PDF Repair Manual Manitou MLT 634-120D Telehandler - 5 MB
This is the official repair manual for the Manitou MLT 634-120D ST4 S1 Telehandler.
It provides service technicians with complete, step-by-step instructions for all repair and maintenance procedures.
The manual covers everything from the engine and transmission to the hydraulic and electrical systems.
Detailed diagrams and specifications ensure every job is done correctly and to factory standards.
PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
PDF viewer loading area
Text Preview from This Manual
The text below was extracted from the visible preview pages to help you confirm the manual contents before download.
--- Page 1 ---
GENUINE PARTS CATALOGUE
CATALOGUE PIECES DβORIGINE
ORIGINAL ERSATZTEILKATALOG
CATALOGO DE PIEZAS LEGITIMAS
CATALOGO RICAMBI ORIGINALI
This document has been printed from my e doc
MANITOU BF
Head office: 430, Rue de lβAubiniΓ¨re
44150 Ancenis - FRANCE
Share capital: 39,548,949 euros
857 802 508 RCS Nantes
Tel: +33 (0)2 40 09 10 11
www.manitou.com
--- Page 3 ---
00
GENERAL CHARACTERISTICS AND SAFETY
- GENERAL INSTRUCTIONS AND SAFETY
NOTICE
- GENERAL CHARACTERISTICS AND
SPECIFICATIONS
- GENERAL LOCATION
- GENERAL CONTROL AND ADJUSTMENT
--- Page 4 ---
00
GENERAL LOCATION
pages
LOCATION OF NAME AND IDENTIFICATION PLATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
(05/06/2015) 00-03-M247EN
--- Page 5 ---
ENGINE CIRCUITS FLOW DIAGRAM 3
LUBRICATION CIRCUIT
The oil pressure and volume flow rate ensure lubrication of the engine and also, to a large extent, engine
cooling. The pressure relief valve opens at 9 bar and the maximum oil temperature in the sump is 125Β°C.
10
Key:
1 - Oil sump 9 - Camshaft bearing
2 - Oil pump 10 - Crankshaft bearing
3 - Pressure relief valve 11 - Piston cooling nozzle
4 - Oil cooler 12 - Rocker arm
5 - By-pass valve 13 - Hydraulic tappets
6 - Pressure control valve 14 - Turbocompressor
7 - Oil filter 15 - Air compressor (optional)
8 - Main oil gallery
12
14
15
11
8
13
5
4
9
7
10
6 3 2
1
4
7
6
2
3 6
8
(05/06/2015) 10-02-M247EN
--- Page 6 ---
ENGINE COMPONENTS LOCATION 7
FUEL INJECTION CIRCUIT
Key:
1 - Low pressure fuel supply 7 - Pressure Relief Valve (PRV)
10
2 - High pressure pump 8 - PRV return
3 - MPROP (magnetic proportional valve) 9 - Injector electrical connector
4 - FCU (Fuel Control Unit) return 10 - High pressure fuel supply
5 - High pressure fuel rail 11 - Injector return
6 - High pressure fuel line pressure sensor
Red circuit = 350 - 1800 bar
Green circuit = low pressure return
6
8
5 7
2
(25/02/2015) 10-03-M247EN
--- Page 7 ---
ENGINE CONTROL AND ADJUSTMENT 7
H β FIXED ENGINE COVER REMOVAL
ο Carry out the "MOVABLE ENGINE COVER REMOVAL"
10
1 1 operation e A
2
Remove the 2 screws from the exhaust guard (Item1).
Remove the screws (Item 2).
Remove the 4 screws (Item 3).
2
3 3
3
3
I β EXHAUST REMOVAL / REFIT
ο Carry out the "MOVABLE ENGINE COVER REMOVAL"
operation e A
1 Unscrew the DOC inlet clamp (Item 1).
Unscrew the DOC outlet clamp (Item 2).
2
(16/02/2015) 10-04-M247EN
--- Page 8 ---
ENGINE CONTROL AND ADJUSTMENT 17
2
R β TURBO REMOVAL
3
4 Loosen the exhaust pipe hose clamp (Item 1) of move the hose
to one side.
10
Loosen the turbo side air inlet hose clamp (Item 2), plug the
turbo inlet port.
1
Loosen the turbo air outlet hose clamp (Item 1) and insert a
plug (Item 4).
l 647549 (Deutz TCD/TC 3.6 L4 engine-EU level IV /
US EPA Tier 4) - Turbocompressor Removal - Refit
S β ENGINE SHOCK ABSORBER REMOVAL
Remove the transmission universal joint.
Unscrew the screws (Item 1, Item 2 and Item 3) in that order to
change the shock absorber components:
C - Damper D - Seal E - Bush
Tightening torque:
Screw no. 1: 35 N.m, 5/16-25
Screw no. 2 : 35 N.m with medium thread lock
Screw no. 3: 35 N.m with medium thread lock
3
2
B
A
C
1
(16/02/2015) 10-04-M247EN
--- Page 9 ---
ENGINE REMOVAL 3
2 C β HEATING CIRCUIT
Disconnect the lower hose (Item 1).
Disconnect the upper hose (Item 2).
10
3 Disconnect the engine water filling hose (Item 3).
1
Near to the boom, remove the strut, 2 screws.
D β DIESEL FUEL CIRCUIT
4
On the diesel filter support bracket, disconnect the engine
1
2 supply hose (Item 1), plug the opening on the filter, remove
3 the 2 screws (Item 2) and tilt the diesel filter / support bracket
assembly backwards (Item 3).
Disconnect the fuel return hose (Item 4).
Disconnect the water presence connector X178 and clogging
connector X166A and X166B (Item 4).
X178
3 Undo the clamp (Item 1) securing the engine oil dipstick tube
(Item 2) and remove the dipstick.
2
Disconnect the water presence connector X178 and clogging
1
connector X166A and X166B (Item 3).
E β ELECTRICITY
Disconnect the engine connector X277 (Deutz/Manitou wiring
1 harness connection).
Disconnect the pre-heating cable harness (Item 1) X167.
(05/06/2015) 10-06-M247EN
--- Page 10 ---
10
SPECIFIC ENGINE TOOLING
pages
FAN BELT FITTING TOOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
ELECTRONIC TENSION METER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
ADDITIONAL ENGINE TOOLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
(19/03/2015) 10-09-M247EN
--- Page 11 ---
TRANSMISSION CONTROL AND ADJUSTMENT
20
pages
TIGHTENING TORQUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
β MECHANICAL TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
(19/03/2015) 20-04-M247EN
--- Page 12 ---
SPECIFIC TRANSMISSION TOOLING
20
pages
BASIC MANOMETER SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
DIGITAL MANOMETER SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
GEAR BOX REMOVAL TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
(20/03/2015) 20-09-M247EN
--- Page 13 ---
BRAKE CHARACTERISTICS AND SPECIFICATIONS
pages
40
SERVICE BRAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
PARKING BRAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
(20/03/2015) 40-01-M247EN
--- Page 14 ---
BRAKE CONTROL AND ADJUSTMENT 5
PARKING BRAKE
CONTROL AND ADJUSTMENT
1
A
B
For public highway certified (HRT) lift trucks
40
β Place the lift truck on level ground with the rated load in the transport position.
β Check braking by locking the parking brake (Item 1) in position A.
β Pull on the lift truck rear towing pin with a minimum force of 3500 daN. The wheels of the lift truck
must not rotate.
β Carry out adjustments if necessary:
- Progressively tighten the end of the lever (Item 1) and recheck braking.
- Repeat the operation until the correct braking adjustment is obtained.
For non HRT certified lift trucks
β Place the lift truck on a slope of at least 15 % with the rated load in the transport position.
β Check braking by locking the parking brake (Item 1) in position A.
β The adjustment is correct when the lift truck remains stationary on the slope.
β Carry out adjustments if necessary:
- Depress the service brake pedal, unblock and release the parking brake (Item 1) in position B.
- Progressively tighten the end of the lever (Item 1) and recheck braking.
- Repeat the operation until the correct braking adjustment is obtained.
(23/03/2015) 40-04-M247EN
--- Page 15 ---
BOOM COMPONENTS LOCATION
pages
LOCATION OF THE DUPLEX BOOM MAIN COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
50
(24/03/2015) 50-03-M247EN
--- Page 16 ---
HYDRAULICS
- HYDRAULIC CHARACTERISTICS AND
SPECIFICATIONS
- HYDRAULIC SCHEMATIC DIAGRAMS
- HYDRAULIC COMPONENTS LOCATION
- HYDRAULIC CONTROL AND ADJUSTMENT
- HYDRAULIC COMPONENTS REMOVAL
- HYDRAULIC SPECIFIC TOOLING
70
--- Page 17 ---
HYDRAULIC CHARACTERISTICS AND
SPECIFICATIONS 1
MASTER CYLINDER WITH ASSISTANCE
Values for information purposes only.
1 - Part :
- To send the pressure fluid in order to push the brake
pistion that will stop the wheels.
- To add the mechanical force (pedal) and the hydraulic
force in order to help the driver.
2 - Description :
P L N
B R
R 70
N L B
P- Assistance pressure
L- Pilot pressure (LS line)
N- Return to the tank line
B- Brake pressure
R- LHM tank
P
Notes : ____________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
(06/10/2013) F70-3-0027EN
--- Page 18 ---
HYDRAULIC SPECIFICATIONS AND
CHARACTERISTICS 3
b B5 A5
VRP
b
β The hydraulic pressure arrives at the entry module with pump
T B stand-by pressure.
EL β The Pressure balance ensures communication between the main
a pressure line through the valveblock to the receiver feed.
Electro-hydraulic controller
(βRestβ state) β It takes the receiver pressure and communicates it to the pump.
β There is a priority between the receiver feed and pressure
b B5 A5 information transmission to avoid any rapid pressure increase
as a result of a delay in slide opening relative to pump control.
70
VRP
b
T B
EL
a
Electro-hydraulic controller
(Setting βbβ)
(09/10/2012) F70-3-0040EN
--- Page 19 ---
HYDRAULIC SCHEMATIC DIAGRAMS 3
KEY
Position on
Item Designation Characteristics
diagram
AC Accumulator O27, G36
BA Accumulator unit K39
BRVI Fan reverse control unit K10
Y42: Fan direction reversal EV
Y43: Fan control EV
CA Suction strainer S16 125 ΞΌm absolute
CSP Counterbalance valve I31
CR (O) Trailer hook (option) C17, C19, C26
D Distributor Q39
EA Attachment element Q33
a (Y18): Neg. direction proportional EV
b (Y17): Pos. direction proportional EV
EA (O) Attachment element (option) Q29
EE Inlet element Q25
Y20 : hydraulic cut-off EV (VS - safety valve)
EF Closing element Q38
EI Tilting element Q27
EL Lifting element Q35
b (Y19): Lowering proportional EV
ET Telescope element Q31
EVAA (O) Rear attachment electrovalve (option) C16, C18, C21, C23
EVP (O) Pilot electrovalve (option) Q22
EVTDF (O) Telescope head electrovalve (option) C37, C39
EV (S1) Electrovalve (solenoid 1) G35
EV (S2) Electrovalve (solenoid 2) I32
FDAV Front disc brake I2
FDAR Rear disc brake I22
70
FEMS EMS head filter M39
FR Return filter Q18 15 ΞΌm absolute
M Engine I17 o 10 - ENGINE
MA Manipulator O2,O40
MC Master cylinder A3
N Level S11
REAR OPTION-1 Single-acting option (rear attachment plug) C28
REAR OPTION-2 Double-acting option (rear attachment plug) C27
REAR OPTION-3 Hydraulic hook option (rear attachment plug) C25
REAR OPTION-4 Double + single rear predisposition option (rear attachment plug) A23
REAR OPTION-5 2 double rear predispositions option (rear attachment plug) A20
REAR OPTION-6 Towing hook + double rear predisposition option (rear attachment plug) A18
REAR OPTION-7 Towing hook + single rear predisposition option (rear attachment plug) A15
FRONT OPTION-1 Hydraulic locking option (front attachment connector) C33
FRONT OPTION-2 Telescope head electrovalve option (front attachment connector) C36
FRONT OPTION-3 Telescope head electrovalve and hydraulic locking option A38
(front attachment connector)
P Hydraulic pump G13
PCR Cooling circuit pump K15
PD Steering pump C10
PFR Trailer brake connector integrated in the VAFR E4
PP Pressure test port O25
PRES Pressure switch E12
PRES (O) Pressure sensitive switch (option) G34
PRF (O) Leakage return connector (option) O37, O39, O 40
R Hydraulic tank S11 Capacity 135 β
Average level 110 β
Steering reserve 12 β
(27/03/2015) 70-02-M247EN
--- Page 21 ---
HYDRAULIC CONTROL AND ADJUSTMENT 3
JSM
SPU
70
Distributor SX14S
(31/03/2015) 70-04-M247EN
--- Page 22 ---
HYDRAULIC CONTROL AND ADJUSTMENT 13
100 N.m
12
42
N.m
T3
13
9
6
7 60 N.m
30-35 N.m
10 N.m 30-35 N.m 8
100 N.m 10 10 N.m
5
11
20 N.m 5 N.m
1 N.m
10 N.m 5 N.m
Loctite 542
4 10 N.m
1 45 N.m
20 N.m
3 20 N.m
Loctite 542
45 N.m 3,5 N.m
Β± 6 N.m Β± 0,5 N.m
2
1 - Relief valve 8 - Hydraulic control unit
70
2 - Flow regulator 9 - Return spring housing
3 - DLS/LS Selector 10 - EMS module control piston
4 - Priority valve seat 11 - EMS module
5 - Priority valve plug 12 - Flushing valve plug
6 - Anti-shock valve 13 - Tie-bolt nuts
7 - Balance plug
(31/03/2015) 70-04-M247EN
--- Page 23 ---
HYDRAULIC COMPONENTS REMOVAL 5
Remove the screws (Item 27)
and tilt the SPU support
forward (Item 28).
28
27
(According to option), remove the cab hydraulic hook cable
(Item 29)
30 30 (According to option) Disconnect the two or three connectors
30
X28, X35, (X92) (Item 30)
b
31
31
Locate their positions to ensure they are correctly
31 31
31 reconnected
(According to option) Disconnect the four or five control hoses
29
(Item 31) from the upper part of the distributor.
b Locate their positions to ensure they are correctly
reconnected
Disconnect the safety valve connector (X23) (Item 32)
70
32
33 Remove the screw securing the distributor support bracket to
33
the frame (Item 33)
33
(31/03/2015) 70-06-M247EN
--- Page 24 ---
ELECTRICITY
- ELECTRICAL CHARACTERISTICS AND
SPECIFICATIONS
- ELECTRICAL SCHEMATIC DIAGRAMS
- ELECTRICAL COMPONENTS LOCATION
- ELECTRICAL CONTROL AND ADJUSTMENT
- ELECTRICAL COMPONENTS REMOVAL
- ELECTRICAL TROUBLESHOOTING
- ELECTRICAL SPECIFIC TOOLING
80
--- Page 25 ---
ELECTRICAL CHARACTERISTICS AND
SPECIFICATIONS 9
Item Diagram Item Diagram
1
X71
1
2
2 X87
3
4 8
X72A
7
X72B 6
X73A 5
X73B
X74
X75
X87 1
2
Distributor 3
X76A 4 8
7
6
5
X76B
X89
2 1
1 4 3
3 X90 6
X77
6
5 X91
4
X92
1
X78
2 X93 2
1
2
1
4
2 X95
X79 3 1
7 3
4 8
80