PDF Service Manual 1994-1997 Acura Integra - 3 MB

This comprehensive service manual covers the 1994 to 1997 Acura Integra models.

It contains detailed repair procedures, specifications, and troubleshooting guides for every system in the vehicle.

Whether you're a professional mechanic or a DIY enthusiast, this manual provides the factory-approved information you need to perform any repair or maintenance task correctly.

From engine overhauls to electrical diagnostics, this guide has it all.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
INTRODUCTION

   How to Use This Manual
 This manualis dividedinto 23 sections.The first pageof each sec-
 tion is markedwith a blacktab that linesup with its corresponding
 thumb indextab on this page and the back cover. You can quickly
 tind the tirst pageof each sectionwithout lookingthrougha full ta-
 ble of contents.The svmbolsprintedat the top cornerof each page
 can also be used as a quick referencesystem.
                                                                             Specifications        trtl:{lt'
 Each section includes:
   1. A table of contents.or an explodedview index showing:
      a Partsdisassemblvsequence.
      a Bolt toroues and thread sizes.
      a Pagereferencesto descriptionsin text.
   2. Disassemblv/assembly  proceduresand tools.
                                                                             Ma i n te n a n c e   4Pi
   3. InsDection.
   4. Testing/troubleshooting.
   5. Repair.                                                                                       H
   6. Adiustments.                                                           Engine                 I-""
   SpecialInformation
  @              lnai""tes a strong possibility of sevor€ pelsonal iniury
  01 loss of life it instructions al€ not tollowed.

  CAUTION: Indicates a possibility ot personal inlury or oquipmont
  damage if instructions ale not followed.
                                                                             Fueland Emissions
                                                                                             Za
  NOTE: Gives helpful information.

  CAUTfON: Detaifeddoscriptionsot standad workshop procedures,
  salety principlosand servicaopelationsare not included Pleasonote
  that this manual conlains warnings and cautions against somo spocif-
                                                                            *Transaxle
  ic sgrvice methods which could cause PERSONALINJURY, damage
  a vehicle or make it unsafe. Pleasounderstandthat those warnings
  cannot cover all conceivablcwaYs in which service, whetheaor not
  recommended bv HONDA, might be done, or of the possibla                                           r-\
  hazardous consequences of svery conceivable way, nor could
                                                                            * S te e ri n g         l D l
  HONDA investigateall such ways. Anyone using seryice plocedures                                   \.t/
  or toofa, whethor 01 not recomondedby HONDA, ,nust sttisfY him-
   sett thoroughly that neither personal saf€ty nor v€hicle safety will
  be jaopaldized.

  All informationcontainedin this manualis basedon the latest product
  informationavailableat the time of printing.We reservethe right


                                                                                                    o
  to makechangesat any time without notice.No part of this publica-
  tion mav be reproduced,storedin retrievalsystem, or transmitted,          * Brakes
  in any Jorm by any means,electronic,mechanical,photocopying,
  recording,or otherwise,without the priorwritten permissionof the           (lncludins
                                                                                      !TEg)
  publisher.This includestest. figures and tables.


First Edition7/93     1448 pages          HONDA MOTORCO.,LTD,
All Rights Reserved                        Service Publication ottice
Specifications Apply to U.S.A. and Canada


                                                                            *Electrical            J--*
                        As sections with r includ€ SRS components.
                        special precautions are lequiled when servicing.
                                                                              (lncludins
                                                                                       ISBE)

--- Page 3 ---
SpecialTools
lndividual tool lists are located at the front of each section

--- Page 4 ---
Standardsand ServiceLimits
    Differential(Manualtransmissionl                  Section 15
                                        M€ASUREMENT                                       STANDARDINEW)                  SERVICELIMIT
 Differential         PinionshaftcontactareaLD.               81881engine 18.000- 18.016(0.7087           - 0.7093)
                                                              8 1 8 C 1e n g i n e 18.000 18.018(0.7087   - 0.7094)
                        Carrier'to-pinionclearance            81881engine 0.0r3 0.045(0.0005           - 0.0018)    o.t aron,
                                                              B18Ct engine 0.0'13       - 0.047(0.0005 0.0019)      0.1{0.006}
                        Driveshafvintermediate shaft contactarea LD.
                                                              8 1 8 8 1e n g i n e 28.000- 28.021\1.1024-1.10321
                                                              818C1engine 28.005- 28.025(1.1026 1.'1033)
                        Carrierto driveshaftclearance         81881engine 0.020- 0.062(0.0008 0.0024)
                                                              BlSC'lengine 0.045, 0.086{0.0018         - 0.0034)
                        Carrier-to-intermediate
                                              shatt clearance
                                                              B188l engine 0.050- 0.087(0.0020 0.0034)
                                                              818C1engine 0.075- 0.111(0.0030          - 0.0044)
 Differential           Eacklash                                                   0.05 0.15 (0.002  0.006)         Adjust
 prnrongear             t .D .                                                     '18.042
                                                                                         - 18.066(0.7103 0.7113)
                        PiniongeaFto-pinion  shaftclearance                        0.055- 0.095(0.0022 0.0037)      0.15{0.006)
 Sel ring-to-bearing outerraceclearance                       81881engin€ 0 - 0.10(0 0.004)                         Adjust
 Differentialtaper roller bearing preload
 StartingtorqueN.m {kgfcm,lbf.in)                             Bl8Cl engine 2.1r- 3.04{21.5       - 3 r.0,13.0-18.7) Adjust


   Differential (Automatic transmissionl                 Section 15
                                       MEASUREMENT                                  STANDAROINEWI                     SERVICELIM]T
 Difterential         Pinionshatt contactarea l.D.                           18.000- 18.018{0.7087- 0.7094)
 carfl€r              Carrier-to-oinion
                                      clearance                              0.016- 0.052{0.0006- 0.0020)        0.1{0.004)
                      Driveshafvintermediateshaft contactare l.D.            28.00s 28.025{1.1026 - 1.1033)
                      Carrier-to-driveshatt
                                         clearance                           0.025- 0.066(0.0010- 0.0026)        0.12(0.005)
 Differential         Backlash                                               0.05- 0.15(0.002- 0.006)            Adjust
 prnrongear           t.D.                                                   18.042- 18.066(0.7r03- 0.7113)
                      Piniongear-to-pinion
                                       shaftclearance                        0.059- 0.095(0.0023- 0.0037)        0.15(0.006)
 Set ring-to-bearing
                   outerraceclearance                                        0 - 0.r5(0- 0.006)                  Adjust


   Steering - Section 17
                                         MEASUREMENT                                                STANDARDINEWI
 Steeringwheel       Rotational  play at steeringwheelcircumference          0 - 10 {0 - 0.39)
                     Staninglosd at steeringwheelcircumference
                     N {kgf,lbfl                           Enginerunning     3 4\ 3 . 5 , 7 . 7 1
 Gearbox             Angle of rack-guide-screwloosenedfrom locked            20" i 5'
                     position
 Purnp               Pumppressurewith shut-offvalveclosed                    6,400 7.400165 75.920- 1.r00)
                     kPa(kgtlcm,,psi)
 Powersteering       Recommended   fluid                                     Hondapowersteeringfluid V
 tluid               Fluidcapacity               For overhaul                1 . 0 6( 1 . 1 2 , 0 . 9 8 )
                     f (USqt, lmp q0             Forfluid change             0.79(0.83,0.70)
 Power steering                with 98 N (1okgt,22lhfl
                      Deflection                                             11.5- 13.5(0.45 0.53)withusedbelt
 belt*                betweenpulleys                                         8.0- 10.010.310.39)withnew belt
                      BelttensionN lkgf,lbl)                                 390 - 540 (40- 55, 88 - 120)with used belt
                      Measuredwith belttensiongauge                          740 880175 90. 170 200)with new belt
' When usinga new belt,adjustdetlectionor tensionto new values.Runthe enginelor 5 minutesthen turn it off.
  Readiustdetlectionor tensionto usedbeltvalues.

--- Page 5 ---
Engine
E n g i n eR e m o v a l / l n s t a l l a t i o. .n. ' ' . . . . . . . .5 - 1
C y l i n d e rH e a d / V a l v eT r a i n . . ' . . . . . . . . . . . .6 - 1
EngineBlock....             ......7-1
EngineLubrication        .........8-1
                    System ...... 9-1
IntakeManifold/Exhaust
Cooling                    .......1O-1

--- Page 6 ---
EngineRemoval/lnstallation
        (cont'dl

       4.   Tightenthe mount bolt on the side enginemount.       6.     Installthe right front mount/bracket,then tighten the
                                                                        bolts in the numberedsequenceas shown (O-@).

                                                                 A/T:                                      ' 1 . 2 5m m


 m'
.tE                                                                                                 @ 10 x
                                                                                                      44 N.m (4.5 kgt'm,
                                                                                                      33 tbt.fr)


                          12 x 1.25mm
                          74 N.m (7.5 kgf.m,
                          54 lbt.ttl


                                                                           O 12 x 1.25mm
                                                                             64 N.m 16.5 kgt.m,47 lbf.ftl
                                                                             Replace.

       5.   Installthe rearmount bracket,then tightenthe bolts
            in the numberedsequenceas shown {@ @).
                                                                 M/T:
                                                                                                    ' 1 0x 1 . 2 5 m m
                                                                                                @
                                                                                                    44 N-m (4.5 kgf.m,

              @ 12 x 1.25mm
                59 N.m {6.0 kgf'm, 43 lbl'It)
                Replace.


                                         12 r 1.25mm
                                         59 .m 16.0 kgl.m,
                                                                 O 1 2 x 1 . 2 5m m
                                                                   83 N'm (8.5 kgf.m,61 lbt.frl

--- Page 7 ---
Timing Belt
      Removal
     NOTE:                                                      4,   Loosenthe adjusting nut and mounting nut, then
     . Turn the crankshaftpulley so the No. 1 piston is at           removethe alt€rnatorbelt.
       top d6ad center (TDC)before removing the belt (see
       page&12).                                                                                    ADJUSNNGNUT
                                                                                                    8 x 1.25mrr
     a Inspectthe water pump when removed the timing                                                2a N.m l2.a lef.m,
       bolt {see page 10-9}.                                                                        17 rbl.ftl

     1.    Removethawhe€lwellsplashshield(seepage6-18).

     2.    Loosen ths adjusting bolt and mounting bolts, then
           remove the power steering {P/S)pump belt.

                                            AA,USNNG


                                                                         MOUNTINGNUT
                                                                         10x 1.25mm                     EELT
                                                                         a,lN.m{4.5kgl.m,33lbfftl
          MOUivNNGBOLTS
          8 x 1.25mm
          2aN.m12.4kgf.m,17 lbtfrl                                   Removethe cruisecontrolactuator(seepage6-18).

          Loosenthe adjustingbolt and idler pulley bracket           Removethe sid6snginemount.
          bolt, then remove the air conditioning(A,/C)com-             10x 1.25mm
          oressorbelt.                                                 52N.m{5.3kgr'm,38lbtft}
                                                                        Replace.

I                      ADJUSTING


          IDLERPUI.IEYBRACKET
          BOLT
          l0 r 1.25mm
          a/aN.m{1.5kgf.m.33lbf'ft}


                                                                                                    12 x 1.25mm
                                                                                                    74 N.m 17.5kgt m,
                                                                                                    s4 tb{.ftl

--- Page 8 ---
Replacement
1. As illustrated in the removal steps of this proce-                                  4.   Working from the camshaft side. use the driver and
   dure, use a commercially-available                air-impactdriv-                        an air hammerto drive the guide about 2 mm {0.1
   er attachmentmodified to fit the diameter of the                                         i n ) t o w a r d s t h e c o m b u s t i o nc h a m b e r .T h i s w i l l
   valve guides. In most cases.tho same procedure                                           knock oft some of the carbon and make removal
   c a n b e d o n e u s i n g t h e V a l v e G u i d e D r i v e ra n d a                 eaSrer.
   conventionalhammer.
                                                                                            GAUTIOiI:
                                                                                            o Alwrys woar safety goggles or a face shiold
               COMMERCIALLYAVAILABI,I                                                         wh6n using tho Eir hammer.
               VALVEGUIDEDRIVER                                                             . Hold ths air hammsr directly in lins with the
                                                                                              vrlvr guidc to prsvont damaging tho drivor.

                                                                                            Turn the head over and drive the guide out towatd
                                                                  -----T_-                  the camshaftside of head.

                                                  sz--                   l r l
                                      f |          12.21i^l              11.3mm
                                                                                            lf a valveguide still won't move,drill it out with a 8
                                                                         lo.il,l in)        mm (5/16in) bit,then try again.

                     RGmov.lrnd In3tlllation                                                CAUTION: Drill guid$ only in oxtremo cases:You
                     VALVEGUIDEDRIVER,    6.6mm                                             could drmrgo tho cylinder hosd if ths guido br"akr.
                     0?942- 6570100


     S e l e c tt h e p r o p e r r e p l a c e m e n tg u i d e s a n d c h i l l
     t h e m i n t h e f r e e z e rs e c t i o no f a r e f r i g e r a t o rf o r
     aboutan hour.

      Use a hot plate or oven to evenly heat the cylinder
      headto 300'F(150'Cl.Monitorthe temperaturewith
      a cookingthermometer.


                                                                                            VALVEGUIDEDRIVER,6.6mm
                                                                                            07942 - 65701q)


                                                                                                                          ",
      CAUTION:                                                                                                   OO
                                                                                                                         O (V /rl    -1-- ) o
      . Do not use a torch; it may warP the hgad.
      . Do not get ths head hottq than 3OO'F1150"C);
        excessivehgat may loos€n thGvalvs soat3.
      . To avoid burns, usa hoavy glov93whon handling
        the heated cylinder hoad.
                                                                                             Removethe new guide{s}from the refrigerator,
                                                                                                                                       one
                                                                                             at a time, as you needthem.
                                                                                                                                    {cont'd)


                                                                                                                                                             6-25

--- Page 9 ---
VTEC
               Flowchart VTECPressureSwitch (cont'dl
 Troubleshooting
    u
             lFrom pag6 6-39)


                                                                                        OOMMERCIALLYAVAILABII
  D i s c o n n s c tl h e 1 P c o n n e c t o r                                        OIL PRESSURE
                                                                                                   GAUGE
  trom the VTECsol6noidvalve.


  Attach the battery positivo tormi
  nal to the GRN/WHTterminal.


  Startthe engineand chgckoil
  pressureat 5,000rpm (lor VTEC
  oil pr€ssure
             test).


                                                                                                     GAUGE JOIMf ADAPIOR
                                                                                                     SNAPON MT2S1'
                                                                                                     1 0 x 1 . 0m m
                                                                                                     . Use new washer when
                                                                                                       installingth6 soalingbolt.
                             NOTE:
                             Keep moasuringtim6 as shon 6s possi-
                             ble becauseenginei5 runningwith no
                             load lless than ono minuto).


      ls pressureabove 400 kPa
      (4kgt/cm,,60 psi)?                             In.p.ct th. VIEC .olrnoid v.lv..


  Checktor continuity betwe6n the
  2 terminsls on th€ VTECprsssure
  switch !nder above condition.


  Sub.titut. . klown-eood ECM
  and rachack.|f aymplom/indica-
  tion goaa away rrplaca th. o?igi-
  n.l ECM.

--- Page 10 ---
NOTE:Cleanthe headoil controlorificeand the rockershaftorificeswhen installino.


                                           ROCKEBARM ASSEMBLY


  CYLINDERHEAD
  BOLTS
  1 1x 1 . 5m m                                          INTAKEVALVESPRINGINNER
  81 N m (8.3ks{ m, 60
  Apply clean engine oil
  to threads and washer
  contact surface.                                                  SPRINGRETAINER

                                                                    INTAKEVALVESPRINGOUTER


  VALVE                    SPRINGSEAT                                 VALVESEAL
                                                                      Replace.

                                                                       SPRINGSEAT
                                                                        VALVEGUIDE
  SPRINGRETAINER
                                                                     MOTION
   EXI{AUSTVAL                                                   ASSEMBLY              INTAKEVALVE
   SPRING
       VALVESEAL
       Replace.
                                                                                       INTAKE ROCKER
      VALVE                                                                                  ORIFICE
                                                                                       Clean.
      LOSTMOTION
      ASSEMBLY

                                                                                       ROCKERSHAFT
                                                     DOWEL
   EXHAUSTVAL                                        PIN -,
                                                           ROCKER
                           OOWEL                    SHAFTORIFICE
                           PIN


CYLINDERHEAO
GASKET
13LAYEBSOF MET
Replace.
                                                                                   SEALINGBOLTS,20 mm
                                                                                   64 N.m 16.5kgf.m,47 lbtftl

--- Page 11 ---
Valves,ValveSpringsand ValveSeals
  Removal(cont'dl
 3.   Installthespecialtoolas shown   Valve Dimensions


          COMMERCIALLY    AVAILABLE
          VALVEGUIDESEALREMOVER
          Lrst"EP/N s79(x'OR KD3350


                                      lntrko ValYo
                                      A Standsrd (N.wl: ilil.go - *t.10 mm
                                                        (1.295- 1.303inl
                                      B Standard (Newl: 101.00- 101.30mm
                                                        (3.976- 3.988inl
                                      C Standard (N.w): 5.a75- 5.185mm
                                                        (0.2156- 0.2159inl
                                      C Sorvicc Limit   5.i!15(0.21.lt in)
                                      D Standard (Ncw): 1.05- 1.35mm
 4.   Removethe valveguide seal.                        (0.04i - 0.05:tin)
                                      D Sorvicc Limh:   0.85 mm (0.033inl

                                      Exhau3tValve
                                      A Stand.rd (Ncwl 27.90- 28.10mm
                                                        11.098- 1.106inl
                                      B Standard (Ncwl: 1qr.6lt- loo.glt mm
                                                        (3.961- 3.972inl
                                      C St.nd.rd (Now| 5./L51,
                                                             - 5.460mm
                                                        (0.2146- 0.215|,inl
                                      C ServicoLimit:   5.a20(0.2134inl
                                      D Standsrd lNewl: 1.65- 1.95mm
                                                        {0.065- 0.077inl
                                      D Sorvicc Limit   1.45mm (0.057inl


6-68

--- Page 12 ---
lllustrated Index

 NOTE:                                                                                           Lubricateall internalpartswith engineoil during
 . Apply liquidgasketto the matingsurfacesof the right                                           reassemory.
   s i d e c o v e r a n d o i l p u m p h o u s i n gb e f o r ei n s t a l l i n g
   them.
                                                   - 0001.
 . U s el i q u i dg a s k e tP, a n N o . 0 8 7 1 8                                                    6x1.0mm
 . C l e a nt h e o i l p a n g a s k e t m a t i n g s u r f a c e sb e f o r e                        12 N.m (1.2kgf.m,I lbf.ftl
   installingit.                                                                       OIL PAN

 Bl8Bl engine:                                                        wAsHEF
                                       DRAINPLUG
                                       44 N.m {4.5kgf.m,                                                                   6x1.0mm
                                       33 tbtfr)                                                                           11 N.m (1.1kgf.m,8lbtft)


                                    GASKET
                                    Replace.


                                6x1.0mm                                                                    OIL SCREEN
                                1'l N.m {1.1kgt.m, I lbtft)

     12 x 1.0mm
     103N.m (10.5kgf.m,?6lbf ft)
                                                                                                                             11 x 1.25mm
                                                                                                                             76 N.m
                                                                                                                             17.8kgl.m, 56 lbf ftl
 MANUAL                                                                                                                      Applyengineoilto the bolt
 FLYWHEEL                                                                                                                    threadsand the washers.
                                                                                                                             NOTE: After torquing
 '12x 1.0mm                                                                                                GASKET            each cap, turn crankshaft
                                                                                                           Replace.          to checklor binding.
 74 N.m {7.5kgt m,54lbf.ftl                             WASHER
 Torquesequence,  page7 7
                                                                                                      BEARINGCAP            CRANKSHAFT
                                                                                                                            End play,page7-12
                                                                                                                            Runout,Taper,and
 AUTOMATICTRANSMISSION                                                                                                      Out-of-Round, pages7 12,13
 DRIVE PLATE                                                                                                                           page7 22
                                                                                                                            Instsllation,
 Checkfor cracks,
                                                                                                                           MAIN BEARING
                                                      6x1.0mm                                                              Radialclearance,page7-8
                 Apply liquidgasket                   11 N.m {1.1kgl.m,                                                             page7-8
                                                                                                                           Sel€ction,
                 to blockmatingsurface.               8 tbf.frt                                                            NOTE:New main bearings
                                                                                                                           must be selectedby matching
     OIL SEAL                                                                                                              crankand blockidentification
                page7-25,
     Installation,                                                                                                         markrngs.


                      RIGHT
                      SIDECOVER
                                                                                                          DOWELPINS
                                                                                                                              OIL PUMP
                   THRUSTWASHERS                                                                                              Overhaul,page 8-9
                   Groovedsidesfaceoutward.
                   NOTE:Thrustwasherthickness
                   is tixedand must not be changed
                   by grindingor shamming.

                                                                                                                                     8 x 1.25 mm
                                                                                                                                     2,1N.m {2.4kgt m,
                                                                                                                                     17 tbt.ft)
                                                                                       O.RING                              OIL SEAL
                                                                                       Applyengrne                                    page8-11
                                                                                                                           Installation,
                                                                                       orl.
                                                                                       Replace.
                                                                                                             6x1.0mm
                                                                                          Apply liquidgasket '11N.m {1.1kgf'm, 8 lbl ft)
                                                                                          to blockmating                                        (conr'dl


                                                                                                                                                   7-3

--- Page 13 ---
I

    '1.
           Using a piston, push a new ring into the cylinder                          After installinga new set of rings, measurethe ring-to-
           bore 15- 20 mm (0.6 0.8 in) from the boftom.                               gfoove clearances:

          M e a s u r et h e p i s t o n r i n g e n d - g a pw i t h a f e e l e r   Top Ring Cl€arance:
          gauge:                                                                      Standard lNewl: 0.045- 0.070mm
                                                                                                      10.0018- 0.0028in)
             lf the gap is too small.checkto see if you have                          ServiceLimit: 0.13mm {0.005inl
             the properringsfor your engine.
                                                                                      SecondRing Clearance:
             lf the gap is too large,recheckthe cylinderbore                          Standard {Newl: 0.040- 0.065mm
             diameteragainstthe wear limits on page7-13.                                              (0.0015- 0.0026inl'1
             ll the bore is over the servicelimit, the cylinder                                       0.0i15- 0.070mm
             blockmust be rebored.                                                                    (0.0018 - 0.0028in)',
                                                                                      ServiceLimit: 0.13 mm (0.005inl
          Piston Ring End-cap:
          Top Ring
          Standard (New): 0.20- 0.35 mm
                          (0.008- 0.01'linl'1
                          0.20- 0.30 mm
                          10.008- 0.012inl''
          ServicaLimit: 0.60 mm (0.024in)
          Second Ring
          Standard (Now): 0.40- 0.55 mm
                          10.016- 0.022in)
          ServiceLimit: 0.70 mm (0.028in)
          Oil Ring
          Standard (New): 0.20- 0.50 mm
                          (0.008- 0.020in)'1
                         0.20- 0.,15mm
                         {0.008- 0.018inl',
          ServicaLimit: 0.70 mm 10.028in)


                                       iliiii
                                 .--r.llli.j---.-
    PISTONNING


                                  ioi
                        ---'z            ll
                         ENDGAP-11--
     RIKENmanufactured               pistonring                                        RIKENmanufacturedpistonring
     T E I K O K UP I S T O NR I N Gm a n u f a c t u r e do i s t o n r i n q         T E I K O K UP I S T O NR I N Gm a n u f a c t u r e dD i s t o nr i n o
     { 8 1 8 8 1e n g i n eo n l y )                                                   ( B ' 1 8 8e1n g i n eo n l y )


                                                                                                                                                    7-17

--- Page 14 ---
EngineOil
  lnspection                                                 Replacement

     Check engine oil with the engine off and ths cal       CAUTION: Remova tho drain plug cal€fully whilo the
     parked on level ground,                                ongine is hot; the hot oil may cause scalding.

     Make cenain that the oil levelindicatedon the dip-     1. Warm up the engine.
     stick is between the upper and lower marks.
                                                            2,    Drainthe engineoil.
 3 . lf the l€vel has droppedclose to the lower mark, add
     oil until it reachesthe upper mark.

     CAUTION: Inssrt lho dipstick carotully to avoid
     bending it.


                                                            3.     Reinslallthedrainplugwith a new washer,and refill
                                                                   with the recommendedoil.

                                                                   CAUTION: Do not ovortighton tho drain plug.

View the complete manual on HeyDownloads →