PDF Operator’s Manual Case CX245D SR Crawler Excavator - 6 MB
The official Operator’s Manual for the Case CX245D SR Crawler Excavator is your complete guide to safe and efficient operation.
This manual details all machine controls, safety features, and daily maintenance procedures.
Familiarity with this guide is essential for all operators to maximize productivity and ensure a safe work environment.
It provides the foundational knowledge needed to get the most out of your excavator.
PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
PDF viewer loading area
Text Preview from This Manual
The text below was extracted from the visible preview pages to help you confirm the manual contents before download.
--- Page 1 ---
ORIGINAL INSTRUCTIONS
CX245D SR
Crawler Excavator
OPERATOR’S MANUAL
Part number 90393403
1st edition English
April 2020
--- Page 3 ---
1 - GENERAL INFORMATION
Manual scope and required training level
Introduction to this manual • Topping up fluid levels
This manual gives information about the use of your • Greasing
CASE CONSTRUCTION machine as intended and under • Replacing consumable items such as light bulbs
the conditions foreseen by CASE CONSTRUCTION dur-
ing normal operation, routine service, and maintenance. Periodic service, conversions, and repairs
This manual does not contain all the information that re- Periodic service consists of activities that are necessary
lates to periodic service, conversions, and repairs that to maintain the expected life of the CASE CONSTRUC-
only trained service personnel can perform. Some of TION machine. These activities have defined intervals.
these activities may require appropriate facilities, techni-
cal skills, and/or tools that CASE CONSTRUCTION does Trained service personnel familiar with the machine char-
not supply with the machine. acteristics must perform these activities at the defined
intervals. Trained service personnel must comply with
The manual contains the chapters as shown on the Con- the information on periodic service and safe practices as
tents pages. See the Index at the end of this manual to partly specified by CASE CONSTRUCTION in this man-
locate specific items about your CASE CONSTRUCTION ual and/or other company literature.
machine.
Periodic service includes:
Normal operation • Oil change service for the engine, hydraulic circuits, or
transmission
Normal operation consists of the use of this machine
for the purpose CASE CONSTRUCTION intends by an • Periodic exchange of other substances or components
operator that: as required
• Is familiar with the machine and any mounted equip- Conversion activities rebuild the CASE CONSTRUCTION
ment or towed equipment machine in a configuration that is appropriate for a
• Complies with the information on operation and safe specific job site, crop, and/or soil conditions (e.g.,
practices as specified by CASE CONSTRUCTION in installation of dual wheels). Conversion activities must
this manual and by the signs on the machine be done:
• By trained service personnel familiar with the machine
Normal operation includes: characteristics
• Preparation and storage of the machine • By trained service personnel that comply with the
• Addition and removal of ballast information on conversion as partly specified by CASE
CONSTRUCTION in this manual, assembly instruc-
• Connection and disconnection of mounted equipment
tions, and/or other company literature
and/or towed equipment
• Adjustment and configuration of the machine and Repair activities restore proper function to a CASE CON-
equipment for the specific conditions of the job site, STRUCTION machine after a failure or degradation of
field, and/or crop performance. Dismantling activities occur during the
scrapping and/or dismantling of the machine.
• Movement of components into and out of working po-
sitions Trained service personnel familiar with the machine char-
acteristics must perform these activities. Trained service
Routine service and maintenance personnel must comply with the information for repair as
specified by CASE CONSTRUCTION in the service man-
Routine service and maintenance consists of the daily ual.
activities necessary to maintain the proper machine
function. The operator must:
Before you operate
• Be familiar with the machine characteristics
Read this manual before you start the engine or operate
• Comply with the information on routine service and safe
this CASE CONSTRUCTION machine. Contact your
practices as specified by CASE CONSTRUCTION in
CASE CONSTRUCTION dealer if:
this manual and by the signs on the machine
• You do not understand any information in this manual
Routine service can include:
• You need more information
• Fueling
• You need assistance
• Cleaning
• Washing
1-3
--- Page 4 ---
1 - GENERAL INFORMATION
• Dispose of DEF/ADBLUE® and any filter accumulations in accordance with all applicable Federal, State, and local
laws governing waste disposal.
US Environmental Protection Agency (EPA) Warranty Statement
CASE CONSTRUCTION warrants to the ultimate purchaser and each subsequent purchaser that the engine
is designed, built and equipped so as to conform with US Environmental Protection Agency (EPA) regulations
applicable at the time of manufacture and that it is free from defects in workmanship or material which would
cause it not to meet these regulations for a period of:
• 2 years or 1,500 hours of operation, whichever occurs first, for engines less than 19 kW (25 Hp)
• 5 years or 3,000 hours of operation, whichever occurs first, for engines greater than or equal to 19 kW (25 Hp)
NOTE: this warranty applies to all units operated in the United States or Canada.
Coverage
The model year, class of diesel engine, and emission application determination for your engine are identified on the
Emission Control Information Label. This label is affixed to one of the following areas of the engine: the top of en-
gine's rocker arm cover, the right-hand side of the oil pan, and the right-hand side of the engine front gear cover.
The warranty period begins on the date the new equipment is sold to the first retail purchaser. The presence of the
emission control label is the indication that the engine conforms to the applicable standards. Any emission control
system parts which are proven defective during normal use will be repaired or replaced during the warranty period.
The engine owner has responsibility to perform all the required maintenance listed in the Owner's Manual. CASE
CONSTRUCTION will not deny an emission warranty claim solely because no record of maintenance exists; however,
a claim may be denied if failure to perform maintenance resulted in the failure of a warranted part
It is recommended that replacement parts used for maintenance or repairs be CASE CONSTRUCTION Service Parts
to maintain the quality originally designed into your emission certified engine. The use of non- CASE CONSTRUC-
TION parts does not invalidate the warranty on other components unless the use of such parts causes damage to
warranted parts.
The manufacturer is liable for damages to other engine components caused by the failure of any warranted emission
control system part. CASE CONSTRUCTION is not responsible for failures resulting from improper repair or the use
of parts that are not genuine CASE CONSTRUCTION or CASE CONSTRUCTION approved parts.
Component coverage
New engines certified for sale and registered will have the following items covered by the emission warranty, depend-
ing on the emission level of the engine, if the items were first installed on the new engine as original equipment:
Fuel injection system Exhaust after treatment Devices (if applicable)
• Fuel injection pump • Diesel Oxidation Catalyst (DOC)
• Fuel injectors • Diesel Particulate Filter (DPF)
• Fuel injection lines • Selective Catalytic Reduction (SCR)
Air induction system • Diesel Exhaust Fluid (DEF) tank and dispensing sys-
tems
• Intake manifold
Exhaust Gas Recirculation Systems (EGR)
• Turbocharger system (includes exhaust manifold)
• Charge air cooler • EGR valve assembly
• EGR cooler
Positive Crankcase Ventilation (PCV) system (if
applicable) Cold Start Enrichment Systems
• PCV valve Electronic Control Units, Sensors, Solenoids, and Wiring
• Oil fill cap harnesses used in above systems
1-13
--- Page 5 ---
2 - SAFETY INFORMATION
7. Make sure that the hoods and doors are properly 8. Check that no part of the machine is encroaching on
latched. the highway. If this cannot be avoided, install the nec-
essary regulation signaling equipment.
Maintenance and adjustments
• Do not try to service this machine unless you have Avoid contact with skin, eyes and clothing.
first read and perfectly understood the safety messages Antidote:
and instructions featuring in this manual. External: rinse thoroughly with water and remove
soiled clothes.
• When carrying out service work always wear suitable
Internal: do not induce vomiting. Rinse the mouth out
dress. Avoid loose-fitting clothing.
with water. Seek medical advice.
• Release pressure completely in the hydraulic system Eyes: rinse thoroughly with water and seek medical
before disconnecting the hydraulic piping. Hydraulic oil advice.
escaping under pressure can cause serious injury.
• The pressure in the track tension cylinders is high. Fol-
• Before doing maintenance work on the machine, shut low the procedure described in this manual carefully for
down the engine and allow it to cool down. Otherwise, increasing or reducing track tension.
you could be burned.
• When carrying out a welding operation on the undercar-
• Before commencing any work on the machine, place a riage or upperstructure carriage as authorized by the
"Do not operate" tag on the right-hand control arm. manufacturer and in accordance with his instructions,
• Always wear eye protection when using a tool that disconnect the batteries, disconnect the alternator B+
might project metal particles. Use a hammer with a and D+ terminal wires and connect the welding appa-
soft face, such as copper, for installing pins. ratus earth cable to the component on which the weld-
ing operation is to be performed. Never connect the
• Badly carried out maintenance or adjustments can welding apparatus to the undercarriage when welding
cause serious injuries. If you do not understand a on the upperstructure (or vice-versa). Never connect
servicing or adjustment procedure, consult your CASE the welding apparatus earth to a component of the hy-
CONSTRUCTION Dealer. draulic system.
• If the attachment is raised or if the machine moves with- • When using compressed air, take the necessary pre-
out an operator, serious injury can result. Before car- cautions to protect your face.
rying out maintenance on this machine, proceed as fol- • Clean the machine regularly. Accumulations of grease,
lows: dirt and debris can cause injuries or damage the ma-
Park the machine on flat, level ground. chine.
Lower the attachment until it is resting on the ground.
Lower the dozer blade (if equipped) until it rests on the • Periodically inspect the fastening of the main compo-
ground. nents, as part of the machine maintenance programme:
Stop the engine and remove the ignition key. counterweight, turntable bearing and operator's com-
Lock the tracks to prevent any machine movement. partment. In the event of problems, consult your CASE
CONSTRUCTION Dealer.
• Any unauthorized modifications made to this ma-
chine can cause serious injury. Do not undertake • If the accumulator is not functioning correctly, consult
any modifications without first consulting your CASE your CASE CONSTRUCTION Dealer. Never try to
CONSTRUCTION Dealer. Any modifications made carry out any servicing operation on the accumulator. If
must be in conformity with the technical specifications this instruction is not followed serious injury can result.
of the machine and any current safety legislation re- • The accumulator is charged with nitrogen under high
quirements. pressure. Do not weld or allow flames to come near to
• Certain components of the machine are subject to the accumulator.
type approval. When replacing such components, • There is high pressure fuel in the feed pipe when the en-
it is mandatory to make sure that they conform to gine is running and immediately after it has been shut
regulations. For safety's sake, use genuine CASE down. Wait for 2 minutes after engine shut down be-
CONSTRUCTION parts. fore you do any maintenance or inspections to allow
• Pressurized hydraulic fluid or grease which penetrates the pressure to drop in the pipe.
the skin can cause serious injury. Take the neces- • High-voltage is charged to the controller and/or to the
sary safety precautions (safety clothing and protection injector while the engine is running and immediately
for face and hands) to avoid such risks. Also, before after it has been shut down.
using these products, read the manufacturer's instruc- Do not touch the controller or the injector.
tions concerning their use. If hydraulic fluid penetrates If it is necessary to touch them for maintenance pur-
the skin, call a doctor immediately. poses, consult your CASE CONSTRUCTION Dealer.
• Coolant solution is toxic.
2-9
--- Page 6 ---
2 - SAFETY INFORMATION
Decal placement diagrams
(1) Table of safety precautions
Part number: KHP35790
KHP35790 3
(1A) Interference with attachments
The end attachment used for machine operation (e.g.
bucket, hydraulic breaker, clamshell..) may hit the cab
and/or the boom depending upon the length of the arm,
the size of the bucket or the installation of a quick coupler.
Always check the operating range of the machine with the
specific attachment in use. Avoid abrupt operation in or-
der to keep proper clearance between the attachment and
the cab or boom or other significant parts of the machine.
Collisions between attachment and cab or boom or other
significant parts of the machine can cause serious dam- KHP35790_A 4
ages.
2-19
--- Page 7 ---
2 - SAFETY INFORMATION
(33) Emergency Stop Switch operation
Part number: KHP34750
Press the top side of the switch only if an emergency stop
of the engine is necessary.
KHP34750 41
(34) Foldable handrail
Part number: KHP34730
The handrail on the top of the fuel tank shall be set and
fixed in the horizontal position before a transport opera-
tion.
Make sure to read the Operator's manual to understand
how to set the handrail according to the operating condi-
tion of the machine.
KHP34730 42
(35) Blind spot of Field View Monitior (Optional)
Part number: KHP33700
The Field View Monitor system does not ensure visibility
on the closest area around the machine.
Make sure to read the Operator's manual to understand
proper practices and precautions to be tackled for ma-
chine operation with the Field View Monitor system (Op-
tional).
KHP33700 43
(36) Global Warming Potential decal
Part number: KHP34040
Greenhouse gas: HFC-134a
Quantity (A/C system charge): 1 kg (2.2 lb)
Global Warming Potential (GWP): 1.43 Ton
Service, repair, or recharging must be performed only by
trained service technician. Always contact your local au-
thorized dealer. Failure to comply could result in death or
serious injury.
KHP34040 44
2-29
--- Page 8 ---
3 - CONTROLS AND INSTRUMENTS
Forward controls
Forward controls
WARNING
Avoid injury!
Inspect the work area or job site to make sure that machine operation can be done safely. Confirm that
the lever operation is the same as indicated on the control pattern labels. If not, immediately change
the machine control pattern or the label displayed to match the machine control pattern.
Failure to comply could result in death or serious injury.
W1339A
Selection of control pattern
The machine can be equipped with a selector valve that allows to set two different patterns of the hydraulic controls
of the front equipment. The patterns are called C and D. Refer to the next pages for description of the patterns.
NOTICE: Before starting machine operation, check that the operating pattern of control levers is consistent with the
position selected on the valve. Furthermore, check that the pattern shown on the control mapping sheet into the cab
is consistent with the operating pattern of the control levers.
To select the desired control pattern proceed as follows:
1. Lower the attachment to the ground, and stop the engine.
2. Open the storage compartment located under the cab.
3. Read and understand the warning label (L) located on the inside of the compartment cover.
SMIL17CEX0587EA 1
4. Pull the locking knob (1) and move the lever (2) to set the desired control pattern C or D. Release the locking knob.
SMIL17CEX0588EA 2
5. Close the storage compartment.
3-7
--- Page 9 ---
3 - CONTROLS AND INSTRUMENTS
Ventilation
These push buttons (4) enable the air flow to be increased
or reduced. To increase the flow of air, press the top but-
ton. To decrease the flow of air, press the lower button.
The segments on the display screen (9) will increase or
decrease depending on the flow selected.
WSD444-001 3
Temperature
These push buttons (3) allow the temperature to be raised
or lowered within an 18 °C (64.4 °F) and 32 °C (89.6 °F).
To increase the temperature, press the up button. To
lower the temperature, press the low button. The tem-
perature reading will appear on the display screen (9).
NOTICE: The temperature reading can be displayed in
degrees Celsius or degrees Fahrenheit. To select the
scale required, press the two push buttons (3) simulta-
neously for five to ten seconds. The degrees Fahrenheit
temperature will be followed by an "F".
GG7D18-001 4
Air recycling
This button (8) allows for two different types of air circula-
tion to be selected. Fresh air from outside or recycled air
from inside. The type of circulation will be changed each
time the button is pressed. Indication of the type of flow
direction selected will appear on the display screen (9).
(A) Internal air circulated
(B) External air enters
3FGJSW-001 5
Air flow direction
This button (7) allows four different types of air flow direc-
tion to be selected. To select the type of air flow direction,
press the button (7) successively until the type of flow di-
rection required is obtained. Indication of the type of flow
direction selected will appear on the display screen (9).
V85W49-001 6
3-17
--- Page 10 ---
3 - CONTROLS AND INSTRUMENTS
Control buttons
SMIL15CEXY842FA 2
1. Travel mode selector button
2. Wiper button
3. Display mode selector button
4. SCR CLEANING button
5. Windshield washer button
6. Working lights button
7. Camera view selector button (*)
8. Attachment selector button
9. Idle mode button
0. Hour meter button
(*) The camera view selector button is active only if the Field View Monitor system is equipped. Refer to Chapter 9.
3-27
--- Page 11 ---
3 - CONTROLS AND INSTRUMENTS
Wiper button
The wiper operation cycles as follows every time the wiper
button is pressed.
Slow speed
• from inactive wiper, the wiper is activated and moves at
slow speed
Fast speed
• from wiper moving at slow speed, the wiper goes mov-
ing at fast speed
Stop
• from wiper moving at fast speed, the wiper is stopped.
The wiper speed is indicated by a specific icon on the
display:
The wiper is active at slow speed.
The wiper is active at fast speed.
SMIL15CEXY886BB 12
The wiper can be intermittently operated by pressing and
holding down the one-touch wiper button on the back of
the right control lever.
NOTICE: do not operate the wiper when the windshield is
dry. The wiper may crack.
NOTICE: if the wiper is operated when the glass is cov-
ered with mud or snow, the wiper may be damaged.
SMIL20CEX0009AA 13
3-37
--- Page 12 ---
3 - CONTROLS AND INSTRUMENTS
Machine status
Detailed machine conditions can be
checked.
The following items can be checked:
page Machine information
ENGINE SPEED (min-1)
P1 PRESS. (MPa)
P2 PRESS. (MPa)
1/3
BATTERY VOLT. (V)
ENGINE PROTECTION FEATURE
ALTITUDE COMPENSATION SMIL15CEX0456AA 30
ACCUMULATED FUEL
CONSUMPTION (L)
ACCUMULATED DEF CONSUMP-
2/3
TION (L)
COOLING DOWN REMAINING TIME
(sec)
ENGINE OPERATION TIME (hr)
MACHINE OPERATION TIME (hr)
SWING OPERATION TIME (hr)
3/3
TRAVEL OPERATION TIME (hr)
BREAKER OPERATION TIME (hr)
CRUSHER OPERATION TIME (hr)
NOTE: press and hold the left and right buttons together
for 10 s, and the entire fuel history will be reset.
Engine protection feature: the machine monitors its en-
gine operation and, in case excessive load is applied, con-
trols the engine output for protection. "++++" indicates
that this function has been activated, "----", not activated.
Altitude compensation: the machine is equipped with
barometric sensor and, under the condition of extremely
low atmospheric pressure (ex. high altitude area), op-
timize the engine operation. "++++" indicates that this
function has been activated, "----", not activated.
3-47
--- Page 13 ---
3 - CONTROLS AND INSTRUMENTS
Overhead controls
Roof curtain
To open the roof curtain, slide it toward the rear using the
handles. To close the curtain slide it toward the front.
VHIVJ6-001A 1
Roof hatch
To open the roof hatch, push the two locking levers (1) to
the inside, and follow the opening movement by holding
the handle (2).
NOTICE: The roof hatch is fitted with two gas struts, and
the opening movement shall thus be followed through by
hand in order not to damage the machine.
To close the roof hatch, pull it down until the two locking
levers (1) are engaged.
SMIL17CEX0898AA 1
Sun shield (optional)
The sun shield is fixed to the windshield and can easily be
positioned as required.
R566HK-001A 1
3-57
--- Page 14 ---
3 - CONTROLS AND INSTRUMENTS
Cameras
The external cameras, along with the external mirrors, en-
sure proper visibility around the machine during operation.
A rear camera (1) is installed on the counterweight. A
right-side camera (2) is installed on the fuel tank.
SMIL17CEX0204AA 1
The view of the rear camera (R) is shown on the left side
of the display. The view of the right side camera (S) is
shown on the right side of the display.
NOTICE: Never operate the machine while only looking
at the images on the display. Make sure to check the
area around the machine by the direct view or through
the mirrors.
NOTICE: If any mud, raindrops, snow, etc. are adhered
to the camera lens, the images on the display are deteri-
orated. Wipe away dirt with a wet and soft cloth, and then
wipe it with a dry and soft cloth. Make sure not to scratch
the cameras.
SMIL16CEX1248AA 2
If the cameras or the camera wirings have a failure, a
warning buzzer sounds for about 5 s, the CHECK CAM-
ERA message (1) and a DTC (3) appear, and the camera
failure icon (2) is displayed. Moreover, the image of the
failed camera is replaced by a grey background.
SMIL16CEX1075AA 3
3-67
--- Page 15 ---
3 - CONTROLS AND INSTRUMENTS
Fuel tank
WARNING
Fire hazard!
When handling diesel fuel, observe the following precautions:
1. Do not smoke.
2. Never fill the tank when the engine is running.
3. Wipe up spilled fuel immediately.
Failure to comply could result in death or serious injury.
W0099A
Fill the fuel tank with Ultra-Low Sulfur diesel fuel only. Refer to Chapter 6 for the detailed specifications and prescrip-
tions about the fuel to be used.
NOTICE: Never put any moisture elimination product (water draining agent) in the fuel tank. Doing so may damage
the fuel system, and thus the engine.
NOTICE: If the machine is operated in cold climate, fill the fuel tank at the end of each working day to prevent the
formation of condensation.
To refill the fuel tank proceed as follows:
1. Stop the engine, and remove the starter key.
2. Get over the fuel tank. Clean the area around the fuel
filler neck (1).
3. Slide the protective plate over the cap (2) of the fuel
filler neck, and unlock the cap with the starter key.
4. Turn the cap (2) counterclockwise and open the filler
neck.
NOTICE: Never remove the mesh filter inside the fuel
filler neck. Doing so may damage the fuel system, and
thus the engine.
SMIL17CEX0589AA 1
5. Refill until the needle indicator (3) gets up from the filler
neck.
6. Put the cap (2) on the filler neck. Turn the cap clock-
wise until it engages the stopper on the filler neck.
7. Lock the cap (2) with the starter key.
SMIL19CEX2660AA 2
3-77
--- Page 16 ---
3 - CONTROLS AND INSTRUMENTS
The MANUAL SCR CLEANING is stopped if any of the following is done:
• The operator sets the gate lock lever to unlock position.
• The operator changes the engine speed throttle position.
• The operator presses the SCR CLEANING button.
The SCR CLEANING icon starts to flash in orange and the message PUSH SCR SWITCH TO ACTIVATE is displayed.
NOTICE: Never restart normal machine operation with the MANUAL SCR CLEANING process being suspended. The
SCR system will be damaged. Resume the MANUAL SCR CLEANING process immediately.
The MANUAL SCR CLEANING is disabled if any of the following occurs:
• The MANUAL SCR CLEANING process is not completed within 40 min after it is started.
• The MANUAL SCR CLEANING is not started within 10 h after the message to request MANUAL SCR CLEANING
(PUSH SCR SWITCH TO ACTIVATE) is displayed.
A warning alarm sounds for approximately 2 s and the SCR CLEANING icon turns red. The message CHECK EN-
GINE and a DTC (Diagnostic Trouble Code) appear on the display. Immediately stop machine operation, and contact
the CASE CONSTRUCTION dealer for machine repair.
MANUAL SCR CLEANING ONLY function
The purpose of this function is to avoid high temperature
exhaust in specific operating conditions:
• Operation inside building.
• Operation underground.
• Operation near combustibles or explosives.
To enable the function, set MANUAL SCR CLEANING
ONLY to ON in the SCR CONFIGURATION tab of the user
information mode.
SMIL14CEX4935AA 8
Resuming the operating mode of the display, the SCR
CLEANING icon appears green and slashed.
NOTE: This function is just suspending AUTO SCR
CLEANING that occurs every 30 h. The system will
request MANUAL SCR CLEANING if AUTO SCR CLEAN-
ING is suspended for 8 h. Use this function only when it
is necessary to avoid AUTO SCR CLEANING for safety
purpose.
SMIL16CEX0706AA 9
3-87
--- Page 17 ---
4 - OPERATING INSTRUCTIONS
4 - OPERATING INSTRUCTIONS###_4_###
Starting the unit
Anti-theft protection
A security function can be set up in order to prevent an undesired usage of the machine, or even the theft of the ma-
chine. The security function locks the display by a password when the machine is started. Furthermore, the security
function limits the machine functionality as the engine is started without entering the password.
The set up of the security function is indicated by a specific icon on the display:
The security function is set up.
To set up the security function and the password, consult the CASE CONSTRUCTION dealer.
NOTICE: Consult the CASE CONSTRUCTION dealer in case of forgotten password.
Activation of the security function
Turning the starter key to OFF position, the option for ac-
tivating the security function is displayed. Press the right
button to activate the security function.
At the next machine start, the request for entering the
password will be displayed.
SMIL14CEX2877AA 1
As the key is turned to ON position, the request for enter-
ing the password is displayed. Enter the password using
the buttons on the cluster as a numeric keypad.
As the password is properly entered, the display is un-
locked, and the machine can be started.
If the password is wrongly entered for 3 times, or if the
engine is started up without entering the password, the
machine goes into an immobilized state:
1. A warning buzzer, and the travel alarm if equipped,
sound continuously.
2. The engine speed is limited to low idle.
SMIL14CEX2878AA 2
3. The swing function is disabled.
4. If any lever or pedal is operated, the engine stops au-
tomatically.
4-1
--- Page 18 ---
4 - OPERATING INSTRUCTIONS
3. Slowly operate the control levers to lower the attach-
ment to the ground.
SMIL17CEX0109AA 3
4-11
--- Page 20 ---
4 - OPERATING INSTRUCTIONS