PDF Service Manual Suzuki GS500E Twin (1989-1997) - 8 MB

This is a comprehensive service and repair manual for the Suzuki GS500E Twin motorcycle, covering models from 1989 to 1997.

It offers detailed instructions for everything from routine maintenance to a full engine rebuild.

The manual includes wiring diagrams, specifications, and clear illustrations to guide you through every process.

It's an essential resource for both professional mechanics and DIY enthusiasts.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 3 ---
0-10     Daily (pre-ride) checks
1 Engine/transmission oil level
Beforeyou start
tI' Take the motorcycle      on a short run to
allow it to reach normal operating temperature.
Caution: Do not run the engine in an
enclosed$pacesuch as a garageor
~.
tI' Stop the engine and place the motorcycle
on Its centre       stand. Allow  it to stand
undisturbed for a few minutes to allow the oil
level to stabilise. Make sure the motorcycle is
on level ground.

Bike care:                                           1 Unscrewthe oil filler cap from the right- 2         Using a clean rag or peper towel, wipe off
.    If you haveto add oil frequently.you               hand side crankcasecover.The dipstick              all the 011from the dipstick, then Insert
should check whether you have any oil leaks.            is integral with the oil filler cap, and is        the clean dipstick back into the engine,
If there is no sign of oil leakage from the joints
                                                     usedto check the engineoil level.                but do not screw It In.
and gaskets the engine could be burning 011
(see Fault finding).


                                                     3   Remove the dipstick and observe the          4    If the level is below the 'L' line, top the
                                                         level of the oil, which should be                 engine up with the recommended grade
                                                         somewhere In between the upper 'F' and            and type of oil, to bring the level up to
                                                     lower 'L' level lines (arrows).                  the 'F' line on the dipstick.


2 Battery electrolyte level
           Warning: Be extremely careful             Before you start:                                Bike care:
    .&.    when handling or working
           around the battery - the
           electrolyte Is very caustic.
                                                     tI Position the motorcycle on its centre
                                                     stand on levelground. Removethe seat (see
                                                     Chapter7) for accessto the battery.
                                                                                                      .   If the battery electrolytelevel needs
                                                                                                       toppingup frequently.it Is likelythat thereis a
                                                                                                       problem either with the battery or with the
                                                     tI Use distilled water to top up the battery.     charging system. Refer to Chapter 8 and
                                                     Do not usetap water(ex~ I.nan ern~.              investigatethe problem.


                                                                                                           . . . and fill each cell to the MAX !evelline
1    The electrolyte level is visible through the
     translucent battery case - It should be         2 IfbeRemove
                                                            the electrolyteis low the battery must
                                                              topped up with distilled water. 3
                                                                   the cell caps. . .
                                                                                                           with distilled water - do not overfill. On
                                                                                                           completion, mop up any spills and install
     between the upper MAX and lower level
lines (arrows).                                                                                       the cell caps.

--- Page 4 ---
1-8    Every 4000 miles (6000 km) or 12 months


9 Using your fingers, turn the cam follower of    IlIu8tr8tions). The shim size should be             Obtain and install the replacement shim,
the valve In question so that Its shim removing   stampedon its face(... IIlu8tr8tion).A shim         notingthat its sizemarkingshouldbe Installed
slot faces backwards (exhaust valve) or           size of 250 denotes a thickness of 2.5 mm,          downwards and that the shim should be
forwards (intake valve) (... 11I\I8tI'8tIon).     245 is 2.45 mm. It is recommended that the          lubricated with engine 011.
10 Fit the tool under the camshaft, making        shim is measured to check that It has not           13 Removethe tool from the follower.Rotate
StKe it contacts only the follower and not the    worn (Me -..ti       o).ShIma ~ avaI~      in       the crankshaftseveralturns to seat the new
shim, and pre.. it down to depress the            0.05 mm Increments from 2.15 to 3.10 mm.            shim. Checkthe clearanceagain,then repeat
        .                                         12 Using the shim selection chart, find where      the process for any other valves until the
11 PrIM the shm out of the foIower ~     a        the measured valve clearance and existing           ct.'8nCe8 are correct.
small screwdriver inserted In Its slot and        shim thickness values intersect and read off        14 Install all disturbed components in a
remove it using a pair of pliers (...             the   shim   size   required   (...   IIlustr8t1on).r8o.wseof the rwnovaI8eCJIBnCe.

--- Page 5 ---
1-18       Non-scheduled maintenance


           25.5 Removethe vacuum take-off C8p(arrow)                                    25.8 Catb~or       syndvonisatlon    8CNW (arrow)


must be replaced.Notethat in very~ c-.           synchrmslng    the C8burettors, m8ce atn the           8 The carburettors are adjusted by turning
the fault could lie in the carburettors rather   valve Cleerances are properly set.                     the synchronlslngscrew situated In-between
than the cable, necessitatingthe removalof       2 To properly synchronlse the carburettors,            the carburettors, in the throttle linkage (see
the carburettorsand inspectionof the choke       you win need some sort of v.:wm    gauge set-          illustr8tion). The screw Is accessedusing a
valves(see~..        3).                         up with a gauge for each cylinder, or a                long screwdriver. Turn the screw until the
                                                 manometer, which is a calibrated tube                  readingon each gaugeIs the same.Note: Do
                                                 arrangement that utilises columns of mercury           not p~ down on the screw whilstadjusting
                                                 or steel rods to indicate engine vacuum. If            It, otherwisea false readingwill be obtained.
                                                 using      a    m.-cury      manometer,        extra   When the carburettors are synchronlsed,
                                                 precautions      must be taken during use and          open and close the throttle quickly to settle
                                                 storage of the instrument        as mercury Is a       the linkage,and recheckthe gaugereedings,
                                                 liquid, and extremely toxic. Because of the            readjustingIf necessary.
Note: T1Je carbu,.uors       will go out of                                                             8 Whenthe adjustmentis ~ete,           recheck
                                                 nature of the synchronlsation       procedure and
synchronlsation over 8 period of time,                                                                  the vacwm readings, then adjust the idle
                                                 the need for special Instruments, most 0WI'*8
resulting In decf88sed fuel mileage, Increased                                                          speed by turning the throttle atop screw until
                                                 leave the task to a Suzuki dealer.
engine temperature, less than Ideal throttle                                                            the Idle speed listed In this Chapter'.
                                                 3 Start the engine and let It run until It reaches
response and higher vibration /e~.                                                                      Specificationsis obtained.
                                                 normal ~ng           tempereture, then shut It off.
 .&.       Werning:    Petrol  (ga.ollne)   ,.                                                          10 Stop the engine. Remove the gauge
                                                 4 ~           the fuel tank (s. Chapter 3).
           extremely   flammable,     .0 take                                                           hosesand replacethe take-off caps. Detach
       .   extra precautionswhen you             5 Remove the vacwm take-off cap from the
                                                                                                        the temporaryfuel supply Md install the fuel
                                                 top of each carburettor        (8.. IlIu8tratlon).
           worlc on any part of the fuel                                                                tank (seeChapter3).
                                                 Connect the gauge hoses to the take-off
system. Don't smoke or allow open frames
                                                 adapt«s. Make S(Q there .-e no air leaks as
or bare light bulbs near the worlc area, and
                                                 false reedings will ~It.
don't worlc in a garage where a natural
                                                 8 Arrange a temporary fuel supply, either by
gas-type appliance Is present. "you spill
any fuel on your skin, rinse it off              using a small temporary tank or by using extra
immediately with soap and water. When            long fuel pipes to the now remote fuel tank.
you perform any kind of work on the fuel         Alternatively.   poeitIon the tank on a suitable  Note: An improperlyadjusted headlightmay
system, wear safety glassesand have a fire       base on the motorcycle,        taking care not to cause problems for oncoming traffic or
extinguisher suitable for a Class B type fire    scratch any paintwork, and making sure that       provide poor, unsafeilluminationof the road
                                                 the tank Is safely and securely supported.        afield. Seforaadjustingthe hMcI#ght8m, be
 .&.
(flammable liquids) on hand.
           Warning: Take great care not to       7 Start the 8ngN 81d ~            the lcIe speed  sure to consult with local trafflc laws and
     ,
       .   burn your hand on the hot
           engine unff when accessing the
          gauge take-off points on the
                                                 to 1750 rpm using the throttle stop screw
                                                 under    the right-hand      carburettor     (...
                                                 11IU8tr8t1on 8.3). If the gauges are fitted with
                                                                                                   regulations. For UK models, refer to 'MOT
                                                                                                   TestChecks'in the Refetencesectionon this
                                                                                                   Manual.
intake manifolds. Do not allow exhaust           dampingadjustment.set this so that the 1 The headlightbeam C8I be adjusted both
gases to build up In the worlc .rea; either      needle flutter is just eliminated but 80 that horIzontally~ vertic81y.Checkftm that the
perform the ChKk outside or use an               they can stili respond to small changes in tyre preeaur88are correct and the IUSpension
.m.ust gas utractlon system.                     pressure.Thevacuumreadingsfor both of the is adjustedas~ulred. The machinemust be
1 Carburettor synchronisation is simply the      cylindersshould be the same. If the vacuum off its stand 81d on levelground,with the fuel
process of adjusting the carburettors so they    readingsVaIY.proceedas follows.                   tank half full and with an assistantsitt'ng on
pass the same amount of fueVair mixture to       Caution: Do not .llow th. engine to the seat. If the bike Is usually ridden with a
each cytinder. This Is done by measuring the     overiIHt "n8C8a8ry, stop the engine end passenger on the back, have a second
vacuum produced In each cylinder. Before         allow It to cool b8foN starting 8g8/n.            assistantto do this.

--- Page 6 ---
2-6 Engine, clutch and transmission


    5.10 Pull back the rubber cover (arrow) and disconnect the
         starter motor lead from Its terminal on the relay


releasing it from Its clamp on the frame tube.       or ties, noting its routing, and coil it on top of   pan) (S88 Illustration).   Make sure the jack is
Peel back the rubber cover from the relay,           the crankcase so that It does not Impede             centrally positioned     so the engine will not
then unscrew the nut securing the cable to Its       engineremoval.                                       topple when the last mounting bolt Is removed.
terminal and disconnect the cable (see               18 Tracethe neutralswitch wiring back from           Take the weight of the engine on the jack.
IlIu8tr8tion). Pull the cable back to the starter    the top of the sprocketcover and disconnect          18 Unscrew the nuts on the six bolts which
motor, noting its routing, and coil it on top of     it at its connector.Releasethe wiringfrom any        secure the right-hand side frame downtube to
the crankcase so that it does not impede             clips or ties, noting its routing, and coil it on    the rest of the frame. then withdraw the bolts
engine removal.                                      top of the crankcase so that it does not             (see Illustrations).
                                                     impedeengineremoval.                                 19 Unscrew the nuts on both the upper and
11 Unscrew the gearchange lever pinch bolt
and remove the lever from the shaft, noting          17 At this point, position an hydraulic or           lower front engine mounting      bolts, then
any alignment marks on the lever and the             mechanicaljack underthe enginewith a block           remove the right-hand side frame downtube
                                                     of wood betweenthe jack headand sump (oil            (see Illustrations). Remove the spacers from
shaft (see lIustration). If no marks are visible,
make your own before removing the lever so
that it can be correctly aligned with the shaft
on installation.
12 Remove the front sprocket (Chapter 5).
13 Remove the exhaust system (Chapter 3).
14 Trace the ignition pulse generator and oil
pressure switch wiring back from the base of
the right-hand side crankcase cover and
disconnect it at its connector. Release the
wiring from any clips or ties, noting Its routing,
and coil it on top of the crankcase so that it
does not Impede engine removal.
 16 Trace the alternator wiring back from the
top of the sprocket cover on the left -hand side
of the engine and disconnect it at its bullet                                                              5.18a Right-hand side    frame   downtube   is
                                                                                                          secured by two bolts at the rear (arrows). . .
connectors. Release the wiring from any clips


                                                      5.19a Unscrew the front engine bolt nuts
                                                                       (arrows)   ...

--- Page 7 ---
the nuts evenly and a little at a time in a        12 Fit a new O-ring onto each cylinderhea:d      14 Carefullylower the cylinderhead over the
reverse of their numerical sequence until they     stud and press it into its recessin the top of   studs and onto the block (see illustration). It
are all slack. Remove all the nuts and their       the cylinder block (see illustration). Check     is helpful to have an assistant to pass the
washers, taking great care not to drop any of      that they are properlyseated.                    camchain up through the tunnel and slip a
them into the crankcase. Discard the washers       13 Ensure the cylinder head and block            piece of wire through it to prevent It falling
as new ones must be used.                          mating surfaces are clean, then lay the new      back into the engine. Keep the chain taut to
6 Pull the cylinder head up off the studs. If it   head gasket in place on the cylinder block,      prevent It becoming disengaged from the
is stuck, tap ~round1he joint faces of the         makingsure all the holesare correctlyaligned     crankshaftsprocket.
cylinder head with a soft-faced mallet to free     and that the UP letters stamped out of the       15 Install the eight domed nuts using new
the head. Do not attempt to free the head by       gasket read the correct way round (He            washers and tighten them finger-tight (...
inserting a screwdriver between the head and       Illustrations). Neverre-usethe old gasket.       illustrations).
cylinder block - you'll damage the sealing
surfaces.
7 Lift the head off the block, and remove it
from the engine. Remove the old cylinder
head gasket and the O-rings which fit around
the cylinder head studs (see Illustration).
Stuff a clean rag into the camchaln tunnel to
prevent any debris failing Into the engine.
Discard the gasket and O-rings as new ones
must be used.
8 If they are loose, remove the two dowels
from the cylinder block studs (see illustration
11.7). If eIther appears to be missing it is
probably stuck in the underside of the cylinder
head.
                                                                                                         11.13a Fit the new cylinder head
9 Check the cylinder head gasket and the                                                                             gasket...
mating surfaces on the cylinder head and
block for signs of leakage, which could
indicate warpage. Refer to Section 13 and
check the flatness of the cylinder head.
10 Clean all traces of old gasket material
from the cylinder head and block. If a scraper
is used, take care not to scratch or gouge the
soft aluminium. Be careful not to let any of the
gasket material fall Into the crankcase, the
cylinder bores or the 011pa8$8ges.


Installation
11 If removed, install the two dowels onto the
cylinder   block   studs   (see Illustration).        11.13b... makingsurethe UPmark                       11.14 Lowerthe cylinder heed
Lubricate the cylinder bores with engine oil.              (arrow)readscorrectly                                  onto the block

--- Page 8 ---
2-26 Engine, clutch and transmission


                                                                                                17.3 The crankcase cover is secured by
                                                                                               thirteen bolts (arrows).Note the positions
                                                                                               of the wiring clips on three of the bolts (A)


 17.4 Note the positions of the two dowels
(an'Ows) and remove them if they are loose

hand side crankcase cover (see illustration).
Remove the COY«. Using a 19 mm spanner to
counter-hold the tflnlng rotor, unscrew the bolt
in the centre of the rotor which secures it to the
end of the crankshaft (s.. illustration).
Remove the rotor, noting how the pin In the
end of the crankshaft ~es        in the slot In the
rotor. The pulse ~r         coil assembly and oil
pressure switch can remain In the crankcase
cover, but the wiring must be disconnected at
its connector behind the left-hand side panel
and released from any clips or ties to enable
the cover to be moved away from the machine.
3 Working in a criss-cross pattern, evenly
slacken the right-hand side crankcase cover
retaining bolts, noting the position of the cable
clips (see Illustration). Ufl the cover away
from the engine, being prepared to catch any
residual oil which may be released as the
cover Is removed.
4 Remove the gasket and discard It. Note the
positions of the two locating dowels fitted to
the crankcase and remove them for safe-
keeping If they are loose (8M illu8b'8tion).
5 Working In a criss-cross pattern, gradually
and evenly slacken the clutch pressure plate
retaining bolts until spring pressure Is
released (see illustrations). To stop the
clutch from turning while Initially loosening the
bolts, either put the engine Into gear and have       1 Pressureplate bolt 7 Pushrodend piece 13 Outerthrostwssher18 Innerthrostwaher
                                                                           8 Frictionplates '. 14 Clutchhousing   19 Pu8hrods
an assistant apply the rear brake (If the engine      2 Spacer
is In the frame), or jam the primary drive and        3 Spring             9  Pls/nplates      15 PIn             20  Pushrodoil s8&I
driven gears together using the blade of a            4~p/8te              10 Clutchnut        16 ONpump drfVegesr2'1 RetaInerpIete
large screwdriver (If the engine has been             5 ThnIstwasher       11 LocIcwasher      17 Cftdfp          22 R-..   ~
removed). Remove the bolts, spacers and               6 R8#88Sebesrlng     12 Clutchcentre

--- Page 9 ---
2-36 Engine, clutch and transmission


                                                                                 2O.11cThe                                      ! as shown


M88mbly    onto the crankcase, positioning the   from the top of the engIM sprocket00Y8'and       4 Withdraw the starter idle/reduction gear
stopper arm roller onto the neutral change pin   disconnectIt at the connectors.Releasethe        shaft then remove the gear, noting which way
and hooking the return spring Into the hole in   wiringfrom any clips or ties.                    round It fits (8M IIkJsb'8tlon). Remove the
the input shaft bearing retainer plate (...      2 Unscrew the gearchangelever pinch bolt         att.-nator rotor (see Chapter 8). The starter
~          at. Tighten the bolt securety. Make   and remove the lever from the shaft, noting      driven gear shOI.Adcome away with the rotor. If
sure the stopper arm Is free to move and Is      any alignment marks on the lever and the         it doesn't, remove it from the crankshaft. The
returned by the presaure of the spring.          shaft (8M lIu8tr8tlon 18.18).If no marksare      starter clutch Is secured to the back of the
12 Install the engine sprocket cover and         visible, make your own before removingthe        rotor by thrM Allen bolts (..Ih8Ir.~.;.
tighten Its screws securely. Install the         lever so that it can be correctly aligned with
gearchange !eYeronto tt1e end of tt1e shaft on   the shaft on Installation. Unscrew the bolts     Inspection
the left-hand side of the engine, alignIng the   securing the engine sprocket cover to the        5 Install the starter driven gear into the starter
punch mart<8on the arm and shaft, and check      crankcase and move the cover aside (see          clutch (If removed) and, with the rotor face
that the ~Ism         ~      correctly. ~M       ~~uOHi 18.1bt.Thereis no needto detach           down on a workbench, check that the gear
                                                 the clutch cable from the cover. ReIeesethe      rotates freely in an anti-clockwise direction
                                                 alternator wiring from the clamp next to the     and locks against the rotor in a clockwise
                                                                                                  direction. If it doesn't, replace the starter
                                                                                                  clutch.
                                                                                                  e Withdraw the starter driven gear from the
                                                                                                  starter clutch. If it appears stuck, rotate it antl-
                                                                                            to    clockwise as you withdraw It to free it from the
                                                                                                  starter clutch. Ch~k the bearing surface of
Note: The starter clutch and Idle gear                                                            the starter driven gear hub arxj the condition
assembly can be removed with the engine In                                                        of the rollers inside the clutch body (...
the frame.                                                                                        Illustrations). If the bearing surface shows
                                                                                                  signs of excessive wear or the rollers are
Removal                                                                                           damaged, marked or flattened at any point,
1 Remove the left-hand side panel (see                                                            they should be replaced.
Chapter 7). Trace the alternator wiring back                                                      7 Remove the rollers and check the plungers


21.3

--- Page 10 ---
2'46 Engine,clutchandtransmission


Output shaft                                     a Inspectthe dogs and the dog holesIn the            and the spacer(see ilklStratlon).If one is not
  .                                              gears for cracks, chips. and excessivewear           available,carefullyleverthem off using a pair
Disassembly                                      especiallyin the form of roondededges.Make           of tyre levers(8M HkJStratIon-'1:1»). Install
21 Removethe needlerollerbearingfrom the         sure mating gears engageproperly. Replace            the bearing using a press. Install the needle
right-handend of the shaft (lee ilklSb'ation).   the pairedge.-s as a set if necessary.               mi. bearingonto the shaft, and check It fa
22 Removethe thrust washerfrom the right-        00 Checkfor signsof scoringor bluingon the           play or roughness.Replacethe bearingif It is
hand end of the shaft, then slide the 1at gear   ~k)ns. bushand shaft.ms ~         be caused          wa'n or damaged.
pinionand the 5th gearpinionoff the shaft.       by overtleatingdue to Inadequatelubrication.         34 Check the washersand replaceany that
ZJ Removethe clrdip s«:uring the 4th gear        Checkthat all the ~ holes ~ ~           are          are bent or appear weakened or worn,
pinion.then slide the spiinedwasherand the       clear.                                               DIscardall the circlips as new ones must be
pinionoff the shaft.                             31 Check that each pinion moves freely on            used.
24 Slide the two lockwashersoff the shaft,       the shaftor bush(2ndgear pinion)but without
noting how they fit, followed by the 3rd gear    unduefreepiay.Checkthat the 2nd gearbush
pinionarxjthespiinedwasher.                      moves
                                                     freelyontheshaft00twithoutundue
25 Removethe clrclip securingthe 6th gear freepiay,
pirjoo, ttMJ'1
             Pde the pirQ! off the shaft.  32 The shaft is unlikely to sustain d.a"'age
. Removethe Circlipsecuringthe 2nd gear unless the engine has seized, placing an
pinion,then slKiethe 2nd gear bush and the unusuaIly,highloadingon the msmission. or
pinionoff the shaft,                       the machinehas covereda very high mileage.
                                           Check the surface of the shaft, especially
Inspection                            wherea pinionturns onit. andreplace          the
27 Washall of the components in clean shaft If It has scored or picked up. or if there
solventanddrythemoff.                 areanycracks.
. Checkthe gearteethfor cracking33 Checkthe ball bearingfor playor
chipping, pitting and other obvious wear or      roughness,and that it is a tight fit on the shaft.
d8nage. Any pinionthat is dsnaged as such        Replace the bearing if it is worn, loose or          ~.33 Use a puller and draw the spacer off
must be replaced.                                tiom'anM linin 1             -"      .          .

--- Page 11 ---
Engine.clutchandtransmission


                                                   3O.23b ... making sure the tab locates in the notch (arrow),
                                                                and lubricate them generously


                                                                       not removethe bolts from the connecting
                                               -
                         31 Connecting rods removal,            .:1\
                                                                       rods.Keepthe rod,cap.nutsand(iftheyare
                            inspectionand installation          ~      to be reused)the bearingshellstogetherIn
                                                               ~       their correct positionsto ensurecorrect
                                                               ~       installation.
                        Note:To removethe connectingrods the Inspection
                                                          5 Check the connectingrods for cracks and
                        the crankcasesseparated.
                                                          otherobviousdamage.
                                                          6 If not alreadydone (see Section 15),apply
                                                          cleanengineoil to the piston pin, insertit into
                        1 Remove
                               thecrankshaft
                                          (seeSection29).
                                                          the connecting rod small-end and check for
                                                 from the
                                                          any freeplay between the two (see illus-
                                                          tration).Measure  the pin external diameter
                                                          andthe small-endborediameterand compare
                                                          the measurements  to the specificationsat the
                                                          beginning of the Chapter (seeillustrations
                                                               and 15.13band 15.13d).Replacecomponents
                                                                       that areworn beyondthe specifiedlimits.
                                                                       7 If the side clearance measured in Step 2
                                                                       exceedsthe service limit specified, measure
                                                                       the width of the connectingrod big-end and
                                                                       the width of the crankpin (see illustrational.
                                                                       Comparethe results to the specificationsat
                                                                       the beginning of the Chapter, and replace
                                                                       whichever component exceeds those
                                                                       specifications.

--- Page 12 ---
(e) tel tOI!d '(V) tel u!ew S"L
                                                              (MOJJe) .e)j:>os ~! JO .no
                                                        AIQwesse .eoIJ 84. Ull AtI"J8Je:)          8L" L
6uOIB M9J:>S .Ol!d 94. 9AOW9J pUB MeJ:>SUn                                    '(UOI~4Snll!                   pUB JOU9JnqJe:> 9~~ ~O esBq 9~~ O~ J9qWB~:>
                                                 &&.) tel U!SW e4t ehOWeJ pus MSJ:>SUn9                      ~BOI~ 9~~ 6u!Jn:>as SM9J:>S 9~~ M9J:>SUn 9
'(IU'H seuMH 998) peqJn~S!p eq II!M 6U!Ues S.!
~B4.e.ou ~nq.JOU9JnqJB:> 94~ WOJ. peAOWSJ                                   'pesn aq tsnw                                                          "U! pe"U S!
                                                                                                             d!l:l-3 a4~ ~:I~OU ~:>!~M 9~OU 'alpeeu 9~~ WOJj
sq UB:> MSJ:>S ~Ol!d S4~ 'SlepOw ~n UO 1-1- suo Meu S se 6uIJ-O e4} pJs:>S!Q'(uo!~~nll!                      p9/10W9J 9JB A8~~ ~I .Ja~seM pUB d!l:l-3 '~89S
                              .(SoL uOI~~nIH &&.) 6u!J-O St! pus tees shieh elpeeu
                                                                                                             6UIJdS 94t aSOI O~ ~OU9m:> 9)fBl "(UOAeJlSRIII
...) ~er ~Ol!d 94. SAOW9J pUB M9J:>SUn 01- teou e4} ehowe~ '(uo!lB.q8nlll ees) stJ~t! MO4
                 9P!n6 84~ WOJJ~! 9AOWSJ pUB 6u!toU leol~ elIt uo qBt e4t wOJJehlsh elpeeu                   ees) do~ 94~ WOJ~~! MBJp~~IM pUB UO~S!da~~
                                                 e4t )jOO4Un 'pesn eq tsnw QUOMeu e se t!                    ~O WOuoq 9~~ WOJ~dn alpeeu ~ar a~~ 4snd 9
WOuoq 94~ WOJJdn t9! elp&eU 94~ 4Snd .pesn
sq tSnW SUO MSU B SB sp!n6 S4t JO WO~toq         pJB:>S!Ppus 6uIJ-O e4t ehowe~ '(uO!~84Snll!                                     "pe8ewep
e4~ uo 6U!J-O e4~ pJB:>S!O .hpOq JOUSJnqJB:>     ..s) St!J t! MO4 6u!tou .ApOq JotteJnqJe:> A"1I5ee 5! Jf s~ w8eJlld~!p     .IIJ 83e/ds!p
S4~ O~UIS~USPln6 e4t punOJ hBM 4:>14M S~ON                                                   oJ JueWnJISUI dlells ~ esn Jou oa :UOlJnBo?
                                                 e4t Jo tno AIQWesseteolj e4t es!Jd AlinJeJsQL
iUO!~Snlll  .M) JOueJnqJB:> e4t .0 dOt 94.            'pesn eq tsnW euo Meu e ss t! pJs:>S!PpUB                         "(uo!l.4snlll    ees)
46noJ4. UMeJP4tIM aq MOU ue:> ~e! 9\pa9U pUB     te)jse6 JeqqnJ e4t ehOW9~ '(uOI~J~nlll ees) AlqwesSB UO~S!dpUB W6BJ~dB!P 94~ MBJP4~M

View the complete manual on HeyDownloads →