PDF Parts Manual Leeboy 7000 Conveyor Paver - 858 KB
This is the official parts manual for the Leeboy 7000 conveyor paver.
It includes detailed exploded views and a complete list of part numbers for every component of the machine.
This guide is essential for accurately ordering replacement parts and minimizing downtime during paving season.
It's an indispensable resource for mechanics and parts managers.
PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
PDF viewer loading area
Text Preview from This Manual
The text below was extracted from the visible preview pages to help you confirm the manual contents before download.
--- Page 1 ---
PARTS MANUAL
7000 Conveyor Paver
Manual No. 7000102
--- Page 3 ---
~B
~....--F ......- - -
21 20 19 18 1752'53
45 43 VIEW IN' DIRECTION OF ARROW A ...- - - - - -....
~ 26
25
.. . ....
VIEW IN ~OX C VIEW IN BOX D
VIEW IN BOX F
6
--- Page 4 ---
LOADING AND UNLOADING NOTE
A man should always be on the ground to assist the
GENERAL operator in the unloading function.
Trailers used to haul the paver should have ample
capacity to carry the weight of the paver. Place the trailer
in a clear, level area for loading or unloading. . ! CAUTION!
DO NOT LETTHE SCREED STRIKE THE RAMP WHEN
Work slowly and carefully to avoid accidents. Keep the MOVING OFF THE RAMP. THIS CAN BREAK THE
area clear. BEARINGS ON THE THICKNESS CONTROL SCREWS
OR WELDS ON THE LEVELING ARMS. A LONGER
UNLOADING RAMP OR BLOCKS MAY BE NECESSARY TO RE-
DUCE THE ANGLE OF UNLOADING.
1. Remove tie down equipment.
2. Start and warm up engine. NOTE
If you have a problem unloading the paver, - STOP -
3. Set throttle at 1/2 operating RPM. Shift transmission LOOK - THINK!
into low range. Set steering control levers so paver
moves very slowly.
4. Make sure:
A. Screed position - UP LOADING
B. Extendable screed - IN
C. Gates below augers - CLOSED (Caution - 1. Move paver to base of ramp. Line up tracks with
Never back up with cutoff gates open.) the ramp. Load paver screed end first. Set
D. Speed range - LOW (Never shift Transmis- throttle at 1/2 operating RPM and steering
sion on incline.) control levers so paver moves very slowly onto the
. -- ramp.
5. Move the 'paver forward down the ramp as shown in
figure 15. 2. Make sure:
A. Screed position is - UP
B. Extendable screed - IN
c. Gates below auger - CLOSED
D. Speed range-low (Never shift transmissions
on grade).
3. With the steering control levers slowly guide the
paverupthe ramp. If the paver is loaded hopperfirst,
the weight of the operator on the walkway will tend to
tip the paver 0 nto the screed. See figure 16.
4. When the paver has reached the desired
UNLOADING position and is centered on the transport
trailer, stop the unit.
FIGURE 15
5. Lower screed to deck.
. ! DANGER! . 6. Shut down engine.
MAKE SURE THE ENGINE IS RUNNING AT HIGH
ENOUGH RPM'S TO PROVIDE THE HYDRAULIC 7. Secure paver to transport as directed by
PUMP WITH ENOUGH GALLONS PER MINUTE TO regulations.
FUNCTION PROPERLY.
8. Always have a helper on the ground who can
assist the operator in moving the paver onto the
transport.
16
--- Page 5 ---
MAINTENANCE ADJUSTMENTS 4. After the fe.eder is in position, lower the feeder onto
the safety prop. This will provide an extra margin
TO RAISE FEEDERS safety preventing safety propfrom accidentially be-
ing dislodged.
1. Fold hopperwings all the way in and pull bolts out.
Grabtopwings and pull out 5" or 6", then pullbottom
handleout til wing knuckles out. To let wingsdown
! CAUTION !
BEFORE RAISING OR lOWERING FEEDERS, FOLD
justpullontop of wingand letdownto whereboltswill
SIDES INTO THE FULL IN POSITION.
go in. see figure 30.
FIGURE 30
2. Raisefeeders by pushing feeder lift valve forward.
Thelocation ofthisvalvehaspurposelybee n placed
in an inconvenient position to prevent the acci-
dental raising of the feeders. See Figure 31.
FIGURE 32
! DANGER ! .
USE EXTREME CAUTION WHEN WORKING UNDER'
FEEDERS. CLEAR AREA OF UNTRAINED PER-
SONNEL. PLACE SAFETY PROP INTO SUPPORT
POSITION ANI) LOWER FEEDERS UNTIL SAFETY"
PROP IS UNDER LOAD AND FIRMLY WEDGED. .
FIGURE 31
3. IMMEDIATELY AFTER RAISING FEEDERS, PLACE
THE SAFETY PROP IN POSITION.
See figure 32.
26
--- Page 8 ---
~~-=-
..
/~irr~
-----22
20