PDF Service Manual Hyundai 300D-9 Diesel Forklift - 3 MB

The 2023 service manual for the Hyundai 300D-9 Diesel Forklift provides comprehensive instructions for maintenance and repair.

This detailed guide is essential for technicians, covering everything from the engine and transmission to the hydraulic and electrical systems.

By following the procedures in this manual, you can ensure your Hyundai forklift remains reliable, safe, and productive.

It includes troubleshooting charts, specifications, and detailed diagrams.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
CONTENTS

SECTION 1 GENERAL
  Group 1 Safety hints ------------------------------------------------------------------------------------------------------- 1-1
  Group 2 Specifications --------------------------------------------------------------------------------------------------- 1-5
  Group 3 Operational checkout record sheet ---------------------------------------------------------------- 1-13


SECTION 2 REMOVAL & INSTALLATION
  Group 1 Structure ----------------------------------------------------------------------------------------------------------- 2-1
  Group 2 Removal and installation of unit ---------------------------------------------------------------------- 2-2


SECTION 3 POWER TRAIN SYSTEM
  Group 1 Structure and operation ----------------------------------------------------------------------------------- 3-1
  Group 2 Operation and maintenance --------------------------------------------------------------------------- 3-46
  Group 3 Disassembly and assembly ---------------------------------------------------------------------------- 3-57
  Group 4 Adjustment ------------------------------------------------------------------------------------------------------- 3-185


SECTION 4 BRAKE SYSTEM
  Group 1 Structure and function ------------------------------------------------------------------------------------- 4-1
  Group 2 Operational checks and troubleshooting ------------------------------------------------------- 4-32
  Group 3 Tests and adjustments ------------------------------------------------------------------------------------- 4-40
  Group 4 Disassembly and assembly ---------------------------------------------------------------------------- 4-43


SECTION 5 STEERING SYSTEM
  Group 1 Structure and function ------------------------------------------------------------------------------------- 5-1
  Group 2 Operational checks and troubleshooting ------------------------------------------------------- 5-9
  Group 3 Tests and adjustments ------------------------------------------------------------------------------------- 5-17
  Group 4 Disassembly and assembly ---------------------------------------------------------------------------- 5-21


SECTION 6 HYDRAULIC SYSTEM
  Group 1 Structure and function ------------------------------------------------------------------------------------- 6-1
  Group 2 Operational checks and troubleshooting ------------------------------------------------------- 6-29
  Group 3 Disassembly and assembly ---------------------------------------------------------------------------- 6-34


SECTION 7 ELECTRICAL SYSTEM
  Group 1 Component location ---------------------------------------------------------------------------------------- 7-1
  Group 2 Electrical circuit ------------------------------------------------------------------------------------------------ 7-3
  Group 3 Cluster -------------------------------------------------------------------------------------------------------------- 7-19
  Group 4 Transmission message indication ----------------------------------------------------------------- 7-46

--- Page 3 ---
SECTION 1 GENERAL

Group 1 Safety hints ----------------------------------------------------------------------------------------------------- 1-1
Group 2 Specifications ------------------------------------------------------------------------------------------------- 1-5
Group 3 Operational checkout record sheet ------------------------------------------------------------- 1-13

--- Page 4 ---
5. TORQUE CHART
 Use following table for unspecified torque.
 1) BOLT AND NUT
  (1) Coarse thread
                                        8T                                 10T
     Bolt size
                            kg·m                  lb·ft        kg·m                  lb·ft
     M 6×1.0             0.85 ~ 1.25           6.15 ~ 9.04   1.14 ~ 1.74          8.2 ~ 12.6
     M 8×1.25             2.0 ~ 3.0            14.5 ~ 21.7   2.73 ~ 4.12         19.5 ~ 29.8
     M10×1.5              4.0 ~ 6.0            28.9 ~ 43.4    5.5 ~ 8.3          39.8 ~ 60
    M12×1.75              7.4 ~ 11.2           53.5 ~ 79.5    9.8 ~ 15.8           71 ~ 114
     M14×2.0             12.2 ~ 16.6           88.2 ~ 120    16.7 ~ 22.5          121 ~ 167
     M16×2.0             18.6 ~ 25.2            135 ~ 182    25.2 ~ 34.2          182 ~ 247
     M18×2.5             25.8 ~ 35.0            187 ~ 253    35.1 ~ 47.5          254 ~ 343
     M20×2.5             36.2 ~ 49.0            262 ~ 354    49.2 ~ 66.6          356 ~ 482
     M22×2.5             48.3 ~ 63.3            350 ~ 457    65.8 ~ 98.0          476 ~ 709
     M24×3.0             62.5 ~ 84.5            452 ~ 611    85.0 ~ 115           615 ~ 832
     M30×3.0             124 ~ 168              898 ~ 1214   169 ~ 229           1223 ~ 1655
     M36×4.0             174 ~ 236             1261 ~ 1703   250 ~ 310           1808 ~ 2242


  (2) Fine thread
                                        8T                                 10T
     Bolt size
                            kg·m                  lb·ft        kg·m                  lb·ft
    M 8×1.0              2.17 ~ 3.37           15.7 ~ 24.3   3.04 ~ 4.44         22.0 ~ 32.0
    M10×1.25             4.46 ~ 6.66           32.3 ~ 48.2   5.93 ~ 8.93         42.9 ~ 64.6
    M12×1.25             7.78 ~ 11.58          76.3 ~ 83.7   10.6 ~ 16.0         76.6 ~ 115
    M14×1.5              13.3 ~ 18.1           96.2 ~ 130    17.9 ~ 24.1          130 ~ 174
    M16×1.5              19.9 ~ 26.9            144 ~ 194    26.6 ~ 36.0          193 ~ 260
    M18×1.5              28.6 ~ 43.6            207 ~ 315    38.4 ~ 52.0          278 ~ 376
    M20×1.5              40.0 ~ 54.0            289 ~ 390    53.4 ~ 72.2          386 ~ 522
    M22×1.5              52.7 ~ 71.3            381 ~ 515    70.7 ~ 95.7          512 ~ 692
    M24×2.0              67.9 ~ 91.9            491 ~ 664    90.9 ~ 123           658 ~ 890
    M30×2.0              137 ~ 185              990 ~ 1338   182 ~ 248           1314 ~ 1795
    M36×3.0              192 ~ 260             1389 ~ 1879   262 ~ 354           1893 ~ 2561


                                                  1-10

--- Page 5 ---
⑤ Slowly raise inner mast upright until mast
   clears top of fork carriage. Move carriage           Inner mast
   to work area and lower the mast.
                                                      Middle mast
    Make sure that carriage remains on
    floor and does not bind while mast is
    being raised.
 ⑥ Inspect all parts for wear or damage.
                                                                                       Outer
   Replace all worn or damaged parts.                                                  mast


                                                                   Block


                                                            Free lift
                                                             chain


                                                                                        Lift
                                                                                        chain


                                                        Carriage


                                                                                       300D9RE56E


(3) Piping
                                                                Middle mast
 ① Remove the main hose attached to the
   work attachment.
 ② Remove the hoses from the work
   attachment.                                            Free
 ③ Remove the lowing safety valve.                          lift                   Outer
                                                      cylinder                     mast
 ※ Put blind plugs in the piping immediately
   after removing pipes.
   This prevents the hydraulic oil from                                            A
                                                                           A
                                                                                        B
   flowing out and also prevents dust and                                      B
   dirt from getting in.                                                   C
                                                           Lift
                                                      cylinder                     C

                                                                               D            D


                                                        Outer
                                                        mast


                                                                                       300D9RE57E


                                                2-4

--- Page 6 ---
3. ENGINE
  Remove the torque converter, transmission and front axle inside the frame, then remove the engine
  assembly
 1) REMOVAL

                                  T/C housing              Mounting bolts
                                     cover                holding to engine
                                                               flywheel
             Engine
              hood
                                    Engine
                                   accessory


                                    Shroud                                     Mounting bolts


             Cabin                  Radiator
                                     hose


                                   Air cleaner
                                      hose
                                                                                                 250D9RE25


  (1) Engine hood
   ① Cabin                                                                Mounting bolt
                                                             Crane       Engine
     - First, tilt the cabin                                            cover(RH)
     ※Refer to page 7-17 of operator's
        manual for operating description.
     - After remove the wiring for rear
                                                                                          Engine cover
       combination lamp, work lamp, head                                                      (LH)
       lamp and flasher lamp on the stay of
       the cabin and then raise it with a crane.
     - Finally remove cabin for tilt option
       cylinder, pin and latch assy.
   ② Engine cover (LH, RH)
     Remove engine cover by loosening the
     mounting bolts.
                                                                                                300D9RE17E


                                                   2-14

--- Page 7 ---
3. TRANSMISSION
 1) LAYOUT


                                                                    2              4
           Gearbox diagram
                                                                                            3


                                                                                                    1
                  KR
                                              8

      KV                      K4

               AN/PTO


                             K1
      K2

               K3/AB

                                                  5


                                                             6
                                                                           7

                                                                                            180D7ETM03


  1   Clutch shaft (lay shaft, K4)                      5   Clutch shaft (KZ)
  2   Clutch shaft (KV)                                 6   Clutch shaft / Output (K3/AB)
  3   Input shaft / Power take-off (AN/PTO)             7   Clutch shaft (K1)
  4   Clutch shaft (KR)                                 8   Electro-hydraulic control


                                                  3-5

--- Page 8 ---
2) DISPLAY DURING AEB-MODE

      Symbol                     Meaning                                          Remarks
K1......K3       Calibrating clutch K1...K3, KV or KR
KV, KR           resp.
_and Kx          Wait for start, initialization of clutch
                 Kx, x : 1, 2, 3, V, R
≡and Kx          Fast fill time determination of clutch Kx
=and Kx          Compensating pressure determination
                 of clutch Kx
OK               Calibration for all clutches finished       Transmission stays in neutral, you have to restart
                                                             the TCU (ignition off/on) after removing AEB-Starter
STOP             AEB canceled(activation stopped)            Transmission stays in neutral, you have to restart
                                                             the TCU (ignition off/on)
STOP and Kx      AEB stopped, clutch Kx can't be Transmission stays in neutral, you have to restart
                 calibrated                      the TCU (ignition off/on)
Spanner and Kx   Kx couldn't be calibrated, AEB Transmission stays in neutral, you have to restart
                 finished                       the TCU (ignition off/on)
△E               Engine speed too low
                 → raise enging speed
▽E               Engine speed too high
                 → lower enging speed
△T               Transmission oil temperature too
                 low → heat up transmission
▽T               Transmission oil temperature too
                 high → cool down transmission
FT               Transmission temperature not in Transmission stays in neutral, you have to restart
                 defined range during calibration the TCU (ignition off/on)
FB               Operating mode not NORMAL or Transmission stays in neutral, you have to restart
                 transmission temperature sensor the TCU (ignition off/on)
                 defective or storing of Calibrated
                 values to EEPROM-has failed.
FO               Output speed_not_zero                       Transmission stays in neutral, you have to restart
                                                             the TCU (ignition off/on)
FN               Shift lever not in Neutral position         Transmission stays in neutral, you have to restart
                                                             the TCU (ignition off/on)
FP               Park brake_not_applied                      Transmission stays in neutral, you have to restart
                                                             the TCU (ignition off/on)
STOP             AEB-Starter was used incorrect or Transmission stays in neutral, you have to restart
                 is defective. Wrong device or wrong the TCU (ignition off/on)
                 cable used.


                                                      3-15

--- Page 9 ---
Fault code          Meaning of the fault code
  (Hex)          possible reason for fault detection           Reaction of the TCU                Possible steps to repair

   88        S.C. to ground at clutch KR                     TCU shifts to neutral           · Check the cable from TCU to the
             The measured resistance value of the valve OP mode : Limp home                    gearbox
             is out of limit, the voltage at KR valve is too If failure at another clutch is · Check the connectors from
             low                                             pending                           gearbox to TCU
             ·Cable/connector is defective and has TCU shifts to neutral                     · Check the regulator resistance*
                contact to vehicle ground                    OP mode : TCU shutdown          · Check internal wire harness of the
             ·Regulator has an internal defect                                                 gearbox
                                                                                               * See page 3-36
   89        O.C. at clutch KR                        TCU shifts to neutral           · Check the cable from TCU to the
             The measured resistance value of the OP mode : Limp home                   gearbox
             valve is out of limit                    If failure at another clutch is · Check the connectors from
             ·Cable/connector is defective and has no pending                           gearbox to TCU
               contact to TCU                         TCU shifts to neutral           · Check the regulator resistance*
             ·Regulator has an internal defect        OP mode : TCU shutdown          · Check internal wire harness of the
                                                                                        gearbox
                                                                                        * See page 3-36
   91        S.C. to ground at relay reverse warning Backup alarm will be on until · Check the cable from TCU to the
             alarm                                         TCU power down even if fault   backup alarm device
             TCU detected a wrong voltage at the vanishes(Loose connection) · Check the connectors from
             output pin, that looks like a S.C. to vehicle OP mode : Normal               backup alarm device to TCU
             ground                                                                     · Check the resistance* of backup
             ·Cable is defective and is contact to                                        alarm device
               vehicle ground                                                             * See page 3-36
             ·Backup alarm device has an internal
               defect
             ·Connector pin is contacted to vehicle
               ground
   92        S.C. to battery voltage at relay reverse No reaction                       · Check the cable from TCU to the
             warning alarm                                 OP mode : Normal               backup alarm device
             TCU detected a wrong voltage at the                                        · Check the connectors from
             output pin, that looks like a S.C. to battery                                backup alarm device to TCU
             voltage                                                                    · Check the resistance* of backup
             ·Cable is defective and is contacted to                                      alarm device
               battery voltage                                                            * See page 3-36
             ·Backup alarm device has an internal
               defect
             ·Connector pin is contacted to battery
               voltage


                                                               3-24

--- Page 10 ---
Fault code          Meaning of the fault code
  (Hex)          possible reason for fault detection       Reaction of the TCU             Possible steps to repair

   E1        S.C. battery voltage at speedometer                    -               ※ Not used
             output
   E2        S.C. to ground or O.C at speedometer                                   ※ Not used
             output                                                 -

   E3        S.C. to battery voltage at display output No reaction                  · Check the cable from TCU to the
             TCU sends data to the display and OP mode : Normal                       display
             measures always a high voltage level on                                · Check the connectors at the
             the connector                                                            display
             ·Cable or connectors are defective and                                 · Change display
               are contacted to battery voltage
             ·Display has an internal defect
   E4        S.C. to ground at display output        No reaction                    · Check the cable from TCU to the
             TCU sends data to the display and OP mode : Normal                       display
             measures always a high voltage level on                                · Check the connectors at the
             the connector                                                            display
             ·Cable or connectors are defective and                                 · Change display
               are contacted to battery voltage
             ·Display has an internal defect
   E5        Communication failure on DeviceNet        Shift to neutral             · Check Omron master
                                                       OP mode : TCU shutdown       · Check wire of DeviceNet-Bus
                                                                                    · Check cable to Omron master
   E5        DISPID1 timeout                          TCU select parameter set with · Check display controller
             Timeout of CAN-massage DISPID1 from ID0                                · Check wire of CAN-Bus
             display controller                       OP mode : Limp home           · Check cable display controller
             ·Interference on CAN-Bus
             ·CAN wire/connector is defective
             ·Can wire/connector is defective and has
               contact to vehicle ground or battery
               voltage


                                                          3-34

--- Page 11 ---
3) STRUCTURE 3


                                                                                               336
                                                                                         338
                                                                                      337


                                                     331          333
                                               324
                                        322
                                  324

                      329                                                                            335
                                                                                    320
             340                                                            318


                                                                 314

     300                                                   319
                                                     309


                                              304
   306
305

                  308
               307          312

                                                                                                       250D7EDR04


  300    Planetary housing              314    Sun gear                  331      Planetary pin
  304    O-ring                         318    Sleeve                    333      Locking pin
  305    Screw plug                     319    Hexagon socket screw      335      Ring gear
  306    Sealing ring                   320    Thrust ring               336      Ring gear carrier
  307    Screw plug                     322    Planetary gear            337      Retainer
  308    Sealing ring                   324    Thrust washer             338      Hexagon screw
  309    Thrust washer                  329    Needle bearing            340      O-ring
  312    Hexagon socket screw


  4) OPERATION
    Both sides of the housing are supported by the frame and the center is mounted on the
    transmission case through propeller shaft.
    The mast is installed on the front of the frame. The final deceleration and differential device built in
    the housing guarantee accurate rotation and smooth operation.
    The power from the transmission in transferred through the pinion, ring gear, differential case, the
    pinion of the differential device and the side gear to the drive axle shaft by the side gear spline and
    to the hub and wheel mounted on the shaft by high tension bolts.


                                                       3-44

--- Page 12 ---
3. TROUBLESHOOTING
 1) BRAKE LEAKS ACTUATION FLUID

       Condition                     Possible cause                                   Correction

Internal leak : Fluid     1. Worn or damaged piston seal.       1. Replace piston seals.
bypasses seals into axle 2. Melted or extruded piston seals. 2. Correct cause of overheating and replace
and fills axle with fluid                                          seals.
and blows out breather 3. Corrosion, pitting, wear or other
                             damage, marks, scratches to        3. Clean, smooth, rework or replace affected
or empties brake fluid
                             piston and/or brake  housing  bore    parts.
reservoir.
                             in area of seal/sealing lips.
External leak             1. Loose bleeder screw.                1. Tighten bleeder screw to 2.0~2.7 kgf·m (15~20
                                                                    lb-ft)
                          2. Loose inlet fitting or plugs.
                                                                 2. Tighten inlet fitting to 3.4~4.8 kgf·m (25~35 lb-ft)
                          3. Damaged inlet fitting or plugs or
                             damaged seats.                      3. Replace inlet fitting or plug and O-ring if used.


 2) BRAKE NOISE AND VIBRATION

       Condition                     Possible cause                                   Correction

Brakes product noise,     Incorrect axle fluid and/or friction   1. Use only meritor specified or approved
chatter, vibration.       material used.                            materials.
                                                                 2. Drain and flush fluid from axle. Replace with
                                                                    approved fluid.
                                                                 3. Replace all friction discs. Thoroughly clean
                                                                    or replace stationary discs.


                                                        3-54

--- Page 13 ---
3) E N G I N E C O N N E C T I O N A N D O I L
   PRESSURE PUMP
 (1) Engine connection                                          2
                                                        1
     Loosen two hex screws (2), fit eye bolts
     (1) and pull off converter by means of
     lifting device.
  ① Separate flexplate (3) from converter.                              3

    (S) Eye bolts assortment 5870 204 002
    (S) Lifting chain        5870 281 047                               180DTM034


  ② Loosen threaded connection converter
    bell-housing/transmission housing and
    remove converter bell-housing (1).
                                                                        1


                                                                        180DTM035


  ③ Remove O-ring (1).

    Loosen threaded connection plate/                               2
    transmission housing and oil pressure                   1
    pump/transmission housing, then
    remove plate (2).


                                                                        180DTM036


                                                 3-64

--- Page 14 ---
(2) Clutch KR
 ① Unsnap piston ring (1).                              1


                                                            180DTM068


 ② Pull tapered roller bearing (internal ring)
   off the shaft.
                                                        S
   (S) Forcing device           5870 026 100
   (S) Grab sleeve              5873 001 059


                                                            180DTM069


 ③ Unsnap retaining ring (1).
                                                        1
   (S) Set of external pliers   5870 900 015


                                                            180DTM070


 ④ Pull clutch (1) together with spur gear off
   the shaft.
   (S) Two-armed puller         5870 970 004


                                                        1


                                                            180DTM071


                                                 3-74

--- Page 15 ---
⑨ Preload cup springs and remove L-ring
  (1).
                                                                  1
  (S) Assembly aid         5870 345 088


                                                               180DTM059


⑩ Remove guide ring (1) and cup spring
                                                   1
  package (2).

                                                   2


                                                               180DTM082


⑪ Lift piston (1) off the disc carrier by
  compressed air out of hole, and remove
  it.                                                  1


                                                               180DTM061


⑫ Remove both O-rings (1 and 2).

                                                   1

                                                           2


                                                               180DTM062


                                            3-84

--- Page 16 ---
⑤ Mount stud bolt (1).
                                                         1
  Tightening torque (M10/8.8×16)
                             MA =1.7 Nm


                                                                 180DTM112


⑥ Insert ball bearing 55×90×18 (2) into
  idler gear (1) until contact is obtained           3
  and fix it by means of retaining ring (3)
                                                     2
  90×3.
  (S) Set of internal pliers   5870 900 013
                                                             1


                                                                 180DTM113


⑦ Heat up ball bearing (app. 120°C).

  (S) Hot air blower 230 V     5870 221 500
  (S) Hot air blower 115 V     5870 221 501


                                                                 180DTM114


⑧ Mount pre-assembled idler gear (1) until
  contact.
  Wear protective gloves.
                                                             1


                                                                 180DTM115


                                              3-94

--- Page 17 ---
21 Fix clutch (1) by means of retaining ring
                                                        2
  55×2 (2).


                                                                1


                                                                180DTM134


22 Heat up bearing inner ring (approx. 120
  °C).


                                                                180DTM135


23 Mount bearing inner ring (1) until contact
  is obtained.                                              1
  Wear protective gloves.
※ Adjust bearing inner ring after cooling-
  down.
  Check closing and opening of the clutch
  by means of compressed air at the hole
  (see arrow).
  Closing and opening of the clutch must                        180DTM136

  be clearly audible.


                                                3-104

--- Page 18 ---
⑬ Heat up internal diameter of clutch (app.
  120 °C).
  (S) Hot air blower 230 V 5870 221 500
  (S) Hot air blower 115 V 5870 221 501


                                                                  180DTM126


⑭ Mount clutch until contact is obtained.

  Wear protective gloves.


                                                      1


                                                                  180DTM151


⑮ Mount and oil running disc 55×78×5
                                                              3
  (1), axial cage (2) and axial washer
                                                          2
  55×78×1 (3).
                                                              1
※ Install running disc (see arrow) with
  chamfer (see arrow) showing towards
  the axial cage.


                                                                  180DTM152


16 Mount needle cage 55×63×50 (1) on
  shaft and oil it.                                       1


                                                                  180DTM153


                                              3-114

--- Page 19 ---
(7) Input shaft
                                                                      1
 ① Install snap ring SB-38 (1) into annular
    groove of turbine shaft (2).


                                                                      2


                                                                              180DTM173


 ② Press turbine shaft (1) into the input shaft
    (2) under a handoperated press until
    snap ring engages into the groove.                            F
                                                              1
 ※ Axial fixture of turbine shaft.


                                                          2


                                                                              180DTM174


 ③ Heat up both bearing inner rings (app.
    120 °C).
    (S) Hot air blower 230 V 5870 221 500
    (S) Hot air blower 115 V 5870 221 501


                                                                              180DTM135


 ④ Mount bearing inner rings (1) until
    contact.
    Install rectangular ring (2) 60×3.
    Wear protective gloves.
 ※ Readjust bearing inner ring after cooling                              2
                                                          1
    down.


                                                                              180DTM175


                                                  3-124

--- Page 20 ---
9) REASSEMBLY ENGINE CONNECTION
   AND OIL PRESSURE PUMP
(1) Oil pressure pump :
 ※ In case of wear marks in the pump
    housing or on the control disk, the pump
    assy must be replaced.
 ① Install outer rotor.
 ※ Chamfer (see arrow) to show
                                                                     180DTM201
    downwards.


 ② Install inner rotor.
 ※ Teeth (see arrow) to show upwards.


                                                                     180DTM202


 ③ Place control disk and fix it radially by
                                                         1
    means of two cylindrical screws M6×12
    (1).
 ※ Do not tighten the cylindrical screws-just
    turn them in until contact is obtained and
    then turn them back by approx 1/2
    rotation.
                                                                        2
    Pay attention to the installation position
    of the control disk, see figure.
                                                                     180DTM203
    Place O-ring 182×3 (2) into the annular
    groove and oil it.


 ④ With the sealing lip showing downwards,
    carefully insert the shaft seal
    75×905×10 (1) into the pump housing
    (2) until contact is obtained.
                                                             1
 ※ Wet outer diameter of shaft seal with
    spirit.

View the complete manual on HeyDownloads →