PDF Repair Manual Wacker Neuson BPU 2440 BPU 2950 Vibroplate - 356 KB

Keep your Wacker Neuson vibratory plates running efficiently with this official repair manual for the BPU 2440 and BPU 2950 models.

The guide offers detailed service information, troubleshooting steps, and repair procedures.

Written for technicians, it provides the necessary knowledge to diagnose and fix common issues, ensuring minimal downtime for your compaction equipment.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
www.wackergroup.com


                                   0078232   004
                                   0603      en


                             Vibroplate

                             BPU 2440
                             BPU 2950


REPAIR MANUAL


 0   0   7   8   2   3   2

--- Page 3 ---
Safety Information                               BPU 2440/2950 Repair
 Label                           Meaning
                                 WARNING!
                                 To prevent hearing loss, wear hearing protec-
                                 tion when operating this machine.


                   wc_gr001475


                                 A nameplate listing the Model Number, Item
                                 Number, Revision, and Serial Number is
                                 attached to each unit. Please record the infor-
                                 mation found on this plate so it will be avail-
                                 able should the nameplate become lost or
                                 damaged. When ordering parts or requesting
                                 service information, you will always be asked
                                 to specify the model, item number, revision
                                 number, and serial number of the unit.


wc_si000099gb.fm                  8

--- Page 4 ---
BPU 2440/2950 Repair                                                      General Information
      3.12 To Start

                   See graphic: wc_gr000014
                   3.12.1   Open fuel valve by moving lever to the right (a1).
                            Note: If engine is cold, move choke lever to close position (b1). If
                            engine is hot, set choke to open position (b2 ).
                   3.12.2   Turn engine switch to “ON” (e1).
                   3.12.3   Open throttle by moving it slightly to left (d1).
                   3.12.4   Pull starter rope (c).
                            Note: If the oil level in the engine is low, the engine will not start. If this
                            happens, add oil to engine. Some engines are equipped with an oil
                            alert light (f) that will come on while pulling the starter rope.
                   3.12.5   Open choke as engine warms (b2).
                   3.12.6   Open throttle fully to operate.


      3.13 To Stop

                   See Graphic: wc_gr000014
                   3.13.1   Reduce engine RPM to idle by moving throttle completely to right (d2).
                   3.13.2   Turn engine switch to “OFF” (e2).
                   3.13.3   Close fuel valve by moving lever to the left (a2).


wc_tx000264gb.fm                                     19

--- Page 5 ---
Repair Procedures                                                BPU 2440/2950 Repair
5.     Repair Procedures

       5.1         General Repair

                         The repair procedures specify using sealants and screw and nut
                         adhesives to seal metal surfaces and secure fasteners in place. These
                         products must be used where indicated.

                         Although Loctite is referred to throughout this manual, an equivalent
                         sealant such as Hernon or Omnifit may be used. When using sealants,
                         always follow the application instructions on the container. Refer to the
                         thread locking and sealant chart located in this manual.

                         Most thread locking sealants break down at temperatures above
                         350°F (177°C). If a bolt or nut resists separation, apply heat to it using
                         a small propane torch. When doing so, check to make sure no other
                         portion of the unit will be damaged from the use of the torch.

                         Correct torque values are listed whenever possible. Follow these
                         specifications when replacing or tightening screws and nuts. This is
                         especially important at sealed surfaces where screws must be
                         tightened evenly to ensure airtight seals thus preventing leaks.

                         The step-by-step procedures listed here provide complete descriptions
                         for the removal and replacement of all serviceable parts. However,
                         items such as bearings and shafts, assembled with press fits, should
                         be inspected for wear and damage while still in place. Removing or
                         installing such items often requires tools or presses to do the task
                         properly.

                         When installing bearings into housing, apply pressure only to the outer
                         race of the bearing. If pressing a bearing onto a shaft, pressure should
                         be applied only to the inner race. Apply pressure evenly around the
                         bearing. Avoid using a hammer to pound bearings in place.

                         If using heat to fit a bearing onto a race, use a hot plate or hot oil bath
                         where the temperature can be controlled. Never heat a bearing using
                         a propane torch. Excessive heat, over 350°F (150°C), can affect the
                         hardness characteristics and tolerance values of the bearing.


wc_tx000329gb.fm                                 30

--- Page 6 ---
BPU 2440/2950 Repair                                                 Repair Procedures

                        a
                                                                                 d
              b


                                          c
                                                                                     wc_gr001447

                                     wc_gr001446


                       Ref.   Note
                        a.    Drive shaft side machined surface
                        b.    Pulley end of housing
                        c.    Piston end of housing
                        d.    Use flanged covers to position bearings the cor-
                              rect distance into exciter housing.


                   Procedure continued on next page.


wc_tx000329gb.fm                                   41

View the complete manual on HeyDownloads →