnight).                              grapple in case of emergency.
                                                              •    Never approach an unstable log from the
                                                                   downhill side.
                                                              •    Do not overload your forwarder as this can
                                                                   create an unstable condition and cause a
                                                                   roll-over.

                                                                                    CAUTION
When the engine is running, DO NOT allow                          Do not open cab doors or window screens
anyone in areas of the machine where they may                     (if equipped) when machine is on a slope.
be crushed by moving components.                                  The doors and screens are heavy and could
                                                                  swing out with considerable force.
                                                        1.7

--- Page 4 ---
Tigercat 1045/1055 Forwarder
Tigercat 1045/1055 Forwarder                                                                            Lubrication and Maintenance
SECTION 3 - LUBRICATION & MAINTENANCE
                                                                                                                                           AUGUST, 2006

Read and understand the entire manual including Safety section prior to operating any equipment.
Read and understand all manuals for any attachments or accessories.

CONTENTS - SECTION 3
AIR CLEANER
  CHANGING FILTER ELEMENTS ................................................................... 3.17
  MAINTENANCE .............................................................................................. 3.16
  SERVICING ..................................................................................................... 3.17
  UNLOADER VALVE ........................................................................................ 3.16
AIR CONDITIONING ........................................................................................... 3.18
ARTICULATION JOINT ....................................................................................... 3.15
AXLE LUBRICATION .......................................................................................... 3.25
BELT - ENGINE SERPENTINE .......................................................................... 3.26
CAB
 LOWERING THE CAB .................................................................................... 3.21
 RAISING THE CAB ......................................................................................... 3.20
CAB AIR FILTERS
 FRESH AIR ..................................................................................................... 3.19
 RECIRCULATING AIR - A/C UNIT .................................................................. 3.19
CENTRE JOINT ........................................................................................ 3.14, 3.15
CHARGE PRESSURE FILTER-DRIVE PUMP ................................................... 3.13
CONTROL POD ON ARMREST, R.H.
CRANE, ROTATOR AND GRAPPLE MAINTENANCE ....................................... 3.27
DRAINING AND REFILLING BOGIE HOUSING ................................................. 3.26
DRAINING AND REFILLING DIFFERENTIAL .................................................... 3.25
ENGINE HOOD ................................................................................................... 3.22
ENGINE SERPENTINE BELT ............................................................................. 3.26
FILTERS
  CHARGE PRESSURE .................................................................................... 3.13
  FUEL FILTER/WATER SEPARATOR ............................................................. 3.10
  HYDRAULIC OIL ............................................................................................. 3.12
  REMOVE AND REPLACE ............................................................................... 3.10
  RETURN OIL STRAINER ................................................................................ 3.14
  SERVICING GUIDELINES FOR OIL FILTERS ............................................... 3.13
FIRE PREVENTION .............................................................................................. 3.4
FUEL TANK STRAINER ..................................................................................... 3.11
GENERAL ............................................................................................................. 3.4
HOT WATER SHUT OFF VALVE ....................................................................... 3.18
HYDRAULIC OILS ................................................................................................ 3.7
INITIAL PRE-DELIVERY INSPECTION ................................................................ 3.3
LINK SNUBBER MAINTENANCE ....................................................................... 3.27
MACHINE STARTUP .......................................................................................... 3.24
NEW MACHINE MAINTENANCE ......................................................................... 3.3
OSCILLATION JOINT ......................................................................................... 3.15
PREVENTIVE MAINTENANCE SCHEDULE ........................................................ 3.3


                                                                                                                            continued...

                                                                              3.1

--- Page 5 ---
Tigercat 1045/1055 Forwarder                                                 Lubrication and Maintenance

                      IMPORTANT                                                  FILL
                                                                                 CAP &
                                                                                                       ••
  Filters that are an integral part of the engine
                                                                                 TUBE
                                                                                                        •
  (fuel and lubricating oil) should be serviced
  and replaced according to the engine
  manufacturer’s operation and maintenance
  manual.
  Tier III engines typically use filters with a
  very fine micron rating. If the fuel supply is
  dirty, the fuel filter must be replaced more                                                                         FUEL
                                                                                                                       TANK
  frequently than recommended in the                                                                                   DRAIN
  owner’s manual. Operating the machine                                                           ••                   PLUG

  with a clogged fuel filter will result in low
                                                              1014-D016    FUEL TANK DRAIN PLUG
  engine power. It is also recommended that
  the fuel/water separator bowl be drained                                   DIPSTICK                       FILL CAP
  daily.
                                                                   •                         ••
  When installing a new fuel filter, DO NOT                               FILLER
                                                                          SCREEN                                  FUEL TANK
  pre-fill with diesel fuel, or engine fuel pump
  damage will result. This type of failure is
                                                                  •                     ••                        FILL SPOUT


  not warrantable by the engine manufacturer.
                                                                  •
                                                                                FUEL
                                                                              SHUT-OFF
                                                                                                       ••
  To prolong the operating life of the fuel filter,                            TURNED
  ensure that the fuel supply storage tank is                                  ON (UP)
  clean and free of water and that the fuel is
  pre-filtered prior to adding it to the machine.                                                            ••      FUEL TANK
                                                                                                                      COVER

FUEL TANK STRAINER
                                                                            1014-D064        FUEL TANK LOCATION
This is a stainless steel fuel strainer, screwed on to
the inlet pipe of the engine fuel feed line inside at    7. Reinstall the strainer using the hex on end.
the bottom of the fuel tank.
                                                         8. Reinstall fuel tank cover plate with new “O”
Changing or cleaning the strainer:                          ring.
1. Park machine on level ground, install                 9. Reinstall drain plug.
   articulation lock bar, lower the blade (if
   equipped) and place the crane in the park             10. Refuel and check for leaks. Start the engine
   position, stop engine, remove key, then switch            and check for leaks again.
   battery disconnect off, and block wheels.
2. Remove filler cap. Install a suitable container
   below fuel tank, remove drain plug and drain
   the fuel tank.
3. Remove the cover from the fuel tank and “O”
   ring from the access hole.
4. Clean any debris from the bottom of the tank
   and wipe it clean.
5. Remove the fuel strainer using the hex on the
   end of strainer. Carefully clean the strainer (it
   may be damaged by rough handling).
6. Check for a buildup of foreign materials where
   the strainer threads on to the pipe and elbow.


                                                       3.11

--- Page 6 ---
Tigercat 1045/1055 Forwarder                                             Lubrication and Maintenance
  PARTIAL TILT SUPPORT           SPRING                     NOTE: When the cab locking pins are seated in
  SUPPORT SLOT BOLT              LOCK
                                                            the locking plates, rotate the pins so the flat
                                                            surfaces of the locking pins are horizontal.
                            •   SUPPORT LINK

                     •   ••     IN PARTIAL TILT
                                POSITION.
            ••             •                                                    CAB LOCKING
                                                                                PINS
 LONG TERM
 SUPPORT (HOLE)
                                                                  ••                                    ••
                                                                  •               PIN LOCK
                                                                                  PLATES
                                                                                                        •
                 CAB TILT SUPPORT LINK IN                   1055-073     LEFT SIDE BELOW CAB
 1075-003         PARTIAL TILT POSITION
                                                            4. Place the locking plates back in the slots on
11. For partial tilt, lower cab all the way down, then         the locking pins and tighten the cap screws.
    raise the cab, as the cab is raised the support
    link will slide along the support bolt. When the        5. Place the cab tilt control lever in the LOWER
    link partial tilt slot is just over the support bolt       position and remove tilt pump handle.
    the link will begin to fall onto the support bolt.      6. Place the pump handle back in the storage
    At this point lower the cab until the support bolt         location.
    bottoms in the partial tilt slot of the support
    link.                                                   7. Close the left side hydraulic tank access door.

NOTE: When using the support link for partial tilt,
the support bracket bolt must be bottomed in the
partial tilt slot position of the support link.
LOWERING THE CAB
1. Clear the area under the cab and cab path of
   obstructions and secure all lines and wires.


                          CAUTION
 Keep hands away from the locking pin area
 as the cab is being lowered.

2. Place tilt pump control lever in LOWER
   position.
NOTE: If the cab is in the partial tilt position, the
cab must first be raised to the full tilt position to
release the support link. Then it can be lowered.
(Otherwise it will lock in the partial tilt position.)
3. Operate pump until the cab is all the way over
   in the ride position onto the locking pins.


                                                         3.21

--- Page 7 ---
Tigercat 1045/1055 Forwarder                                                                   Lubrication and Maintenance

Par
 arkker                                                                                           Assemb
                                                                                                  Assemblly Tor que
                                                                                                             orque
                     JIC 37 Degree Flare                                                                       NPTF
                                     Tube Connection   Swivel or Hose                                            Tube Connection       Swivel or Hose
SAE Dash Size     Thread Size        FFWR              Connection FFWR      SAE Dash Size     Thread Size        TFFT                  Connection TFFT
        -2              5/16-24              NA               NA                    -2               1/8-27              2-3                  2-3
        -3               3/8-24              NA               NA                    -3                 NA                NA                   NA
        -4              7/16-20               2                2                    -4               1/4-18              2-3                  2-3
        -5               1/2-20               2                2                    -5                 NA                NA                   NA
        -6              9/16-18             1 1/2            1 1/4                  -6               3/8-18              2-3                  2-3
        -8               3/4-16             1 1/2              1                    -8               1/2-14              2-3                  2-3
       -10               7/8-14             1 1/2              1                   -10               7/8-14              NA                   NA
       -12             1 1/16-12            1 1/4              1                   -12               3/4-14              2-3                  2-3
       -14             1 3/16-12              1                1                   -14                 NA                NA                   NA
       -16             1 5/16-12              1                1                   -16              1-11 1/2           1.5-2.5              1.5-2.5
       -20             1 5/8-12               1                1                   -20            1 1/4-11 1/2         1.5-2.5              1.5-2.5
       -24             1 7/8-12               1                1                   -24            1 1/2-11 1/2         1.5-2.5              1.5-2.5
       -32             2 1/2-12               1                1                   -32              2-11 1/2           1.5-2.5              1.5-2.5
       -40                3-12                1                1                   -40                 NA                NA                   NA

F.F.W.R : Flats From Wrench Resistance                                      T.F.F.T. : Turns from finger tight
All values are for Steel, Stainless Steel and Brass                         All pipe values are for Steel, Stainless Steel and Brass


                O'ring Face Seal / Seal-Lok                                                                    BSPT
                                     Tube Connection   Swivel or Hose                                            Tube Connection       Swivel or Hose
SAE Dash Size     Thread Size        FFWR              Connection FFWR      SAE Dash Size     Thread Size        TFFT                  Connection TFFT
        -2                NA                 NA               NA                    -2               1/8-28              2-3                  2-3
        -3                NA                 NA               NA                    -3                 NA                NA                   NA
        -4              9/16-18          1/4 TO 1/2       1/2 TO 3/4                -4               1/4-19              2-3                  2-3
        -5                NA                 NA               NA                    -5                 NA                NA                   NA
        -6             11/16-16          1/4 TO 1/2       1/2 TO 3/4                -6               3/8-19              2-3                  2-3
        -8             13/16-16          1/4 TO 1/2       1/2 TO 3/4                -8               1/2-14              2-3                  2-3
       -10               1-14            1/4 TO 1/2       1/2 TO 3/4               -10                 NA                NA                   NA
       -12            1 3/16-12          1/4 TO 1/2       1/3 TO 1/2               -12               3/4-14              2-3                  2-3
       -14                NA                 NA               NA                   -14                 NA                NA                   NA
       -16            1 7/16-12          1/4 TO 1/2       1/3 TO 1/2               -16                1-11             1.5-2.5              1.5-2.5
       -20            1 11/16-12         1/4 TO 1/2       1/3 TO 1/2               -20              1 1/4-11           1.5-2.5              1.5-2.5
       -24               2-12            1/4 TO 1/2       1/3 TO 1/2               -24              1 1/2-11           1.5-2.5              1.5-2.5
       -32                NA                 NA               NA                   -32                2-11             1.5-2.5              1.5-2.5
       -40                NA                 NA               NA                   -40                 NA                NA                   NA

F.F.W.R : Flats From Wrench Resistance                                      T.F.F.T. : Turns from finger tight
All values are for Steel, Stainless Steel and Brass                         All pipe values are for Steel, Stainless Steel and Brass


                                                                         3.31

--- Page 8 ---
Tigercat 1045/1055 Forwarder                Electrical & Computers
THROTTLE AND BRAKE FOOT CONTROL SCHEMATIC


1055-076


                               6.9

--- Page 9 ---
Tigercat 1045/1055 Forwarder          Electrical & Computers
XP2-A2 GRAPPLE MODULE SCHEMATIC


 1055-074


                               6.19

--- Page 10 ---
Tigercat 1045/1055 Forwarder                                               Electrical & Computers


                                                              CURRENT OUT


 1014-D121                                                1014-D121

                                                           Press F1 SELECT to display SELECT
    Press F1 SELECT (+) to select the BOOM UP
                                                           FUNCTION menu.
    function for adjustment. (NOTE: Pressing the
    F2 SELECT (-) selects the BOOM DOWN
    function.)


                                                                               MANUAL
     MIN CURRENT
     (+) MAIN BOOM
      OK       CANCEL
                        360mA


                                                          1014-D187

                                                           Operate the BOOM UP joystick to select it for
 1014-D121                                                 adjustment.
    Use the UP/DN buttons to select desired
    adjustment, Min Current, Max Current, Start
    Slope, Stop Slope or Fine Controls. See
    CURRENT OUTPUT SETTINGS
    DESCRIPTION in this Section.
    Shown above MIN CURRENT (+) MAIN
    BOOM UP function has been selected.

                                                          1014-D186
2. DIRECT SELECTION
                                                           (+) Main Boom appears in the display. Press
                                                           F1 “SELECT” to confirm selection of boom up.


 1014-D098

    Press F2 OUTPUTS to choose CURRENT                    1014-D134
    OUT menu.
                                                           Use the UP/DN buttons to select desired
                                                           adjustment, Min Current, Max Current, Start
                                                           Slope, Stop Slope or Fine Controls. See
                                                           CURRENT OUTPUT SETTINGS
                                                           DESCRIPTION in this Section.
                                                           Shown above MIN CURRENT (+) MAIN
                                                           BOOM UP function has been selected.


                                                   6.29

--- Page 11 ---
Tigercat 1045/1055 Forwarder                                                     Electrical & Computers
CONDITIONAL MESSAGES (CM)
Conditional messages give the operator
information regarding an event or problem
condition while the event or problem exists. If the
event or condition disappears, so will the
message and alarm.


                                                              1014-D164


                                                             2. CRANE START (CM)
                                                                 If any crane joystick input is high (joystick
                                                                 activated) when crane switch is turned on,
                                                                 Crane Input Is Active message is displayed.
                                                                 Release the joystick to deactivate the input to
 1014-D031
                                                                 operate the crane.
If the operator presses “OK” on the MDM, the
message will disappear even if the problem still
exists. When this alarm is activated investigate
the cause. Refer to ELECTRICAL AND
COMPUTER SECTION of Service Manual.


                                                             1014-D040

                                                             3. DRIVE START (CM)
                                                                 If the drive pedal input is high (pedal
                                                                 activated) before pilot is reset, Drive Pedal
                                                                 Input Is Active message is displayed. Drive is
 1014-D030
                                                                 prevented until the pedal is released.
                                                                 Release the pedal to deactivate the input to
1. SYSTEM BYPASSED WARNING                                       enable the drive function.
    When an alarm is bypassed, as long as the
    fault is still active, this warning will be
    displayed, alarm warning light will flash and
    horn will sound every 30 seconds.
    When this alarm is activated investigate the
    cause immediately. Once the fault is fixed,
    warning deactivates and bypass is stopped.


                                                      6.39

--- Page 13 ---
Tigercat 1045/1055 Forwarder                                          Electrical & Computers

FUSE AND RELAY PANELS


                              FUSE AND RELAY PANEL LABEL- UNDER CAB


2. FUSE AND RELAY PANEL - UNDER CAB


1065-001


    Fuses and relays for the engine, hydraulic
    and machine electrical controls are located in
    the electrical box under the cab.


                                                     6.49

--- Page 14 ---
Tigercat 1045/1055 Forwarder                                                 Electrical & Computers
8. In the IQANdevelop main screen, select the              7. Open the new application in IQANdevelop
                                                              G3 on the computer.

              icon.


9. This will display a new dialog box titled
   ‘Receiving…’, and the download process will
   begin.
10. Once the download process is complete, the
    PDA display will return to the main
    IQANdevelop G3 window. The downloaded
    application description will replace the <empty
    slot> in the top right corner of the PDA.
    Important: The download process should take
    less than one minute to complete. During this
    time, do not perform any other functions on the        8. A dialog box titled ‘Enter application code’
    PDA, or turn off power to the MDM. DO NOT                 will appear. Enter the correct application
    START THE MACHINE. Should this occur, the                 code and select the ‘OK’ box. Note:
    download will be halted and incomplete;                   contact the Tigercat Customer Service to
    starting from the beginning will be required.             acquire the correct application code.
B. GET APPLICATION USING A                                 9. Using the drop-down menus: select
      A PC/LAPTOP                                             ‘System’, ‘Get application’
    The following procedure instructs how to
    retrieve a Tigercat IQAN application with a
    personal computer (PC), or laptop from the
    MDM (Master Display Module).
    To perform this procedure you will require:
    •   PC/Laptop
    •   IQAN data cable for PC/Laptop (no adapter
        cable required)
    •   Hardware key (Parker IQAN component
        available from Tigercat)
    1. Park machine on level ground, lower all
       implements to the ground, set the park
       brake ON, and turn the key switch to OFF.
                                                           10. Choose a filename and the location you
    2. Locate the ‘round’ RS232 port connection               wish to save the file. Click on Save.
       on the back of the MDM. Do not
       disconnect the rectangular 6-pin
       connector.
        Note: This will require temporary removal
        of the MDM from its mounting location (4
        screws).
    3. Remove the rubber dust seal from the
       RS232 port and connect IQAN data cable
       for PC/Laptop.
    4. Connect the other end of the cable to the
       COM1 serial port on the PC/Laptop.
    5. Turn on power to the computer, and start
       the IQANdevelop G3 program.
                                                           11. A pop-up box will confirm that the file is
    6. Turn the key switch to ‘RUN’. DO NOT
                                                               being downloaded.
       START THE MACHINE.
                                                    6.59

--- Page 15 ---

View the complete manual on HeyDownloads →