PDF Operator's Manual John Deere 6.8L Compressed Natural Gas Engine - 476 KB

Safely and efficiently operate your John Deere 6.8L Compressed Natural Gas (CNG) engine with this official operator's manual.

It covers all aspects of daily operation, critical safety precautions, and routine maintenance checks.

Understanding your engine's specific requirements is key to achieving optimal performance and longevity.

This manual is an invaluable resource for anyone working with this advanced powertrain.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
6.8L Compressed
Natural Gas Engine
     (PowerTech™)
 *OMRG27896*


                       OPERATOR'S MANUAL
                  POWERTECH 6.8 L 6068 Compressed
                        Natural Gas Engine
                     OMRG27896 ISSUE 03AUG21                     (ENGLISH)


                                       CALIFORNIA
                                   Proposition 65 Warning

                  Diesel engine exhaust and some of its constituents
                 are known to the State of California to cause cancer,
                      birth defects, and other reproductive harm.


               If this product contains a gasoline engine:

                                          WARNING

                    The engine exhaust from this product contains
                  chemicals known to the State of California to cause
                   cancer, birth defects or other reproductive harm.


               The State of California requires the above two warnings.
               Additional Proposition 65 Warnings can be found in this manual.

               John Deere Power Systems
                                             PRINTED IN U.S.A.

--- Page 3 ---
Identification Numbers


Engine Option Codes

                          EREED NHOJ                             4r9e0b0m0u0N
                                                                            U8606EP
                                                                                                              A
                                    90CFH8606                      L 8.6               F2372
                                 1111 9931 5241 4251 6061 8071 8291 2002 9962 5182 9092 8003 2153 4193 6204


                                                                                                                                                        RG24026 —UN—05AUG13
                                 1934 7064 2074 3084 3094 2005 3015 5125 7045 1155 5165 9075 7295 3456 1086
                                 1096 3F27 6037 3077 7987 2248 1198 5089


                               oN remotsuC               .          SEDOC NOITPO


                                                          Option Code Label Example
A—Engine Base Code (example)

OEM engines have an engine option code label affixed to                    An additional option code label may also be delivered (in
the rocker arm cover. These codes indicate which of the                    a plastic bag attached to the engine or inserted in the
engine options were installed on your engine at the factory.               machine documentation). It is recommended to place this
When in need of parts or service, furnish your authorized                  label either on this page of the operators manual or in the
servicing dealer or engine distributor with these numbers.                 Engine Owner's Warranty booklet under Option Codes.
The engine option code label includes an engine base                       The machine manufacturer may have placed the label in a
code (A). This base code must also be recorded along                       specific accessible area (inside the enclosure or close to
with the option codes. At times it will be necessary to                    a maintenance area).
furnish this base code to differentiate two identical option
codes for the same engine model.                                           Your engine option code label may not contain all option
                                                                           codes if an option has been added after the engine left
The first two digits of each code identify a specific group,               the producing factory.
such as alternators. The last two digits of each code
identify one specific option provided on your engine, such                 If option code label is lost or destroyed, consult your
as a 24 volt, 120 amp alternator.                                          servicing dealer or engine distributor selling the engine for
                                                                           a replacement.
If an engine is ordered without a particular component, the
last two digits of that functional group option code will be               Record your engine Base Code (A) in the spaces provided
99, 00, or XX. The following list shows only the first two                 below for easy reference.
digits of the code numbers. For future reference such as
ordering repair parts, it is important to have these code                    Engine Base Code (A):
numbers available. To ensure this availability, enter the
third and fourth digits shown on your engine option code
label in the spaces provided on the following page.
 Option Codes      Description                                             Option Codes          Description


 10                Paint Protection                                        56                    Paint
 11                Rocker Arm Cover                                        57                    Water Pump Inlet
 12                Oil Filler                                              58                    Power Take Off
 13                Crankshaft Pulley                                       59                    Oil Cooler/Oil Filter
 14                Flywheel Housing                                        60                    Add-On Fan Drive Pulley
 15                Flywheel                                                61                    After Treatment Device/Muffler
 16                Fuel Injection System                                   62                    Alternator Mounting
 17                Air Inlet                                               63                    Low-Pressure Fuel Lines
 18                Air Cleaner                                             64                    Exhaust Elbow
 19                Oil Pan                                                 65                    Turbocharger
 20                Water Pump                                              66                    Temperature Switch
 21                Thermostat Cover                                        67                    Engine Sensors
                                                                       Continued on next page                              RG,RG34710,5004 -19-12JUN17-1/2


                                                                  01-3                                                                                 080621

                                                                                                                                                   PN=11

--- Page 4 ---
Fuels, Lubricants, and Coolant
Natural Gas Recommendations                                        Maximum Propane Content ......................................... 5 percent
                                                                   Maximum Butane Content .......................................... 1 percent
NOTE: Dry natural gas is a mixture of methane,
    ethane, propane, butane, and other inert                       Maximum Hydrogen Sulfide (H2S)................................... 10 ppm
    gases. Dry natural gas is also referred to as
                                                                   Minimum Octane Rating .................................................... 118
    Commercial Pipeline Natural Gas.
                                                                   Minimum Heat Value ........................... 33.72 kJ/L (905 BTU/cu ft)
Dry natural gas that meets SAE J1616 Fuel Quality
Specification is recommended for use in John Deere
Natural Gas engines.
                                                                                                                 DPSG,OUOE003,7818 -19-13MAR98-1/1


Engine Break-In Oil
                                                                  If John Deere ENGINE BREAK-IN OIL is not available,
New engines are filled at the factory with John Deere             use a natural gas engine oil as specified later in this
ENGINE BREAK-IN OIL. During the break-in period, use              manual during the first 2,500 miles of operation.
John Deere ENGINE BREAK-IN OIL as makeup oil when
oil level falls BELOW the add mark.                               After the break-in period, always use natural gas engine
                                                                  oils as recommended in this manual.
Change the oil and filter after the first 2,500 miles of
operation of a new or rebuilt engine.                             IMPORTANT: DO NOT use engine oils meeting API
                                                                      CF-4 performance levels during the first 2,500
After engine overhaul, fill the engine with John Deere                miles of operation of a new or rebuilt engine. This
ENGINE BREAK-IN OIL.                                                  oil will not allow the engine to break-in properly.
                                                                                                                 DPSG,OUOE003,7818 -19-13MAR98-1/1


Natural Gas Engine Oil
Use oil viscosity based on the expected air temperature
range during the period between oil changes.
SAE 15W-40 oil is preferred.
The use of heating devices may permit extension of the
lower temperature limits, but requires special precautions.
See your engine servicing dealer for recommendations.
The service interval for oil and filter changes is 12 months
or 12,500 miles, whichever occurs first.
Oils meeting the following specifications are
recommended:


                                                                                                                                                     TS1661 —UN—10OCT97
API Service Classification CG-4 with 0.4 to 0.6%
sulfated ash content.
Other oils claiming natural gas engine oil performance
may be used, but the drain interval is reduced to 12
months or 10,000 miles, whichever occurs first. Ashless
natural gas engine oils are not allowed.
                                                                                       Engine Oil Temperature Ranges

                                                                                                                 DPSG,OUOE003,7818 -19-18MAR15-1/1


                                                           10-1                                                                               PN=21
                                                                                                                                                    080621

--- Page 5 ---
Operating the Engine


Warming the Engine                                      The Electronic Control Unit (ECU) will not allow full power
Allow engine to warm up before resuming normal          until engine is warmed up to 160°F (71°C).
operation.
                                                                                           DPSG,OUOE003,7821 -19-13MAR98-1/1


                                                 15-3                                                                    080621

                                                                                                                     PN=31

--- Page 6 ---
Maintenance—12 Months/12,500 Miles


Checking Air Intake System
1. Check clamps on piping that connects the air cleaner
   to turbocharger. Tighten clamps as necessary. This
   will help prevent dirt from entering the air intake
   system, causing internal engine damage.


                                                                                                                                             RG7292A —UN—16MAR98
2. Test air restriction indicator (A) for proper operation.
   Replace indicator as necessary.
3. Refer to vehicle operator’s manual for further
   instructions on servicing the air filter.

  A—Air Restriction Indicator
                                                                                           Air Restriction Indicator
                                                                                                              DPSG,OUOE003,7828 -19-16MAR98-1/1


Checking Cooling System

    CAUTION: Explosive release of fluids from
    pressurized cooling system can cause
    serious burns.
     Shut off engine. Only remove filler cap when


                                                                                                                                             TS281 —UN—15APR13
     cool enough to touch with bare hands. Slowly
     loosen cap to first stop to relieve pressure
     before removing completely.

1. Check entire cooling system for leaks. Tighten all
   clamps securely.
                                                                                        Service Cooling System Safely
2. Thoroughly inspect all cooling system hoses. Replace
   hoses when hard, flimsy, or cracked.
                                                                           escape when filling system. Retighten plug
IMPORTANT: Air must be expelled from cooling                               when all the air has been expelled.
    system when system is refilled. Loosen plug
    in side of thermostat housing to allow air to
                                                                                                              DPSG,OUOE003,7829 -19-16MAR98-1/1


Checking Effectiveness of Coolant Solution
When your coolant has accumulated 12 months or 12,500
miles of operation, or anytime the concentration of coolant
solution is in question, the effectiveness of your engine
coolant should be evaluated by obtaining a coolant sample.

                                                                                                                                             RG7397 —UN—05DEC97
Maintaining the correct coolant conditioner concentration
(SCAs) and freeze point is essential in your cooling
system to protect against liner pitting, corrosion, and
freeze-ups due to incorrect coolant dilution.
A coolant strip test kit provides a simple, effective way to
check freeze point and molybdate/nitrite levels.
                                                                                            Coolant Sampler Tool
For a more thorough evaluation of your coolant,
CoolScan™ is a John Deere sampling program to help
you monitor the effectiveness of your engine’s coolant
solution and identify potential problems before they cause
serious damage.
CoolScan is a trademark of Deere & Company.
                                                               Continued on next page                         DPSG,OUOE003,7830 -19-16MAR98-1/2


                                                          30-5                                                                              080621

                                                                                                                                        PN=41

--- Page 7 ---
Maintenance—24 Months/25,000 Miles


5. If valves need adjusting, use following valve clearance
   adjustment specifications. Loosen the locknut on
   rocker arm adjusting screw. Turn adjusting screw until
   feeler gauge slips with a slight drag. Hold the adjusting
   screw from turning with screwdriver and tighten locknut
   to 27 N·m (20 lb-ft.) Recheck clearance again after


                                                                                                                                                RG8855 —UN—16MAR98
   tightening locknut. Readjust clearance as necessary.
                              Specification
Intake Valve
Adjustment—Valve
Clearance (Cold)....................................................... 0.36 mm (0.014 in.)
Exhaust Valve
Adjustment—Valve
                                                                                                   Adjusting Valves
Clearance (Cold)....................................................... 0.46 mm (0.018 in.)

6. Replace rocker arm cover and crankcase ventilator
   tube.
                                                                                                                 DPSG,OUOE003,7839 -19-16MAR98-2/3


Valve Adjusting Sequence
NOTE: Firing order is 1-5-3-6-2-4.

Lock No. 1 piston at TDC compression stroke (B).
Adjust valve clearance on No. 1, 3, and 5 exhaust valves


                                                                                                                                                RG8934 —UN—16MAR98
and No. 1, 2, and 4 intake valves.
Rotate flywheel 360°. Lock No. 6 piston at TDC
compression stroke (C).
Adjust valve clearance on No. 2, 4, and 6 exhaust valves
and No. 3, 5, and 6 intake valves.
                                                                                               Valve Adjusting Sequence
   A—Front of Engine                             C—No. 6 TDC Compression
   B—No. 1 TDC Compression                         Stroke
     Stroke

                                                                                                                 DPSG,OUOE003,7839 -19-16MAR98-3/3


                                                                                     35-9                                                      080621

                                                                                                                                           PN=51

--- Page 8 ---
Lubrication and Maintenance Records


Service as Required                      • Service air cleaner elements
                                         • Add coolant
• Replace belts
Miles
Date
Miles
Date
Miles
Date
                                                                          DPSG,OUOE003,7851 -19-16MAR98-1/1


                                  70-2                                                                  080621

                                                                                                    PN=61

View the complete manual on HeyDownloads →