PDF Service Manual Gehl V420 & Mustang 4200V Skid Steer Loader - 32 MB

This detailed service manual covers both the Gehl V420 and Mustang 4200V skid steer loaders, providing technicians with all the information needed for professional-level repairs and maintenance.

The manual includes sections on the engine, hydraulics, electrical systems, and powertrain.

With clear instructions and diagrams, this guide helps you diagnose problems quickly and perform repairs to factory standards.

It is an essential tool for keeping these powerful machines running smoothly.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
Gehl V420
Mustang 4200V
                     Form No.
                     50950421
                     Revision A
                       12/18


SKID-STEER LOADERS


                        Service Manual

--- Page 3 ---
GEHL V420 / MUSTANG 4200V                                                                                     SAFETY

Machines Equipped with Air Conditioning                       Lift Arm Support Device
This product contains
R134a which is a
fluorinated greenhouse
gas with a Global
Warming Potential of
                                                                                     WARNING
1430. The decal shown                                         BEFORE leaving operator’s compartment to
indicates the amount of                                       work on the loader with the lift arm raised,
R134a gas contained                                           ALWAYS engage the lift arm support device.
within the machine’s A/C system and its corresponding         Turn the keyswitch to OFF, remove the key and
CO2e. “CO2e” means CO2 equivalent. The decal is               take it with you.
located within the engine compartment and is
                                                              Many service procedures require a raised lift arm to
positioned adjacent to the A/C system components that
                                                              allow easier access to loader components. For operator
contain the R134a gas.
                                                              and service personnel safety, a lift arm support device is
Do not allow the R134a gas to be discharged from the          standard on Gehl and Mustang skid-steer loaders. Used
machine A/C system into the atmosphere when                   as a cylinder block, it helps prevent a raised lift arm
performing service and maintenance on this machine.           from unexpectedly lowering.
                                                              BE SURE to engage the lift arm support device
Mandatory Safety Shutdown Procedure                           whenever the lift arm is raised. When the device is not
BEFORE cleaning, adjusting, lubricating or servicing          being used, secure it to the left rear of the lift arm using
the unit or leaving it unattended:                            the lynch pin provided.

1. Move drive control handle(s) to the neutral position.      The lift arm support device is a safety device which
                                                              must be kept in proper operating condition at all times
2. Lower the lift arm and attachment completely. If the       with decals in place.
lift arm must be left in the “raised” position, BE SURE
to properly engage the lift arm support device.               The following procedures outline the correct way to
                                                              engage and disengage the lift arm support device.
3. Move the throttle to the low idle position, shut off the
engine and remove the key.                                    Lift Arm Support Device Engagement
4. Before exiting, move the lift/tilt control(s) to verify
that controls do not cause movement of the lift arm or        1. Remove attachment from lift arm.
hitch.                                                        2. Raise the lift arm fully.
Only after these precautions can you be sure it is safe to    3. Turn keyswitch to OFF position to stop engine.
proceed. Failure to follow the above procedure could
                                                              4. Have an assistant remove the lift arm support
lead to death or serious injury.
                                                                 device from its storage location and place the lift
                                                                 arm support device on the left cylinder rod and
                                                                 secure with chain provided.


                                                                   Lynch Pin and Chain


PRINTED IN USA                                     50950421/A1218                                                       5

--- Page 4 ---
GEHL V420 / MUSTANG 4200V                                                                         MAINFRAME

                Introduction                              sprockets. Oil is used inside these cases to ensure the
                                                          chains always receive proper lubrication.
Gehl V420 and Mustang 4200V model skid-steer              The lift arm and the lift and tilt cylinders are mounted
loaders have a welded steel chassis. Maintenance,         with pivot pins. Capscrews are used to secure the pivot
service and repair may be performed through standard      pins. A Rollover Protective Structure/Falling Object
access panels.                                            Protective Structure (ROPS/FOPS) is standard for
Two side chaincases provide mounting for the drive        operator safety, and both the seat and restraint bar
motors and for the front and rear axles. The side cases   include safety interlock switches.
also serve as sealed housings for the drive chains and

 Mainframe - Chassis Components


                                                                             3    LN 5/16 CBZY
                                                                             4    CS FL LOCK 3/8X1 C5ZY
                                                                             5    CS FL LOCK 5/16X3/4 C5ZY
                                                                             7    CS FL LOCK 1/2X1-1/4 C5ZY
                                                                             9    PLUG MORB12
                                                                             11   COVER/TOEPLATE
                                                                             14   BREATHER/ 3/4"NPT
                                                                             15   WLDMT/STEP
                                                                             25   CAP/FUEL FILLER
                                                                             26   STRAINER/FUEL
                                                                             34   ASSY/COVER/REAR RH
                                                                             35   ASSY/COVER/FRONT RH
                                                                             38   COVER/CHASSIS
                                                                             39   ASSY/COVER/FRONT LH
                                                                             40   COVER/FLOOR PLATE
                                                                             43   ASSY/COVER/REAR LH
                                                                             46   BRACE/TOWER
                                                                             55   WLDMT/SEAL/RT
                                                                             56   WLMT/SEAL/LEFT
                                                                             57   SECTION/RETAINING RING
                                                                             58   SEAL/PAD
                                                                             59   SEAL/PAD
                                                                             60   SEAL/CHASSIS
                                                                             63   PLATE/FLOOR
                                                                             64   HOLD DOWN/BATTERY LH
                                                                             65   HOLD DOWN/BATTERY RH
                                                                             69   CS 1/2X1-1/4 C5ZY
                                                                             72   HWHMS 3/8X3/4 C2ZY
                                                                             73   CS FL 5/16X2 C8ZY
                                                                             76   BHSCS 1/2X 1-1/2 C8 OCB
                                                                             78   HWHTRS TAP/R 5/16X3/4 CZY
                                                                             81   CS FL 5/16X1 C5ZY
                                                                             85   PLUG MP08


PRINTED IN USA                                 50950421/A1218                                                  15

--- Page 5 ---
GEHL V420 / MUSTANG 4200V                                              MAINFRAME


 HVAC Assembly - Front - ROPS/FOPS


                                                      19 SCREW/#8 X .5 SM/PHIL FH
                                                      32 VENT
                                                      34 PLUG/PASS-THROUGH TUBE
                                                      35 TUBE/FORWARD HVAC
                                                      36 COVER/RECIRC
                                                      46 CLIP/HOSE RETAINING
                                                      100 PHMS CR 1/4X3/4 OCB


PRINTED IN USA                       50950421/A1218                                 25

--- Page 6 ---
GEHL V420 / MUSTANG 4200V                                       MAINFRAME


 Power-A-Tach® Components - Chassis


                                                   1    HLN INST 5/16 CZY
                                                   2    HLN INST 1/4 CZY
                                                   3    ST MJ08-MORB06
                                                   4    CS FL LOCK 3/8X3/4 C5ZY
                                                   5    PLATE/TOP SIZE 2 TWIN
                                                   7    CLAMP/TUBE .50 TWIN
                                                   9    BAR/HOSE PIVOT LINKAGE
                                                   10   TIE/CABLE .50X12.90 BLACK
                                                   12   SPACER/CLAMP
                                                   13   HOSE/ASSY/.50 X 76.50
                                                   17   WLDMT/TUBE MOUNT
                                                   18   TUBE/ALLTACH/HYD
                                                   19   TUBE/ALLTACH/HYD
                                                   20   WLDMT/HOSE PIVOT
                                                   21   BAND
                                                   22   TUBE/HOSECARRIAGE
                                                   26   WLDMT/ARM/CARRIAGE
                                                   27   ALLTACH/COIL KIT
                                                   28   CLAMP/HYD HOSE
                                                   29   BAND/HYD HOSE
                                                   30   BAND/HYD HOSE/BASE
                                                   31   BUSHING/0.275X0.118
                                                   33   BUSHING/.313X.75
                                                   42   CS 5/16X2 C5ZY
                                                   44   CS 5/16X2-1/2 C5ZY
                                                   46   CS 1/4X3-3/4 C5ZY
                                                   47   CB 1/4X2-1/4 C5ZY
                                                   48   CB 1/4X3-3/4 C5ZY


PRINTED IN USA                    50950421/A1218                               35

--- Page 7 ---
GEHL V420 / MUSTANG 4200V                                                                         MAINFRAME

NOTE: After removing/replacing any components of
the lift and tilt system, ALWAYS prime hydraulic                                       A
system by operating the lift arm and attachment (NO
LOAD) slowly up and down for several cycles. Check
system for hydraulic oil leaks. Fill the hydraulic
reservoir until fluid becomes visible on the hydraulic oil
dipstick.
                                                                                      B
NOTE: Refer to the lift arm bushing installation
procedure in     this   chapter   if   bushings   require
replacement.

Rear Link Removal and Installation
                                                             Fig. 31 – Rear Link Capscrews and Locknuts
                                                             5. Remove the capscrew and washer (C, Fig. 32) from
                        WARNING                                 the upper rear timing link pivot pin. Repeat this
                                                                step for the opposite side.
BEFORE continuing this service procedure,
perform the following SAFETY procedures:
• Shut off the engine and remove the key.
• Raise the loader, block and remove the tires.
• Procure two suitable hoist systems.
(For detailed instructions, refer to the Safety
chapter of this manual.)

Removal Procedure
                                                                                              C
1. Raise the lift arm to a height of 6 ft. (1.8 m) and
   secure it in place with an appropriate lifting device.
2. Complete the mandatory safety shutdown
   procedure.                                                Fig. 32 – Pivot Pin Capscrew and Washer

3. Raise and support the rear of the machine with an
   appropriate supporting device. Remove the rear
   wheels from the machine.
4. Attach an appropriate lifting device to the rear link
                                                                                WARNING
                                                             Lift arm may shift or move when the rear arm
   (A, Fig. 31) and remove the two capscrews and
                                                             pivot pins are removed.
   locknuts (B).


PRINTED IN USA                                    50950421/A1218                                              45

--- Page 8 ---
GEHL V420 / MUSTANG 4200V                                                                       MAINFRAME

Fuel Sensor Removal and Installation                      Rear Grille Removal and Installation
Removal Procedure                                         The rear grille is pinned onto the chassis and can be
                                                          removed to perform work on the cooling system,
                                                          engine, engine fan and shrouds.

                     WARNING                              Removal Procedure
                                                          1. Raise the engine access cover.
BEFORE beginning this service procedure,
perform the following SAFETY procedures:                  2. Push down the rear grille latch (A, Fig. 50) and
                                                             open the rear grille.
• Shut off the engine and allow it to cool.
(For detailed instructions, refer to the Safety
chapter of this manual.)

1. Remove the lower right radiator hose from the
   engine and unplug the sensor (below).
2. Remove the five screws securing the bracket and
   sensor, then remove the sensor and gasket from the
   tank.                                                                           A


                                                           Fig. 50 – Rear Grille Latch
                                                          3. Disconnect the taillight electrical connector (B,
                                                             Fig. 51), located between the charge air cooler and
                                                             the lower rear grille hinge.


Installation Procedure
1. Clean old gasket adhesive off fuel tank.
2. Install new gasket using Form-A-Gasket #765-
   1211 (or equivalent) to seal sensor opening on fuel
   tank.
                                                                                                     B
3. Install the sensor in the fuel tank.
4. Install the sensor electrical plug to the sensor.
5. Install the five screws through the sensor into the
   fuel tank. DO NOT OVERTIGHTEN.
                                                          Fig. 51 – Taillight Electrical Connector


PRINTED IN USA                                    50950421/A1218                                                55

--- Page 9 ---
GEHL V420 / MUSTANG 4200V                                                                   WHEEL DRIVES

4. Place the axle shaft on a flat surface with the shaft   6. Press another inner bearing cone onto the axle
   in a vertical position. Press the inner bearing cone       shaft. Note the proper orientation of the second
   onto the axle shaft with a suitable driver or a press      inner bearing cone.
   at a force of 6000 lbf. (26,7 kN). Note the proper
   orientation of the first bearing cone.

                     Bearing Cone


                                                           7. Spread the bearing grease around the cone surface.


                                                           8. Install a new o-ring on the axle housing assembly
                                                              and secure it with grease.
5. Place axle housing onto axle shaft.


PRINTED IN USA                                  50950421/A1218                                               65

--- Page 10 ---
GEHL V420 / MUSTANG 4200V                                                                                CONTROLS

7. Block ports A and B ports and apply the parking           Electrical Foot Throttle Removal and
   brake.                                                    Installation
8. Start the machine observing safety practices.             Gehl V420 and Mustang 4200V machines have an
9. Loosen the jam nuts on the neutral adjustment             electric foot throttle located beside the right foot rest for
   screws.                                                   increasing/decreasing the engine speed.
10. Turn the mechanical centering adjusting screw            Removal Procedure
    until 1000 psi (70 bar) is read on the pressure ports.
11. Turn the screw back, splitting the distance between
    the previous two positions.
Note: Pressure on MA and MB should be equal.
                                                                                   WARNING
12. Tighten the jam nut on the adjustment screws when        BEFORE beginning this service procedure,
    equal pressure is measured on both gauges.               perform the following SAFETY procedures:
13. Stop the pump drive.                                     • Remove attachment from lift arm.
14. Remove the hose connecting ports X1 and X2.              • Raise lift arm; engage lift arm support device.
    Reinstall plugs where MA and MB were checked.            • Shut off the engine.
15. Adjust NEUTRAL in the other section, if neces-           (For detailed instructions, refer to the Safety
    sary.                                                    chapter of this manual.)

                                                             1. Remove the front kickplate cover just below the
                                                                cab entry step.


                                                                                    Kickplate Cover


PRINTED IN USA                                    50950421/A1218                                                      75

--- Page 11 ---
GEHL V420 / MUSTANG 4200V                                                       HYDROSTATIC SYSTEM

3. Remove the capscrews (35 lbf.) (47 N•m) attaching     Drive Motor Removal and Installation
   the flexible coupling plate to the engine. Use Loc-
   tite™ 242 or equivalent to reinstall.

                                                                            WARNING
                                                         BEFORE beginning this service procedure,
                                                         perform the following SAFETY procedures:
                                                         • Remove attachment from lift arm.
                                                         • Raise and securely block the loader so all
                                                         four tires are off the ground.
                                                         • Raise lift arm; engage lift arm support device.
                                                         • Shut off the engine.
                                                         • Tilt back ROPS/FOPS until lock engages.
                                                         (For detailed instructions, refer to the Safety
                                                         chapter of this manual.)
Installation Procedure - Follow all warnings first,
then reverse the removal steps.                          Removal Procedure
                                                         1. Underneath the skid-steer loader, remove the cap-
                                                            screws securing the belly pans and then remove
                                                            both pans from the chassis.


                                                         2. Remove the drive chains per the procedure in the
                                                            Wheel Drives chapter.
                                                         3. If necessary, drain oil from the hydraulic reservoir
                                                            and chaincases per their procedures in the Lubrica-
                                                            tion chapter.
                                                         NOTE: If the hydraulic hoses and tubes are plugged
                                                         after removal to prevent oil leakage, it should not be
                                                         necessary to drain the hydraulic reservoir. Hydraulic
                                                         hoses and tubes, along with the auxiliary suction hose
                                                         and other components should be plugged to prevent
                                                         contaminants from entering the hydraulic system.
                                                         4. BEFORE disconnecting hydraulic hoses and tubes
                                                            from the drive motor, mark each hose/tube and the
                                                            port where it attaches to the drive motor (so that


PRINTED IN USA                                50950421/A1218                                                 85

--- Page 12 ---
GEHL V420 / MUSTANG 4200V                                                                      HYDRAULIC SYSTEM

                    Introduction                                  The following troubleshooting guide lists potential
                                                                  hydraulic system problems, as well as possible causes
This chapter covers troubleshooting, testing, removal,            and remedies, for Gehl V420 and Mustang 4200V skid-
installation and adjustment procedures for hydraulic              steer loaders.
system components on Gehl V420 and Mustang 4200V                  If you cannot locate a particular hydraulic system
model skid-steer loaders.                                         problem in this chart, consult the Hydrostatic System
Power for the lift arm functions and auxiliary hydraulics         chapter troubleshooting chart or call a Service
is provided by a axial piston pump attached to the front          technician.
of the tandem pump. An additional gear pump provides              When a problem occurs, don’t overlook simple causes.
oil for fan and All-Tach® functions.                              A malfunction could be caused by something as simple
Machines include a standard-flow auxiliary hydraulics             as low fluid level in the hydraulic reservoir. After a
system with connections on the lift arm for attachment            mechanical failure has been corrected, be sure to locate
hookup. They are also equipped with high-flow                     the cause of the problem.
hydraulics, which includes connectors on the right side
of the lift arm, for operating attachments that require
higher hydraulic flow.                                                       IMPORTANT
Information on recommended hydraulic fluids,                      DO NOT attempt to service or repair major
capacities and filter change intervals is in the                  hydraulic system components, such as the
Lubrication chapter. For detailed information on axial-           pump, unless authorized to do so by your Gehl
piston pump or control valve internal repair, consult the         or Mustang dealer. Any unauthorized repair
Gehl-Mustang Service Department and/or the hydraulic              will void the warranty.
component manufacturer’s service manual. Hydraulic
components related to the drive system are covered in
the Hydrostatic System chapter.
                                        Troubleshooting Guide
                 Problem                          Possible Cause                                    Remedy
 Lift/tilt controls fail to respond     Hydraulic oil viscosity too heavy           Allow longer warm-up or replace with
                                                                                    proper viscosity oil.

                                        Hydraulic oil level low                     Check oil level in reservoir. If oil is low,
                                                                                    check for an external leak. Repair and
                                                                                    add oil.

                                        Hydraulic oil flow to the pump blocked      Inspect suction hose. Clean or replace
                                                                                    as needed.

                                        Inlet relief valve malfunctioning           Adjust or replace relief valve as needed
                                                                                    in the control valve.

                                        Drive disconnected                          Check for broken or worn pump drive
                                                                                    coupling. Replace as needed.

                                        Sheared spline or broken shaft in           Check splined shaft of pump closest to
                                        hydrostatic pump assembly                   engine. Replace shaft if broken or if
                                                                                    splines are sheared.

                                        Sheared spline or broken shaft in pump      Remove gear pump from hydrostatic
                                                                                    pump and inspect the splined shaft and
                                                                                    coupler. Replace components as
                                                                                    needed.

                                        Restraint bar switch or seat switch not     Check switches and wiring. Replace as
                                        closing                                     needed. Check indicator light on the
                                                                                    interlock module.

                                        Solenoid lock valve(s) malfunctioning       Check electrical connections to sole-
                                                                                    noid. Replace as needed.

                                        Low or no charge                            Check charge.


PRINTED IN USA                                   50950421/A1218                                                                95

--- Page 13 ---
GEHL V420 / MUSTANG 4200V                                                  HYDRAULIC SYSTEM


     Hydraulics - High-Flow Auxiliary Lift Arm Components


             Parts Listing For Previous Drawing


1     ST MJ16-MORB12                              22   WLDMT/HOSE PIVOT
2     HLN INST 5/16 CZY                           23   BAND
3     HLN INST 1/4 CZY                            24   TUBE/HOSECARRIAGE
4     ST MJ08-MORB06                              25   TUBE/HYD -08 DRAIN
5     CS FL LOCK 3/8X3/4 C5ZY                     26   PLATE/TWIN COVER/ASSY
6     90 MJ16-FJS16                               27   WLDMT/ARM/CARRIAGE
7     BAR/HOSE PIVOT LINKAGE                      28   TUBE/HYD -16 JOY STICK
8     TIE/CABLE .50X12.90 DUAL BLACK              29   TUBE/HYD -16 JOY STICK
9     CLAMP/TUBE 1.00 TWIN                        30   HOSE/ASSY/.50 X 76.00
10    PLATE/TWIN COVER T4                         31   PLATE/CLAMP BASE
11    BLOCK/COUPLER                               32   STRIP/TRIM 20.75
12    COVER/HI FLOW COUPLER                       33   HOSE/ASSY/1.00 X 71.00
13    TUBE/HI-FLOW                                34   BUSHING/.313X.75
14    TUBE/HI-FLOW                                35   TIE/CABLE .50X19.20 DUAL
15    TUBE/FRONT HI FLO DRAIN                     36   CLAMP/TUBE SINGLE RELIEF
16    PLATE/SPACER                                37   PLATE/COVER
17    TUBE/REAR HI FLO                            38   CS FL 3/8X3-1/2 C5ZY
18    HOSE/ASSY/1.00 X 73.00                      39   CS 5/16X3-3/4 C5ZY
19    90-LL MJ16-MAORB12                          40   CS 5/16X4-1/2 C5ZY
20    VALVE/DPX160                                41   CS 1/4X3-3/4 C5ZY
21    TUBE/HYD -08 DRAIN


PRINTED IN USA                           50950421/A1218                                 105

--- Page 14 ---
GEHL V420 / MUSTANG 4200V                                                                   HYDRAULIC SYSTEM

Hydraulic Oil Filter Element Replacement                        4. Pull up on the filter element and remove it from the
                                                                   reservoir.
Gehl V4200 and Mustang 4200V model skid-steer
loaders have one hydraulic oil filter. The filter needs to
be replaced when the restriction indicator light on the
right instrument keypad comes on, indicating the return
filter is restricted or, at the regular maintenance interval.
The filter element should be replaced after every 500
hours of operation or annually (whichever occurs first).
NOTE: There is an initial 50-hour element replacement
schedule for new skid-steer loaders with original filters.
Replacement Procedure


                      WARNING                                   5. Install the new filter element in the reservoir.
BEFORE beginning this service procedure,                        6. After properly positioning the spring, reinstall the
perform the following SAFETY procedure:                            cover plate and its hardware.
• Remove attachment from lift arm.                              7. Refill the hydraulic reservoir. Refer to the Lubrica-
• Raise lift arm; engage lift arm support device.                  tion chapter in this manual for the hydraulic fluid
• Shut off the engine.                                             requirements and specifications.

• Tilt back ROPS/FOPS until lock engages.
(For detailed instructions, refer to the Safety
chapter in this manual.)                                                             WARNING
1. At the left side of the chassis, remove the left side                        NEVER use your hands to
   access cover.                                                                search for hydraulic fluid leaks.
                                                                                Use a piece of cardboard or
2. Clean any dirt/debris off the surface of the filter                          paper. Escaping fluid under
   housing.                                                                     pressure can be invisible and
3. Remove four bolts on the cover plate and remove              penetrate the skin causing serious injury. If
   the plate and spring.                                        any fluid is injected into your skin, see a doc-
                                                                tor at once. Injected fluid MUST be surgically
                                                                removed by a doctor familiar with this type of
                                                                injury or gangrene may result.


                                                                                     WARNING
                                                                              ALWAYS wear safety glasses
                                                                              when checking for hydraulic
                                                                              fluid leaks. Escaping fluid
                                                                              under pressure can be invisible
                                                                              and can cause permanent eye-
                                                                sight damage if safety glasses are not worn.

                                                                8. ALWAYS check for hydraulic fluid leaks after
                                                                   reassembling components of the hydraulic system.


PRINTED IN USA                                      50950421/A1218                                                    115

--- Page 16 ---
GEHL V420 / MUSTANG 4200V                                                           HYDRAULIC SYSTEM

2. Remove the two locknuts securing the safety lock
   valve to the valve mounting plate. Slide the safety
   lock valve off its mounting plate.                                        WARNING
                                                                           NEVER use your hands to
                                                                           search for hydraulic fluid leaks.
                                                                           Use a piece of cardboard or
                                                                           paper. Escaping fluid under

View the complete manual on HeyDownloads →