PDF Parts Manual KCM 60Z7 Wheel Loader Deutz TCD3.6 Engine - 768 KB

This parts manual covers the KCM 60Z7 Wheel Loader and its Deutz TCD3.6 engine.

Inside you will find exploded-view drawings and comprehensive part number lists for the entire machine.

This is the definitive guide for identifying and ordering the correct replacement parts to minimize downtime.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
93206-00370


                                                                         60Z7
                                                                                                                               August 2015


                                                                         SHOP MANUAL
                                                                                            SHOP MANUAL

                                                                                            WHEEL LOADER


                                                                     Function & Structure
                                                                     General Information
                                                                                            60Z7

                                                                                            General Information
                                                                         93206-00370        Function & Structure


                                                                                            Powered by DEUTZ TCD36 Engine

                                                                                            Serial No. 60D1-8001 and up
©2015 KCM Corporation. All rights reserved.   Printed in Japan (K)
                                                   ( オセアニア用 )

--- Page 3 ---
SECTION 1 GENERAL
          Group 1 Specifications

(Blank)


                  T1-1-2

--- Page 4 ---
SECTION 1 GENERAL
                                               Group 2 Component Layout

Engine


                                                                                                             12


     1
                                                             2
     8

     7

     6                                                       3


     5
                                                         4
                                                                                                                   9
                  13
                                                                               11    10
                                                                                                                       TNCC-01-02-010


1-   Common Rail Pressure Sensor   5-   Engine Oil Filter            8-  Boost Pressure/Boost        11- Crank Speed Sensor
2-   Alternator                    6-   Starter                          Temperature Sensor          12- EGR Valve
3-   Fan Belt                      7-   Coolant Temperature Sensor   9- Engine Oil Pressure Sensor   13- Supply Pump
4-   Auto Tension Pulley                                             10- Cam Angle Sensor


                                                                 T1-2-10

--- Page 5 ---
SECTION 1 GENERAL
                                  Group 3 Component Specifications

Engine

COOLING SYSTEM       Cooling Fan                Dia. 510 mm (20 in), 7 Blades, Hybrid
                     Thermostat                 Cracking Temperature at Atmospheric Pressure : 88 °C (190 °F)
                                                Full Open 95 °C (203 °F)
LUBRICATION SYSTEM   Lubrication Pump Type      Trochoid Pump
                     Oil Filter                 Full-Flow Paper Element Type
                     Oil Cooler                 Water Cooled Integral Type
STARTING SYSTEM      Motor                      Magnetic Pinion Shift Reduction Type
                     Voltage/Output             24 V/4.0 kW
PREHEAT SYSTEM       Preheating Method          Glow Plug Type
ENGINE STOP SYSTEM   Stop Method                Fuel Shut-Off (Electronic Control)
ALTERNATOR           Type                       AC Type
                     Voltage/Output             24 V/80 A
SUPERCHARGING        Type                       Exhaust-Turbocharger Type, Forced Lubrication
SYSTEM
FUEL SYSTEM          Type                       Common Rail Type
                     Governor                   Electronic All Speed Control
                     Injection Nozzle           Electrical Multi-Hole Injector


                                               T1-3-2

--- Page 6 ---
SECTION 1 GENERAL
                                Group 3 Component Specifications

Electrical Component

ENGINE OIL PRESSURE    Operating Pressure         48 kPa (0.5 kgf/cm2, 7.0 psi)
SENSOR
COOLANT TEMPERATURE Operating Temperature         -10 to 110 °C (14 to 230 °F)
SENSOR
FUEL LEVEL SENSOR      Resistance Value           Empty : 90 +10/0 Ω, Full : 10 0/-4 Ω
HYDRAULIC OIL          Operating Temperature      -30 to 120 °C (-22 to 248 °F)
TEMPERATURE SENSOR
BATTERY RELAY          Voltage/Current            24 V/100 A
PREHEAT RELAY 2        Voltage/Current            24 V/100 A


                                                T1-3-12

--- Page 7 ---
SECTION 2 SYSTEM
                                              Group 2 Control System


                Input Signal                                                    Output Signal
                                                          Engine Control (ECM)
Accelerator Pedal Sensor                                  Accelerator Pedal Control

                                                          HST Pump Control (Forward/Reverse Control Solenoid
                                                          Valve)
Forward/Reverse Lever                                     Forward/Reverse Lever Control

                                                          HST Motor Control (Travel Control Solenoid Valve,
                                                          Displacement Angle Control Solenoid Valve)
Shift Switch                                              Driving Slow Speed Selection Control
Slow Speed (L) Select Switch                              Traction Force Limit Control
Power Mode Switch                                         Traction Control
Quick Shift Switch                                        Overrun Limit Control
Traction Control Switch                                   Engine Protection Control
Ride Control Switch (Option)                              Overheat Prevention Control
Machine Speed Sensor                                MC    Driving Slow Speed Switching Shock Reduction Control
HST Pressure Sensor                             
Pressure Sensor (Front Attachment Pressure)              Transmission Control (Travel Mode Selector Solenoid
                                                          Valve)
                                                            Driving Slow Mode Selection Control

Coolant Temperature                                      Other Controls
Sensor
                                   ECM
Crank Speed Sensor                                        Backup Light Lighting Control
Cam Angle Sensor                                          Ride Control Function (Option)
                                                           Parking Brake Operation Indicator Control
                                             CAN           Secondary Steering Control (Option)
                                                           Bucket Auto Leveler Control
                                                           Lift Arm Float Control (Hydraulic Pilot Type) (Option)
Parking Brake Pressure                                    Lift Arm Kickout Control (Hydraulic Pilot Type) (Option)
Sensor
HST Oil Temperature             Monitor
Sensor                          Controller
Secondary Check            
Switch (Option)


                                                      T2-2-2

--- Page 8 ---
SECTION 2 SYSTEM
                                              Group 2 Control System

 Forward/Reverse Lever Reverse (R) Position

Operation:
  1. When forward/reverse lever (1) is set in the reverse
     (R) position (f ), current flows from terminal R in
     forward/reverse lever (1) to MC (2).

  2. MC (2) activates reverse side solenoid valve (3) of
     forward/reverse control solenoid valve (4) of HST
     pump (10).

  3. Pressure oil from HST charge pump (7) is routed to
     the spring chamber of displacement angle control
     cylinder (8) on reverse side of HST pump (10)
     through reverse side solenoid valve (3).

  4. Pressure oil ed from HST pump (10) flows to port B
     (h) in the HST motor through y port A and rotates
     the HST motor in reverse.


                                                           T2-2-12

--- Page 9 ---
SECTION 2 SYSTEM
                                             Group 2 Control System

  Driving Slow Speed Selection Control
  (only Cab Spec. Machine)
                                                                             A
Purpose:
Machine speed in slow-speed driving is optimized.

IMPORTANT: This control functions when shift switch
   (3) is set in slow position (4) while driving forward.

Operation:
  1. Slow Speed (L) Select Switch (5) sends voltage
     signal according to the rotation angle to MC (6).
                                                                                                            B
                                                                                 C
  2. MC (6) calculates the machine speed according to                                D
     the voltage signals sent from machine speed sensor
     (1) and slow speed (L) select switch (5).                                                               TNCC-02-02-002

                                                              A-   HST Motor Displacement   B-   Machine Speed
  3. MC (6) activates displacement angle control                   Angle                    D-   11.5 km/h (7 mph)
     solenoid valve (7) according to the machine speed.       C-   7 km/h (4.3 mph)


  4. Pressure oil from HST motor (8) is routed to
     displacement angle control cylinder (9) of HST
     motor (8) through displacement angle control
     solenoid valve (7).

  5. Displacement angle control cylinder (9) sets HST
     motor (8) to the displacement angle according to
     the machine speed.

  6. Consequently, the rotation speed of HST motor (8)
     is changed to the selected speed of slow (L) driving
     speed limit switch (5) while driving in slow speed.


                                                         T2-2-22

--- Page 10 ---
SECTION 2 SYSTEM
                                             Group 2 Control System

  Overheat Prevention Control
Purpose:
When the coolant temperature and HST oil temperature
rise abnormally, the overheat prevention control prevents
abnormal rise of coolant temperature by limiting
minimum displacement angle of HST motor (6), reducing
HST motor (6) speed and reducing the machine speed.


Operation:
  1. ECM (2) receives the signals from coolant
     temperature sensor (1).

  2. ECM (2) sends the coolant temperature signals to
     MC (4) by using CAN communication (3).

  3. Signals from HST oil temperature sensor (9) is sent
     to monitor controller (8).

  4. Monitor controller (8) sends HST oil temperature
     signals to MC (4) by using CAN communication (3).

  5. MC (4) activates displacement angle control
     solenoid valve (5) by calculating the displacement
     angle of HST motor (6).

  6. Pressure oil from HST motor (6) is routed to
     displacement angle control cylinder (7) of HST
     motor (6) through displacement angle control
     solenoid valve (5).

  7. Displacement angle control cylinder (7) increases
     displacement angle of HST motor (6).

  8. Therefore, the rotation speed of HST motor (6) is
     decreased and the machine speed is decelerated.

  9. As the HST pump speed is also decreased and
     engine load is decreased, rise of the coolant and
     HST oil temperature is reduced.


                                                           T2-2-32

--- Page 11 ---
SECTION 2 SYSTEM
                                              Group 2 Control System

  Slow Speed Selection by using Quick Shift Switch
  (4)
Operation:
  1. When quick shift switch (4) is pushed with shift
     switch (2) is in Hi position and the machine speed is
     10 km/h (6.2 mph) or lower, MC (3) activates travel
     mode selector solenoid valve (7).

  2. Pressure oil flowing from brake/transmission
     pump (a) is routed to travel mode selector valve (9)
     through drive mode selection solenoid valve (7),
     thus travel mode selector valve (9) is sifted.

  3. Pressure oil flowing from brake/transmission pump
     (a) is routed to clutch slow speed side (6) through
     drive mode selection valve (9), the clutch is shifted
     to the slow speed.

  4. When quick shift switch (4) is pushed again, MC (3)
     deactivates drive mode selection solenoid valve (7).

  5. Drive mode selection valve (9) is shifted by spring
     (8).

  6. Pressure oil flowing from brake/transmission pump
     (a) is routed to clutch high speed side (10) through
     drive mode selection valve (9), the clutch is shifted
     to the high speed.


                                                           T2-2-42

--- Page 12 ---
SECTION 2 SYSTEM
                                              Group 2 Control System

  Secondary Steering Control (Option)
Purpose:
When hydraulic pressure oil cannot be supplied to the
steering circuit due to the engine fault, the steering
operation cannot be made.
The secondary steering control activates secondary
steering pump (8) for a while, and makes the steering
operation possible.

IMPORTANT: Large capacity of electricity is required
   in order to operate secondary steering pump (8).
   Check secondary steering pump (8) within 1 or 2
   seconds.

 Operation of secondary steering pump (8) by operating
  secondary steering check switch (6) (option)

Operation:
  1. When secondary steering check switch (6) is set
     to the ON position, current from terminal #1-33 in
     monitor controller (4) flows to the ground circuit
     through secondary steering check switch (6).


  2. Monitor controller (4) connects the ground circuit
     of secondary steering pump relay (5) while current
     flows from terminal #1-33 in monitor controller (4)
     to the ground circuit, thus secondary steering pump
     relay (5) is excited continuously.


  3. Monitor controller (4) lights the secondary steering
     indicator while secondary steering pump relay (5) is
     excited.


  4. Current from battery (a) flows to secondary steering
     motor (7) through secondary steering pump relay
     (5) and operates secondary steering pump (8).


  5. Pressure oil from secondary steering pump (8)
     is supplied to steering circuit (b) and makes the
     steering operation possible for a while.


                                                          T2-2-52

--- Page 13 ---
SECTION 2 SYSTEM
                                                Group 2 Control System

  Lift Arm Kickout Control (Hydraulic Pilot Type)
  (Option)

Purpose:
The lift arm kickout control automatically stops raising the
lift arm at any height when returning the lift arm to the
highest position.

Operation:
  1. Plate (3) is located in front of lift arm proximity                 7. At the same time, plate (3) passes by lift arm
     switch (2) when the bucket is lowered. While plate                     proximity switch (2).
     (3) passes by lift arm proximity switch (2), lift arm
     proximity switch (2) is turned ON.
                                                                         8. When plate (3) becomes distant from lift arm
                                                                            proximity switch (2), lift arm proximity switch (2) is
  2. Kickout relay (8) (coil side) is connected to the                      turned OFF, kickout relay (8) (coil side) is disconnect
     ground through lift arm proximity switch (2). Then,                    from the ground, and kickout relay (8) is turned OFF.
     kickout relay (8) turns ON.

                                                                         9. As coil (5) on the lift arm raise side is disconnected
  3. Coil (5) on the lift arm raise side is connected to the                from the ground, it turned OFF.
     ground through kickout relay (8) (contact side).

                                                                     10. Therefore, the lift arm control lever is returned
  4. Current from battery (a) flows to coil (5) on the lift              to neutral (N) position (c). As lift arm spool (7) in
     arm raise side and excites coil (5) on the lift arm                 control valve (6) also returns to neutral position (c),
     raise side.                                                         lift arm cylinder (1) stops.


  5. When the lift arm control lever is moved farther                11. Consequently, the lift arm raising operation is
     than the lift arm raise detent position (position to                stopped automatically.
     move farther than the raise position), the lift arm
     control lever is held by coil (5) on the lift arm raise
     side and pressure oil from pilot valve (4) moves lift
     arm spool (7) in control valve (6).


  6. Pressure oil from main pump (e) flows to the bottom
     side of lift arm cylinder (1) through lift arm spool (7)
     in control valve (6) and raise the lift arm.


                                                               T2-2-62

--- Page 14 ---
SECTION 2 SYSTEM
                                                Group 3 ECM System

  Fuel Injection Timing Control                                   Operation of Fuel Injection:
                                                                    1. Fuel pressure is always applied to nozzle (6) in the
                                                                       injector.
Purpose:
The fuel injection timing control calculates the best fuel            2. When turning electromagnetic coil (9) in two-way
injection timing.                                                        valve (2) ON, high-pressure fuel in control chamber
                                                                         (5) returns to the fuel tank through orifice A (4).
Operation:
                                                                      3. Therefore, hydraulic piston (10) is raised and nozzle
  1. ECM calculates the fuel injection timing according
                                                                         (6) is opened so that the injection starts.
     to the engine speed and fuel injection amount.
                                                                      4. When turning electromagnetic coil (9) in two-way
  2. ECM turns two-way valve (2) in the injector ON/OFF
                                                                         valve (2) OFF, valve (8) is closed and the circuit to
     according to fuel injection timing.
                                                                         the fuel tank is closed. High-pressure fuel from the
                                                                         common rail flows to control chamber (5) through
  Fuel Injection Rate Control                                            orifice B (12).
                                                                      5. Therefore, when high-pressure fuel flows to control
Purpose:                                                                 chamber (5), hydraulic piston (10) is lowered by the
The fuel injection rate control improves combustion in                   pressure difference due to movement of hydraulic
the engine cylinder.                                                     piston (10). As nozzle (6) is closed, the injection
                                                                         stops.
Operation:
  1. The injector injects small amount of fuel (pilot
     injection) first and ignites.
  2. After igniting, the injector makes secondary
     injection (main injection).
  3. ECM controls fuel injection timing and fuel injection
     amount by turning two-way valve (2) in the injector
     ON/OFF.


                                                             T2-3-8

--- Page 15 ---
SECTION 2 SYSTEM
          Group 3 ECM System

(Blank)


                T2-3-18

--- Page 16 ---
SECTION 2 SYSTEM
                                             Group 4 Hydraulic System

Steering Stop Circuit (When steering cylinder is at
stroke end)

1. Pressurized oil which flows from port P in steering
   valve (4) to greater (6) is divided in steering spool
   (14) and is routed to port LS2 through port LS and
   orifice 3 (8) in priority valve (10).

2. When steering cylinder (5) reaches the stroke end,
   the pressure at port LS 2 in priority valve (10) also
   increases due to pressurized oil flowing from main
   pump (1) through port LS.

3. When the pressure at port LS2 exceeds the
   specified level, relief valve (12) in priority valve (10)
   is operated and pressurized oil routed to port LS2
   flows from relief valve (12) to hydraulic oil tank (13).

4. Therefore, the pressure difference between port LS1
   and port LS2 occurs due to orifice 2 (9).

5. Therefore, priority spool (2) in priority valve (10) is
   moved to the left and pressurized oil from main
   pump (1) flows to control valve (3).


                                                             T2-4-10

--- Page 17 ---
SECTION 2 SYSTEM
                                               Group 4 Hydraulic System

 Combined operation of steering and lift arm raise:

fNOTE: The lift arm raise operation when turning the
   steering wheel (right) is explained here.

  1. When steering wheel (4) is rotated right, pressurized
     oil (CF) from priority valve (3) is supplied to steering
     valve (5). At the same time, other pressurized oil is
     supplied to control valve (9) from port EF. (Refer to
     Priority Valve Circuit (When steering is in neutral).)

  2. Pressurized oil from port CF in priority valve (3)
     flows to steering spool (7) through load check valve
     (8) in steering valve (5).

  3. Pressurized oil flowing to steering spool (7) moves
     steering cylinders (6) and the machine turns right.
     (Refer to Steering Circuit.)

  4. Lift arm spool (13) in control valve (9) is shifted
     when the front attachment control lever is set to lift
     arm raise operation.

  5. Pressurized oil port EF in priority valve (3) flows to
     lift arm spool (13) through load check valve (14) in
     control valve (9).

  6. Pressurized oil flowing to lift arm spool (13) moves
     lift arm cylinders (11) and raises the lift arm.

  7. Therefore, steering (right) operation and lift arm
     raise operation are simultaneously made.


                                                              T2-4-20

--- Page 18 ---
SECTION 2 SYSTEM
                                          Group 4 Hydraulic System

Inching Circuit

1. When depressing brake pedal (7), declutch valve
   (6) is activated and pressurized oil from DA valve (3)
   flows to hydraulic oil tank (5).

2. Therefore, the displacement angle control pressure
   of HST pump (1) decreases and displacement angle
   control cylinder (4) returns to the neutral position.

3. Consequently, the displacement angle of HST
   pump (1) is changed to the neutral position and the
   delivery flow rate of HST pump (1) decreases.

4. As the delivery flow rate HST pump (1) decreases,
   the rotation speed of the HST motor decreases and
   the machine speed is decelerated.

5. The displacement angle control pressure of HST
   pump (1) is changed according to the depressing
   amount of brake pedal (7).
   When brake pedal (7) is depressed fully, the
   displacement angle of HST pump (1) is in the
   neutral position.


                                                       T2-4-30

--- Page 19 ---
SECTION 2 SYSTEM
                                               Group 4 Hydraulic System

  Parking Brake Circuit

fNOTE: When parking brake solenoid valve (13) is ON,
   parking brake (12) is released. When parking brake
   solenoid valve (13) is OFF, parking brake (12) is applied.
   (Refer to Electrical System.)

   Circuit with parking brake (12) released:

  1. Pressurized oil from brake/transmission pump (1) is
     routed to parking brake solenoid valve (13).

  2. When the parking brake switch is turned OFF
     (release), parking brake solenoid valve (13) is turned
     ON and the spool of parking brake solenoid valve
     (13) is moved.

  3. Pressurized oil from brake/transmission pump (1)
     compresses the spring of parking brake (12) in
     transmission (11) through parking brake solenoid
     valve (13) so that parking brake (12) is released.


                                                                T2-4-40

--- Page 20 ---
SECTION 2 SYSTEM
                                            Group 5 Electrical System

Electric Power Circuit (Key Switch: OFF)
The battery (2) minus terminal is grounded to the body.
Current from the battery (1) plus terminal flows as shown
below when key switch (1) is in the OFF position.

Battery (2)    Fusible Link   Key Switch (1) Terminal B
               A (4)          Fuse Box A(5)            Terminal Fuel Pump Relay (Power) (6)
                                                       #4
                                                       Terminal Horn Relay (Power) (7)
                                                       #5
                                                       Terminal Flasher (Power) (8)
                                                       #6       Hazard Light Switch (9)
                                                       Terminal Load Dump Relay (Power) (22)
                                                       #7       Communication Terminal (Power) (10)
                                                                ICF (C1) (Power) (11)
                                                                ICF (C2) (Power) (12)
                                                                Option (13)
                                                                Monitor Controller (Backup Power) (14)
                                                       Terminal ECM (Power) (21)
                                                       #8
                                                       Terminal Light Switch (15)
                                                       #17
                                                       Terminal Option 1 (16)
                                                       #18
                              Fuse Box B (17)          Terminal Radio (Power) (18)
                                                       #11      Cab Light (Power) (19)
                                                               Tachograph (Power) (20)


                                                        T2-5-4

--- Page 21 ---
SECTION 2 SYSTEM
                                              Group 5 Electrical System

Engine Starting Circuit (Key Switch: START)
IMPORTANT: ECM receives the forward/reverse
   lever position signal from MC by using CAN
   communication.

  Forward/Reverse Lever at Neutral Position

  1. When key switch (1) is set to the START position,
     terminal B (2) is connected to terminals M (3) and ST
     (4) in key switch (1).

  2. Current from terminal M (3) flows through fuse #13
     of fuse box A (10) and excites battery relay (6). The
     battery power from battery relay (6) is routed to the
     relay contact in starter motor (9) through starter
     relay 1 (8).

  3. At the same time, current from fuse #14 of fuse box
     A (10) flow to terminal K88 in ECM (11) and the key
     ON signal is sent to ECM (11).

  4. ECM (11) receives the forward/reverse lever
     neutral position signal from MC (12) by using CAN
     communication (13). Then, ECM (11) connects
     terminal K73 in ECM (11) to the ground circuit.

  5. Current from terminal ST (4) flows to terminal K35 in
     ECM (11) and the start signal is sent.

  6. Current from terminal K28 in ECM (11) flows to the
     coil in starter relay 1 (8) and starter relay 1 (8) is
     turned ON.

  7. Therefore, current from starter relay 1 (8) also flows
     to starter motor (9).

  8. Consequently, the relay in starter motor (9) is turned
     ON and starter motor (9) rotates.


                                                              T2-5-14

--- Page 23 ---
SECTION 2 SYSTEM
                                               Group 5 Electrical System

Pilot Shut-Off Circuit (Key Switch: ON)
(Hydraulic Operated Type) (Option)
 Control Level Lock Switch (9): ON (Lock) Position

  1. When key switch (1) is in the ON position, current
     from battery relay (3) flows to pilot shut-off relay (7)
     through fusible link (100 A) (5), fuse #15 of fuse box
     A (6).

  2. When control lever lock switch (9) is in the ON (lock)
     position, terminals #2 and #4 are connected inside
     control lever lock switch (9).

  3. Pilot shut-off relay (7) (coil side) is connected to the
     ground through control lever lock switch (9). Then,
     pilot shut-off relay (7) is excited.

  4. Current which flows to pilot shut-off solenoid valve
     (8) from pilot shut-off relay (7) (contact side) stops
     flowing. Then, pilot shut-off solenoid valve (8) is
     turned OFF.

  5. Therefore, pressure oil which flows to the pilot valve
     from the HST charging pump is blocked by pilot
     shut-off solenoid valve (8).

  6. Consequently, pressure oil from the HST charging
     pump is not supplied to the pilot valve. (Refer to
     Hydraulic System.)

  7. Current from fuse #11 of fuse box A (6) flow to
     terminals #8 and #9 in control lever lock switch
     (9) and turn on the indicators of control lever lock
     switch (9).


                                                            T2-5-24

--- Page 24 ---
SECTION 2 SYSTEM
                                            Group 5 Electrical System

Front Wiper Circuit (Front Wiper Switch (6)): Fast)
                                                                                                  c
                                                                                                             b
1. When front wiper switch (6) is set to fast position (c),
   monitor controller (8) turns ON wiper relay (F) 1 (3)
   and wiper relay (F) 2 (2).
                                                                            d                                           a
2. Current from fuse #3 of fuse box B (7) flow to wiper
   motor (F) (1) and the front wiper is operated at fast
   speed.


                                                                                                                  MNEC-01-076


                                                                                   Front Wiper Switch

                                                              a-   INT. Position             c-   Fast Position
                                                              b-   Slow Position             d-   Washer Switch


                                                         T2-5-34

--- Page 25 ---
SECTION 2 SYSTEM
                                              Group 5 Electrical System

Cab Light Circuit
  Front Cab Light Circuit                                              Rear Cab Light Circuit

  1. When front cab light switch (3) is set to neutral                 1. When rear cab light switch (8) is set to the ON
     position (4), front cab light (2) is connected to the                position, rear cab light (7) is connected to the
     ground through door open/close switch (6).                           ground.

  2. When the cab door is opened, door open/close                      2. Current from fuse #11 of fuse box B (1) flow to rear
     switch (6) is turned ON. Current from fuse #11 of                    cab light (7) and turns on rear cab light (7).
     fuse box B (1) flow to front cab light (2) and turns on
     front cab light (2).

  3. When the cab door is closed, door open/close
     switch (6) is turned OFF. Door open/close switch (6)
     is disconnected from the ground and cab light (2) is
     tuned off.

  4. When front cab light switch (3) is set to ON position
     (5), front cab light (2) is connected to the ground.

  5. Current from fuse #11 of fuse box B (1) flow to front
     cab light (2) and turns on cab light (2).


                                                             T2-5-44

--- Page 26 ---
SECTION 2 SYSTEM
                                               Group 5 Electrical System

Work Light Circuit
  1. When key switch (1) is set to the ON position,
     terminal B (2) is connected to terminal M (3) in key
     switch (1).

  2. Current from terminal M (3) flows through fuse #13
     of fuse box A (8) and excites battery relay (5).

  3. Current from battery (4) flows to light switch (10)
     through battery relay (5), fusible link (A) (6), fuse #17
     of fuse box A (8).

  4. When light switch (10) is set to the S position or H
     position, current flows to work light switch (13) from
     light switch (10) and turns on switch light (20) of
     work light switch (13).

  5. When front work light position (14) of work light
     switch (13) is pushed, terminals #1 and #2 are
     connected inside work light switch (13).

  6. Current from terminal #2 of work light switch (13)
     flows to front work light relay (16) and excites it.

  7. Current from fuse #5 of fuse box B (9) flows to front
     work lights (17, 18) through front work light relay
     (16) and turns on front work lights (17, 18).

  8. At the same time, current from fuse #5 of fuse box B
     (9) flows to monitor controller (19) and turns on the
     work light indicator.


                                                            T2-5-54

--- Page 27 ---
SECTION 2 SYSTEM
                                               Group 5 Electrical System

Hazard Light Circuit
  1. Current from battery (2) flows to flasher (6), turn
     signal light relay (R) (14) (contact side), and turn
     signal light relay (L) (15) (contact side) through
     fusible link A (4), and fuse #6 of fuse box A (5).

  2. In addition, current from fuse #6 of fuse box A (5)
     flows to hazard light switch (7).

  3. When light switch (11) is set to S position (12) or H
     position (13), current flows to hazard light switch (7)
     from light switch (11) and turns on switch light 1 (9)
     of hazard light switch (7).

  4. When hazard light switch (7) is set to ON position
     (8), current from hazard light switch (7) flows to turn
     signal light relay (R) (14) (coil side) and turn signal

View the complete manual on HeyDownloads →