PDF Service Manual Caterpillar DP90 Lift Truck - 6 MB

This collection of service manuals provides comprehensive information for the Caterpillar DP90 Lift Truck.

It covers all aspects of maintenance, troubleshooting, and repair for this heavy-duty forklift.

Technicians will find detailed instructions and specifications to perform any service task correctly.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
Service Manual

6D16 Diesel Engine
DP80              T32B-00011-up
DP90              T32B-50001-up
DP100             3DP-00001-up
DP115             4DP-00001-up
DP135             5DP-00001-up
DP150             6DP-00011-up


For use with Chassis Service Manual.   99709-68130

--- Page 3 ---
PRECAUTIONS FOR MAINTENANCE OPERATION
                     Put alignment marks on part combinations before disassembly and
                     arrange the disassembled parts neatly. This will help avoid mismating
                     of the parts later.
                     Put the alignment marks, punch marks, etc. where performance and
                     appearance will not be affected.
                     Cover the area left open after removal of parts to keep it free from dust.

                     CAUTION
             00017
                     • Take care to avoid mixing up numerous parts, similar parts, left
                       and right, etc.
                     • Keep new parts for replacement and original (removed) parts
                       separate.


                     Apply the specified oil or grease to U-packings, oil seals, dust seals
                     and bearings during assembly.
                     Use only the specified oil, grease, etc. for lubricant, remove the excess
                     immediately after application with a piece of waste, etc.

                     CAUTION
                        When the specified lubricant, fluid and sealant is not available,
                        you may use an equivalent.
             00018


                     Wear goggles when using a grinder or welder. Pay full attention to
                     safety by wearing gloves when necessary. Watch out for sharp edges,
                     etc. that might injure your hands or fingers.


             00019


                     Before carrying out maintenance work on the electric system,
                     disconnect the negative terminals of the batteries to prevent them from
                     short-circuiting and burning-out.

                     CAUTION
                        Be sure to turn starter and lighting switches, etc. off before
                        disconnecting or connecting battery terminals, because the
                        semiconductors can be damaged.
             14184


00-6

--- Page 4 ---
TROUBLESHOOTING

                                                                      Symptoms


                                                                                                           Abnormal engine noise
                                                                                                                                       Remarks


                                                                                        Low power output
 Possible causes

Incorrect oil viscosity                                                                                                            Gr 11
Incorrect/defective fuel                                                                                                           Gr 13
Incorrect valve clearance
Defective cylinder head gasket
Worn valve/valve seat, and carbon deposits
Weakened valve spring
Worn/damaged piston ring(s)
Worn/damaged piston ring groove(s)
Incorrect injection timing                                                                                                         Gr 13
Defective injection pump                                                                                                           Gr 13
Defective cooling system                                                                                                           Gr 14
Defective injection nozzle(s)                                                                                                      Gr 13
Air trapped in fuel system                                                                                                         Gr 13
Clogged air cleaner                                                                                                                Gr 15
Clogged muffler                                                                                                                    Gr 15
Defective turbocharger                                                                                                             Gr 15
Incorrectly fitted pipe(s)/hose(s)                                                                                                 Gr 13
Injection pump, alternator, or other auxiliary device(s) defective/incorrectly fitted                                              Gr 13, 54
Loose/damaged V-belt                                                                                                               Gr 14
Incorrectly fitted crankshaft pulley
Defective air cleaner or muffler                                                                                                   Gr 15
Defective valve spring(s)
Defective rocker shaft and bracket
Incorrect lubrication of rocker shaft bracket
Incorrect backlash in timing gears
Incorrect lubrication of timing gear peripheries and idler shafts
Worn connecting rod small end bushing and piston pin
Worn/damaged crankshaft pin and connecting rod big end bearing
Worn/damaged crankshaft journal and main bearing
Excessive end play in crankshaft and camshaft
Worn tappet(s) and camshaft

11-6

--- Page 5 ---
CYLINDER HEAD AND VALVE MECHANISM

   Tightening torques                                                                        Unit: N·m (kgf·m) [lbf·ft]
 Location            Parts to be tightened                    Tightening torque                       Remarks
    14      Glow plug                                 15 to 20 (1.5 to 2.0) [11.1 to 14.8]                 –
    19      Exhaust manifold mounting stud                       29 (3) [21.4]                             –


   Lubricant
 Location                Points of application                     Specified lubricant                   Quantity
    1       Rocker contact surface on valve cap top        Engine oil                                   As required
    6       Lip of valve stem seal                         Engine oil                                   As required
   7, 8     Valve stem                                     Engine oil                                   As required


   Special tools                                                                                       Unit: mm (in.)
 Location                    Tool name and shape                  Part No.                    Application


                                                               A: MH061668
            A: Valve Lifter                                       [with φ42
                                                                                 Removing and installing valve
    2       B: Valve Lifter                                       (φ1.65)
                                                                                 cotters
               Hook                                               valve lifter
                                                                  seat]
                                                               B: MH061679
                                                      01956


            Valve Stem
    6                                                          MH061293          Installing valve stem seals
            Seal Installer


                                                      01957


                                                               30091-07500
   7, 8     Valve Lapper                                                        Lapping valves and valve seats
                                                               (inlet, exhaust)


                                                      01958


11-22

--- Page 6 ---
PISTONS, CONNECTING RODS, AND CYLINDER LINERS
Piston and Connecting Rod Assembly
                                                                  ● Disassembly sequence
                                                                    1 Snap ring
                                                                    2 Piston pin
                                                                    3 Connecting rod bushing
                                                                    4 Connecting rod
                                                                    5 1st compression ring
                                                                    6 2nd compression ring
                                                                    7 Oil ring
                                                                    8 Piston

                                                                  ● Assembly sequence
                                                                  Reverse the order of disassembly.


                                                         02012


Service standards                                                                                 Unit: mm (in.)
 Location                 Maintenance item                  Standard value            Limit           Remedy
    2, 3    Piston pin-to-connecting rod      6D16          [38] 0.02 to 0.05          0.1            Replace
            small end bushing clearance                  (0.000787 to 0.00197)      (0.00394)
                                              6D16-TLE      [42] 0.02 to 0.05
                                                         (0.000787 to 0.00197)
    2, 8    Piston pin-to-piston clearance    6D16          [38] 0.004 to 0.02         0.05           Replace
                                                         (0.000157 to 0.000787)     (0.00197)
                                              6D16-TLE      [42] 0.004 to 0.02
                                                         (0.000157 to 0.000787)
     4      Connecting rod bend and torsion                        –                   0.05           Correct or
                                                                                    (0.00197)          replace
   5 to 7   Piston ring      1st compression 6D16             0.35 to 0.55             1.5            Replace
            end gap          ring                          (0.0138 to 0.0217)       (0.0591)
                                              6D16-TLE        0.35 to 0.55
                                                           (0.0138 to 0.0217)
                             2nd compression 6D16             0.35 to 0.55             1.5            Replace
                             ring                          (0.0138 to 0.0217)       (0.0591)
                                              6D16-TLE         0.45 to 0.6
                                                           (0.0177 to 0.0236)
                             Oil ring                         0.35 to 0.55             1.5            Replace
                                                           (0.0138 to 0.0217)       (0.0591)
   5 to 8   Piston ring-   1st compression 6D16               0.11 to 0.15             0.2            Replace
            to-piston ring ring                           (0.00433 to 0.00591)      (0.00787)
            groove                         6D16-TLE           0.13 to 0.18
            clearance                                     (0.0512 to 0.00709)
                             2nd compression 6D16             0.05 to 0.08             0.15           Replace
                             ring                         (0.00197 to 0.00315)      (0.00591)
                                              6D16-TLE        0.07 to 0.10
                                                          (0.00276 to 0.00394)
                             Oil ring                         0.03 to 0.06             0.15           Replace
                                                          (0.00118 to 0.00236)      (0.00591)

11-38

--- Page 7 ---
TIMING GEARS

   Special tools                                                                                     Unit: mm (in.)
Location                        Tool name and shape                        Part No.             Application


                                                                                         Removing No. 1 idler
   2, 4    Gear Puller                                                   MH061326
                                                                                         shaft and gear


                                                                02065

           Idler Gear Bushing Puller

                                A      B                                 <No. 1>
                                                                         MH062601        Removing and fitting
  3, 11    No. 1 idler    φ37     φ40
                                                                         <No. 2>         idler gear bushings
           gear bushing (φ1.46) (φ1.57)
                                                                         MH061779
           No. 2 idler    φ32     φ35
           gear bushing (φ1.26) (φ1.38)                         02066


                                                                                         Removing No. 2 idler
   13      Idler Shaft Puller                                            MH062405
                                                                                         gear shaft


                                                                02067


                                            ◆ Service procedure
                                            ● Pre-disassembly inspection
                                            (1) Gear backlash
                                            For each gear pair, measure backlash at three or more points. If any
                                            measurement exceeds the specified limit, replace the defective part(s).


                                    02284


                                            (2) Idler gear end play
                                            If the measurement exceeds the specified value, replace the defective
                                            part(s).


                                    02069


11-54

--- Page 8 ---
CRANKSHAFT AND CRANKCASE
                     [Inspection]

                     CAUTION
                     • Do not attempt to manually expand either bearing 9, 17 if its
                       span is insufficient.
                     • Upper and lower bearings 9, 17 must be replaced as a set.


                     (1) Span when free
             01995   If either bearing's span when free exceeds the specified limit, the
                     bearings 9, 17 must be replaced.

                     (2) Main bearing-to-crankshaft clearance
                      • Fit the upper main bearing 17 into the crankcase 18 and the lower
                         main bearing 9 into the main bearing cap 10. Then, tighten the bolts
                         8 to their specified torque.
                      • Measure the internal diameters of the main bearings 9, 17 and the
                         outside diameter A of the crankshaft journal. If the clearance
                         exceeds the specified limit, replace the defective part(s).


             02104


                      10 Main bearing caps
                     [Removal]


             02100
                     [Installation]
                      • Starting at the front of the engine B, fit the main bearing caps 10 in
                         the order of the numbers A embossed on them and such that the
                         numbers are in the positions illustrated.
                      • The bolts 8 can be reused only three times. Before fitting the bolts,
                         make a punch mark on the head of each bolt to indicate times of
                         reuse.

                     CAUTION
                        If any bolt already has three punch marks, it must not be
             02103      reused any more; replace it with a new one.

11-70

--- Page 9 ---
12

<A type>             [Removal]

                         : Oil Filter Wrench


           P 47030
<B type>


           P 47031
<C type>


           P 11109


                                               12-13

--- Page 12 ---
13

CAUTION
• Fuel is highly flammable; keep it away from flames and sources of heat.
• To minimize the risk of fire, wipe up any spilled fuel.
• For maintenance of the injection pump assembly 23, please contact a Bosch Automotive Systems service
  station or Denso service station.
• Dirt particles in the injection pump assembly 23 can seriously detract from engine performance. To
  prevent the ingress of dirt, cover all pipes, hoses, and other parts after removal.
• Never carry around the injection pump assembly 23 by holding it at the lever or the engine speed sensor
  *b. Removing the lever may result in deteriorated pump performance.
• Do not remove the injection pump bracket 25 unless it is faulty.


                                                                                                     13-29

--- Page 13 ---
13

        • Remove carbon from the injection orifice of the nozzle 12 using the
          Needle Cleaner of the         Cleaning Tool Set. Insert the Needle
          Cleaner and rotate it to dislodge the carbon.


01893


        • Clean the seat of the nozzle 12 using the Cleaning Scraper of the
             Cleaning Tool Set.
        • To remove burned and hardened carbon, use FUSO Carbon
          Remover.


01894


        [Inspection]
         • Wash the needle valve 13 and nozzle 12 in gas oil, then fit them
            together.
         • Pull up the needle valve 13 by approximately 1/3 of its entire stroke,
            then check that it drops under its own weight. Repeat this test
            several times, turning the needle valve each time.
         • If the needle valve 13 does not drop as required, wash it in gas oil
            and carry out this test again. If the needle valve is still defective,
            replace the needle valve and nozzle 12 as a set.
01911
        NOTE
           Whenever a nozzle 12 is replaced, the nozzle and needle valve 13
           must be replaced as a set using Nozzle Service Kit. (This applies
           to BOSCH AUTOMOTIVE SYSTEMS products only.)


                                                                           13-45

--- Page 14 ---
WATER PUMP
                       [Installation]
                       CAUTION
                       • Before refitting impeller 3, check the number of punch marks in
                         location A shown in the illustration. If there is no or only one
                         punch mark in location A, the impeller can be refitted. Ensure to
                         punch a mark in location A for future reference before refitting
                         the impeller.
                       • The punch mark is used to show how many times in the past
             P 46285     impeller 3 is removed and refit. If there are two punch marks (i.e.
                         removed and refit twice in the past), do not refit the impeller
                         again. Replace it with a new impeller.


                       [Press-fitting]
                       Press-fit impeller 3 until its end face B is in line with end face A of water
                       pump shaft 10.

                          C: Press

                       NOTE
                         Press-fit the impeller such that flange side D of water pump shaft
                         10 is the load receiving surface.
              16930


                         3 10 Impeller-to-water pump shaft interference
                       If the measurement does not conform with the standard value, replace
                       the defective part(s).

                       CAUTION
                          Even if the standard value is satisfied, reassembly must not be
                          carried out more than twice.


              16931


                        4 Flange
                       [Removal]

                          A: Gear puller


              16932


14-16

--- Page 15 ---
15

        ● Cleaning after disassembly
        • Before cleaning, visually check the individual parts for burns, rubbed
          stains, etc. which might disappear after cleaning. If there is
          anything wrong, replace.

        CAUTION
           Do not immerse the actuator assembly 6 in the solvent. Clean
           it with a cloth dipped in kerosene.


        • Immerse the disassembled parts in a non-combustible solvent
          (DAIDO CHEMICAL INDUSTRY CO., LTD. DAI CLEANER T-30).


13628


        • Take out the parts from the solvent and blow compressed air A
          against them.


18293


        • Scrape off deposits.

           B: Plastic scraper or stiff brush

        • Re-immerse in the solvent.
        • Blow compressed air A.


13630


        ● Inspection after reassembly
        (1) Manually rotate the compressor wheel 22 and turbine wheel 23 to
            check whether they rotate smoothly.


18358

                                                                          15-13

--- Page 16 ---
SPECIFICATIONS
                          Item                                             Specifications
 Alternator      Manufacturer                                     MITSUBISHI ELECTRIC CORP.
                 Type                               Alternator with built-in regulator, fan externally mounted type
                                                                              Brushless
                 Vacuum pump                                 Provided                          Not provided
                 Model                                      A4TU 3186                  A4T4 0286        A4T4 0386
                 Output                       V–A             24–40                                24–50
 Starter         Manufacturer                                     MITSUBISHI ELECTRIC CORP.
                 Model                                                       M8T60071
                 Output               V–kW (HP)                               24–5 (6.7)
                 Magnet switch operating                                      16 or less
                 voltage                       V
 Starter relay   Model                                     U001T35383                           U1X15076
                 Exciting current             V–A                              24–2.3
                 Closed magnetic voltage       V                              16 or less
                 Opened magnetic voltage       V                               4 or less
                 Allowable breaking voltage    V                                 200
 Intake air      Manufacturer                                              Hiyoshi Denso
 heater
                 Voltage – capacity        V–kW                                22–2.9
                 Fuse capacity                 A                                 127
 Heater relay    Manufacturer                                     MITSUBISHI ELECTRIC CORP.
                 Model                                                        U1T31383
                 Voltage – current            V–A                              24–2.3
                 Fuse capacity                 A                                 127
 Glow plug       Type                                                      Sheathed type
                 Voltage – current            V–A                               23–3
 Glow relay      Model                                                        U1T06670
                 Voltage – current            V–A                              24–2.3
                 Fuse capacity                 A                                 127


54-2

--- Page 17 ---
ON-VEHICLE INSPECTION AND ADJUSTMENT
1. Inspection of Preheater System <Glow Plug Specification>
                                                • Set the starter switch to OFF.
                                                • Connect the inspection lamp 2 (24V–1.8W or thereabouts) to the
                                                  glow plug 1.
                                                • Set the starter switch to the HEAT position.
                                                • If the inspection lamp 2 does not come on, check the glow plug or
                                                  heater relay.


                                   08718


2. Inspection of Safety Relay
Service standards
 Location                    Maintenance item                Standard value      Limit            Remedy
    6       Output voltage     When engine is stationary        1V or less        –      Replace alternator or
            at terminal P                                                                wiring.
                               While engine is running          12 – 16V          –      Check and replace
                               (at idle, 600 rpm or more)                                wiring.
            Output voltage     When engine is running          Approx. 24V        –      Check and replace
            at terminal R                                                                wiring.
            Output voltage     When engine is started           1V or less        –      • If the output voltage is
            at terminal S      (in cranking state)                                         close to the battery
                                                                                           voltage, replace the
                                                                                           safety relay.
                                                                                         • If the output voltage is
                                                                                           0V, check and replace
                                                                                           parts.
            Output voltage     When engine is running           5V or less        –      • Replace.
            at terminal L                                      (but not 0V)              • If the output voltage is
                                                                                           close to the battery
                                                                                           voltage, inspect the
                                                                                           alternator and herness
                                                                                           and replace if necessary.


54-18

--- Page 18 ---
ALTERNATOR <24V–40A (without vacuum pump)>
Alternator Assembly

 <Triple pulley>


 <Double pulley>


                                                                                                             16754

● Disassembly sequence
  1 Rotor & front bracket assembly                            11    Front bracket
  2 Nut                                                       12    Stator & rear bracket assembly
  3 Pulley                                                    13    Stator assembly
  4 Fan                                                       14    Field coil
  5 Spacer                                                    15    Regulator
  6 Rear bearing                                              16    Rectifier
  7 Rotor assembly                                            17    Rear bracket
  8 Cover
  9 Front bearing                                                  : Non-reusable part
 10 Oil seal


NOTE
  Do not remove parts 6, 9 and 13 unless they are found to be defective.

● Reassembly sequence

 12     1          12:   17   16                         1:        11   10    9    8
                                     14   13                                             5   4       3   2
                              15                                              7    6


54-34

--- Page 19 ---
STARTER <24V–5kW>
                       • Immediately (in less than 5 seconds) after the pinion 3 has started
                         rotating, set the switch C to OFF to stop rotation of the pinion.

                       CAUTION
                          When the switch A and switch C are set to ON, current is
                          supplied to both the pull-in coil P and holding coil H. Since
                          wiring is such that no voltage is applied to terminal B of the
                          starter, current flows to the pull-in coil during rotation of the
             P 14260      pinion 3.
                          To prevent baking the pull-in coil, therefore, it is necessary that
                          the switch C is set to OFF immediately (in less than 5 seconds)
                          after the pinion has started rotating.


                       • Set the pipe-like tool E on the pinion stopper 2.
                       • Lightly strike the tool E with a hammer to remove the stopper ring 1
                         from the ring groove F of the pinion stopper 2.
                       • Remove the stopper ring 1 and remove the pinion 3.
                       • Set the switch A to OFF to stop supplying current to the starter.
             P 10779
                       CAUTION
                          When the power supply to the starter is stopped, the pinion 3
                          may move in and the stopper ring 1 may fit in the ring groove F of
                          the pinion stopper 2 again.
                          In this case, repeat the operations by supplying current to the
                          starter.


                       [Installation]
                       To install the pinion 3, it is not necessary to supply current to the
                       starter.
                        • Install the pinion stopper 2 and pinion 3 on the overrunning clutch
                           32 in the direction shown.
                        • Set the stopper ring 1 in the ring groove F of the overrunning clutch
                           32.


             P 10781


                       • Pull the pinion 3 strongly to make sure that the stopper ring 1
                         securely fits in the ring groove F of the pinion stopper 2.


             P 10782


54-50

--- Page 21 ---
AIR PRESSURE GOVERNOR                                                                                          61

                                            ● Disassembly sequence
                                              1 Cover
                                              2 Nut
                                              3 Adjusting screw
                                              4 Spring
                                              5 Nut
                                              6 Sleeve
                                              7 O-ring
                                              8 Snap ring
                                              9 Filter
                                             10 Screen
                                             11 Cap
                                             12 Diaphragm

                                                 : Non-reusable parts

                                            ● Reassembly sequence
                                            Reverse the order of disassembly.

                                            ● Adjustment after reassembly
                                               P.61-8


                                18426


  Tightening torque                                                                          Unit: N·m (kgf·m) [lbf·ft]

Location                Parts to be tightened                           Tightening torque                 Remarks
   2       Nut (for tightening of adjusting screw)               9.8 to 15 (1 to 1.5) [7.2 to 11.1]            –
   5       Nut (for tightening of sleeve)                       15 to 20 (1.5 to 2) [11.1 to 14.8]             –


                                                                                                                   61-23

--- Page 50 ---
7. Seat frame

(1) A seat frame with insulator is used to impede transmission of engine and transmission noise and dampen engine
    vibration before being transmitted to the cab. The seat frame also serves as a cab mount.
(2) The standard version does not use the seat frame or any other similar structure.
(3) The seat frame is installed via four mounts (b) onto the truck frame using four bolts (a). To the seat frame, the
    steering column, parking brake lever, heater and other components are attached. The seat frame can be removed
    by removing the bolts (a) while supporting it with a hoist.


                                                                                                             208995


                                                         –8–

View the complete manual on HeyDownloads →