PDF Service Manual Hyundai HL970 Wheel Loader (2023) - 4 MB

This is the most current service manual for the 2023 Hyundai HL970 Wheel Loader.

It is an essential tool for any technician responsible for the maintenance and repair of this advanced machine.

The manual contains in-depth sections on the engine, powertrain, hydraulics, and electronic control systems.

With detailed diagrams and step-by-step procedures, it simplifies complex repairs.

Ensure your modern HL970 operates with the efficiency and reliability it was designed for by using this official service guide.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
CONTENTS

SECTION 1 GENERAL

  Group 1 Safety Hints -------------------------------------------------------------------------------------------------------- 1-1
  Group 2 Specifications ----------------------------------------------------------------------------------------------------- 1-10
  Group 3 Operational Checkout Record Sheet --------------------------------------------------------------- 1-23


SECTION 2 ENGINE

  Group 1 Structure and Function -------------------------------------------------------------------------------------- 2-1
  Group 2 Engine speed and Stall rpm ----------------------------------------------------------------------------- 2-3


SECTION 3 POWER TRAIN SYSTEM

  Group 1 Structure and Function -------------------------------------------------------------------------------------- 3-1
  Group 2 Operational Checks and Troubleshooting ------------------------------------------------------- 3-85
  Group 3 Test and Adjustments ---------------------------------------------------------------------------------------- 3-97
  Group 4 Disassembly and Assembly ----------------------------------------------------------------------------- 3-99


SECTION 4 BRAKE SYSTEM

  Group 1 Structure and Function -------------------------------------------------------------------------------------- 4-1
  Group 2 Operational Checks and Troubleshooting ------------------------------------------------------- 4-32
  Group 3 Tests and Adjustments -------------------------------------------------------------------------------------- 4-39
  Group 4 Disassembly and assembly ------------------------------------------------------------------------------ 4-41


SECTION 5 STEERING SYSTEM

  Group 1 Structure and Function -------------------------------------------------------------------------------------- 5-1
  Group 2 Operational Checks and Troubleshooting ------------------------------------------------------- 5-16
  Group 3 Tests and Adjustments -------------------------------------------------------------------------------------- 5-24
  Group 4 Disassembly and Assembly ----------------------------------------------------------------------------- 5-31


SECTION 6 WORK EQUIPMENT

  Group 1 Structure and Function -------------------------------------------------------------------------------------- 6-1
  Group 2 Operational Checks and Troubleshooting ------------------------------------------------------- 6-40
  Group 3 Tests and Adjustments -------------------------------------------------------------------------------------- 6-51
  Group 4 Disassembly and Assembly ----------------------------------------------------------------------------- 6-63

--- Page 3 ---
SECTION 1 GENERAL

Group 1 Safety Hints --------------------------------------------------------------------------------------------------------1-1
Group 2 Specifications -----------------------------------------------------------------------------------------------------1-10
Group 3 Operational Checkout Record Sheet ---------------------------------------------------------------1-23

--- Page 4 ---
GROUP 2 SPECIFICATIONS
1. MAJOR COMPONENT


           Bucket           Tire      Head light           Hydraulic tank       Radiator


       Boom       Boom cylinder       Main control valve           Battery         Counterweight


    Bell crank    Bucket cylinder        Cab       Main pump      Air cleaner      Engine


    Bucket link     Front axle     Steering cylinder      Transmission       Rear axle     Fuel tank


                                                                                                       770F2SE01


                                                   1-10

--- Page 5 ---
2) PIPE AND HOSE (FLARE type)
    Thread size      Width across flat (mm)          kgf·m   lbf·ft

        1/4"                   19                     4      28.9
        3/8"                   22                     5      36.2
        1/2"                   27                     9.5    68.7
        3/4"                   36                     18     130
         1"                    41                     21     152
       1-1/4"                  50                     35     253


3) PIPE AND HOSE (ORFS type)
    Thread size      Width across flat (mm)          kgf·m   lbf·ft

      9/16-18                  19                     4      28.9
     11/16-16                  22                     5      36.2
     13/16-16                  27                     9.5    68.7
     1-3/16-12                 36                     18     130
     1-7/16-12                 41                     21     152
     1-11/16-12                50                     35     253


4) FITTING

    Thread size      Width across flat (mm)          kgf·m   lbf·ft

        1/4"                   19                     4       28.9
        3/8"                   22                     5       36.2
        1/2"                   27                     9.5     68.7
        3/4"                   36                     18      130
         1"                    41                     21      152
       1-1/4"                  50                     35      253


                                              1-20

--- Page 6 ---
SECTION 3 POWER TRAIN SYSTEM

Group 1 Structure and Function -------------------------------------------------------------------------------------- 3-1
Group 2 Operational Checks and Troubleshooting -------------------------------------------------------- 3-85
Group 3 Tests and Adjustments -------------------------------------------------------------------------------------- 3-97
Group 4 Disassembly and Assembly ------------------------------------------------------------------------------ 3-99

--- Page 7 ---
② Forward 2nd
  In 2nd forward, forward clutch (KV) and 2nd clutch (K2) are engaged.
  Forward clutch and 2nd clutch are actuated by the hydraulic pressure applied to the clutch
  piston.


  INPUT

                                     KV      K1


                                     KR      K2


                                      K4      K3


                            OUTPUT                                            OUTPUT


                                                                                     77093PT08


                                           3-10

--- Page 8 ---
·Protection against operating errors, as far as possible and practical.
   ·Protection against overspeeds (on the basis of engine and turbine speed).
   ·Reversing-automatic system (driving speed-dependent).
   ·Pressure cut off (disconnecting of the drive train for maximum power on the power take-off).
   ·Switch for manual or automatic operation.
   ·Reversing function button, respectively kickdown function.

(3) Gearshifts
    The control unit (EST-37A) is shifts the required speeds fully-automatically under consideration of
    the following criteria.
    ·Gear selector position
    ·Driving speed
    ·Load level
   At the same time, the following speeds are picked up by the control unit (EST-37A).
   ·n Engine
   ·n Turbine
   ·n Central gear train
   ·n Output

   - Neutral position
   Neutral position is selected through the gear selector.
   After the ignition is turned on, the electronics remains in the waiting state; By the position neutral
   of the gear selector, respectively by pressing on the key neutral, the control unit (EST-37A)
   becomes ready for operation.
   Now, a speed can be engaged.
   - Speed engagement
   In principle, the speed, adapted to the driving speed (at standing, or rolling machine), will be
   engaged. The engagement is realized in dependence on load and rotational speed.
   - Upshifting under load
   Upshifting under load will be then realized if the machine can still accelerate by it.
   - Downshifting under load
   Downshifting under load will be realized if more traction force is needed.
   - Upshifting in coasting condition
   In the coasting condition, the upshifting will be suppressed if the speed of the machine on a slope
   shall not be further increased.
   - Downshifting in coasting condition
   Downshiftings in the coasting condition will be realized if the machine shall be retarded.
   - Reversing
   At speeds below the reversing limit, direct reversing can be carried out at any time in the speeds
   1F 1R and 2F 2R (as a rule, this is the maximum driving speed of the 2nd speed).


                                                3-20

--- Page 9 ---
2) ENGINE FAULT CODE
Fault code
J1939 SPN                       Name                                       Description
J1939 FMI
  12D1       Pnuematic supply pressure          Low air pressure signal from APS
   46
    1
  12D4       Pnuematic supply pressure           CAN message timeout from APS
   46
   19
  2123       Engine throttle valve position     Throttle Position Sensor 1, short circuit to +24
   51
    3
  2122       Engine throttle valve position     Throttle Position Sensor 1, short circuit to ground
   51
    4
  2121       Engine throttle valve position     Throttle Position Sensor, not plausible
   51
    7
  1091       Engine throttle valve position     Endpoints of throttle position sensor are out of range
   51
    8
  2138       Engine throttle valve position     Throttle Position Sensor, correlation error
   51
    9
  16C9       Accelerator pedal position         Auxiliary accelerator pedal is used due to other fault
   91
    2
  16C8       Accelerator pedal position         Accelerator pedal faulty or error via can
   91
    9
  D415       Accelerator pedal position         Accelerator pedal not plausible, faulty
   91
   10
  D414       Accelerator pedal position         Accelerator pedal value out of range via CAN
   91
   19
  1100       Engine fuel deliver pressure       Accumulator pressure is too high
   94
    0
  250A       Engine oil level                   Oil level sensor, faulty
   98
    2
  250D       Engine oil level                   Oil level sensor, short circuit to +24V
   98
    3
  250C       Engine oil level                   Oil level sensor, short circuit to ground
   98
    4
  1715       Engine oil level                   Oil level sensor stuck
   98
   10
 ※ Some fault codes are not applied to this machine.


                                              3-25

--- Page 10 ---
Fault code
J1939 SPN                    Name                                    Description
J1939 FMI
  1214       Engine position sensor            Camshaft position sensor, faulty
   636
    1
  0344       Engine position sensor            Camshaft position sensor, intermittent fault
   636
    2
  0343       Engine position sensor            Camshaft position sensor, short circuit to +24V
   636
    3
  0342       Engine position sensor            Camshaft position sensor, short circuit to ground
   636
    4
  0340       Engine position sensor            Camshaft position sensor, open circuit
   636
    5
  0016       Engine position sensor            Engine speed detected by flywheel sensor, but no
   636                                         signal from camshaft sensor
    7
  0341       Engine position sensor            Camshaft Pulse Pattern, Gap or Sync Error or other
   636                                         fault
    8
  16E7       Engine turbocharger actuator      VGT internal temperature sensor stuck
   641
    2
  1686       Engine turbocharger actuator      VGT voltage supply open load
   641
    4
  16B5       Engine turbocharger actuator      VGT internal temperature sensor open circuit
   641
    5
  168B       Engine turbocharger actuator      VGT motion limited or restricted
   641
    7
  168E       Engine turbocharger actuator      VGT reference or position not found
   641
    8
  1134       Engine turbocharger actuator      VGT temperature sensor value not plausible
   641
    9
  168C       Engine turbocharger actuator      VGT motion error, span too large
   641
    10
  1689       Engine turbocharger actuator      VGT actuator faulty
   641
    11
  1693       Engine turbocharger actuator      VGT internal fault
   641
    12
 ※ Some fault codes are not applied to this machine.


                                            3-35

--- Page 11 ---
Fault code
J1939 SPN                     Name                                       Description
J1939 FMI
  1606       Source address of engine control device EMS Memory Error
  1483
    2
  1610       Source address of engine control device EMS Memory Error
  1483
    2
  1607       Source address of engine control device EMS Memory or TPU Error
  1483
    8
  160F       Source address of engine control device EMS memory or TPU error
  1483
    8
  16D7       Source address of engine control device Camshaft TPU Supervision Error
  1483
    9
  160A       Source address of engine control device Software Watchdog Reset
  1483
   11
  1604       Source address of engine control device Hardware watchdog error
  1483
   12
  D100       Other control are repor ting faults CAN message DLN1 from coordinator timeout
  1484       affecting the engine
    9
  D102       Other control are repor ting faults CAN message CRUISE CONTROL/ VEHICLE
  1484       affecting the engine                SPEED from coordinator timeout
   10
  D113       Other control are repor ting faults CAN message from EMSX, invalid data
  1484       affecting the engine
   16
  D112       Other control are repor ting faults CAN message from EMSX, invalid data
  1484       affecting the engine
   18
  D103       Other control are repor ting faults CAN message DLN6 from coordinator timeout
  1484       affecting the engine
   19
  D111       Other control are repor ting faults CAN message timout from EMSX
  1484       affecting the engine
   20
  D110       Other control are repor ting faults CAN message timout from EMSX
  1484       affecting the engine
   21
  20EA       ECM main relay                         SCR main unit, power switched off too early
  1485
   16
  20EB       ECM main relay                         SCR main unit, power switched off too late
  1485
   18
 ※ Some fault codes are not applied to this machine.


                                                3-45

--- Page 12 ---
Fault code
J1939 SPN                      Name                                      Description
J1939 FMI
  0069       Engine intake manifold pressure     Boost pressure sensor and ambient pressure sensor
  3563                                           do not correlate
   17
  F001       Engine emergency shutdown           Incorrect EMS shutdown
  3607
    2
  2128       Engine throttle valve position      Throttle Position Sensor 2, short circuit to +24V
  3673
    3
  2127       Engine throttle valve position      Throttle Position Sensor 2, short circuit to ground
  3673
    4
  0406       Engine EGR valve position           EGR position sensor, short circuit to +24V
  3822
    3
  0405       Engine EGR valve position           EGR position sensor, short circuit to ground
  3822
    4
  1405       Engine EGR valve position           EGR SRA reports a warning during Learn Stops.
  3822
    7
  049D       Engine EGR valve position           EGR position sensor, outside the permitted range
  3822
    8
  1404       Engine EGR valve position           EGR SRA reports it has a continuous fault.
  3822
   12
  1705       Engine EGR valve position           EGR position sensor, not plausible
  3822
   13
  1406       Engine EGR valve position           EGR SRA reports a running conditions warning for
  3822                                           high temp or low voltage.
   16
  1402       Engine EGR valve position           EGR CAN timeout
  3822
   19
  1813       Engine EGR valve position           EGR position sensor, voltage shows large variation in
  3822                                           open position
   20
  1814       Engine EGR valve position           EGR position sensor, voltage shows large variation in
  3822                                           closed position
   21
  244B       After treatment - DPF filter        Particulate filter, clogged
  3936
    2
  242F       After treatment - DPF filter        Particulate filter, ash level too high
  3936
    6
 ※ Some fault codes are not applied to this machine.


                                               3-55

--- Page 13 ---
Fault code          Meaning of the fault code               Reaction of the TCU             Possible steps to repair
  (Hex)          possible reason for fault detection
   34        S.C. to battery voltage or O.C. at turbine OP mode : Substitute clutch · Check the cable from TCU to the
             speed input                                            control            sensor
             TCU measures a voltage higher than If a failure is existing at · Check the connectors
             7.00V at speed input pin                    output speed,               · Check the speed sensor
             ·Cable is defective and is contacted to TCU shifts to neutral
                vehicle battery voltage                  OP mode : Limp home
             ·Cable has no connection to TCU
             ·Speed sensor has an internal defect
             ·Connector pin is contacted to battery
                voltage or has no contact
   35        S.C. to ground at turbine speed input       OP mode : Substitute clutch · Check the cable from TCU to the
             TCU measures a voltage less than 0.45V                 control            sensor
             at speed input pin                          If a failure is existing at · Check the connectors
             ·Cable/connector is defective and is output speed,                      · Check the speed sensor
                contacted to vehicle ground              TCU shifts to neutral       ※ This fault is reset after power up of
             ·Speed sensor has an internal defect        OP mode : Limp home           TCU
   36        Logical error at turbine speed input        OP mode : Substitute clutch · Check the cable from TCU to the
             TCU measures a turbine speed over a                    control            sensor
             threshold and at the next moment the If a failure is existing at · Check the connectors
             measured speed is zero                      output speed,               · Check the speed sensor
             ·Cable/connector is defective and has TCU shifts to neutral             · Check the sensor gap
                bad contact                              OP mode : Limp home
             ·Speed sensor has an internal defect
             ·Sensor gap has the wrong size
   37        S.C. to battery voltage or O.C. at internal OP mode : Substitute clutch · Check the cable from TCU to the
             speed input                                            control            sensor
             TCU measures a voltage higher than                                      · Check the connectors
             7.00V at speed input pin                                                · Check the speed sensor
             ·Cable is defective and is contacted to
                vehicle battery voltage
             ·Cable has no connection to TCU
             ·Speed sensor has an internal defect
             ·Connector pin is contacted to battery
                voltage or has no contact
   38        S.C. to ground at turbine speed input       OP mode : Substitute clutch · Check the cable from TCU to the
             TCU measures a voltage less than 0.45V                 control            sensor
             at speed input pin                                                      · Check the connectors
             ·Cable/connector is defective and is                                    · Check the speed sensor
                contacted to vehicle ground
             ·Speed sensor has an internal defect
   39        Logical error at internal speed input       OP mode : Substitute clutch · Check the cable from TCU to the
             TCU measures a internal speed over a                   control            sensor
             threshold and at the next moment the                                    · Check the connectors
             measured speed is zero                                                  · Check the speed sensor
             ·Cable/connector is defective and has                                   · Check the sensor gap
                bad contact                                                          ※ This fault is reset after power up of
             ·Speed sensor has an internal defect                                      TCU
             ·Sensor gap has the wrong size
   3A        S.C. to battery voltage or O.C. at output Special mode for gear · Check the cable from TCU to the
             speed input                                 selection                     sensor
             TCU measures a voltage higher than OP mode : S u b s t i t u t e · Check the connectors
             12.5V at speed input pin                                clutch control · Check the speed sensor
             ·Cable is defective and is contacted to If a failure is existing at
                battery voltage                          turbine speed,
             ·Cable has no connection to TCU             TCU shifts to neutral
             ·Speed sensor has an internal defect        OP mode : Limp home
             ·Connector pin is contacted to battery
                voltage or has no contact
※ Some fault codes are not applied to this machine.

                                                            3-65

--- Page 14 ---
Fault code           Meaning of the fault code                  Reaction of the TCU                 Possible steps to repair
  (Hex)           possible reason for fault detection
   B3        Slippage at clutch K3                        TCU shifts to neutral      · Check pressure at clutch K3
             TCU calculates a differential speed at OP mode : Limp home              · Check main pressure in the system
             closed clutch K3. If this calculated value If failure at another clutch · Check sensor gap at internal speed
             is out of range, TCU interprets this as is pending                        sensor
             slipping clutch                              TCU shifts to neutral      · Check sensor gap at output speed
             ·Low pressure at clutch K3                   OP mode : TCU shutdown       sensor
             ·Low main pressure                                                      · Check signal at internal speed
             ·Wrong signal at internal speed sensor                                    sensor
             ·Wrong signal at output speed sensor                                    · Check signal at output speed
             ·Wrong size of the sensor gap                                             sensor
             ·Clutch is defective                                                      Replace clutch
   B4        Slippage at clutch K4                        TCU shifts to neutral      · Check pressure at clutch K4
             TCU calculates a differential speed at OP mode : Limp home                Check main pressure in the system
             closed clutch K4. If this calculated value If failure at another clutch · Check sensor gap at internal speed
             is out of range, TCU interprets this as is pending                        sensor
             slipping clutch                              TCU shifts to neutral      · Check sensor gap at turbine speed
             ·Low pressure at clutch K4                   OP mode : TCU shutdown       sensor
             ·Low main pressure                                                      · Check signal at internal speed
             ·Wrong signal at internal speed sensor                                    sensor
             ·Wrong signal at turbine speed sensor                                   · Check signal at turbine speed
             ·Wrong size of the sensor gap                                             sensor
             ·Clutch is defective                                                      Replace clutch
   B5        Slippage at clutch KV                        TCU shifts to neutral      · Check pressure at clutch KV
             TCU calculates a differential speed at OP mode : Limp home              · Check main pressure in the system
             closed clutch KV. If this calculated value If failure at another clutch · Check sensor gap at internal speed
             is out of range, TCU interprets this as is pending                        sensor
             slipping clutch                              TCU shifts to neutral      · Check sensor gap at turbine speed
             ·Low pressure at clutch KV                   OP mode : TCU shutdown       sensor
             ·Low main pressure                                                      · Check signal at internal speed
             ·Wrong signal at internal speed sensor                                    sensor
             ·Wrong signal at turbine speed sensor                                   · Check signal at turbine speed
             ·Wrong size of the sensor gap                                             sensor
             ·Clutch is defective                                                    · Replace clutch
   B6        Slippage at clutch KR                        TCU shifts to neutral      · Check pressure at clutch KR
             TCU calculates a differential speed at OP mode : Limp home                Check main pressure in the system
             closed clutch KR. If this calculated value If failure at another clutch · Check sensor gap at internal speed
             is out of range, TCU interprets this as is pending                        sensor
             slipping clutch                              TCU shifts to neutral      · Check sensor gap at turbine speed
             ·Low pressure at clutch KR                   OP mode : TCU shutdown       sensor
             ·Low main pressure                                                      · Check signal at internal speed
             ·Wrong signal at internal speed sensor                                    sensor
             ·Wrong signal at turbine speed sensor                                   · Check signal at turbine speed
             ·Wrong size of the sensor gap                                             sensor
             ·Clutch is defective                                                    · Replace clutch
   B7        Overtemp sump                                No reaction                · Cool down machine
             TCU measured a temperature in the oil OP mode : Normal                  · Check oil level
             sump that is over the allowed threshold.                                · Check temperature sensor
   B9        Overspend engine                             Retarder applies
                                                                                                            -
                                                          OP mode : Normal
   BA        Differential pressure oil filter             No reaction                · Check oil filter
             TCU measured a voltage at differential OP mode : Normal                 · Check wiring from TCU to
             pressure switch out of the allowed range                                  differential pressure switch
             ·Oil filter is polluted                                                 · C h e ck d i f fe r e n t i a l p r e s s u r e
             ·Cable/connector is broken or cable/                                      switch(Measure resistance)
                connector is contacted to battery voltage
                or vehicle ground
             ·Differential pressure switch is defective
※ Some fault codes are not applied to this machine.
                                                                 3-75

--- Page 15 ---
GROUP 2 OPERATIONAL CHECKS AND TROUBLESHOOTING

1. POWER TRAIN OPERATIONAL CHECKS
 This procedure is designed so that the mechanic can make a quick check of the system using a
 minimum amount of diagnostic equipment. If you need additional information, read Structure and
 function, Group 1.
 A location will be required which is level and has adequate space to complete the checks.
 The engine and all other major components must be at operating temperature for some checks.
 Locate system check in the left column and read completely, following the sequence from left to right.
 Read each check completely before performing.
 At the end of each check, if no problem is found(OK), that check is complete or an additional check is
 needed. If problem is indicated(NOT OK), you will be given repair required and group location.
 If verification is needed, you will be given next best source of information :

 Chapter 2 : Troubleshooting
 Group 3 : Tests and adjustments


                                                3-85

--- Page 16 ---
2) DIFFERENTIAL / AXLE
         Problem                          Cause                                           Remedy
Differential low on oil    External leakage.                       Inspect axle and differential for leaks.
Excessive differential Low oil level in differential.              Check oil. Remove drain plug and inspect for
and/or axle noise                                                  metal particles in differential case.
                                                                   Disassemble and determine cause.
                           Incorrect type of oil.                  Change oil
                           Dragging brakes.                        Do brake check.
                           Failed pinion bearing.                  Remove and inspect pinion.
                                                                   Check to ensure pinion housing was indexed.
                           Incorrect gear mesh pattern Remove pinion gear housing and inspect ring
                           between ring and pinion gear. and pinion gear.
                           Failed differential pinion gears Remove differential housing drain plug and
                           and/or cross shafts.             inspect for metal particles. Disassemble and
                                                            inspect.
                           Failed axle bearing.                    Do axle bearing adjustment check.
                           M e c h a n i c a l fa i l u r e i n a x l e Remove differential. Inspect, repair.
                           planetary.
Oil seeping from outer Excessive end play in axle.                 Do axle bearing adjustment check.
axle seal
                       Worn outer bearing and/or cup.              Disassemble and inspect outer axle bearing,
                                                                   cup, spacer, and seal. Replace, if necessary.
                           Overfilled differential.                Check differential oil return system for
                                                                   excessive internal restriction.
Axle overheats             Low differential oil.                   Add oil.
                           Overfilled differential.                See differential overfills with oil in this group.
                           Brake drag.                             See brakes drag in this group.


                                                       3-95

--- Page 17 ---
(1) Fitting of electric control
                                                                   1   1
※ All single parts are to be checked for
  damage and replaced, if required.
  Ensure free travel of the moving parts in
  the valve block prior to installation. Pistons
  can be exchanged individually.
  Prior to the installation, oil single part.
① With the concave side showing upwards,
   insert orifice (1) until contact is obtained.
                                                                                   7709ACV20
 ※ See arrows for installation position.


 ② The opposite figure shows the following
   single parts :
    1 Pressure reducing valve
                                                                                        3
      (1EA, piston and compression spring)
    2 Vibration damper
      (3EA, piston and compression spring)
    3 Follow-on slide
      (3EA, piston and compression spring)                     1           2

                                                                                   7709ACV21


 ③ Install the single parts according to figure
   CV21.
 ※ Preload compression springs of the
   follow-on slides and preliminarily fix
   pistons by means of cylindrical pins
   Ø5.0 mm (assembly aid), see arrows
   (S).                                                                        S


                                                                                   7709ACV22


 ④ Fit two adjusting screws.
                                                                                    2
    Mount seal (1) and housing (2).
                                                           1
    Then position housing equally by means                                          S
    of adjusting screws until contact is                   S
    obtained.
    Adjusting screws (S)          5870 204 036


                                                                                   7709ACV23


                                                   3-105

--- Page 18 ---
(6) Remove the rectangular ring (arrow).


                                                          Figure 9


(7) Press the input shaft out of the spur gear
    bearing. Remove the released bearing
    inner ring and the spur gear.


                                                         Figure10


(8) Press off the bearing inner ring from the
    spur gear.


                                                         Figure11


(9) Remove the converter pressure back-up
    valve.


                                                         Figure 12


                                                 3-115

--- Page 19 ---
(9) Remove the ring.


                                                          Figure 70


(10) Pull off the taper roller bearing.
※ Special tool
  Three-armed puller               5870 971 002


                                                          Figure 71


(11) Squeeze out the snap ring.
     Remove the end shim and the disc set
     K4.


                                                          Figure 72


(12) Preload the compression spring by
     means of fixture.
     Squeeze out the snap ring and the
     released single components.
     Remove the opposite single components
     (K3 side) analogously.
※ Special tool

View the complete manual on HeyDownloads →