PDF Service Manual Liebherr R 9100 R 9100B Hydraulic Excavator - 8 MB

This in-depth service manual is the definitive resource for maintaining and repairing the Liebherr R 9100 and R 9100B hydraulic excavators.

It provides comprehensive procedures for disassembly, assembly, testing, and troubleshooting all major systems.

Written for professional technicians, this manual is essential for performing complex repairs and ensuring the machine operates to factory specifications.

A vital tool for any serious maintenance operation.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 3 ---
Service Manual
Welding

              Beginning with a material thickness of ¼’’ (8mm), butt welds must be made in several layers. The
              weld is applied in several beads. Wide butt welds are filled with several side beads, with the last layer
              covering the center. The electrode should melt evenly without creating burrs and peaks. The valley
              or crater, which is created when changing electrodes must be filled in and overlapped with the next
              electrode. To prevent cracks in those craters, care must be taken that they are properly filled.
              If the crack extends towards the outer edge of the material (pos. C), slag may be trapped or burn
              holes may be created. To prevent this, the following aid may be used : tack a piece of sheet of metal
              to the outer edge of material.
              The welding seam begins now at the sheet metal in the direction of the arrow (pos. C). After the weld-
              ing is completed, the sheet metal is removed and the edge of the material is ground smooth. The weld
              must cool off slowly and should therefore be protected from rain and wind.

      4.3.3   Reinforcement of the welding seam
              If the crack of the material is due to an oveload or abuse, a reinforcement plate should be welded
              over the crack. The selection of the correct reinforcement plate is based on the construction and load
              factors of the component to repair.
              For this reason, only general recommendations can be made as to the size and shape of the rein-
              forcement plates.

      4.3.4   General application of reinforcement plates

              Shape of reinforcement plates


              Fig. 5      shape of reinforcement plates
              The crossover or connection between the reinforced and not reinforced part should be as gradual as
              possible. This means that the size of the plate should be selected in such a way that new or unac-
              ceptable high stress in the repaired parts are avoided. Plates with sharp corners (such as a rectan-
              gular plate) should not be used.
              Suitable reinforcement plate with high tensile strenght (pos. D).
              Suitable reinforcement plate against bending and alternating loads (pos. E).

              Plate thickness
              The thickness of the reinforcement plate should be up to 2/3 (66%) of the thickness of the material to
              be reinforced.

              Plate quality
              The yield and tensile strenght of the reinforcement plate should be equal to the material to be rein-
              forced.

              Plate installation
              The welded area of the crack should be ground so it is a smooth and level.


1.00.20                                                                                            Mining excavators
                                                    copyright by

                                              MJFCIFSS

--- Page 13 ---
Component lifting                                                                          Service Manual
Uppercarriage parts

          2.4    Engine and oil cooler boxes / radiators

         2.4.1   Engine cooler box (without engine radiator)


                 Fig. 2     Lifting points of engine cooler box
                 Weight: 418 kg

         2.4.2   Engine radiator


                 Fig. 3     Lifting points of engine radiator
                 Weight (empty): 186 + 85 = 271 kg
                 Thread of the lifting nut: M16 x 20


3.20.2                                                                                             R 9100
                                   copyright © Liebherr-Mining Equipment Colmar SAS 2018

                                                 MJFCIFSS

--- Page 14 ---
Fig. 9    Solenoid valve Y7 on servo unit


Fig. 10   Hose of pressure cut-off valve on swing pump P5


                             MJFCIFSS

--- Page 17 ---
Tab. 1-2   Working technical data


Tab. 1-3   Working technical data for machine with Extra Wide (EW) undercarriage


              MJFCIFSS

--- Page 20 ---
Fig. 3-15   Submenus of the menu "Check"


              MJFCIFSS

--- Page 21 ---
Fig. 3-24   Button S122: Disable of ladder control position


Fig. 3-25   Emergency valve of access ladder


               MJFCIFSS

--- Page 22 ---
Fig. 3-52   Rotary switch for additional cab heater


               MJFCIFSS

--- Page 23 ---
Fig. 3-71   Warning lights of coolant preheating


               MJFCIFSS

--- Page 27 ---
Fig. 5-5   Drilled anchor point (example)


              MJFCIFSS

--- Page 29 ---
Fig. 5-41   Fuel connection under the fuel tank


               MJFCIFSS

--- Page 30 ---
Fig. 5-66   Oil filter parts


               MJFCIFSS

--- Page 31 ---
Fig. 5-89   Special expansion tank of Lifetime interspace


Fig. 5-90   Oil change on the Lifetime interspace


               MJFCIFSS

--- Page 32 ---
Fig. 5-116 Fan motor in the heater


              MJFCIFSS

--- Page 35 ---
Fig. 6-16   Intake and replenishing hoses


               MJFCIFSS

--- Page 36 ---
Operating Manual


    1 Guidelines
       As you read these instructions, you will notice a number of depictions and symbols which are
       to facilitate the navigation and understanding of these instructions.
       For reasons of better legibility, in these instructions we mainly use the male form for general
       references. Of course, the female form is also always intended.
       Please read these instructions thoroughly and heed the warning and safety notes. Please
       observe the warning and safety notes and exercise particular caution in these cases.
       Inform also other users accordingly.
          Text representations                        Meaning

          Bold print                                  Highlighting of particularly important words or
                                                      passages

                 List 1                               Marks lists

          o            List 2                         Marks lists

          (parenthesis)                               Item numbers

                 Instructions                         Instructions to personnel. These always
                                                      appear in chronological order.


       Explanation of symbols and signs
       Activities which generate actual hazards (to life and limb or possible damage to the material)
       are marked by warnings. Definitely observe the instructions given in the warnings.
       You will find these symbols, which warn of specific dangers to persons, material assets, or the
       environment, next to all safety instructions in these operating instructions.
       Please read these instructions thoroughly and heed the warning and safety notes. Please
       observe the warning and safety notes and exercise particular caution in these cases.
       Inform also other users accordingly.

       The following warnings are possible.
        Warning level                       Consequence                      Probability

                DANGER                      Death/ serious injury            imminent


                WARNING                     Serious injury                   possible


                CAUTION                     Minor injury                     possible

                ATTENTION                   Property damage
                                                                             possible


4                                                                                                 R 9100
                          Copyright © Liebherr Mining Equipment Colmar SAS 2018
                                          MJFCIFSS!

--- Page 37 ---
Operating Manual


         8 Technical data and operating instructions
             Operating pressure / operating temperature
             All system components must be designed for the maximum operating pressure and must be
             secured by an adequate pressure relief valve against too high system pressures. For details
             see operating or installation instructions and data sheets of the respective product.

             Installation position, sound pressure level, weight, dimensions
             For details see operating or installation instructions and data sheets of the respective
             product.

             Tightening torques
             For details see operating or installation instructions and data sheets of the respective
             product.

             Output / connections
             For details see operating or installation instructions and data sheets of the respective product.
             Deviating conditions such as NLGI class, temperature and counter pressure may lead to a
             deviation in the flow rate. This should be taken into account when designing the lubrication
             points.

             Filling possibilities
             For details see operating or installation instructions and data sheets of the respective
             product.

             Electrical connection (electrically driven products)
             Following the respective applicable installation prescriptions for electrical systems. For
             details see operating or installation instructions and data sheets of the respective product.

             IP type of protection
             Motor and system:
             For IP or NEMA protective class see type identification plate of motor or system respectively
             the Technical Data chapter of the individual components. For details see operating or
             installation instructions and data sheets of the respective product.

             Air pressure and air quality (air-operated products)
             Filtered and oiled air according to DIN ISO 8573-1 not higher than class 5

             Inlet air pressure                         5.5 – 7 bar

             Maximum particle density                   10 mg / m3

             Water content (pressure dew point)         + 7 °C

             Oil content (maximum oil concentration) 25 mg / m3
                          Please follow the instructions of the respective product.


R 9100                                                                                                       29
                             Copyright © Liebherr Mining Equipment Colmar SAS 2018
                                             MJFCIFSS!

--- Page 41 ---
Service Manual
                                                                                                         Cooling system

          2    Cooling system
               The cooling liquid is thermostatically controlled and its circulation is operated by a related water
               pump.
               Each cylinder unit is cooled individually through the distribution channels cast in the crankcase.
               The pistons are cooled through the cooling duct from the lubricating oil circuit of the Diesel engine.

         2.1   Cooling schematic


               Fig. 2      Cooling system diagram

               1   Coolant cooler / radiator                         7    Coolant collector rail
               2   Coolant inlet to the engine                       8    Coolant return to the thermostat
               3   Engine water pump                                 9    Thermostat
               4   Oil cooler                                        10 Coolant outlet to the radiator
               5   Coolant distributor rail                          A Supply from radiator
               6   Cylinder head / line                              B Return from engine


R 9100                                                                                                          6.00.5
                                  copyright © Liebherr-Mining Equipment Colmar SAS 2019

                                                 MJFCIFSS

--- Page 42 ---
Service Manual


      3.4.5   Start the engine after the fuel system bleeding

              With fuel prefilter with remote pump
                 Start the engine.
                 Operate it at low idle for approximately 10 minutes.

              With fuel prefilter with integrated pump
                 Start the engine.
                 Operate it 1800 RPM idle for approximately 10 minutes.
                 Stop the engine. Wait 2 minutes.
                 Start the engine again.
              If the engine does not start in less than 5 seconds:
                 Do the bleeding procedure of the fuel system again.


6.00.30                                                                                         R 9100
                                copyright © Liebherr-Mining Equipment Colmar SAS 2019

                                              MJFCIFSS

--- Page 43 ---
Fig. 16   Solenoid valves


                            MJFCIFSS

--- Page 48 ---
Service Manual


                 Fig. 8     Section of discharge two ways check valve


                  13       Connector plate - discharge two way          192        Discharge pressure - flow regulator
                           check valve                                  192.1      Piston
                  191.1    Piston                                       192.2      Flow regulator
                  191.2    Spring                                       192.3      Spring
                  191.3    Bushing                                      192.4      Bushing

         6.2.4   Function of discharge valves in connector plate
                 The discharge valves 191 and 192 allows a small amount of oil from the low-pressure connection on
                 the motor to escape into the motor housing.


R 9100                                                                                                          8.00.25
                                  copyright © Liebherr-Mining Equipment Colmar SAS 2018

                                                MJFCIFSS

--- Page 49 ---
Service Manual
                                                                                                     Adjustment

         6   Adjustment
                 For adjustment instructions, refer to the section "Adjustment procedure R9100" in chapter 3
                 "Technical Data" of this manual.


R 9100                                                                                                  9.00.23
                                copyright © Liebherr-Mining Equipment Colmar SAS 2018

                                              MJFCIFSS

--- Page 50 ---
Service Manual


     Energies
                               Electricity


                               Temperature (hot or cold surfaces)


                               Position energy (raised components)


                               Parts subject to pressure (operating pressure, oil pressure,
                               grease pressure, air pressure, etc.)
                               Bursting reservoir if filled by a high-performance pump


                               Parts subject to spring tension


     Lubricants
         Greases
         Oils

       Transport lifecycle
       Residual risks                        Remedy
       Tilting or falling of parts during    Secure parts against tilting or falling during transport
       transport, e.g. over inclines.        (e.g. using tapes, belts, ropes, etc.).
       Dropping of lifted parts or           No people may remain under suspended loads. Keep
       tools.                                unauthorized persons away.
                                             Secure suspended loads using suitable hoisting
                                             equipment (e.g. tapes, belts, ropes, etc.).


     Existing residual risks
      Installation life cycle
       Residual risks                        Remedy
        People slipping due to floor         Take care when filling. Bind and remove leaked or
        contamination with spilled           spilled lubricant immediately with a suitable agent.
        or leaked lubricant


                                             Follow the operational instructions for handling
                                             lubricants and contaminated parts.


12                                                                                              R 9100
                       Copyright © Liebherr Mining Equipment Colmar SAS 2018
                                        MJFCIFSS!

--- Page 51 ---
Service Manual

     9.2.3   Single-line system
     The single-line system consists of a pump to supply lubricant under pressure to the injector metering
     devices via the supply line. The injector metering devices deliver lubricant to a secondary
     (progressive) metering device or to the bearing through feed lines.

     The lubrication cycle is initiated by an automated pump. The injectors have indicator stems, which
     move in and out to indicate that they have been cycled.

     A controller will control the automated system.

     The time between on cycles and the length of off cycles is adjustable. The controller includes the
     timer function above with a monitor function and alarm capability. A pressure switch is used to
     indicate when system pressure has been reached to turn off the pump and verify that a lube cycle
     has been completed. If the pressure switch does not detect full pressure within a preset period of
     time, the controller goes into alarm state.

     9.2.4   Pump station 27L
                                                                              1      Dip stick

                                                                              2      Pump P1 – Model
                                                                                     FlowMaster II

                                                                              3      Hydaulic relief (vent) valve

                                                                              4      Contact rod – B96 (low level
                                                                                     control) + B185_1 (high-
                                                                                     level control)

                                                                              5      Overflow pipe

                                                                              6      Grease reservoir 27L for
                                                                                     FlowMaster II-pump

                                                                              7      Strainer assembly, pressure
                                                                                     line

                                                                              8      Lubricant filter, refilling

                                                                              9      Optical high-level control

                                                                            10       Solenoid Y34_1 (pump
                                                                                     control)


      Fig. 10-6    Central lubrication pump 27L


                  For information and descriptions of the components, refer to chapter 13.


R 9100                                                                                                              37
                             Copyright © Liebherr Mining Equipment Colmar SAS 2018
                                             MJFCIFSS!

--- Page 53 ---
Ë­»® Ó¿²«¿´
Ѱ»®¿¬·²¹ ײ­¬®«½¬·±²­

                                                                                                              îòîÛÒóîðððïóÖïï
                                                      ײ¬®±¼«½¬·±²

    Û¨°´¿²¿¬·±² ±º ͧ³¾±´­ Ë­»¼
̸» º±´´±©·²¹ ¼»­½®·°¬·±² ­¬¿²¼¿®¼­ ¿®» «­»¼ ·² ¬¸·­ ³¿²«¿´æ     Ú«®¬¸»®³±®»ô §±« ©·´´ º·²¼ ¬¸» º±´´±©·²¹ ¬»¨¬ ­§³¾±´­ ·² ¬¸·­
Í¿º»¬§ ײ­¬®«½¬·±²­                                              ³¿²«¿´æ
ͬ®«½¬«®» ±º ­¿º»¬§ ·²­¬®«½¬·±²­æ                                   Ô·­¬·²¹ ±º ¿°°´·½¿¾´» ­¬¿¬»³»²¬­
    з½¬±¹®¿³                                                       ó Í«¾°±·²¬ ±º ¿°°´·½¿¾´» ­¬¿¬»³»²¬­
    Í·¹²¿´ ©±®¼                                                  ïò Ü»¬»®³·²¿¬·±² ±º ¬¸» ²«³¾»® ±® ­»¯«»²½» ±º ½±²¬»²¬­
    Ü¿²¹»® ¬»¨¬                                                     Ю±½»¼«®¿´ ·²­¬®«½¬·±²
    ó Ü¿²¹»® ²±¬»
    ó Ø±© ¬± ¿ª±·¼ ¼¿²¹»®                                            Ë­»®ù­ λ­°±²­·¾·´·¬§
̸» º±´´±©·²¹ °·½¬±¹®¿³­ ¿®» «­»¼ ·² ¬¸·­ ³¿²«¿´ ¿²¼ ¿®»         ̱ »²­«®» ¬¸» ­¿º» ±°»®¿¬·±² ±º ¬¸» «²·¬ô ¬¸» «­»® ·­ ®»­°±²­·ó
½±³¾·²»¼ ©·¬¸ ¬¸» ½±®®»­°±²¼·²¹ ­·¹²¿´ ©±®¼­æ                    ¾´» º±® ¬¸» º±´´±©·²¹æ
                                                                 ïò ̸» °«³° ñ ­§­¬»³ ­¸¿´´ ¾» ±°»®¿¬»¼ ±²´§ º±® ¬¸» ·²¬»²¼ó
                                                                      »¼ «­» ø­»» ²»¨¬ ½¸¿°¬»® þÍ¿º»¬§ ײ­¬®«½¬·±²­þ÷ ¿²¼ ·¬­
                                                                      ¼»­·¹² ­¸¿´´ ²»·¬¸»® ¾» ³±¼·º·»¼ ²±® ¬®¿²­º±®³»¼ò
                                                                 îò ̸» °«³° ñ ­§­¬»³ ­¸¿´´ ¾» ±°»®¿¬»¼ ±²´§ ·º ·¬ ·­ ·² ¿
                                                                      °®±°»® º«²½¬·±²·²¹ ½±²¼·¬·±² ¿²¼ ·º ·¬ ·­ ±°»®¿¬»¼ ·² ¿½ó
                                                                      ½±®¼¿²½» ©·¬¸ ¬¸» ³¿·²¬»²¿²½» ®»¯«·®»³»²¬­ò
       ïðïíßçì             ìîéí¿ðð              êððï¿ðî          íò ̸» ±°»®¿¬·²¹ °»®­±²²»´ ³«­¬ ¾» º¿³·´·¿® ©·¬¸ ¬¸·­ Ë­»®
ó ßÌÌÛÒÌ×ÑÒ           ó ßÌÌÛÒÌ×ÑÒ        ó ÒÑÌÛ                       Ó¿²«¿´ ¿²¼ ¬¸» ­¿º»¬§ ·²­¬®«½¬·±²­ ³»²¬·±²»¼ ©·¬¸·² ¿²¼
                                                                      ±¾­»®ª» ¬¸»­» ½¿®»º«´´§ò
ó ÝßËÌ×ÑÒ             ó ÝßËÌ×ÑÒ          ó ×ÓÐÑÎÌßÒÌ
ó ÉßÎÒ×ÒÙ             ó ÉßÎÒ×ÒÙ
̸» ­·¹²¿´ ©±®¼­ ¹·ª» ¬¸» ­»®·±«­²»­­ ±º ¼¿²¹»® ·º ¬¸» º±´´±©ó
·²¹ ¬»¨¬ ·­ ²±¬ ±¾­»®ª»¼æ

ßÌÌÛÒÌ×ÑÒ                  ®»º»®­ ¬± º¿«´¬­ ±® ¼¿³¿¹»­ ±²
                           ³¿½¸·²»­ò
ÝßËÌ×ÑÒ                    ®»º»®­ ¬± ¾¿¼ ¼¿³¿¹»­ ¿²¼ °±­­·ó          Û²ª·®±²³»²¬¿´ Ю±¬»½¬·±²
                           ¾´» ·²¶«®·»­ò                         É¿­¬» ø»ò¹ò «­»¼ ±·´ô ¼»¬»®¹»²¬­ô ´«¾®·½¿²¬­÷ ³«­¬ ¾» ¼·­ó
ÉßÎÒ×ÒÙ                    ®»º»®­ ¬± °±­­·¾´» ¼¿²¹»®±«­ ·²¶«ó    °±­»¼ ±º ·² ¿½½±®¼¿²½» ©·¬¸ ®»´»ª¿²¬ »²ª·®±²³»²¬¿´ ®»¹«´¿ó
                           ®·»­ò                                 ¬·±²­ò
ÒÑÌÛ                       ·²¼·½¿¬»­ ·³°®±ª»¼ ±°»®¿¬·±² ±º ¬¸»
                           ¼»ª·½»ò
×ÓÐÑÎÌßÒÌ                  ·²¼·½¿¬»­ ­°»½·¿´ ±°»®¿¬·²¹ º»¿ó          Í»®ª·½»
                           ¬«®»­ ±º ¬¸» ¼»ª·½»ò

Û¨¿³°´»æ

                  ßÌÌÛÒÌ×ÑÒÿ
                  ɸ»² ³¿µ·²¹ «­» ±º ±¬¸»® ¬¸¿² ¬¸» ¬»­¬»¼
                  ­°¿®» °¿®¬­ô ­»®·±«­ ¼¿³¿¹» ³¿§ ¿ºº»½¬
                  §±«® ¼»ª·½»ò


      ïðïíßçì


Ð        ºî

--- Page 54 ---
User Manual
Installation Instructions

                                                                                                                   2.2EN-20003-G13
                                                  Safety Instructions

    Appropriate Use                                                     Installation
Use SSVD and SSVD-E lubricant metering devices only for                Install the metering devices at a suitable location in ac-
dispensing lubricants in centralized lubrication systems.              cordance with the lubrication diagram.
Suitable Lubricants                                                    It is recommended that the metering devices be installed in
   The progressive metering devices can be used for dis-               such a way that the outlets are not close to the chassis or
   pensing                                                             the attaching plate. This will facilitate troubleshooting in the
                                                                       case the system is blocked.
   - mineral oils of at least 40 mm²/s (cST) or
                                                                       The main metering devices with indicator pin must be
   - greases up to the penetration class NLGI 2                        installed in such a way that the indicator pin is easily visible.
                  IMPORTANT                                         When the push-in type fittings are used, note the follow-
                                                                    ing:
                  It must nevertheless be ensured that the             For the metering device inlet use only push-in type
                  oils or greases used do not alter their con-         fittings (R 1/8) with reinforced collar and sealing ring.
     6001a02      sistency significantly in the course of time or
                                                                       For the outlet tube fittings of the SSV divider valve
                  under the influence of temperature or
                                                                       (M 10x1) depending on the design of the lubricant line, for
                  pressure.
                                                                       example
                                                                       - high-pressure plastic hose (Ø 4.1 x 2.3) use valve bodies
    General Safety Instructions                                          with reinforced collar only, or,
   The progressive centralized lubrication system connected            - pressure plastic tube (Ø 6 x 1.5) use valve bodies with
   to a pump must always be secured with a pressure relief               knurled collar only
   valve.
                                                                       For the outlet fittings of the SSV M divider divider valve
   Lincoln SSVD and SSVD-E lubricant metering devices are              (M 8x1) pressure plastic tube (Ø 4 x 1) use valve bodies
   state of the art.                                                   with knurled collar only.
   Incorrect use may result in bearing damage caused by
                                                                                        NOTE
   poor or excessive lubrication.
   Each outlet needed must be provided with a check valve in                            In the case of construction machines or
   order to be able to feed the lube points with the precise                            agricultural machines use high pressure
   amount of lubricant and avoid poor lubrication.                                      plastic hoses for the lubricant feet lines. In
                                                                          6001a02       such cases the outlet fittings of the sec-
   In the case of the metering devices model SSVD6 to 22
   and SSVD6-E to 22-E outlets 1 and 2 must never be                                    ondary metering devices and the connec-
   closed.                                                                              tion fittings to the lubricant points must
                                                                                        have a reinforced collet.
   Outlets 1 and 2 of the special metering devices model
                                                                       Use only the main and feed lines specified by           and
   SSVD6/5 to 22/21 and SSVD6/5-E to 22/21-E are con-
                                                                       adhere to the specified system pressures.
   nected via a channel (marked by a double arrow). One of
   the two outlets must be closed. This means, the lubricant
   quantity of the closed outlet is lead to the opposite outlet
                                                                          Regulations for Prevention of Accidents
   (see Fig. 19).                                                        To prevent accidents, observe all city, state and federal
                  CAUTION                                                safety regulations of the country in which the product will
                                                                         be used.
                  Damage due to poor lubrication!                        Avoid the operation with
                                                                           - unapproved parts.
                  If, however, both outlets are connected to a             - insufficient or contaminated lubricants.
                  lube point the bypass metering device
     1013A94      SSVD6/5 to 22/21 and SSVD6/5-E to                                    CAUTION
                  22/21-E cannot work to 100 %. The lubri-                             Danger of injury in the case of serious
                  cant follows the way of the lowest re-                               corrosion of metering device surfaces:
                  sistance. It reaches the lube points of                              An increasing corrosion of the surfaces will
                  outlets 1 and 2 only insufficiently or not at                        cause the balls pressed in to lose their hold.
                  all.                                                                 Under pressure, they may suddenly burst
   Unauthorized modifications or changes to an installed                 1013A94       out and cause injuries.
   system are not admissible. Any modification must be                                 For applications in corrosive environments,
   subject to prior consultation with the manufacturer of the                          use metering devices in stainless steel
   lubrication system.                                                                 version only.
   Use only original spare parts (see Parts Catalog) or
   the parts approved by      .
                                                                        Operation, Repair and Maintenance
                                                                    Authorized and instructed personnel who are familiar with the
                                                                    centralized lubrication systems should only perform repair.
                                                                                                                          P     5 f 28

--- Page 57 ---
Owner Manual

                                     2.6A-20003-D04
                Technical Data


                                 M


Page 16 of 20

--- Page 58 ---
User Manual
P203 Parts Catalog

                                                                                                     2.0EN-20003-I13

  A                         with 2 l reservoir for grease or oil                                                    A

    P203-2XYNBO & P223/233-2XNBO-       without low-level control
                                                                                            1)        1)
   2 l reservoir with lid                                Control:                     V10-13 , V20-23 ,
                                                                                                2)        3)
                                                                                      MF/MDF01 , MF/MDF02
                                                                                            1)             1)           1)
   with stirring paddle                                  Type of connection: 1A1.01/10 , 2A1.01/10 , 1A5.14 ,
                                                                                      1)       2)       3)
                                                                               1A7.16 , 2A5.14 , 2A6.15


                                                    Pos. Designation                               Qty.         Part no.

                                                        A     Reservoir assembly
                                                                                 4)
                                                        A1    2-Liter-Behälter                      1      544-31940-1
                                                        1.1   Acorn nut M4 C                        1      207-12247-5
                                                        1.2   Nut M4 C                              1      207-12135-2
                                                        1.3   Washer A 4.3 C                        1      209-12146-2
                                                        1.4                              M4 x 16    1      201-12015-4
                                                        1.5   Lid                                   1      221-12488-5
                                                        A2    Hose 12.5 cm                          1      111-35089-2
                                                        A3    Stirring paddle incl. Pos. A2         1      544-33569-1
                                                        A4    Washer 8.4                            1      209-13072-6
                                                        A5    Inner ring                            2      444-24168-1
                                                        A6    Grooved ball bearing D 10/26 x 8      1      250-14009-7
                                                        A7    O-ring Ø 142 x 4                      2      219-13730-7
                                                        A8    Intermediate bottom                   1      444-24167-1
                                                        A9    Shim 10 x 16 x 0.5                    1      209-13047-5
                                                    A10       Snap ring SW 32                       2      211-14100-1
                                                    A11       Pressure ring Ø 33 x 37 x 13          1      444-24439-1
                                                    A12       Eccentric                             1      444-24170-2
                                                   1)
                                                         for P203
                                                   2)
                                                         for P223/233, PCB terminals 15 + 30 bridged
                                                   3)
                                                         for P223/233, PCB terminals 15 + 30 not bridged
                                                   1)

View the complete manual on HeyDownloads →