PDF Service Manual Bobcat S150 Skid Steer Loader - 4 MB

This is the official service manual for the Bobcat S150 Skid Steer Loader, specifically for serial numbers A8M0 60001 and above.

This comprehensive guide provides step-by-step instructions for all repair and maintenance procedures.

From the hydraulic system to the engine, this manual gives you the information needed to perform diagnostics and repairs like a professional technician.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
Service Manual
                     S150 Skid-Steer Loader
                              S/N A8M0 60001 & Above


          EQUIPPED WITH
        BOBCAT INTERLOCK
      CONTROL SYSTEM (BICS)


6987054-EN (10-08)                  Printed in Europe.   © Bobcat Company 2008

--- Page 3 ---
SAFETY INSTRUCTIONS                                            The following publications provide information on the safe
                                                               use and maintenance of the Bobcat machine and
                                                               attachments:
                  Safety Alert Symbol
                                                               •   The Delivery Report is used to assure that complete
  This symbol with a warning statement means:                      instructions have been given to the new owner and
  “Warning, be alert! Your safety is involved!”                    that the machine is in safe operating condition.
  Carefully read the message that follows.
                                                               •   The Operation & Maintenance Manual delivered with
                                                                   the machine or attachment contains operating
                                                                   information as well as routine maintenance and
                                                                   service procedures. It is a part of the machine and can
                  WARNING                                          be stored in a container provided on the machine.
                                                                   Replacement Operation & Maintenance Manuals can
                                                                   be ordered from your Bobcat dealer.
Instructions are necessary before operating or
servicing machine. Read and understand the                     •   Machine signs (decals) instruct on the safe operation
Operation & Maintenance Manual, Operator’s                         and care of your Bobcat machine or attachment. The
Handbook and signs (decals) on machine. Follow                     signs and their locations are shown in the Operation &
warnings and instructions in the manuals when                      Maintenance Manual. Replacement signs are
making repairs, adjustments or servicing. Check for                available from your Bobcat dealer.
correct function after adjustments, repairs or service.
Untrained operators and failure to follow instructions         •   An Operator’s Handbook fastened to the operator cab.
can cause injury or death.                                         It’s brief instructions are convenient to the operator.
                                            W-2003-0903            The handbook is available from your dealer in an
                                                                   English edition or one of many other languages. See
                                                                   your Bobcat dealer for more information on translated
                                                                   versions.
                  WARNING                                      •   The AEM Safety Manual delivered with the machine
                                                                   gives general safety information.
Warnings on the machine and in the manuals are for
your safety. Failure to obey warnings can cause injury         •   The Service Manual and Parts Manual are available
or death.                                                          from your dealer for use by mechanics to do shop-type
                                            W-2044-1285            service and repair work.

                                                               •   The Skid-Steer Loader Operator Training Course is
                                                                   available through your local dealer or at
           IMPORTANT                                               www.training.bobcat.com or www.bobcat.com.
                                                                   This course is intended to provide rules and practices
                                                                   of correct operation of the Skid-Steer Loader. The
This notice identifies procedures which must be
                                                                   course is available in English and Spanish versions.
followed to avoid damage to the machine.
                                             I-2019-0284
                                                               •   Service Safety Training Courses are available from
                                                                   your Bobcat dealer or at www.training.bobcat.com
                                                                   or www.bobcat.com. They provide information for
                                                                   safe and correct service procedures.

                                                               •   The Skid-Steer Loader Safety Video is available from
                                                                   your Bobcat dealer or at www.training.bobcat.com
                                                                   or www.bobcat.com.


                                                                                                          SI SSL-1007 SM


                                                           v                                         S150 Service Manual

--- Page 4 ---
SAFETY AND MAINTENANCE (CONT’D)

TRANSPORTING THE LOADER ON A TRAILER . . . . . . . . . . . . . 10-40-1
  Fastening. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-40-1
  Loading And Unloading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-40-1


TIGHTEN ALL HARDWARE PER SIZE TO GRADE 5 TORQUE (SEE STANDARD TORQUE SPECIFICATIONS FOR
BOLTS, SPEC SECTION ) UNLESS OTHERWISE SPECIFIED.


                                                                 10-3                                    S150 Service Manual

--- Page 5 ---
TRANSPORTING THE LOADER ON A TRAILER                           Fastening

Loading And Unloading                                          Figure 10-40-2


                       WARNING
        AVOID SERIOUS INJURY OR DEATH
Adequately designed ramps of sufficient strength are
needed to support the weight of the machine when
loading onto a transport vehicle. Wood ramps can
break and cause personal injury.
                                               W-2058-0807                          N-19048A                              P-73276


Be sure the transport and towing vehicles are of adequate
size and capacity for weight of loader [See “Performance”
on page SPEC-10-2].

Figure 10-40-1


                                                                                   Alternate Front Tie Down


                                                                                                                       P-31829B


                                                               Use the following procedure to fasten the Bobcat Loader
                 1
                                                               to the transport vehicle to prevent the loader from moving
                                                               during sudden stops or when going up or down slopes
                                                               [Figure 10-40-2].
             P-43631                           P-45215C

                                                               •    Lower the bucket or attachment to the floor.
A loader with an empty bucket or no attachment must be         •    Stop the engine.
loaded backward onto the transport vehicle [Figure 10-         •    Engage the parking brake.
40-1].                                                         •    Install chains at the front and rear loader tie down
                                                                    positions [Figure 10-40-2]
The rear of the trailer must be blocked or supported (Item     •    Fasten each end of the chain to the transport vehicle.
1) [Figure 10-40-1] when loading or unloading the loader
to prevent the front end of the trailer from raising up.


                                                          10-40-1                                             S150 Service Manual

--- Page 6 ---
REMOTE START TOOL (SERVICE TOOL) KIT -
6689779

Description

The Remote Start Tool (Service Tool) Kit is a replacement
tool for MEL 1563 Remote Start Tool and MEL 1400B -
BOSS® Diagnostic Tool.

The Remote Start Tool (Service Tool) Kit, P/N 6689779,
can be used to service older loaders with the BOSS®
system using the supplied BOSS® Service Tool Harness
P/N 6689745.

The Remote Start Tool (Service Tool) Kit, P/N 6689779,
can be used to service newer loaders using the supplied
harness P/N 6689747.

A computer can be connected to the Remote Start Tool
(Service Tool) for diagnostics and software updates using
the computer harness P/N 6689746 in conjunction with
the loader harness.


                                                       10-61-1   S150 Service Manual

--- Page 7 ---
AIR CLEANER SERVICE                                               Outer Filter

Replacing Filter Elements                                         Figure 10-80-3

Figure 10-80-1

              1
                                          1


                                                                                 1


                                                                                                                     P-31836
                    B-15552G                      B-15553G

                                                                  Remove the wing nut and remove the dust cover (Item 1)
It is important to change the air filter element only when        [Figure 10-80-3].
the Air Cleaner Icon in the right panel is ON (Item 1)
[Figure 10-80-1] and you hear three beeps from the                Figure 10-80-4
alarm.

Replace the inner filter every third time the outer filter is
                                                                             1
replaced or as indicated.

Figure 10-80-2


                                                    2

                                                                                                                     P-31837
      1


                                                                  Remove the wing nut and pull the outer filter element
                                                                  (Item 1) [Figure 10-80-4] out and discard.

                                                                  NOTE: Make sure all sealing surfaces are free of dirt
                                                   B-15551
                                                                        and debris.

Press and hold the LIGHT Button (Item 1) [Figure 10-80-           Install new filter. Push all the way in until it contacts the
2] for two seconds.                                               base of the housing. Install wing nut.

If the filter element needs replacement, the CODE [01-17]         Install the dust cover and the wing nut [Figure 10-80-3].
(Air Filter Plugged) will show in the HOURMETER / CODE
DISPLAY (Item 2) [Figure 10-80-2].                                Check the air intake hose and the air cleaner housing for
                                                                  damage. Make sure all connections are tight.


                                                             10-80-1                                     S150 Service Manual

--- Page 8 ---
HYDRAULIC / HYDROSTATIC SYSTEM                                    Hydraulic / Hydrostatic Fluid Chart

Checking And Adding Fluid                                         Figure 10-120-2

Use only recommended fluid in the hydraulic system [See
“HYDRAULIC/HYDROSTATIC FLUID SPECIFICATIONS”
on page SPEC-40-1].

Put the loader on a level surface.

Lower the lift arms and tilt the Bob-Tach fully back.

Stop the engine.

Figure 10-120-1


                                                                                                                 P-64023A


                 1
                                                                  Use the correct hydraulic / hydrostatic fluid shown in
                        1                                         hydraulic / hydrostatic fluid chart [Figure 10-120-2].
                                                     2


                     P-45224A
                      P-45224C                     P-48011


Check the fluid level in the sight gauge (Item 1) [Figure 10-
120-1].

Open the rear door and raise the rear grill. Remove the fill
cap (Item 2) [Figure 10-120-1].

Add fluid as needed to bring the level to the center of the
sight gauge (Item 1) [Figure 10-120-1].

Install the fill cap (Item 2) [Figure 10-120-1].

Lower the rear grill and close the rear door.


                                                             10-120-1                                   S150 Service Manual

--- Page 9 ---
BOB-TACH (POWER)                                           Figure 10-141-2

This machine may be equipped with a Power Bob-Tach.
                                                                                           1
Inspection And Maintenance

Figure 10-141-1                                                                             2


                                                                                         Wedge    must     contact
                                                                                         lower edge of hole in the
                                                                                         attachment.

                                                                               N-17022                    B-15177


                                                           The wedges must extend through the holes in the
                                                           attachment mounting frame (Item 1) [Figure 10-141-2].
                                           B-15993N

                                            B-15891        The spring loaded wedge (Item 1) must contact the lower
                                                           edge of the hole in the attachment (Item 2) [Figure 10-
                                                           141-2].
Push and hold the BOB-TACH "WEDGES UP" switch until
wedges are fully raised. Push and hold the BOB-TACH        If the wedge does not contact the lower edge of the hole
"WEDGES DOWN" switch [Figure 10-141-1] until the           [Figure 10-141-2], the attachment will be loose and can
wedges are fully down.                                     come off the Bob-Tach.

The levers and wedges must move freely.                    Figure 10-141-3


                   WARNING
Bob-Tach wedges must extend through the holes in
attachment. Lever(s) must be fully down and locked.
Failure to secure wedges can allow attachment to
come off and cause injury or death.
                                           W-2102-0497


                                                                                                          B-17460


                                                           Inspect the mounting frame on the attachment and the
                                                           Bob-Tach, linkages and wedges for excessive wear or
                                                           damage [Figure 10-141-3]. Replace any parts that are
                                                           damaged, bent, or missing. Keep all fasteners tight.

                                                           Look for cracked welds. Contact your Bobcat dealer for
                                                           repair or replacement parts.

                                                           Lubricate the wedges [See “SERVICE SCHEDULE” on
                                                           page 10-70-1] and [See “LUBRICATING THE LOADER”
                                                           on page 10-150-1].


                                                      10-141-1                                  S150 Service Manual

--- Page 10 ---
LOADER STORAGE AND RETURN TO SERVICE                               Return to Service

Storage                                                            After the Bobcat Loader has been in storage, it is
                                                                   necessary to follow a list of items to return the loader to
Sometimes it may be necessary to store your Bobcat                 service.
Loader for an extend period of time. Below is a list of
items to perform before storage.                                   •     Check the engine and hydraulic oil levels; check
                                                                         coolant level.
•   Thoroughly clean the loader including the engine
                                                                   •     Install a fully charged battery.
    compartment.
                                                                   •     Remove grease from exposed cylinder rods.
•   Lubricate the loader.
                                                                   •     Check all belt tensions.
•   Replace worn or damaged parts.
                                                                   •     Be sure all shields and guards are in place.
•   Park the loader in a dry protected shelter.
                                                                   •     Lubricate the loader.
•   Lower the lift arms all the way and put the bucket flat
    on the ground.                                                 •     Check tire inflation and remove blocks from under
                                                                         frame.
•   Put blocks under the frame to remove weight from the           •     Remove cover from exhaust pipe opening.
    tires.
                                                                   •     Start the engine and let run for a few minutes while
•   Put grease on any exposed cylinder rods.                             observing the instrument panels and systems for
                                                                         correct operation.
•   Put fuel stabilizer in the fuel tank and run the engine a
                                                                   •     Operate machine, check for correct function.
    few minutes to circulate the stabilizer to the pump and
    fuel injectors.                                                •     Stop the engine and check for leaks. Repair as
                                                                         needed.
    If biodiesel blend fuel has been used, perform the
    following:

    Drain the fuel tank, refill with 100% petroleum diesel
    fuel, add fuel stabilizer and run the engine for at least
    30 minutes.

•   Drain and flush the cooling system. Refill with
    premixed coolant.

•   Replace all fluids and filters (engine, hyd. / hydro.).
•   Replace air cleaner and heater filters.
•   Put all controls in neutral position.
•   Remove the battery. Be sure the electrolyte level is
    correct then charge the battery. Store it in a cool dry
    place above freezing temperatures and charge it
    periodically during storage.
•   Cover the exhaust pipe opening.
•   Tag the machine to indicate that it is in storage
    condition.


                                                              10-190-1                                      S150 Service Manual

--- Page 11 ---
HYDRAULIC/HYDROSTATIC SCHEMATIC
                             WITH 2 SPEED OPTION
                      S150 (S/N A8MO60001 AND ABOVE)


                              (PRINTED NOVEMBER 2008)
                                      V-1111legend


Printed in Europe                                       V-1111legend (11-1-08)

--- Page 12 ---
HYDRAULIC SYSTEM INFORMATION (CONT'D)

Troubleshooting                                                                     WARNING
The following troubleshooting chart is provided for
assistance in locating and correcting problems which are        Check for correct function after adjustments, repairs
most common. Many of the recommended procedures                 or service. Failure to make correct repairs or
must be done by authorized Bobcat Service Personnel             adjustments can cause injury or death.
only.                                                                                                           W-2004-1285


                                PROBLEM                                                           CAUSE
The hydraulic system will not operate.                                         1, 2, 3, 5, 8
The transmission warning light come ON when hydraulics are operating.          1, 3
Slow hydraulic system action.                                                  1, 3, 4, 6, 8
Hydraulic action is not smooth.                                                1, 4, 5, 6, 7
Lift arms go up slowly at full engine RPM                                      1, 3, 4, 5, 6, 7, 8, 9
The lift arms or Bob-Tach will move when the pedal is in neutral position      4
The lift arms come down with the pedal is in neutral position                  4, 9, 10, 11
Bypass valve stuck                                                             12
Bypass valve stem bent or broke                                                13

                                               KEY TO CORRECT CAUSE


                    1. The fluid level is not correct.
                    2. The pedal linkage is disconnected.
                    3. The hydraulic pump has damage.
                    4. The pedal linkage is not adjusted correctly.
                    5. Relief valve is not at the correct pressure.
                    6. Suction leak on the inlet side of the hydraulic pump.
                    7. Fluid is cold. Wrong viscosity fluid [See “HYDRAULIC/HYDROSTATIC FLUID
                   SPECIFICATIONS” on page SPEC-40-1].
                    8. Using the loader for more than its rated capacity.
                    9. Internal leak in the lift cylinder(s).
                   10. External leak from the cylinder(s).
                   11. Damaged lift spool.
                   12. Rotate shaft.
                   13. Replace manual spool cartridge.


                                                           20-10-5                                      S150 Service Manual

--- Page 13 ---
CYLINDER (TILT) (CONT'D)                                    Base End Pivot Pin Removal and Installation

Removal And Installation (Cont’d)                           Figure 20-21-7

Figure 20-21-6


                                                                                                      1


                       1


                             2
                                                                                                             P-68534


                                             P-34228
                                                            Remove the tilt cylinder from the Bob-Tach [See “Removal
                                                            And Installation” on page 20-21-2].
Disconnect the hose (Item 1) [Figure 20-21-6] from the
cylinder.                                                   Loosen the retainer bolt (Item 1) [Figure 20-21-7] from
                                                            the tilt cylinder rod base end pin.
Remove the cylinder (Item 2) [Figure 20-21-6] from the
rod end pivot pin.                                          Installation: Tighten the retainer bolt to 175-190 ft.-lb.
                                                            (240-260 N•m) torque.
Remove the cylinder from the loader.
                                                            Strike the head of the bolt (Item 1) [Figure 20-21-7] to
                                                            push the pivot pin out.

                                                            Reverse the removal procedure to install the pivot pin.


                                                       20-21-3                                    S150 Service Manual

--- Page 14 ---
CYLINDER (BOB-TACH) (CONT’D)                                       Figure 20-22-11

Disassembly and Assembly (Cont’d)

Figure 20-22-9
                                                                                 1


                                                                                                                      P-48040


                                                                   Remove the wiper seal (Item 1) [Figure 20-22-11] from
                                                      P7424        the cylinder head.

                                                                   Figure 20-22-12
Assembly: Install the new seal on the tool and slowly
stretch it until it fits the piston [Figure 20-22-9]. Allow the
seal to stretch for 30 seconds before installing it on the
piston.                                                                      2

Once the seal is installed on the piston, a piston ring
compressor can be used on the piston for 3 minutes to
compress the seal into place.
                                                                         1
Figure 20-22-10


                                              1


                                                                             P-48041A                                 P-48042


                                                                   Install the wiper seal, with the wiper side of the seal (Item
                                                                   1), toward the outside of the head (Item 2) [Figure 20-22-
                             2                                     12].


                                                    P-48039


Remove the two O-rings (Item 1) and the back-up washer
(Item 2) [Figure 20-22-10] from the cylinder head.


                                                              20-22-5                                     S150 Service Manual

--- Page 15 ---
HYDRAULIC CONTROL VALVE (STANDARD)                         Figure 20-40-16
(CONT'D)

Removal And Installation (Cont'd)

Figure 20-40-14
                                                                                                           1
                                                                                1


                  1


                                                                                                               P-66974


                                                           Connect a hoist to the lifting brackets (Item 1) [Figure 20-
                                                           40-16] on the control valve.
                                            P-66962
                                                           Figure 20-40-17

Remove any tie-straps (Item 1) [Figure 20-40-14]
securing the fixed end main valve hose.
                                                                                      1
Figure 20-40-15


                                                                                                           P-66972P-
                                                                                                             P-66972
                                                                                                             P-51713
                                                                                                             34004P-
                                                                                                               51713
                  1
                                                           Remove the two mounting bolts (Item 1) [Figure 20-40-
                                                           17] fastening the control valve and bracket to the side of
                                            P-66960
                                                           the loader.

                                                           Remove the control valve from the loader.
Remove the fixed-end main valve hose (Item 1) [Figure
20-40-15] from the main control valve fitting.             Reverse removal procedure to install the hydraulic control
                                                           valve.


                                                      20-40-5                                     S150 Service Manual

--- Page 16 ---
HYDRAULIC CONTROL VALVE (STANDARD)                               Figure 20-40-51
(CONT'D)

Lift Spool And Detent Removal And Installation

The tool listed will be needed to do the following
procedure:

MEL1278 - Detent Tool
MEL1285 - Detent Spring Tool                                                                                         1

Remove the end cap/spool lock block from the control
valve.

Figure 20-40-49
                                                                                                                 P-51513


                                                                 Remove the end cap (Item 1) [Figure 20-40-51].

                                                                 Figure 20-40-52
             1


                                                 P-51511A
                                                                                               1
Remove the O-ring (Item 1) [Figure 20-40-49].                                  2

Installation: Replace the O-ring, and lubricate lightly with
oil before installation of the end cap/spool lock block.
                                                                                                                 P-51514

Figure 20-40-50
                                                                 Use a screwdriver to remove the snap ring (Item 1)
                                                                 [Figure 20-40-52].

                                                                 Remove the washer (Item 2) [Figure 20-40-52].


                  2

       1


                                                 P-51512A


Remove the spacer (Item 1) and O-ring (Item 2) [Figure
20-40-50] from the lift spool.


                                                            20-40-15                                S150 Service Manual

--- Page 17 ---
HYDRAULIC CONTROL VALVE (STANDARD)                              Figure 20-40-89
(CONT'D)

Tilt Spool Removal And Installation

Remove the lift and tilt end cap/spool lock block [See “End
Cap/Spool Lock Block Removal And Installation” on
page 20-40-14].
                                                                                                             2
Figure 20-40-87


                                                                                   1
                                                                                                                 P-68023


                                                                Remove the spool centering block (Item 1) [Figure 20-40-
         1                              2                       89] from the control valve.

                                                                Check and replace the O-ring (Item 2) [Figure 20-40-89]
                                                                before replacing the spool centering block.

                                                P-51521A        Figure 20-40-90


Remove the spacer (Item 1) and O-ring (Item 2) [Figure
20-40-87] from the tilt spool.

Figure 20-40-88


                                    1
                1                                                                                            P-51544A


                                                                Remove the tilt spool, centering spring, back-up washer
                               2
                                                                and spool seal [Figure 20-40-90].

                                                 P-68019        Installation: Always use a new spool seal.


Remove the two tubelines (Item 1) [Figure 20-40-88].

Remove the three bolts (Item 2) [Figure 20-40-88] from
the spool centering block.

Installation: Tighten the bolts to 90-100 in.-lb. (10-11,3
N•m) torque.


                                                           20-40-25                                 S150 Service Manual

--- Page 18 ---
HYDRAULIC CONTROL VALVE (ACS) OR (SJC)                           Removal And Installation

Description

Figure 20-41-1


                                                                                      WARNING
                                                                 Never work on a machine with the lift arms up unless
                                                  P-68027        the lift arms are secured by an approved lift arm
                                                                 support device. Failure to use an approved lift arm
                                                                 support device can allow the lift arms or attachment
The hydraulic control valve is located inside the main           to fall and cause injury or death.
frame on the right hand side, below the operators cab.                                                           W-2059-0598

The hydraulic control valve [Figure 20-41-1] is the
hydraulic component that uses spools to direct the flow of
hydraulic fluid to the lift, tilt and auxiliary functions.

The lift and tilt functions in the ACS or the SJC hydraulic                  IMPORTANT
control valve are operated using electronic control handle/
levers or foot pedals that send an electronic signal to the      When repairing hydrostatic and hydraulic systems,
electronic actuators to move the lift and tilt spools in the     clean the work area before disassembly and keep all
control valve.                                                   parts clean. Always use caps and plugs on hoses,
                                                                 tubelines and ports to keep dirt out. Dirt can quickly
The auxiliary function is operated by pilot pressure. There      damage the system.

View the complete manual on HeyDownloads →