PDF Service Manual 2010 Yamaha XT1200Z - 2 MB

Keep your 2010 Yamaha XT1200Z Super Ténéré motorcycle in top condition with the official service manual.

This comprehensive guide provides detailed instructions for maintenance, troubleshooting, and major repairs.

It's the same manual used by professional Yamaha technicians.

Whether you're a DIY enthusiast or a seasoned mechanic, this PDF is essential for servicing your bike correctly.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
2010

SERVICE MANUAL

 XT1200Z(Z)


              23P-28197-E0

--- Page 3 ---
FEATURES

EAS20170

FEATURES
EAS30340

OUTLINE OF THE FI SYSTEM
The main function of a fuel supply system is to provide fuel to the combustion chamber at the optimum
air-fuel ratio in accordance with the engine operating conditions and the atmospheric temperature. In
the conventional carburetor system, the air-fuel ratio of the mixture that is supplied to the combustion
chamber is created by the volume of the intake air and the fuel that is metered by the jet used in the
respective carburetor.
Despite the same volume of intake air, the fuel volume requirement varies by the engine operating con-
ditions, such as acceleration, deceleration, or operating under a heavy load. Carburetors that meter the
fuel through the use of jets have been provided with various auxiliary devices, so that an optimum air-
fuel ratio can be achieved to accommodate the constant changes in the operating conditions of the en-
gine.
As the requirements for the engine to deliver more performance and cleaner exhaust gases increase,
it becomes necessary to control the air-fuel ratio in a more precise and finely tuned manner. To accom-
modate this need, this model has adopted an electronically controlled fuel injection (FI) system, in place
of the conventional carburetor system. This system can achieve an optimum air-fuel ratio required by
the engine at all times by using a microprocessor that regulates the fuel injection volume according to
the engine operating conditions detected by various sensors.
The adoption of the FI system has resulted in a highly precise fuel supply, improved engine response,
better fuel economy, and reduced exhaust emissions.

                                     1
                                                      2,3
                                                            4
                                                                5,6,7,8
                                                                   9      10   11


               18


                                         17   15,16     14        13                             12
  1. Engine trouble warning light                               11. Lean angle sensor
  2. Ignition coils                                             12. Rear wheel sensor
  3. Spark plugs                                                13. Coolant temperature sensor
  4. Intake air temperature sensor                              14. Crankshaft position sensor
  5. Throttle position sensor                                   15. O2 sensor #1
  6. Accelerator position sensor                                16. O2 sensor #2
  7. Intake air pressure sensor                                 17. Battery
  8. Throttle servo motor                                       18. ECU (engine control unit)
  9. Fuel injectors
  10. Fuel pump

                                                      1-2

--- Page 4 ---
FEATURES

                              A
                                                    b


                                     a
                                               c


                                                                        d
                             B
                                                        e

                                                   f
                                      a


                                                    g
                                                                    d
 a. Friction force between the tire and road                e. Less slippery road surface
    surface                                                 f. Controlling zone
 b. Brake force                                             g. Slippery road surface
 c. Side force
 d. Slip ratio (%)


Wheel slip and hydraulic control
The ABS ECU calculates the wheel speed of each wheel according to the rotation signal received from
the front and rear wheel sensors. In addition, the ABS ECU calculates the vehicle chassis speed and
the rate of speed reduction based on the wheel speed values.
The difference between the chassis speed and the wheel speed calculated in the slip ratio formula is
equal to the wheel slip. When the wheel speed is suddenly reduced, the wheel has a tendency to lock.
When the wheel slip and the wheel speed reduction rate exceed the preset values, the ABS ECU de-
termines that the wheel has a tendency to lock.
If the slip is large and the wheel has a tendency to lock (point “A” in the following figure), the ABS ECU
reduces the hydraulic pressure in the brake caliper. Once the ABS ECU determines that the tendency
of the wheel to lock has diminished after the hydraulic pressure is reduced, it increases the hydraulic
pressure (point “B” in the following figure). The hydraulic pressure is initially increased quickly, and then
it is increased gradually.


                                                   1-12

--- Page 5 ---
FEATURES

UBS (ABS not activated and UBS activated)
Brake lever input only
Front brakes:
When the ABS is not activated, the inlet solenoid valve is open and the outlet solenoid valve is closed
because a control signal has not been transmitted from the ABS ECU. Therefore, when the brake lever
is squeezed, the hydraulic pressure in the front brake master cylinder increases and the brake fluid is
sent to the front brake calipers. At this time, the hydraulic pump check valve is closed. The front brake
master cylinder directly pressurizes the front brake calipers during normal braking. When the brake le-
ver is released, the brake fluid in the front brake calipers returns to the front brake master cylinder.
Rear brake:
When the brake lever is squeezed, the ABS ECU detects the hydraulic pressure using the front brake
master cylinder pressure sensor and operates the hydraulic pump. At this time, the ABS is not activat-
ed, the inlet solenoid valve is open, and the outlet solenoid valve is closed because a control signal has
not been transmitted from the ABS ECU. The shuttle solenoid valve opens and closes according to the
UBS control signals from the ABS ECU. The hydraulic pump draws in the brake fluid from the rear brake
master cylinder and automatically pressurizes the rear brake caliper.
If the brake pedal is depressed, the UBS automatic pressurization stops. The ABS ECU detects and
controls the hydraulic pressure in the rear brake caliper using the front brake master cylinder pressure
sensor, rear brake master cylinder pressure sensor, and rear brake caliper pressure sensor.

                                             a                                                           A
                          1                                  3
                                          2                                      4

                                                                                               6
              11                   8                         8                                      5
                                        10         10
                                                            9
                                                        b                                  7

                                                                                           c
                                         15      15     14
                       12 13                                       13 12


                                                      16

                              18                                         17

 1. Front brake master cylinder                                 13. Outlet solenoid valve
 2. Brake lever                                                 14. Check valve
 3. Rear brake master cylinder                                  15. Buffer chamber
 4. Brake pedal                                                 16. Rear brake caliper pressure sensor
 5. Rear brake master cylinder pressure sensor                  17. Rear brake caliper
 6. Separation solenoid valve                                   18. Front brake calipers
 7. Shuttle solenoid valve
                                                                A. Pressurize
 8. Damping chamber
                                                                a. Input
 9. ABS motor
                                                                b. Hydraulic pump is operating
 10. Hydraulic pump
                                                                c. Shuttle solenoid valve is open
 11. Front brake master cylinder pressure sensor
 12. Inlet solenoid valve

                                                   1-22

--- Page 6 ---
FEATURES

Odometer and tripmeter modes                                 Clock


                                               1                                                          1


                    2                                                              3   2
1. Odometer/tripmeter/fuel reserve tripmeter                 1. Clock
2. Left set button                                           2. Right set button
                                                             3. Left set button
Pushing the left button switches the display be-
tween the odometer mode “ODO” and the trip-                  The clock displays when the key is turned to
meter modes “TRIP 1” and “TRIP 2” in the                     “ON”. In addition, the clock can be displayed for
following order:                                             10 seconds by pushing the left button when the
ODO → TRIP 1 → TRIP 2 → ODO                                  main switch is in the “OFF”, “LOCK” or “Parking”
TIP                                                          position.
When selecting “TRIP 1” or “TRIP 2”, the display             To set the clock:
flashes for five seconds.                                    1. Push the left button and right button together
                                                                for at least three seconds.
When approximately 3.9 L (1.03 US gal, 0.86                  2. When the hour digits start flashing, push the
Imp.gal) of fuel remains in the fuel tank, the dis-             right button to set the hours.
play automatically changes to the fuel reserve               3. Push the left button; the minute digits start
tripmeter mode “TRIP F” and starts counting the                 flashing.
distance traveled from that point. In that case,             4. Push the right button to set the minutes.
pushing the left button switches the display be-             5. Push the left button; the clock starts after the
tween the various tripmeter and odometer                        button is released.
modes in the following order:
TRIP F → ODO → TRIP 1 → TRIP 2 → TRIP F                      Fuel meter
TIP
When selecting “TRIP 1”, “TRIP 2” or “TRIP F”,
the display flashes for five seconds.
To reset a tripmeter, select it by pushing the left
button, and then push this button for at least one
second while the display is flashing. If you do not
reset the fuel reserve tripmeter manually, it re-
sets itself automatically and the display returns
to the prior mode after refueling and traveling 5                                                   1
km (3 mi).
                                                             1. Fuel meter
                                                             The fuel meter indicates the amount of fuel in the
                                                             fuel tank. The display segments of the fuel meter
                                                             disappear towards “E” (Empty) as the fuel level
                                                             decreases. When the last segment starts flash-
                                                             ing, refuel as soon as possible.
                                                             When the key is turned to “ON”, all display seg-
                                                             ments come on once in order to test the electri-
                                                             cal circuit.


                                                      1-32

--- Page 7 ---
BASIC SERVICE INFORMATION


                                                       2. Check:
Checking the connections                                • Lead
Check the leads, couplers, and connectors for           • Coupler
stains, rust, moisture, etc.                            • Connector
1. Disconnect:                                            Moisture → Dry with an air blower.
  • Lead                                                  Rust/stains → Connect and disconnect sev-
  • Coupler                                               eral times.
  • Connector
ECA16780

NOTICE
• When disconnecting a coupler, release the
  coupler lock, hold both sections of the cou-
  pler securely, and then disconnect the cou-
  pler.
• There are many types of coupler locks;
  therefore, be sure to check the type of cou-
  pler lock before disconnecting the coupler.

                                                       3. Check:
                                                        • All connections
                                                          Loose connection → Connect properly.
                                                   TIP
                                                       • If the pin “1” on the terminal is flattened, bend
                                                         it up.
                                                       • After disassembling and assembling a coupler,
                                                         pull on the leads to make sure that they are in-
                                                         stalled securely.

ECA16790

NOTICE
When disconnecting a connector, do not pull
the leads. Hold both sections of the connec-
tor securely, and then disconnect the con-
nector.

                                                                                            1


                                                1-42

--- Page 8 ---
SPECIFICATIONS

GENERAL SPECIFICATIONS ........................................................................ 2-1


ENGINE SPECIFICATIONS ............................................................................ 2-2


CHASSIS SPECIFICATIONS ........................................................................ 2-10


ELECTRICAL SPECIFICATIONS ................................................................. 2-13


TIGHTENING TORQUES .............................................................................. 2-16
                                                                                                                    2
   GENERAL TIGHTENING TORQUE SPECIFICATIONS......................... 2-16
   ENGINE TIGHTENING TORQUES......................................................... 2-17
   CHASSIS TIGHTENING TORQUES....................................................... 2-22


LUBRICATION POINTS AND LUBRICANT TYPES .................................... 2-28
   ENGINE................................................................................................... 2-28
   CHASSIS................................................................................................. 2-30


LUBRICATION SYSTEM CHART AND DIAGRAMS.................................... 2-31
   ENGINE OIL LUBRICATION CHART ..................................................... 2-31
   LUBRICATION DIAGRAMS .................................................................... 2-33


COOLING SYSTEM DIAGRAMS .................................................................. 2-41


CABLE ROUTING ......................................................................................... 2-43

--- Page 9 ---
CHASSIS SPECIFICATIONS

EAS20300

CHASSIS SPECIFICATIONS
Chassis
 Frame type                                         Steel tube backbone
 Caster angle                                       28.00°
 Trail                                              126.0 mm (4.96 in)

Front wheel
  Wheel type                                        Spoke wheel
  Rim size                                          19M/C × MT2.50
  Rim material                                      Aluminum
  Wheel travel                                      190.0 mm (7.48 in)
  Radial wheel runout limit                         2.0 mm (0.08 in)
  Lateral wheel runout limit                        2.0 mm (0.08 in)

Rear wheel
 Wheel type                                         Spoke wheel
 Rim size                                           17M/C × MT4.00
 Rim material                                       Aluminum
 Wheel travel                                       190.0 mm (7.48 in)
 Radial wheel runout limit                          2.0 mm (0.08 in)
 Lateral wheel runout limit                         2.0 mm (0.08 in)

Front tire
  Type                                              Tubeless
  Size                                              110/80R19M/C 59V
  Manufacturer/model                                BRIDGESTONE/BW-501
                                                    METZELER/TOURANCE EXP FRONT C
   Wear limit (front)                               1.6 mm (0.06 in) (Europe)
                                                    1.0 mm (0.04 in) (AUS)

Rear tire
 Type                                               Tubeless
 Size                                               150/70R17M/C 69V
 Manufacturer/model                                 BRIDGESTONE/BW-502
                                                    METZELER/TOURANCE EXP C
   Wear limit (rear)                                1.6 mm (0.06 in) (Europe)
                                                    1.0 mm (0.04 in) (AUS)

Tire air pressure (measured on cold tires)
  Loading condition                                 0–90 kg (0–198 lb)
     Front                                          225 kPa (2.25 kgf/cm², 33 psi)
     Rear                                           250 kPa (2.50 kgf/cm², 36 psi)
  Loading condition                                 90–209 kg (198–461 lb)
     Front                                          225 kPa (2.25 kgf/cm², 33 psi)
     Rear                                           290 kPa (2.90 kgf/cm², 42 psi)

Front brake
  Type                                              Dual disc brake
  Operation                                         Right hand operation
  Front disc brake
    Disc outside diameter × thickness               310.0 × 4.5 mm (12.20 × 0.18 in)


                                             2-10

--- Page 10 ---
TIGHTENING TORQUES

                                      Thread
                Item                         Q’ty               Tightening torque               Remarks
                                       size
Oil pipe bolt                            M6       3        10 Nm (1.0 m·kgf, 7.2 ft·lbf)             LT


Oil pump assembly bolt                  M6        3        12 Nm (1.2 m·kgf, 8.7 ft·lbf)
Oil pump housing cover bolt              M6       6        10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Oil strainer (oil pump) bolt            M6        3        10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Main axle assembly bolt                  M6       3        12 Nm (1.2 m·kgf, 8.7 ft·lbf)             LT


Shift drum retainer screw               M6        2        10 Nm (1.0 m·kgf, 7.2 ft·lbf)             LT


Shift shaft spring stopper bolt          M8       1         22 Nm (2.2 m·kgf, 16 ft·lbf)             LT


Connecting rod nut                      M9        4                   See TIP.                        M

Middle gear side cover screw            M6        6        10 Nm (1.0 m·kgf, 7.2 ft·lbf)             LT


Middle gear side cover damper
                                        M6        2        10 Nm (1.0 m·kgf, 7.2 ft·lbf)             LT
plate screw
Engine oil drain bolt (middle
                                        M8        1         20 Nm (2.0 m·kgf, 14 ft·lbf)
gear)
Middle driven pinion gear bearing
                                        M8        4         33 Nm (3.3 m·kgf, 24 ft·lbf)             LT
housing bolt
Middle drive pinion gear bearing
                                        M8        4         28 Nm (2.8 m·kgf, 20 ft·lbf)             LT
retainer bolt
Middle drive pinion gear nut            M44       1        110 Nm (11 m·kgf, 80 ft·lbf)          Stake.
Starter motor assembly bolt             M6        2        12 Nm (1.2 m·kgf, 8.7 ft·lbf)
Starter motor terminal nut               M6       1         5 Nm (0.5 m·kgf, 3.6 ft·lbf)
Starter motor front cover bolt           M5       2         5 Nm (0.5 m·kgf, 3.6 ft·lbf)
Starter motor terminal and rear
                                        M6        1        11 Nm (1.1 m·kgf, 8.0 ft·lbf)
cover nut

TIP
Cylinder head bolt
Tighten the cylinder head bolts “1”–”8” in the proper tightening sequence as follows:
• Tighten the cylinder head bolts “1”–“6” to 20 Nm (2.0 m·kgf, 14 ft·lbf).
• Tighten the cylinder head bolts “1”–“6” to 30 Nm (3.0 m·kgf, 22 ft·lbf), and then tighten them further to
  reach the specified angle. Tighten each bolt to the specified angle before tightening the next bolt to
  30 Nm (3.0 m·kgf, 22 ft·lbf).
  “1”, “2”, “4”: 215–225°
  “3”, “5”, “6”: 180–190°
• Tighten the cylinder head bolts “7” and “8” to 10 Nm (1.0 m·kgf, 7.2 ft·lbf).

                                                  1

                                  3                               6
                                                                        8


                                  5                                     7
                                                                  4

                                                  2


                                                  2-20

--- Page 11 ---
LUBRICATION POINTS AND LUBRICANT TYPES

EAS20380

CHASSIS
                               Lubrication point                                 Lubricant
 Steering bearings                                                                  LS


 Steering bearing oil seal lips                                                     LS


 Steering shaft and nut thread                                                      LS


 Front wheel oil seal lips (right and left)                                         LS


 Rear wheel oil seal lip                                                            LS


 Rear wheel drive hub mating surface                                                LS


 Rear brake pedal pivoting point and metal-to-metal moving parts                    LS


 Passenger footrest pivoting point and ball                                         LS


 Shift pedal pivoting point and metal-to-metal moving parts                         LS


 Centerstand pivoting point and metal-to-metal moving parts                         LS


 Centerstand spring hook metal-to-metal moving parts                                LS


 Sidestand pivoting point and metal-to-metal moving parts                           LS


 Link and sidestand switch contact point                                            LS


 Sidestand hook and link contact point                                              LS


 Tube guide (throttle grip) inner surface and throttle cables                       LS

 Brake lever pivoting point, brake master cylinder push rod contact surface,
                                                                                    S
 and metal-to-metal moving parts
 Clutch lever pivoting point, clutch master cylinder push rod contact surface,
                                                                                    S
 and metal-to-metal moving parts
 Pivot shaft and pivot shaft thread                                                 LS


 Pivot shaft bearing                                                                LS


 Pivot shaft dust cover inner surface                                               LS


 Relay arm bearings and oil seal lips                                               LS


                                                 2-30

--- Page 12 ---
LUBRICATION SYSTEM CHART AND DIAGRAMS

1.   Oil pump assembly
2.   Oil filter cartridge
3.   Oil strainer cover
4.   Oil strainer (oil pan)
5.   Oil pan
6.   Lower crankcase
7.   Upper crankcase
8.   Rear balancer shaft


                                         2-40

--- Page 13 ---
CABLE ROUTING

AA.Route the immobilizer unit lead to the inside of the
    throttle cables.
AB.Position the immobilizer unit coupler below the
    brake hose (front brake master cylinder to
    hydraulic unit).
AC.Upward
AD.Route the throttle cables between the brake hose
    (front brake master cylinder to hydraulic unit) and
    the clutch hose.
AE.Route the front wheel sensor lead to the outside of
    the brake hose (front brake master cylinder to
    hydraulic unit), clutch hose, and throttle cables.
AF. Route the radiator fan motor lead over the front
    wheel sensor lead.
AG.Route the horn lead between the brake hose (front
    brake master cylinder to hydraulic unit) and the
    clutch hose, and to the inside of the throttle cables.
AH.Forward
AI. Face the buckle of the plastic band rearward with
    the end pointing downward. Do not cut off the
    excess end of the plastic locking tie.
AJ. Fasten the immobilizer unit lead at the white tape
    to the brake hose (front brake master cylinder to
    hydraulic unit) with a plastic locking tie. Face the
    buckle of the plastic locking tie forward with the end
    pointing downward. Do not cut off the excess end
    of the plastic locking tie.


                                                             2-50

--- Page 14 ---
CABLE ROUTING

1. Headlight relay                                                 J. Install the positive battery lead terminal and
2. Turn signal/hazard relay                                           negative battery lead terminal to the starter relay
                                                                      so that the terminals are parallel to the relay as
3. Radiator fan motor relay                                           shown in the illustration.
4. Main fuse                                                       K. Route the fuse box 1 lead and fuse box 2 lead to
5. Starting circuit cut-off relay                                     the inside of the wire harness (starting circuit cut-
6. Rectifier/regulator coupler                                        off relay lead and starter relay lead).
7. Stator coil coupler                                             L. Install the grip warmer coupler so that the coupler
                                                                      cap is facing inward.
8. Joint connector
                                                                   M. Install the accessory light coupler so that the
9. Battery                                                            coupler cap is facing inward.
10. Positive battery lead                                          N. Route the leads that pass through the rubber cover
11. Crankshaft position sensor coupler                                to the inside of the fuse box 1 lead and fuse box 2
12. Negative battery lead coupler                                     lead.
13. Negative battery lead                                          O. Route the leads that pass through the rubber cover
                                                                      to the inside of the wire harness (starting circuit
14. Starter relay                                                     cut-off relay lead and starter relay lead).
15. Fuse box 1                                                     P. Route the wire harness (turn signal/hazard relay
16. Fuse box 2                                                        lead, radiator fan motor relay lead, and headlight
17. Grip warmer coupler                                               relay lead) and ECU leads upward, making sure to
                                                                      route the ECU leads to the rear of the wire
18. Accessory light coupler                                           harness.
19. Left handlebar switch coupler                                  Q. Route the stator coil lead to the rear of the wire
20. Stator coil lead                                                  harness.
21. ECU leads                                                      R. Fasten the wire harness with the holder on the
22. O2 sensor #1 coupler                                              electrical components tray.
                                                                   S. Route the leads that pass through the rubber cover
23. Right handlebar switch couplers                                   to the outside of the ECU leads.
24. Wire harness (turn signal/hazard relay lead and                T. Fasten the headlight relay lead, turn signal/hazard
    radiator fan motor relay lead)                                    relay lead, radiator fan motor relay lead and
25. Starting circuit cut-off relay lead                               starting circuit cut-off relay lead with the holders on
26. Starter relay lead                                                the ECU bracket.
27. Rectifier/regulator lead                                       U. Install the rubber holder on each relay completely
                                                                      onto its respective tab on the ECU bracket.
28. Fuse box 2 lead
                                                                   V. Face the catch of the holder forward.
29. Fuse box 1 lead
                                                                   W. Route the starting circuit cut-off relay lead to the
30. Wire harness                                                      front of the wire harness (turn signal/hazard relay
31. Wire harness (starting circuit cut-off relay lead and             lead, radiator fan motor relay lead, and headlight
    starter relay lead)                                               relay lead).
32. Wire harness (rectifier/regulator lead and stator              X. Route the starter relay lead to the front of the wire
    coil lead)                                                        harness (turn signal/hazard relay lead, radiator fan
33. Left handlebar switch lead                                        motor relay lead, and headlight relay lead).
34. O2 sensor #1 lead                                              Y. Route the rectifier/regulator lead and fuse box 2
                                                                      lead as shown in the illustration.
35. Right handlebar switch lead
                                                                   Z. Route the stator coil lead to the outside and to the
36. Main switch lead                                                  front of the fuse box 1 lead.
37. O2 sensor #2 lead
A. Route the main fuse leads to the outside of the
   headlight relay lead and turn signal/hazard relay
   lead.
B. Fasten the main fuse leads with the holder on the
   ECU bracket.
C. Route the main fuse leads between the starter
   relay and the joint connector.
D. Slide the rubber cover over the couplers, making
   sure that the couplers are covered completely.
E. Either coupler, the crankshaft position sensor
   coupler or negative battery lead coupler, may be
   positioned to the outside.
F. Install the starter relay rubber holder completely
   onto the tabs on the ECU bracket.
G. Make sure that the terminal covers for the positive
   battery lead and negative battery lead are not fitted
   over the rib on the starter relay.
H. Fit the joint connector into the holder on the ECU
   bracket.
I. Route the starter relay lead to the outside of the
   main fuse leads.


                                                            2-60

--- Page 15 ---
CABLE ROUTING

1. Engine ground lead
2. Wire harness
3. ABS ECU lead
4. ABS test coupler
5. ABS test coupler lead
6. Hydraulic unit assembly
7. Coolant reservoir hose
8. Oil level switch lead
9. Sidestand switch lead
10. Fuel hose
11. Rear brake light switch lead
12. Neutral switch lead
13. Fuel pump lead
14. Rear right turn signal light lead
15. Lean angle sensor sub-wire harness/frame ground
    lead
16. Tail/brake light lead
17. License plate light lead
18. Rear left turn signal light lead
19. Fuel pump coupler
A. Make sure that the engine ground lead terminal
    contacts the stopper on the crankcase.
B. Position the plastic band between the rubber cover
    and the split in the wire harness.
C. Insert the projection on the plastic band into the
    hole in the rear fender, and then fasten the ABS
    ECU lead and wire harness with the band. Route
    the wire harness to the outside of the ABS ECU
    lead. Point the end of the plastic band to the right
    and insert it into the hole in the frame. Do not cut
    off the excess end of the plastic band.
D. Slide the rubber cover over the rear turn signal
    light connectors, license plate light coupler,
    tail/brake light coupler, lean angle sensor sub-wire
    harness coupler, and alarm couplers, making sure
    that the connectors and couplers are covered
    completely.
E. Slide the rubber cover over the sidestand switch
    coupler, rear brake light switch coupler, neutral
    switch coupler, rear wheel sensor coupler, and oil
    level switch coupler, making sure that the couplers
    are covered completely.
F. Route the sidestand switch lead and oil level
    switch lead over the coolant reservoir hose.
G. Connect the ABS ECU coupler, and then fasten
    the wire harness at the white tape with the plastic
    band. Point the end of the plastic band downward.
    Do not cut off the excess end of the plastic band.
H. Point the end of the plastic band rearward. Do not
    cut off the excess end of the plastic band.
I. Fold the ABS test coupler lead, and then fasten the
    ABS test coupler lead, lean angle sensor sub-wire
    harness, rear right turn signal light lead, rear left
    turn signal light lead, tail/brake light lead, and
    license plate light lead with the plastic locking tie.
J. Position the plastic locking tie 40–60 mm (1.57–
    2.36 in) from the edge of the holder.
K. Fit the ABS test coupler in between the ABS unit
    cover and the holder.
L. Face the catch of the holder forward or rearward.
M. Route the fuel pump lead above and to the rear of
    the fuel hose.
N. Forward


                                                             2-70

--- Page 16 ---
PERIODIC MAINTENANCE

EAS21030

CHECKING THE FUEL LINE
1. Remove:
 • Rider seat                                                             2
 • Left side cowling

View the complete manual on HeyDownloads →