PDF Service Manual 2021 Arctic Cat Wildcat XX ATV - 8 MB

This is the complete factory service manual for the 2021 Arctic Cat Wildcat XX ATV.

It contains detailed instructions for every aspect of service, repair, and maintenance.

From engine overhaul to suspension tuning, this manual provides the specifications and procedures needed by professional technicians and advanced DIY mechanics.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
2
021  SE
      RVICE
     MANUAL


           p/
            n:2262-425
                 10/20


 Wi
  ldc
    atXX

--- Page 3 ---
7. Apply new engine oil to the new oil filter seal; then
                                                                  install the new oil filter onto the engine. Tighten
                                                                  securely.
                                                               8. Install the engine drain plug and new washer.
                                                                  Tighten to 7.2 ft-lb (9.8 N-m). Install the oil tank
                                                                  drain plug and new washer. then tighten to 12 ft-lb
                                                                  (16 N-m).
                                                               9. Pour 2.70 US qt (2.55 L) of ACX All Weather syn-
                                                                  thetic oil into the oil tank. Install the dipstick. Install
                                                                  the fill plug on top of the valve cover.
                                                              10. Start the engine (while the vehicle is outside on level
                                                                  ground) and allow it to idle until at least one of the
XX231
                                                                  radiator fans cycles on and off. Check for any leak-
                                                                  ing oil. If oil is leaking, immediately stop the engine
 4. Remove the drain plug and crush washer from the               and correct the cause of the leak before proceeding.
    bottom of the oil tank. Use a funnel to direct the oil
                                                              NOTE: The manufacturer recommends the use of
    into a drain pan.
                                                              genuine lubricants.
                                                              NOTE: The oil level stick should NOT be threaded
                                                              into the oil tank for checking purposes
                                                              11. Turn the engine off and wait approximately one min-
                                                                  ute. Remove the dipstick from the oil tank and recheck
                                                                  the oil level. Add more oil if the level is not visible on
                                                                  the dipstick. The oil level MUST be within the operat-
                                                                  ing range.


                                                                   Front Differential —
                                                                Transaxle Lubricant/Fluid
XX232
                                                              To change front differential lubricant, use the following
 5. Remove the drain plug and washer from the bottom          procedure:
    of the engine and drain the oil into a drain pan.
                                                              NOTE: The fill plug is located on the front right side
NOTE: There is a “triangle” symbol cast into the oil         of the differential.
pan located next to the drain plug for identification
purposes.                                                      1. Place the vehicle on level ground; then remove the
                                                                  fill plug.


XX033A
                                                              XX116

 6. Using the oil filter wrench and a ratchet handle (or a
    socket or box-end wrench), remove the old oil filter       2. Drain the lubricant into a drain pan by removing the
    and dispose of properly. Verify the oil filter seal has       drain plug. Clean away any debris that may have
    been removed along with the filter. Do not re-use oil         accumulated onto the magnetic end of the plug.
    filter.
NOTE: Clean up any excess oil after removing the
filter.


                                                                                                                           9

--- Page 4 ---
XX084                                                        XX091


INSTALLING REAR FENDERS
 1. When installing right rear fender, install filler hose
    onto fender. Tighten hose clamp on gas tank filler
    hose.


                                                             XX092


                                                              3. Install the rear upper fender. Secure with cap screws.


XX083


 2. Install the rear lower fender. Secure with cap screws.


                                                             XX085A1


XX085B1


                                                             XX089


XX093


                                                                                                                    19

--- Page 5 ---
Troubleshooting

Problem: Handling too heavy or stiff
Condition                                    Remedy
 1. Front wheel alignment incorrect           1. Adjust alignment
 2. Lubrication inadequate                    2. Lubricate appropriate components
 3. Tire inflation pressure incorrect         3. Adjust pressure
 4. Tie rod ends seizing                      4. Replace tie rod ends
 5. Linkage connections seizing               5. Repair — replace connections
 6. EPS malfunction                           6. Troubleshoot — replace EPS
Problem: Steering oscillation
Condition                                    Remedy
 1. Tires inflated unequally                  1. Adjust pressure
 2. Wheel(s) wobbly                           2. Replace wheel(s)
 3. Wheel hub cap screw(s) loose — missing    3. Tighten — replace cap screws
 4. Wheel hub bearing worn — damaged          4. Replace bearing
 5. Tie rod ends worn — loose                 5. Replace — tighten tie rod ends
 6. Tires defective — incorrect               6. Replace tires
 7. A-arm bushings damaged                    7. Replace bushings
 8. Bolts — nuts (frame) loose                8. Tighten bolts — nuts
Problem: Steering pulling to one side
Condition                                    Remedy
 1. Tires inflated unequally                  1. Adjust pressure
 2. Front wheel alignment incorrect           2. Adjust alignment
 3. Wheel hub bearings worn — broken          3. Replace bearings
 4. Frame distorted                           4. Repair — replace frame
 5. Shock absorber defective                  5. Replace shock absorber
Problem: Steering impaired
Condition                                    Remedy
 1. Tire pressure too high                    1. Adjust pressure
 2. Steering linkage connections worn         2. Replace connections
 3. Cap screws (suspension system) loose      3. Tighten cap screws
Problem: Tire wear rapid or uneven
Condition                                    Remedy
 1. Wheel hub bearings worn — loose           1. Replace bearings
 2. Front wheel alignment incorrect           2. Adjust alignment
Problem: Steering noise
Condition                                    Remedy
 1. Caps screws — nuts loose                  1. Tighten cap screws — nuts
 2. Wheel hub bearings broken — damaged       2. Replace bearings
 3. Lubrication inadequate                    3. Lubricate appropriate components
Problem: Rear wheel oscillation
Condition                                    Remedy
 1. Rear wheel hub bearings worn — loose      1. Replace bearings
 2. Tires defective — incorrect               2. Replace tires
 3. Wheel rim distorted                       3. Replace wheel
 4. Wheel hub cap screws loose                4. Tighten cap screws
 5. Trailing arm bushings worn                5. Replace bushings or link


                                                                                    29

--- Page 6 ---
YM-205
SNO-752


 8. Thread the MAG Cover Removal Cap Screw into the       10. Using Flywheel Puller, remove the flywheel from the
    timing mark hole; then carefully pull the MAG cover       crankshaft. Account for the key in the crankshaft.
    from the crankcase. Account for two dowel pins and
    a gasket.


                                                          YM-206


YM-203


                 ! WARNING
When removing the cover be sure to keep hands away
from being pinched between the cover and the case.


                                                          YM-207


                                                          11. Thread the primary sheave bolt into the end of the
                                                              crankshaft and pull the output shaft assembly from
                                                              the engine.
                                                          12. Remove the Allen-head screws securing the water
                                                              pump assembly to the crankcase; then remove the
YM-204                                                        assembly. Account for two dowel pins and two gas-
                                                              kets.
 9. Remove the starter gear and shaft.


                                                                                                              39

--- Page 7 ---
SNO-658A                                                       SNO-293A


Measuring Piston Pin Bore Diameter                             NOTE: Be sure to install the piston rings so that the
NOTE: It may be necessary to use Piston Pin Puller
                                                               manufacturer marks (A) face up.
to remove the piston pins.                                      2. Rotate the rings until the ring end gaps are 120° from
                                                                   one another.
 1. Insert an inside dial indicator into the piston-pin
    bore. Take two measurements to ensure accuracy.
 2. Piston pin bore must be within 21.003-21.013 mm
    (0.8269-0.8273 in.).


                                                               SNO-294A


                                                                                   CAUTION
                                                               Incorrect installation of the piston rings will result in
SNO-291                                                        engine damage.
Measuring Piston Pin Diameter                                  CRANKSHAFT RUNOUT
Measure the piston pin diameter at each end and in the
center. Measurement must be within 20.990-20.995 mm             1. Support the crankshaft using a set of V Blocks; use a
(0.8264-0.8266 in.). If measurement is not within specifi-         dial indicator to read crankshaft runout.
cations, the piston pin must be replaced.                      NOTE: The contact point of the dial indicator
                                                               should be on either side of the oil port hole of the cen-
                                                               ter crankshaft journal and to the outside of the oil
                                                               port hole on the MAG and PTO end of the crank-
                                                               shaft.
                                                                2. Rotate the crankshaft slowly.
                                                                3. The reading must be 0.03 mm (0.0012 in.) or crank-
                                                                   shaft repairing/replacing will be necessary.
                                                               MEASURING CRANKSHAFT MAIN/ROD
                                                               JOURNALS (Bearing Surfaces)
                                                                1. Using a micrometer, measure each main and con-
                                                                   necting rod bearing journal from along its length and
SNO-292                                                            90° from the first measurement. Measurement must
                                                                   be within 36.976-37.000 mm (1.4557-1.4567 in.)
Installing Piston Rings                                            diameter for the crankshaft main journal and
 1. Install the piston rings according to the illustration         37.976-38.000 mm (1.4951-1.4961 in.) diameter for
    below. Stagger the end gaps of the upper and lower             connecting rod journal.
    thin oil rings until they are on directly opposite sides
    of the piston.

                                                                                                                      49

--- Page 9 ---
3. Install the Oil Pressure Test Kit with a suitable fit-
                                                                 ting; then start the engine. While the engine is run-
                                                                 ning, there should be no leaks.
                                                              4. With a radiator fan on, increase the engine speed to
                                                                 4800-4900 RPM. The oil pressure should be approx-
                                                                 imately 28-35 psi.
                                                              5. Remove the Oil Pressure Test Kit and suitable fitting
                                                                 from the engine and install cap screw with a new
                                                                 crush washer. Securely tighten the cap screw with
                                                                 washer.
                                                              6. Install the cargo tray.
XX104                                                        NOTE: If oil pressure is lower than specified, check
                                                             for an oil leak, clogged oil filter, or defective oil pump.
 6. Remove gas tank.
                                                             NOTE: If oil pressure is higher than specified, check
INSTALLING                                                   for too heavy engine oil weight (see General Informa-
 1. Place the gas tank into position; then connect the gas   tion/Foreword), clogged oil passage, or improper
    line hose, vent hose, and fuel pump.                     installation or type of oil filter.

 2. Place the three brackets into place.
 3. Install and tighten cap screws securing brackets                           Fuel Pump
    securing the gas tank.
 4. Place the battery into position and connect the bat-     NOTE: The fuel pump is only serviceable as an
    tery cables (positive cable first). Tighten the cables   assembly (see FUEL PUMP/FUEL LEVEL SENSOR
    securely.                                                in the Electrical System section).
 5. Install the battery access panel and passenger seat.

                                                                         Fuel/Vent Hoses
                   Oil Pump
                                                             Inspect the fuel lines per the maintenance schedule.
                                                             Damage from aging may not always be visible. Do not
NOTE: Whenever internal engine components wear
                                                             bend or obstruct the routing of the vent hose or fuel
excessively or break and whenever oil is contami-            return hose.
nated, the oil pump should be replaced.
TESTING OIL PUMP PRESSURE
 1. Remove the cargo tray.
                                                                  Liquid Cooling System
 2. Remove the cap screw and washer located on the
    upper portion of the engine near the #3 cylinder         NOTE: Use a good quality, biodegradable gly-
    intake (A).                                              col-based, automotive-type antifreeze. When filling
                                                             the cooling system, use the recommended cool-
                                                             ant/water mixture or one which will satisfy the coldest
                                                             anticipated weather conditions of the area in accor-
                                                             dance with the coolant manufacturer’s recommenda-
                                                             tions.

                                                                                ! WARNING
                                                             Never check the coolant level when the engine is hot or
                                                             the cooling system is under pressure.

                                                                                   CAUTION
                                                             After operating the vehicle for the initial 5-10 minutes,
                                                             stop the engine, allow the engine to cool down, and
                                                             check the coolant level. Add coolant as necessary.
XX459


NOTE: The cap screw is M8 (diameter) x 1.25
(thread pitch) x 12 mm (length), and the crush washer
is approximately 1.15 mm thick.


                                                                                                                     69

--- Page 11 ---
TROUBLESHOOTING                                               NOTE: If the meter shows no battery voltage, trou-
                                                              bleshoot the main 30-amp fuse, the battery, or the
NOTE: The EPS assembly is not serviceable and                main wiring harness.
must not be disassembled or EPS warranty will be
voided.                                                        4. Connect the red meter lead to the brown/black wire;
                                                                  then with the black lead grounded, turn the ignition
 1. Check 30-amp EPS fuse.                                        switch to the ON position. The meter must show bat-
 2. With the ignition off, disconnect the two-wire EPS            tery voltage.
    power connector on the EPS assembly and connect a          5. Connect the red meter lead to the yellow/green wire;
    volt meter set to DC voltage to the harness (black            then with the black lead grounded, depress the brake,
    meter lead to BLK and red meter lead to                       and turn the ignition switch to the START position.
    ORG/BRN).With the ignition switch in the ON posi-             The starter should engage and the meter must show
    tion, the meter should read battery voltage (if correct       battery voltage.
    voltage is not present, check connections and wiring
    harness).                                                 NOTE: When the starter is engaged, battery voltage
                                                              will be approximately 10.5 DC volts.
                     CAUTION
Do not attempt to check resistance of the EPS motor. There
are internal capacitors holding a charge that can cause
                                                                             Ignition Coils
internal damage to an ohmmeter.
 3. With ignition switch off, disconnect the three-wire       The ignition coils (A) are attached to the valve cover with
    connector on the EPS assembly and connect a volt          two fasteners per ignition coil.
    meter set to DC voltage to the harness (red meter
    lead to the ORG wire and black meter lead to battery
    ground.) With the ignition switch in the on position,
    the meter should read battery voltage (if correct volt-
    age is not present, check for loose fittings or connec-
    tions in the wiring harness).

                     CAUTION
If the CATT II has confirmed an active DTC relating to
the CAN communication wires, use extreme caution
when testing the wires. Do not probe the ECM connec-
tor with meter leads; instead use a small T-pin or other
suitable testing component to make light and proper
contact.
                                                              WT405

                     CAUTION                                  RESISTANCE
Never disconnect the ECM connector with the battery
cables installed onto the battery.                                                 CAUTION
                                                              Always disconnect the battery when performing resis-
NOTE: If after completing the preceding tests and            tance tests to avoid damaging the multimeter.
possible solutions with normal results an EPS issue
persists with active DTCs confirmed by the CATT II,           NOTE: The following test should be made using
                                                              MaxiClips and the Fluke Model 77 Multimeter set to
the EPS assembly must be replaced (see Steer-
                                                              OHMS scale.
ing/Body/Controls).
                                                               1. Disconnect an ignition coil connector.
                                                               2. Connect the red tester lead to one coil terminal; then
            Ignition Switch                                       connect the black tester lead to the other coil termi-
                                                                  nal. Primary coil resistance must be 1.19-1.61 ohms.

The ignition switch, dash switches, front accessory con-
nectors, and front switched accessory connector can be
accessed from under the dash.
VOLTAGE
NOTE: Perform this test on the harness connector.
 1. Set the meter selector to the DC Voltage position.
 2. Connect the red meter lead to the red wire; then con-
    nect the black meter lead to battery ground.
 3. Meter must show battery voltage.


                                                                                                                      79

--- Page 12 ---
4. Mark the fuel pump mounting and gas tank for
                                                                   installing purposes; then remove the cap screws
                                                                   securing the fuel pump to the gas tank and remove
                                                                   the fuel pump.

                                                                                    CAUTION
                                                               Take care not to damage the float or float arm or
                                                               replacement of the entire assembly will be necessary.


XX342

 3. Reconnect the fuel pump electrical connector (A);
    then turn the ignition switch to the ON position. The
    fuel pressure should build until the pump shuts off.
    Pressure should read 3.0 kg-cm2 (43.5 psi).
 4. If the pump is not running, disconnect the fuel
    pump/sensor connector (A).
 5. Connect a multimeter to the power supply leads with
    the red tester lead to the orange/red wire and the         XX342A
    black tester lead to the black wire; then turn the igni-    5. Using duct tape or other suitable means, cover the
    tion switch to the ON position. The meter should               fuel pump opening.
    read battery voltage. If battery voltage is indicated
    and the fuel pump does not run, replace the pump           Inspecting
    assembly. If no battery voltage is indicated, check                       AT THIS POINT
    the ECM, fuel relay, and fuse.
                                                               If the pump has failed earlier test and must be replaced,
Removing Fuel Pump Assembly                                    proceed to INSTALLING.
 1. Remove the key from the ignition switch.                    1. Inspect the fuel screen and blow clean with low pres-
                                                                   sure compressed air.
                  ! WARNING
                                                                2. Move the float lever and check for free movement.
Always ensure that power cannot be inadvertently
                                                                   The float assembly should return to the lower posi-
applied to the ignition/ECM when working on the fuel               tion without force.
system. If the ignition switch is turned on, the electric
fuel pump will start and gas could be rapidly pumped            3. Test the fuel level sensor by connecting a multimeter (A)
and spilled resulting in fire and severe injury.                   to the fuel level sensor leads (B); then select OHMS. The
                                                                   multimeter should show 5 ohms at full fuel position (C)
 2. Remove the passenger seat; then disconnect the neg-            and 95 ohms at empty fuel position (D).
    ative battery cable.
 3. Disconnect the electrical plug (A) from the main har-
    ness; then disconnect the fuel hose (B) from the fuel
    pump.


                                                               ATV2116

                                                               NOTE: If readings are erratic, clean the resistor
                                                               wiper and resistor with clean alcohol and retest. If
                                                               still not correct, replace the fuel pump assembly.
XX342

                                                               Replacing Fuel Level Sensor
                                                               To replace the fuel level sensor, use the following proce-
                                                               dure:
                                                                1. Cut the two blue wires (A) in the location shown.


                                                                                                                         89

--- Page 13 ---
Display            Fault Description                                            Possible Cause                              Fault Recovery Method
P0693    Fan-Secondary Relay Control Circuit         The secondary fan relay or its interconnect harness are shorted to Correct condition*
         Low/SG                                      ground.
P0694    Fan-Secondary Relay Control Circuit         The secondary fan relay or its interconnect harness are shorted to Correct condition*
         High/SP                                     battery power.
P1120    Throttle Position Sensor Lower Position     The electronic throttle valve was unable to cycle through its entire Correct condition*
                                                     self check range.
P1121    Throttle Position Sensor Lower Adaption The electronic throttle valve was unable to cycle through its entire Correct condition*
                                                     self check range.
P1122    Throttle Position Sensor Lower Return       The electronic throttle valve was unable to cycle through its entire Correct condition*
                                                     self check range.
P1123    Throttle Position Sensor Adaption           The electronic throttle valve was unable to cycle through its entire Correct condition*
         Condition                                   self check range.
P1124    Throttle Position Sensor Limp Home          The electronic throttle valve was unable to cycle through its entire Correct condition*
         Adaption                                    self check range.
P1125    Throttle Position Sensor Upper Position The electronic throttle valve was unable to cycle through its entire Correct condition*
                                                     self check range.
P1126    Throttle Position Sensor Upper Return       The electronic throttle valve was unable to cycle through its entire Correct condition*
                                                     self check range.
P2100    Throttle Actuator Control Motor Circuit     The electronic throttle control actuator or its interconnect harness is Correct condition*
         Open                                        open.
P2102    Throttle Actuator #1 Control Motor Circuit The electronic throttle control actuator or its interconnect harness is Correct condition*
         Low/SG                                      shorted to chassis ground.
P2103    Throttle Actuator #1 Control Motor Circuit The electronic throttle control actuator or its interconnect harness is Correct condition*
         High/SP                                     shorted to battery power.
P2106    Electronic Throttle Control Output is Out The ECM detected an internal condition.                                   Correct condition*
         Of Range
P2107    Electronic Throttle Control Driver          The ECM detected an internal condition.                                 Correct condition*
         Over-Temperature
P210C    Throttle Actuator #2 Control Motor Circuit The electronic throttle control actuator or its interconnect harness is Correct condition*
         Low/SG                                      shorted to chassis ground.
P210D    Throttle Actuator #2 Control Motor Circuit The electronic throttle control actuator or its interconnect harness is Correct condition*
         High/SP                                     shorted to battery power.
P2118    Throttle Actuator Control Motor Range       The electronic throttle control actuator wires or its interconnect      Correct condition*
         Error                                       harness are shorted together.
P2119    Throttle Control Actuator Control           Either the positive or the negative wire of the electronic throttle     Correct condition*
         Performance Error                           control actuator or its interconnect harness is open.
P2122    Pedal Position Sensor #1 Circuit            The pedal position sensor or its interconnect harness is shorted to Correct condition*
         Low/Open/SG                                 chassis ground or open.
P2123    Pedal Position Sensor #1 Circuit High/SP The pedal position sensor or its interconnect harness is shorted to Correct condition*
                                                     battery power.
P2127    Pedal Position Sensor #2 Circuit            The pedal position sensor or its interconnect harness is shorted to Correct condition*
         Low/Open/SG                                 chassis ground or open.
P2128    Pedal Position Sensor #2 Circuit High/SP The pedal position sensor or its interconnect harness is shorted to Correct condition*
                                                     battery power.
P2135    Throttle Position Sensor Plausibility Error One of the throttle position sensor circuits is shorted to either       Correct condition*
                                                     battery power, ground, is open, or a faulty sensor.
P2138    Pedal Position Sensor Plausibility Error One of the throttle position sensor circuits is shorted to either          Correct condition*
                                                     battery power, ground, is open, or a faulty sensor.
P2299    Brake Pedal Position/Accelerator Pedal The brake light pressure switch is active while the accelerator pedal Correct condition*
         Position Incompatible                       is being depressed.
P2300    Ignition Coil #1 Primary Circuit            Ignition coil #1 primary circuit or its interconnect harness is open or Correct condition**
         Low/SG/Open                                 shorted to chassis ground.
P2301    Ignition Coil #1 Primary Circuit High       Ignition coil #1 primary circuit or its interconnect harness is shorted Correct condition**
                                                     to battery power.
P2303    Ignition Coil #2 Primary Circuit Low/Open Ignition coil #2 primary circuit or its interconnect harness is open or Correct condition**
                                                     shorted to chassis ground.
P2304    Ignition Coil #2 Primary Circuit High       Ignition coil #2 primary circuit or its interconnect harness is shorted Correct condition**
                                                     to battery power.
P2306    Ignition Coil #3 Primary Circuit Low/Open Ignition coil #3 primary circuit or its interconnect harness is open or Correct condition**
                                                     shorted to chassis ground.
P2307    Ignition Coil #3 Primary Circuit High       Ignition coil #3 primary circuit or its interconnect harness is shorted Correct condition**
                                                     to battery power.
P2610    ECU Warm Reset                              System voltage may have been temporarily too low to power the Correct condition*
                                                     ECU.
U0100    Lost Communication with ECM                 The ECM CAN circuit or its interconnect harness is intermittent or Correct condition*
                                                     has failed.
U0155    LCD Gauge to ECM CAN                        The LCD gauge CAN circuit or its interconnect harness is                Correct condition*
         Communication Lost                          intermittent or has failed.
FUEL OFF Tilt Sensor Activation Code                 The chassis tilt sensor has been activated.                             Correct condition*
     High: A high voltage condition has been detected.                           * After correcting the condition, cycle the key switch On-Off-On.
     Low: A low voltage condition has been detected.                             ** After correcting the condition, cycle the key switch On-Off-On, start the
     Intermittent: An intermittent circuit condition has been detected.             engine and drive vehicle, then cycle the key switch On-Off-On.
     Open: An open circuit condition has been detected.


                                                                                                                                                                99

--- Page 14 ---
Disassembling Differential Assembly

View the complete manual on HeyDownloads →