PDF Service Manual New Holland EC130 Crawler Excavator - 7 MB

This is the complete service manual for the New Holland EC130 Crawler Excavator.

It contains detailed, factory-approved procedures for repair and maintenance.

Technicians will find all the necessary information, including hydraulic schematics, electrical diagrams, and troubleshooting guides.

This manual is the definitive resource for keeping your EC130 excavator performing at its best.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram βœ‰Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
EXCAVATOR

                 E130


SERVICE
MANUAL
87360591 NA


Issued 01-2006


                    www.newhollandconstruction.com

--- Page 3 ---
SECTION 1 - STANDARD SPECIFICATIONS AND MAINTENANCE
                                  CHAPTER 1 - GENERAL INFORMATION AND SAFETY


CNH America, LLC reserves the right to make improvements in design or changes in specifications at any time without incurring any
obligation to install them on units previously sold.
All data given in this publication is subject to production variations. Dimensions and weights are only approximate. Illustrations do
not necessarily show products in standard condition. For exact information about any particular product, please consult your Dealer


                                                          Revision History
       Issue         Issue Date                Applicable Machines                                        Remarks
   First Edition       01-2006                         E130                                           5-1290 NA


1-II                                                                                 Issued 01-06   Bur                     5-1290 NA

--- Page 4 ---
SECTION 1 - STANDARD SPECIFICATIONS AND MAINTENANCE
                                     CHAPTER 1 - GENERAL INFORMATION AND SAFETY

 6. Unit Conversion

          QUANTITY                      GRAVITATIONAL                        SI                          CONVERSION FACTOR
             Mass                             kg                             kg
             Force                            kgf                             N                             1 kgf=9.807 N
            Torque                           kgfΒ·m                           Nm                            kgf m=9.807 Nm
           Pressure                         kgf/cm2                         MPa                      1 kgf/cm2=0.09807 MPa
        Motive Power                          PS                             kW                         1 PS=0.7355 kW
          Revolution                          rpm                           min–1                             r/min *1
 *1 Units that are allowed to use.


1-10                                                                                Issued 01-06   Bur                   5-1290 NA

--- Page 5 ---
SECTION 1 - STANDARD SPECIFICATIONS AND MAINTENANCE
                                 CHAPTER 2 - SPECIFICATIONS

2.2.2 TRANSPORTATION DIMENSIONS AND WEIGHT


CH02-06-01                                                                                   Figure 4


2-8                                                                  Issued 01-2006   Bur   5-1300 NA

--- Page 6 ---
SECTION 1 - STANDARD SPECIFICATIONS AND MAINTENANCE
                                 CHAPTER 2 - SPECIFICATIONS

2.4.1 ENGINE CHARACTERISTIC CURVE


CH02-16-01


2-18                                                                 Issued 01-2006   Bur   5-1300 NA

--- Page 7 ---
SECTION 1 - STANDARD SPECIFICATIONS AND MAINTENANCE
                           CHAPTER 3 - ATTACHMENT DIMENSIONS

3.2.2.2 CLEARANCE IN THRUST DIRECTION ON ARM AND CYLINDER INSTALLATION SECTION


CH03-08-01                                                                                   Figure 6

3-8                                                                  Issued 01-2006   Bur   5-1310 NA

--- Page 8 ---
SECTION 1 - STANDARD SPECIFICATIONS AND MAINTENANCE
                                                    CHAPTER 11 - TOOLS


CNH America, LLC reserves the right to make improvements in design or changes in specifications at any time without incurring any
obligation to install them on units previously sold.
All data given in this publication is subject to production variations. Dimensions and weights are only approximate. Illustrations do
not necessarily show products in standard condition. For exact information about any particular product, please consult your Dealer


                                                          Revision History
        Issue        Issue Date                Applicable Machines                                     Remarks
  First edition        01-2006                         E130                                           5-1320 NA


11-II                                                                                Issued 01-2006   Bur                   5-1320 NA

--- Page 9 ---
SECTION 1 - STANDARD SPECIFICATIONS AND MAINTENANCE
                                        CHAPTER 11 - TOOLS

11.5.2.4 PLUG FOR ORS JOINTS


CH11-08-01                                                                                    Figure 16


CH11-08-02                                                                                    Figure 17


11-10                                                                  Issued 01-2006   Bur   5-1320 NA

--- Page 10 ---
SECTION 1 - STANDARD SPECIFICATIONS AND MAINTENANCE
                           CHAPTER 11 - TOOLS


                 11.14 TRACK SPRING SET JIG


CH11-17-02                                                                       Figure 31


11-20                                                     Issued 01-2006   Bur   5-1320 NA

--- Page 11 ---
SECTION 1 - STANDARD SPECIFICATIONS AND MAINTENANCE
                      CHAPTER 12 - STANDARD MAINTENANCE TIME TABLE

12.2.4 TRAVEL SYSTEM, ELECTRIC EQUIPMENT


CH12-08-01                                                                                    Figure 5

12-8                                                                  Issued 01-2006   Bur   5-1330 NA

--- Page 12 ---
SECTION 1 - STANDARD SPECIFICATIONS AND MAINTENANCE
              CHAPTER 13 - MAINTENANCE STANDARDS AND TEST PROCEDURES


             13.2 PERFORMANCE INSPECTION STANDARD TABLES


CH13-04-01                                                                              Figure 1

13-4                                                              Issued 01-06   Bur   5-1340 NA

--- Page 13 ---
SECTION 1 - STANDARD SPECIFICATIONS AND MAINTENANCE
                          CHAPTER 13 - MAINTENANCE STANDARDS AND TEST PROCEDURES

13.6.1.1 PARKING BRAKE PERFORMANCE
 1. Confirm the parking brake holds when the
    machine is stopped in a no-load travel position
    on a 15 degree gradient slope.
 2. Place an angle meter on the shoe plate and
    confirm that it shows an angle of more than 12
    degrees. Hang a perpendicular rod parallel with
    the guide frame rib on the track frame. Put a
    matching mark on the shoe plate. Five minutes
    after the engine stops at park, measure the
    movement distance of the matching mark.


13.6.1.2 DRAIN RATE OF TRAVEL MOTOR
 1. Measure the drain rate of the travel motor and
    confirm the performance of the travel motor.
 2. Preparation:
    A. Apply stopper pins for both travel sprockets of
       left and right.
    B. Stop the engine, and release air in the
       hydraulic reservoir.
    C. Connect a hose to the drain port of travel
       motor and place in a container.
    D. Install a plug to the drain line at the tank side.

        WARNING: Make sure of the rotating
        direction of travel motor. Otherwise, rib β€œA”
        may be broken by the stopper pin.

 3. Measurement conditions:
  β€’ Engine: High Idle
  β€’ Hydraulic oil temperature: 45 to 55Β°C
     (113 to 131Β°F)
  β€’ Machine posture: Locked travel and over
     running the relief on the travel motor
 4. Measure the drain volume of oil for 30 seconds.
    Take three measurements in the forward motion
    o f e a c h s i d e a n d t a ke a n ave ra g e o f t h e
    measured value.
                                                                  CH13-14-01                           Figure 11


13-14                                                                             Issued 01-06   Bur   5-1340 NA

--- Page 14 ---
SECTION 1 - STANDARD SPECIFICATIONS AND MAINTENANCE
        CHAPTER 13 - MAINTENANCE STANDARDS AND TEST PROCEDURES


                                   NOTES


13-24                                                       Issued 01-06   Bur   5-1340 NA

--- Page 16 ---
SECTION 2 -HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                CHAPTER 21 - MECHATRO CONTROL SYSTEM


CH21-07-02                                                                       Figure 10

21-14                                                       Issued 01-06   Bur   5-1520 NA

--- Page 17 ---
SECTION 2 -HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                CHAPTER 21 - MECHATRO CONTROL SYSTEM


CH21-13-02                                                                       Figure 18


21-24                                                       Issued 01-06   Bur   5-1520 NA

--- Page 18 ---
SECTION 2 -HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                          CHAPTER 21 - MECHATRO CONTROL SYSTEM

21.2.6.1 GOVERNOR MOTOR (SYMBOL M-S)


CH21-18-02                                                                                 Figure 28

21-34                                                                 Issued 01-06   Bur   5-1520 NA

--- Page 30 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                              CHAPTER 24 - COMPONENTS SYSTEM

24.1.1.2 HYDRAULIC CIRCUIT DIAGRAM


C24-04-01                                                                                      Figure 2


24-4                                                                   Issued 01-2006   Bur   5-1380 NA

--- Page 31 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                                                    CHAPTER 24 - COMPONENTS SYSTEM


C24-14-01                                                     Figure 16
The feed back lever (611) is linked with the servo
piston and sleeve (651). As the servo piston moves
to the left, the feed back lever rotates on point A
which causes the sleeve to move to the right. As the
servo piston moves to the right, the feed back lever
rotates on point A to move the sleeve to the right.
This causes the spool sleeve opening to close
gradually and the servo piston settles down when the
opening of the spool sleeve closes completely.


FLOW DECREASE FUNCTION
As the command current I decreases, the secondary
p r e s s u r e o f t h e s o l e n o i d p r o p o r t i o n a l va l ve
decreases. This causes the spool to move to the left.
When the spool (652) has moved, delivery pressure
P1 reaches port Cl via the spool and is admitted to
the large diameter chamber of the servo piston.
Deliver y pressure P1 is admitted to the small
diameter section of the servo piston at all times. The
servo piston moves right to decrease the tilting angle
(a). As the servo piston moves to the right, the feed
back lever rotates on point A to move the sleeve to
the left. The sleeve will move until the opening of the
spool closes completely.


24-14                                                                                     Issued 01-2006   Bur   5-1380 NA

--- Page 32 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                                CHAPTER 24 - COMPONENTS SYSTEM

24.1.2.3 PILOT VALVE (TRAVEL)


CH24-25-01                                                                                      Figure 32

24-24                                                                    Issued 01-2006   Bur   5-1380 NA

--- Page 33 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                      CHAPTER 24 - COMPONENTS SYSTEM


CH24-35AF-02


24-34                                                          Issued 01-2006   Bur   5-1380 NA

--- Page 34 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                                       CHAPTER 24 - COMPONENTS SYSTEM


C24-34-01                                                                                                                Figure 49


24.1.8.0.2 FUNCTIONS FOR TRAVEL ACTION                         At the same time, the pressurized oil delivered by
Independent travel                                             pump (P2) passes between the outer circumference
                                                               of the left travel straight spool (306) and the casing
If forward travel is performed, the secondary pilot            and runs to port BL. This oil supplies the left travel
pressure from ports (2) and (4) of the travel pilot            motor (A) in the same way the pressured oil is
valve act upon ports PBr and PBL of the control valve          supplied to the right side travel motor.
and moves the right and left travel spools (306).
                                                               The oil which has returned from right travel A and the
The pressurized oil delivered by pump (P1) flows to            l e f t t r ave l B s i d e p a s s e s b e t we e n t h e o u t e r
the main passage (51) past the travel straight spool           circumference of the right and left travel spool (306)
(307) and passes between the outer circumference               and the casing from ports Ar and AL and returns to
of the right travel spool (306) and the casing. This           the hydraulic tank via the tank port (T) of the low
pressurized oil is supplied to the right travel motor B        pressure circuit (D).
by way of port Br.
                                                               The pressurized oil works the same way in reverse
                                                               as in forward (when the secondary pilot pressure
                                                               acts upon ports PAr and PAL of the control valve.

24-44                                                                             Issued 01-2006   Bur                   5-1380 NA

--- Page 35 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                                       CHAPTER 24 - COMPONENTS SYSTEM


CH24-45-01                                                                                                     Figure 59

24.1.8.3.3 ARM IN OPERATION UNDER HEAVY                        The hydraulic oil that flowed into the arm recirculation
LOAD                                                           spool (310) does not flow to the arm cylinder head
When the arm is operated under a heavy load, the               (H) that is heavily loaded, but flows to tank port (T)
arm oil recirculation function is effective as when the        from low pressure circuit (D) and returns to the
arm cylinder is operating under a light load.                  hydraulic oil tank.

The control valve switches automatically between oil           Sequenced conflux:
recirculation under light load conditions and no               If the arm cylinder head (H) is loaded heavily, the
recirculation under heavy load conditions by                   solenoid proportional valves (C) and (D) operate in
detecting pump pressure. This is called variable               addition to the above mentioned recirculation cut
recirculation. When the arm is under a heavy load,             action. As a result, each secondary pressure acts
when no recirculation occurs, the oil supply passage           upon the PTb and Pcb ports of the control valve,
to the arm cylinder is the same as during                      changes the travel straight spool (307) to position (II)
recirculation for a light load, but the return oil             and changes the P1 bypass cut spool (309).
passage is different.                                          As a result, the oil flow from the pumps P1 opens
The system detects the pump pressure at heavy load             check poppet CT2 as P1 bypass cut spool (309) has
conditions (more than 200 kgf/cm 2 (2840 psi) of               shifted and hydraulic oil of pump P2 is flowing in the
pump pressure. This causes the secondary pressure              parallel circuit (56) of the control valve. This supplies
of solenoid proportional valve (A) to operate and              the arm cylinder head (H).
changes the arm recirculation spool (310) to position
(I).


24-54                                                                          Issued 01-2006   Bur            5-1380 NA

--- Page 36 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                               CHAPTER 24 - COMPONENTS SYSTEM

24.1.9.3 CONSTRUCTION


CH24-55-011                                                                                    Figure 70

24-64                                                                   Issued 01-2006   Bur   5-1380 NA

--- Page 37 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                                CHAPTER 24 - COMPONENTS SYSTEM

24.1.11.2 TRAVEL MOTOR (FOR L TYPE)
24.1.11.2.1 SPECIFICATIONS


C24-65-01                                                                                       Figure 81
24-74                                                                    Issued 01-2006   Bur   5-1380 NA

--- Page 38 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                             CHAPTER 24 - COMPONENTS SYSTEM

24.1.14 HYDRAULIC MOTOR


C24-75-01                                                                                    Figure 93


24-84                                                                 Issued 01-2006   Bur   5-1380 NA

--- Page 39 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                               CHAPTER 24 - COMPONENTS SYSTEM

24.1.17 SWIVEL JOINT SPECIFICATION

24.1.17.1 GENERAL VIEW (SPEC.1)


CH24-85-01                                                                                     Figure 103

24-94                                                                   Issued 01-2006   Bur    5-1380 NA

--- Page 40 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                                      CHAPTER 24 - COMPONENTS SYSTEM

Cushion on head side
The construction of the head side cushion is similar
to that of the rod side. In a state of intermediate
stroke on the pressing rod side, oil in chamber β€œA”
returns to the tank by passing through paths β€œB” and
β€œC” at a fixed flow rate.
Prior to the stroke end, the plunger blocks path β€œB”.
The oil in chamber β€œA”, path clearance β€œD”, and
restricted path β€œC” suddenly drops as the oil flow
volume is returning to the tank. This causes the
piston movement to slow.


                                                              CH24-95-01                             Figure 113


24-104                                                                        Issued 01-2006   Bur    5-1380 NA

--- Page 41 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                     CHAPTER 24 - COMPONENTS SYSTEM


CH24-105-01                                                                          Figure 123

24-114                                                        Issued 01-2006   Bur    5-1380 NA

--- Page 42 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                     CHAPTER 24 - COMPONENTS SYSTEM


CH24-115-01                                                                          Figure 133

24-124                                                        Issued 01-2006   Bur    5-1380 NA

--- Page 43 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                     CHAPTER 24 - COMPONENTS SYSTEM


CH24-125-01                                                                          Figure 143

24-134                                                        Issued 01-2006   Bur    5-1380 NA

--- Page 44 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                            CHAPTER 25 - AIR CONDITIONING SYSTEM

25.1.1.2 COMPONENT CONSTRUCTION

25.1.1.3 INTAKE UNIT


CH25-06-01                                                                                     Figure 4

25-6                                                                   Issued 01-2006   Bur   5-1390 NA

--- Page 45 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                                   CHAPTER 25 - AIR CONDITIONING SYSTEM

25.2.1 REMOVAL AND INSTALLATION                               25.2.1.0.2 REPLACING THE BLOWER MOTOR
25.2.1.0.1 REMOVING THE BLOWER UNIT


CH25-16-01                                   Figure 16
Remove the connectors fastening the inner/outer air           CH25-16-03                                      Figure 18
select motor actuator, the blower motor and the               To replace the blower motor, disconnect the cooling
blower controller. Remove the electrical harness from         hose connecting the blower motor and the blower
the blower casing.                                            casing. Remove the 3 Phillips screws N5 X16 (W)
                                                              from the bottom of the blower unit casing. Remove
                                                              the blower motor.
                                                              NOTE: Do not separate the fan from the blower
                                                              motor.
                                                              Assembly is the reverse order of disassembly.


                                                              25.2.1.0.3 REPLACING THE BLOWER
                                                              CONTROLLER
                                                              Remove the 2 Phillips screw T4X14 (T1) from the
                                                              bottom of the blower unit casing and draw out the
                                                              blower controller. Install a new blower controller in the
                                                              reverse order of removal.
                                                              NOTE: Do not disassemble the blower controller
                                                              under any circumstances. Replace it as a complete
                                                              unit.
CH25-16-021                                  Figure 17
Remove the inner air filter from the intake casing.
Remove the 4 Phillips screws T5 X 14 (T1) from the
top of the intake casing. Then remove the intake
casing. Remove the 3 screws T5 X14 (T1) fastening
the blower casing to the unit casing. Separate the
blower unit from the air conditioner unit.


25-16                                                                         Issued 01-2006   Bur            5-1390 NA

--- Page 46 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
             CHAPTER 25 - AIR CONDITIONING SYSTEM


                               NOTES


25-26                                                   Issued 01-2006   Bur   5-1390 NA

--- Page 47 ---
SECTION 2 - HYDRAULIC, ELECTRICAL, AND COMPONENT SYSTEMS
                   CHAPTER 25 - AIR CONDITIONING SYSTEM


CH25-36-1ID                                                                          Figure 52

25-36                                                         Issued 01-2006   Bur   5-1390 NA

--- Page 48 ---
SECTION 3 - DISASSEMBLY AND ASSEMBLY
       CHAPTER 31 - GENERAL DISASSEMBLY AND ASSEMBLY


                            NOTES


31-4                                                  Issued 01-2006   Bur   5-1410 NA

--- Page 49 ---
SECTION 3 - DISASSEMBLY AND ASSEMBLY
                                            CHAPTER 32 - ATTACHMENTS

32.1.4 BOOM                                                       5. After adjustment of shim, the total gap should be
32.1.4.1 REMOVAL OF BOOM                                             within 0.6-2 mm (0.02-0.08 inches).


CH32-09-01                                     Figure 15
 1. Lower the boom and support the boom end with
    a suitable stand.
 2. Disconnect all hoses from the bucket cylinder,
    arm cylinder and boom cylinder, install plugs in
    all the openings.
                                                                CH32-10-01                                    Figure 18
 3. Disconnect the wiring for working light at the
    connector.                                                    6. To disconnect cylinder pipes, retract boom
                                                                     cylinder rod and place one side of cylinder on
                                                                     block.


                                                                CH32-10-02                                    Figure 19

CH32-09-02                                     Figure 16
                                                                  7. To disconnect arm cylinder piping, release the
                                                                     pressure in the hydraulic tank and disconnect
 4. To remove boom cylinder, lift up boom with an
                                                                     pipe at section DD. After disconnection, plug
    appropriate lifting device or nylon sling to prevent
                                                                     pipes to prevent dust, debris contamination.
    the boom cylinder from falling. Remove the cap
    screw and nuts that secure pin (C), then remove
    pin (C).


CH32-09-03                                     Figure 17


32-8                                                                             Issued 01-2006   Bur         5-1420 NA

--- Page 51 ---
SECTION 3 - DISASSEMBLY AND ASSEMBLY
                                            CHAPTER 32 - ATTACHMENTS

32.1.7.4 REMOVING PIN BUSHINGS                                  32.1.7.4.2 ASSEMBLING PISTON ASSEMBLY


CH32-23-01                                     Figure 50
 1. The cylinder tube is pressed into the pin bushing
    (2) of the piston rod. When disassembling, use a
    jig (A) and push the rod out.
                                                                CH32-24-01                                     Figure 52
 2. When all cylinder parts have been disassembled,               2. Coat O-ring (8) with hydraulic oil and set in place
    wash all parts with a suitable solution. Do not use              using inserting jig. Push slipper seal (10-1) in
    volatile agents such as gasoline or thinner, as                  place. Slipper seal will soften if heated, but do
    they deteriorate rubber. Do not reuse the oil                    not heat the seal above 100Β° C (212Β° F).
    seals, o-rings, or back-up rings. Dry all parts with
    jet air and protect them from damage.


32.1.7.4.1 CYLINDER TUBE AND
PISTON ROD ASSEMBLY


                                                                CH32-24-02                                     Figure 53

                                                                  3. Hold the heated seal in place, using a holding jig
                                                                     (G). Wind vinyl tape around seal and leave in
                                                                     place before piston (7) is set into cylinder tube.
                                                                     Attach wear ring and dust ring when inserting
CH32-23-02                                     Figure 51             piston (7) into cylinder tube.
 1. Press fit pin bushing (2) into cylinder tube (12)
    and piston rod (4).


32-18                                                                            Issued 01-2006   Bur           5-1420 NA

--- Page 52 ---
SECTION 3 - DISASSEMBLY AND ASSEMBLY
                                  CHAPTER 32 - ATTACHMENTS

32.1.9.3 SLIPPER SEAL - HOLD DOWN JIG


CH32-35-01                                                                                    Figure 76

32-28                                                                  Issued 01-2006   Bur   5-1420 NA

--- Page 53 ---
SECTION 3 - DISASSEMBLY AND ASSEMBLY
                                           CHAPTER 33 - UPPER SLEWING STRUCTURE

33.0.8 INSTRUMENT PANEL


                                                                     CH33-06-03                                         Figure 13
                                                                       3. To remove the control box, remove the four sems
                                                                          bolts (19) M8 on right and left side. Separate the
CH33-06-01                                          Figure 11             control box from its support.
 1. Prepare for removal of instrument panel by                                    Left control box weight: 8.5 kg (19 pounds)
    disconnecting the negative ter minal of the                                   Right control box weight: 7 kg (15 pounds)
    battery. To remove the right hand and left hand                               including pilot valve
    instrument panel, remove 8 sems bolts (12) M5.


                                                                     33.0.9 INSTRUMENT PANEL INSTALLATION
                                                                     Install the instrument panel in the reverse order of
                                                                     removal, tightening all bolts according to
                                                                     recommended torque.


                                                                     CH33-06-04                                         Figure 14


CH33-06-02                                          Figure 12
 2. Lift the panel up slightly to remove the two
    connectors for air conditioning (8P), tuner (9P)
    and the antenna cable on rear side of the left
    instrument panel.
             8P - Air conditioning panel
             9P - Tuner
             6P - Key switch
             3P - Accelerator panel
             2P and 8P - Switch panel


33-8                                                                                     Issued 01-2006   Bur           5-1430 NA

--- Page 54 ---
SECTION 3 - DISASSEMBLY AND ASSEMBLY
                                 CHAPTER 33 - UPPER SLEWING STRUCTURE

33.0.15 PUMP (MAIN)                                         33.0.15.2 PUMP (MAIN) REMOVAL
33.0.15.1 REMOVAL PREPARATION


                                                            CH33-19-03                                   Figure 44
                                                              1. Loosen half clamp (11) on the hoses (5), (6) and
                                                                 the cap screws (12) M10 X 35. Disconnect two
                                                                 hoses (A1), (A2) on the delivery side.
                                                              2. Remove four cap screws (13) M12 X 30, then
                                                                 remove suction tube (1) of suction hose (4) from
CH33-19-01                                 Figure 42             the pump.
 1. To remove main hydraulic pump, first remove
    counterweight. Though pump can be removed
    without removing counterweight, the removal of
    counterweight will reduce working time.
 2. Release pressure in hydraulic oil tank. Remove
    the six cap screws (A12) M10, remove cover (A6)
    and remove suction strainer.


CH33-19-02                                 Figure 43
 3. Remove the six cap screws (41) M12 X 25 and
    the two cap screws (42) M12 X 30. Then remove
    guard (18, 19) and disconnect drain pipe
    installed under the engine muffler.


33-18                                                                        Issued 01-2006   Bur        5-1430 NA

--- Page 55 ---
SECTION 3 - DISASSEMBLY AND ASSEMBLY
                                   CHAPTER 33 - UPPER SLEWING STRUCTURE


CH33-25-04                                                                                                    Figure 67
33.0.17.2 REMOVAL                                               4. Hook the lifting devise to the lifting lugs and the
 1. The engine is bolted to the frame. In order to                 front and rear of the engine. Lift slowly, first
    remove it, first remove the four nuts (7) M18, the             removing any slack from the lifting line.
    rubber mounts (3) and metal shims (13), (14).               5. Position the engine on the engine mounting
 2. Remove the four cap screws (4), (5), (6), the two              stand in a safe and stable fashion.
    washers (8), two plates (9), and two rubber               33.0.17.3 INSTALLATION
    mounts (1), (2). Make note of which cap screws
                                                                1. Installation is the reverse order of disassembly.
    these parts were removed from.
                                                                2. Adjust the clearance between the lower
 3. Prepare to sling the engine. A lifting devise
                                                                   mounting surface of the engine and rubber
    capable of holding the weight of engine must be
                                                                   mount (3) to 1.0 mm (0.039) using shims (13)
    available.
                                                                   and (14).
     Engine Weight: Approx. 370 kg (820 pounds)
                                                                3. Refer to the above figure for tightening torques
                                                                   and Loctite information.


33-28                                                                          Issued 01-2006   Bur           5-1430 NA

--- Page 56 ---
SECTION 3 - DISASSEMBLY AND ASSEMBLY
                                  CHAPTER 33 - UPPER SLEWING STRUCTURE

33.0.25.2 INSTALLATION


CH33-42-01                                   Figure 85
 1. Installation is performed in the reverse order of
    disassembly.
 2. Cleaning mating surfaces of upper frame and
    swing bearing.
 3. Apply Loctite #515 to the inside of the cap               CH33-42-01                                     Figure 86
    screws on the contact surface.                              5. Confirm reamer bolt position, and apply Loctite
                                                                   #262.
 4. Match the previously indicated marks on the
    upper frame and install with three reamer bolts                Tightening Torque: 28.5 kgfm (210 pound-foot)
    (11) temporarily.                                           6. Install the swing bearing by installing the twenty-
                                                                   five cap screws (10) M16 X 80. Apply Loctite

View the complete manual on HeyDownloads β†’