PDF Service Manual 2000 NISSAN PATHFINDER R50 - 2 MB
This is the official factory service manual for the 2000 Nissan Pathfinder R50 series.
It contains comprehensive instructions for every repair and maintenance procedure you could need.
Whether you are a professional mechanic or a DIY enthusiast, this manual provides the detailed specifications and step-by-step guidance to get the job done right.
Keep your Pathfinder running like new.
PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
PDF viewer loading area
Text Preview from This Manual
The text below was extracted from the visible preview pages to help you confirm the manual contents before download.
--- Page 1 ---
Edition: August 1999 QUICK REFERENCE INDEX
Revision: July 2000
Publication No. SM0E-1R50U2
All rights reserved. No part of this Service Manual may be
reproduced or stored in a retrieval system, or transmitted in
any form, or by any means, electronic, mechanical, photo-
copying, recording or otherwise, without the prior written
permission of Nissan Motor Company Ltd., Tokyo, Japan.
--- Page 3 ---
EXIT
OVERALL SYSTEM
Shift Mechanism (Cont’d)
CLUTCH AND BAND CHART NAAT0012S03
GI
Band servo For-
Low
For- Over- ward Low &
Shift posi- Reverse High
ward run one
one-
reverse Lock-up Remarks
MA
tion clutch clutch 2nd 3rd 4th way
clutch clutch -way brake
apply release apply clutch
clutch
EM
PARK
P
POSITION
REVERSE
LC
R q q
POSITION
N
NEUTRAL EC
POSITION
1st q *1D B B
Automatic
FE
2nd q *1A q B shift
D*4
3rd q q *1A *2C C B *5q 1k2k3
k4 CL
4th q C *3C C q q
1st q q B B Automatic MT
2 shift
2nd q q q B 1k2
1st q q B B q Locks (held
stationary) in
1
1st speed
2nd q q q B 1g2 TF
*1: Operates when overdrive control switch is being set in “OFF” position.
*2: Oil pressure is applied to both 2nd “apply” side and 3rd “release” side of band servo piston. However, brake band does not contract PD
because oil pressure area on the “release” side is greater than that on the “apply” side.
*3: Oil pressure is applied to 4th “apply” side in condition *2 above, and brake band contracts.
*4: A/T will not shift to 4th when overdrive control switch is set in “OFF” position.
*5: Operates when overdrive control switch is “OFF”.
AX
q : Operates.
A: Operates when throttle opening is less than 3/16, activating engine brake.
SU
B: Operates during “progressive” acceleration.
C: Operates but does not affect power transmission.
D: Operates when throttle opening is less than 3/16, but does not affect engine brake. BR
ST
RS
BT
HA
SC
EL
IDX
AT-17
--- Page 4 ---
EXIT
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
CONSULT (Cont’d)
SELF-DIAGNOSTIC PROCEDURE (WITH CONSULT)
NAAT0184S01
1. Turn on CONSULT and touch “ENGINE” for OBD-II detected
items or touch “A/T” for TCM self-diagnosis.
If A/T is not displayed, check TCM power supply and ground
circuit. Refer to AT-92. If result is NG, refer to EL-9, “Sche-
matic”.
SAT038J
2. Touch “SELF-DIAG RESULTS”.
Display shows malfunction experienced since the last erasing
operation.
CONSULT performs REAL-TIME SELF-DIAGNOSIS.
Also, any malfunction detected while in this mode will be dis-
played at real time.
SAT416J
SELF-DIAGNOSTIC RESULT TEST MODE NAAT0184S02
TCM self-diagnosis OBD-II (DTC)
Detected items
(Screen terms for CONSULT, “SELF-DIAG
RESULTS” test mode)
Malfunction is detected when ... Available by
Available by
malfunction
O/D OFF
indicator lamp*2,
“A/T” “ENGINE” indicator lamp or
“ENGINE” on CON-
“A/T” on CONSULT
SULT or GST
PNP switch circuit I TCM does not receive the cor-
rect voltage signal (based on
— P0705
PNP SW/CIRC the gear position) from the
— switch.
Revolution sensor I TCM does not receive the
proper voltage signal from the X P0720
VHCL SPEED VEH SPD SEN/CIR sensor.
SEN·A/T AT
Vehicle speed sensor (Meter) I TCM does not receive the
proper voltage signal from the X —
VHCL SPEED sensor.
—
SEN·MTR
A/T 1st gear function I A/T cannot be shifted to the 1st
gear position even if electrical — P0731*1
— A/T 1ST GR FNCTN circuit is good.
A/T 2nd gear function I A/T cannot be shifted to the 2nd
gear position even if electrical — P0732*1
— A/T 2ND GR FNCTN circuit is good.
A/T 3rd gear function I A/T cannot be shifted to the 3rd
gear position even if electrical — P0733*1
— A/T 3RD GR FNCTN circuit is good.
A/T 4th gear function I A/T cannot be shifted to the 4th
gear position even if electrical — P0734*1
— A/T 4TH GR FNCTN circuit is good.
AT-38
--- Page 5 ---
EXIT
TROUBLE DIAGNOSIS — BASIC INSPECTION
A/T Fluid Check
A/T Fluid Check NAAT0021
GI
FLUID LEAKAGE CHECK NAAT0021S01
1. Clean area suspected of leaking. — for example, mating sur-
face of converter housing and transmission case.
MA
2. Start engine, apply foot brake, place selector lever in “D” posi-
tion and wait a few minutes. EM
3. Stop engine.
4. Check for fresh leakage.
LC
FLUID CONDITION CHECK EC
NAAT0021S02
Fluid color Suspected problem
FE
Dark or black with burned odor Wear of frictional material
Water contamination — Road water
Milky pink
entering through filler tube or breather CL
Varnished fluid, light to dark brown Oxidation — Over or under filling, —
and tacky Overheating MT
SAT638A
FLUID LEVEL CHECK NAAT0021S03
Refer to MA-24, “Checking A/T Fluid”.
TF
PD
AX
SU
Stall Test NAAT0022
STALL TEST PROCEDURE NAAT0022S01 BR
1. Check A/T fluid and engine oil levels. If necessary, add fluid
and oil.
2. Drive vehicle for approx. 10 minutes or until fluid and oil reach ST
operating temperature.
ATF operating temperature:
RS
50 - 80°C (122 - 176°F)
SAT647B BT
3. Set parking brake and block wheels.
4. Install a tachometer where it can be seen by driver during test. HA
I It is good practice to put a mark on point of specified
engine rpm on indicator.
SC
EL
IDX
SAT513G
AT-59
--- Page 6 ---
EXIT
TROUBLE DIAGNOSIS — BASIC INSPECTION
Road Test (Cont’d)
7 CHECK ENGINE BRAKE
Does vehicle decelerate by engine brake?
SAT778B
Yes or No
Yes © 1. Stop vehicle.
2. Perform self-diagnosis. Refer to TCM SELF-DIAGNOSTIC PROCEDURE (No Tools),
AT-46.
No © Go to “20. Vehicle Does Not Decelerate By Engine Brake”, AT-247.
AT-80
--- Page 7 ---
EXIT
DTC P0705 PARK/NEUTRAL POSITION SWITCH
Wiring Diagram — AT — PNP/SW
Wiring Diagram — AT — PNP/SW NAAT0186
GI
MA
EM
LC
EC
FE
CL
MT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
MAT753A
IDX
AT-101
--- Page 8 ---
EXIT
DTC P0731 IMPROPER SHIFTING TO 1ST GEAR POSITION
Description (Cont’d)
2,2,3,3
Malfunction for P0731 exists.
4,3,3,4
8) Make sure that “OK” is displayed. (If “NG” is displayed, refer
to “DIAGNOSTIC PROCEDURE”.)
Refer to “DIAGNOSTIC PROCEDURE”, AT-124.
Refer to shift schedule, AT-345.
With GST
1) Start engine and warm up ATF.
2) Accelerate vehicle to 20 to 25 km/h (12 to 16 MPH) under the
following condition and release the accelerator pedal com-
pletely.
THROTTLE POSI: Less than 1.0/8
Selector lever: D position (OD “ON”)
Refer to shift schedule, AT-345.
3) Depress accelerator pedal to WOT (more than 7.0/8 of
“THROTTLE POSI”) quickly from a speed of 20 to 25 km/h (12
to 16 MPH). (It will take approximately 3 seconds.)
4) Select “MODE 7” with GST.
No Tools
1) Start engine and warm up ATF.
2) Accelerate vehicle to 20 to 25 km/h (12 to 16 MPH) under the
following condition and release the accelerator pedal com-
pletely.
THROTTLE POSI: Less than 1.0/8
Selector lever: D position (OD “ON”)
Refer to shift schedule, AT-345.
3) Depress accelerator pedal to WOT (more than 7.0/8 of
“THROTTLE POSI”) quickly from a speed of 20 to 25 km/h (12
to 16 MPH). (It will take approximately 3 seconds.)
4) Perform self-diagnosis for ECM.
Refer to EC section [“Malfunction Indicator Lamp (MIL)”, “ON
BOARD DIAGNOSTIC SYSTEM DESCRIPTION”].
AT-122
--- Page 9 ---
EXIT
DTC P0734 IMPROPER SHIFTING TO 4TH GEAR POSITION
Diagnostic Procedure
Diagnostic Procedure NAAT0049
GI
1 CHECK SHIFT UP (D3 TO D4)
During “Cruise test − Part 1”, AT-71. MA
Does A/T shift from D3 to D4 at the specified speed?
EM
LC
EC
FE
SAT988H
Yes or No CL
Yes © GO TO 9.
No © GO TO 2. MT
2 CHECK LINE PRESSURE
Perform line pressure test. Refer to AT-62.
OK or NG
TF
OK © GO TO 3.
NG © GO TO 6.
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
AT-143
--- Page 10 ---
EXIT
DTC P0745 LINE PRESSURE SOLENOID VALVE
Wiring Diagram — AT — LPSV
Wiring Diagram — AT — LPSV NAAT0196
MAT763A
AT-164
--- Page 11 ---
EXIT
DTC P1705 THROTTLE POSITION SENSOR
Diagnostic Procedure (Cont’d)
3 CHECK THROTTLE POSITION SWITCH CIRCUIT (With CONSULT) GI
With CONSULT
1. Turn ignition switch to “ON” position. MA
(Do not start engine.)
2. Select “ECU INPUT SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT.
3. Apply vacuum to the throttle opener, then check the following. Refer to steps 1 and 2 of “Preparation”, “TCM SELF-
DIAGNOSTIC PROCEDURE (No Tools)”, AT-46.
EM
4. Read out “CLOSED THL/SW” and “W/O THRL/P-SW” depressing and releasing accelerator pedal.
Check the signal of throttle position switch is indicated properly.
LC
EC
MTBL0011
FE
CL
MT
TF
PD
AX
SU
SAT052I
BR
OK or NG
OK © GO TO 5. ST
NG © Check the following items:
I Throttle position switch RS
Refer to “Component Inspection”, AT-187.
I Harness for short or open between ignition switch and throttle position switch (Main
harness) BT
I Harness for short or open between throttle position switch and TCM (Main harness)
HA
SC
EL
IDX
AT-185
--- Page 12 ---
EXIT
CONTROL UNIT (EEP ROM)
Diagnostic Procedure
Diagnostic Procedure =NAAT0216
1 CHECK DTC
With CONSULT
1. Turn ignition switch “ON” and select “SELF DIAG RESULTS” mode for A/T with CONSULT.
2. Move selector lever to “R” position.
3. Depress accelerator pedal (Full throttle position).
4. Touch “ERASE”.
5. Turn ignition switch “OFF” position for 10 seconds.
PERFORM DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION PROCEDURE.
See previous page.
Is the “CONTROL UNIT (EEP ROM)” displayed again?
Yes © Replace TCM.
No © INSPECTION END
AT-206
--- Page 13 ---
EXIT
TROUBLE DIAGNOSES FOR SYMPTOMS
9. A/T Does Not Shift: D1 → D2 Or Does Not Kickdown: D4 → D2
9. A/T Does Not Shift: D1 → D2 Or Does Not GI
Kickdown: D4 → D2 =NAAT0081
SYMPTOM:
MA
A/T does not shift from D1 to D2 at the specified speed.
A/T does not shift from D4 to D2 when depressing accelerator
pedal fully at the specified speed. EM
1 CHECK SYMPTOM
Are “7. Vehicle Does Not Creep Forward In “D”, “2” Or “1” Position” and “8. Vehicle Cannot Be Started From D1” OK? LC
Yes or No
Yes © GO TO 2. EC
No © Go to “7. Vehicle Does Not Creep Forward In “D”, “2” Or “1” Position” and “8. Vehicle
Cannot Be Started From D1”, AT-221, 224.
FE
2 CHECK PNP SWITCH CIRCUIT
With CONSULT CL
Does “ECU INPUT SIGNALS” in Data Monitor show damage to PNP switch circuit?
Without CONSULT MT
Does self-diagnosis show damage to PNP switch circuit?
TF
PD
AX
SAT367J
Yes or No
SU
Yes © Check PNP switch circuit. Refer to “DTC P0705”, AT-102.
No © GO TO 3.
BR
3 CHECK VEHICLE SPEED SENSOR·A/T AND VEHICLE SPEED SENSOR·MTR CIRCUIT
Check vehicle speed sensor·A/T (revolution sensor) and vehicle speed sensor·MTR circuit. Refer to “DTC P0720 and ST
VEHICLE SPEED SENSOR·MTR”, AT-113, 202.
OK or NG RS
OK © GO TO 4.
NG © Repair or replace vehicle speed sensor·A/T (revolution sensor) and vehicle speed
sensor·MTR circuits.
BT
HA
SC
EL
IDX
AT-227
--- Page 14 ---
EXIT
TROUBLE DIAGNOSES FOR SYMPTOMS
21. TCM Self-diagnosis Does Not Activate (PNP, Overdrive Control and Throttle Position Switches Circuit Checks) (Cont’d)
DIAGNOSTIC PROCEDURE =NAAT0204S03
NOTE:
The diagnostic procedure includes inspections for the overdrive
control and throttle position switch circuits.
1 CHECK PNP SWITCH CIRCUIT (With CONSULT)
With CONSULT
1. Turn ignition switch to “ON” position.
(Do not start engine.)
2. Select “ECU INPUT SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT.
3. Read out “P”, “R”, “N”, “D”, “2” and “1” position switches moving selector lever to each position. Check the signal of the
selector lever position is indicated properly.
SAT761I
OK or NG
OK © GO TO 3.
NG © Check the following items: