PDF Operator's Manual Case 586H 588H Rough Terrain Forklift - 5 MB

This operator's manual is for the Case 586H and 588H Tier 4B (Final) Rough Terrain Forklifts.

It contains essential information on daily inspections, controls, and safe operating practices.

Adherence to the guidelines in this manual is crucial for ensuring the safety of the operator and those on the job site.

This is a key document for getting the most out of your high-performance forklift.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
586H
                   588H
        Tier 4B (final)
    Rough Terrain Forklift


OPERATOR’S MANUAL


           Part number 47780077
                    1st edition English
                        October 2014

--- Page 3 ---
1 - GENERAL INFORMATION


Front drive axle
PIN


                                             RAPH12FRK0276AA   8


Forklift mast
PIN


                                             RAPH12FRK0225AA   9


                             1-5

--- Page 4 ---
2 - SAFETY INFORMATION


2 - SAFETY INFORMATION###_2_###
Safety rules and signal word definitions

Personal safety


                  This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
                  safety messages that follow this symbol to avoid possible death or injury.


Throughout this manual and on machine safety signs, you will find the signal words DANGER, WARNING, and CAU-
TION followed by special instructions. These precautions are intended for the personal safety of you and those
working with you.


Read and understand all the safety messages in this manual before you operate or service the machine.


    DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury. The color
associated with DANGER is RED.


    WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury. The color
associated with WARNING is ORANGE.


    CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury. The
color associated with CAUTION is YELLOW.


FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.

Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine damage or property damage. The
color associated with Notice is BLUE.

Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine dam-
age or property damage. The word Notice is used to address practices not related to personal safety.

Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.

Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.


                                                          2-1

--- Page 5 ---
2 - SAFETY INFORMATION


Fuel handling precautions


• Do not smoke or permit open flames while fueling or          turer's approved cap. Use of a non-approved cap with-
  near fueling operations.                                     out proper venting may result in pressurization of the
                                                               tank.
• Do not fill the fuel tank completely to the top. Allow
  room for expansion.                                       • Never use fuel for cleaning purposes.
• Clean up spilled fuel immediately and dispose of con-     • Use the correct fuel grade for the operating season.
  taminated material in an environmentally correct man-       Use ultra-low sulfur diesel fuel only.
  ner.
• Tighten the fuel tank cap securely. Should the fuel
  cap be lost, replace it only with the original manufac-


                                                        2-11

--- Page 6 ---
2 - SAFETY INFORMATION


(7) Warning. Fuel under pressure.
                    WARNING
  Pressurized System Hazard. Do not open high
 pressure fuel system with engine running. Engine
  operation causes high fuel pressure. Failure to
   comply could result in death or serious injury.

                   Quantity: 2
                English 87581010
                Spanish 87622505
                                                                    87581010   16
            French Canadian 87622506


NOTE: Open both of the engine side panels.
                                                                 RAPH12FRK0174AA    17
(7) Location:
On top of the frame rail.


                                                                 RAPH12FRK0154AA    18


                                                 2-21

--- Page 7 ---
3 - CONTROLS AND INSTRUMENTS


FORWARD CONTROLS

Console controls
Function switches (left side)
(1) Horn switch
            Push the horn symbol on the rocker switch
            to sound the horn.


(2) Blank


(3) Rear work lamp switch
            Push the rear work lamp symbol on the
            switch to turn on the rear work lamps. Push
            the other side to turn off the rear work lamps.


(4) Driving lamp switch
            Push the driving lamp symbol on the switch                  RAPH12FRK0138AA   1
            to turn on the driving lamps. Push the other
            side to turn off the driving lamps.


(5) Flasher switch
            Push the flasher symbol switch and the front
            and rear signal lamps flash simultaneously.
            Push the other side of the flasher switch to
            turn off the signal lamps.

(6) Turn signal switch (three position switch)
            Push the left side of the switch to signal a
            left turn. Push the right side of the switch to
            signal a right turn. Place the switch in the
            center position to turn off the turn signal.


                                                              3-3

--- Page 8 ---
3 - CONTROLS AND INSTRUMENTS


Overview of the SETUP menu


                                                  RAIL14FRK0001GA   3


                 (1) Top level menu                                          (2) Second level menu
SETUP   Setup the start of the top level menus              HOUR        Engine work hours
EXIT    Exit the setup menu                                 RPM         Engine RPM
DSPLY   Alternate between desired display options           COOLT       Engine coolant temperature
UNITS   Alternate between desired temperature units         TRANT       Transmission oil temperature
        (degrees F or C)
JTIME   Job timer (track hours for a specific job)          CYCLE       Cycle through each option listed under the
                                                                        DSPLY menu
DPF     Diesel Particulate Filter (inhibit auto             FAHR        Display temperatures in degrees Fahrenheit
        regeneration)
OIL     Oil life reset                                      CELC        Display temperatures in degrees Celsius
                                                            (3)         Total work hours appear for the current job
                                                                        timer
                                                            RESET       Reset the job timer work hours or oil life
                                                            INHIB       Inhibit the auto-regeneration process
                                                            ALLOW       Allow the auto-regeneration process


                                                        3-13

--- Page 9 ---
4 - OPERATING INSTRUCTIONS


• Do not wait longer than 30 s after the engine preheat lamp is not lit before cranking the engine. If the delay is longer,
  the start up cycle is aborted and the process must be restarted.

Warm up the hydraulic system
When the temperature is below 4 °C (40 °F) and the engine has been warmed up:
1. Raise the engine throttle between 1600 - 1800 RPM.
2. Drive the machine slowly in a low gear.
3. Actuate each of the hydraulic forklift controls.
   NOTE: Watch the hydraulic malfunction indicator lamp. If the oil is too cold the lamp will illuminate while the
   operator cycles the functions.
4. Cycle the functions for approximately 10 min.
5. Release the controls and leave the machine throttle set for approximately 15 s.
NOTE: Immediately after the warm up procedure, the machine may operate a bit slower than normal, but will quickly
return to normal operating speeds.


                                                           4-5

--- Page 10 ---
4 - OPERATING INSTRUCTIONS


Four-Wheel Drive (4WD) machine
If equipped, Four-Wheel Drive (4WD) significantly improves traction in rough conditions. When the rear steer axle is
engaged, operate the machine only in 1st or 2nd gear. Disengage the rear steer axle before operating on the hard
surface or in 3rd or 4th gear.
NOTICE: The use of 4WD when it is not required will increase the wear on machine components and affect the
machines mobility in certain driving situations.
NOTE: 4WD can be engaged when the machine is on the move or at a stop.
Engage or Disengage 4WD:
1. Press the 4WD symbol end of the rocker switch to
   engage 4WD system. The 4WD symbol illuminates
   when 4WD is engaged.
2. Press the other side of the 4WD switch to disengage.


                                                                                RAPH12FRK0139AA   1


                                                       4-15

--- Page 11 ---
6 - WORKING OPERATIONS


586H Load limit chart
The lift capacity decreases as the load center distance to the front of the fork face increases.
NOTE: Machine capacity is less when operating on uneven, unstable, or soft ground conditions. Lift capacities are
based on solid, level, and smooth ground conditions. Reduce the load to maintain stability.


                                                     RAIL12FRK1107GA   3
                               Lift capacity chart as load center distance increase

                The load center distance (B) from the fork face            Approximate maximum load limit (A)
(1)             0 - 610 mm (0 - 24 in)                                     2722 kg (6000 lb)
(2)             711 mm (28 in)                                             2359 kg (5200 lb)
(3)             813 mm (32 in)                                             2041 kg (4500 lb)
(4)             914 mm (36 in)                                             1769 kg (3900 lb)
(5)             1016 mm (40 in)                                            1633 kg (3600 lb)


                                                            6-5

--- Page 12 ---
7 - MAINTENANCE


Welding on the machine
Contact your dealer if you have any questions before welding on this machine. The following procedures must be
completed before welding.
1. Remove the battery cover and disconnect the batter-
   ies.


                                                                            RAPH12FRK0277AA   1

2. Disconnect the alternator terminal wires.


                                                                            RAPH12FRK0163AA   2

3. Remove the four bolts and the ECU cover panel from
   the right-hand side of the operator seat.


                                                                            RAPH12FRK0242AA   3


                                                     7-7

--- Page 14 ---
7 - MAINTENANCE


Fluid capacities and lubricant specifications
Engine crank case
Specification:                           TUTELA UNITEK CJ-4 ENGINE OIL SAE 10W-40( API CJ-4)
Capacity:
With filter change                       8.00 L (8.45 US qt)

NOTE: Refer to the “Engine oil viscosity” 7-22 for recommendations on the oil types designed for your operating
environment.

Fuel tank
Specification:                           ASTM D975 GRADE NO. 2-D S15
Capacity:                                117 L (31 US gal)

Cooling system
Specification:                           CASE AKCELA ACTIFULL™ OT EXTENDED LIFE COOLANT
Capacity:                                17.4 L (18.4 US qt)

Hydraulic system
Specification:                           CASE AKCELA HY-TRAN® ULTRACTION
Capacity:
Total system                             70.0 L (74.0 US qt)
Reservoir with filter change             54.5 L (57.6 US qt)
Reservoir without filter change          52.6 L (55.6 US qt)

Transmission
Specification:                           CASE AKCELA HY-TRAN® ULTRACTION
Capacity:
Manual (Power shuttle)
                                         Two-Wheel Drive (2WD)     Four-Wheel Drive (4WD)
Total system                             17.0 L (18.0 US qt)       19.4 L (20.5 US qt)
Refill (with or without filter change)   10.5 L (11.1 US qt)       13.0 L (13.7 US qt)

Front drive axle
Specification:                           TUTELA TRANSAXLE FLUID SAE 80W-140
Capacity:
Differential and planetaries             13.6 L (14.4 US qt)

Rear steer axle — Four-Wheel Drive (4WD)
Specification:                           TUTELA TRANSAXLE FLUID SAE 80W-140
Capacity:
Differential                             5.5 L (5.8 US qt)
Each planetary hub                       0.7 L (0.7 US qt)

Brake master cylinder
Brake fluid supplied by the transmission.


                                                         7-17

--- Page 15 ---
7 - MAINTENANCE


At warning message display

Engine air filters
Clean or replace the engine air filter when the warning lamp     and engine malfunction lamp   remains illuminated
while the engine is running.

1. Clean the air pre-cleaner (if equipped):
    A. Remove the wing nut (1).
    B. Remove the cover (2).
    C. Remove the bowl (3).
    D. Clean the bowl with a damp cloth.
    E. Assemble the air pre-cleaner.
2. Open the right-hand side engine panel.


                                                                                                    RAPH12FRK0030BA    1

3. Clean the area around the outside front cover of the air
   filter housing.
4. Inspect the air filter housing and components for dam-
   age.
5. Release the three clips that secure the air filter housing
   cover in place.


                                                                                                     RAIL14FRK0020BA   2


                                                          7-27

--- Page 16 ---
7 - MAINTENANCE


3. Wait for         to appear on the display (1). The sys-
   tem is checking that the machine is in an idle state with
   the park brake is on.

4. The                                    sequence mes-
   sage appears on the display screen when the system
   is ready to start the regeneration process.
5. Press the start button (2).

6.                   message alternates on the display
     screen while the system validates all conditions are
     met.
7. One of the following will occur.

     •                   will alternate on the display screen,
         the regeneration process starts.

     •                   will alternate on the display screen,
         the machine is not ready. Repeat Step 2.
NOTE: If the regeneration continues to FAIL, contact your
authorized dealer for service.

8.                   will alternate on the display screen and
     return to the main screen. The regeneration process is
     complete and the machine is ready for operation.


                                                                                                    RAIL12FRK1123CA   2


After Treatment System (ATS) regeneration failure
NOTE: There are two levels of warning if the operator does not perform the manual regeneration or a system mal-
function occurs. Level 1 warning is provided when the Particulate Matter (PM) Catalyst reaches maximum load at
which time the engine power is reduced by 25 %. Level 2 warning is provided when the PM Catalyst is overloaded at
which time the engine power is reduced by 50 %..
     When the below messages appear during machine op-
     eration the Engine Control Unit (ECU) will begin to
     de-rate the engine output, contact your dealer for ser-
     vice..
     • Level 1 — A single audible alert, an illuminated op-
       erator alert symbol ,         and           alternate
       on the display screen.
     • Level 2 — A constant audible alert, an illuminated
       emergency stop symbol       ,      and          al-
       ternate on the display screen.


                                                           7-37

--- Page 17 ---
7 - MAINTENANCE


Coolant reservoir (de-aeration reservoir) fluid level
    CAUTION
   Burn hazard!
   Hot coolant can spray out if you remove the filler cap while the system is hot. After the system has
   cooled, turn the filler cap to the first notch and wait for all pressure to release before proceeding.
   Failure to comply could result in minor or moderate injury.
                                                                                                                C0043A


NOTICE: NEVER mix OAT coolant with conventional coolant. Under no circumstances should you top off a cooling
system with only water. You can use a refractometer to check the concentration level. Supplemental Coolant Additives
(SCA) should not be used when using CASE AKCELA ACTIFULL™ OT EXTENDED LIFE COOLANT. Change the
coolant solution at the change interval recommended.
Check the de-aeration reservoir fluid level every 50 h of operation.
Coolant fluid specification – CASE AKCELA ACTIFULL™ OT EXTENDED LIFE COOLANT

1. Ensure an accurate level reading:
    A. Park the machine on level ground.
    B. Shut down the engine.
    C. Allow time for the coolant to completely cool.
       Coolant must be cold before proceeding.
    D. Open the right hand side engine panel.
2. Check the coolant level on the reservoir. The coolant
   level should be between the HOT MAX mark (1) and
   the COLD MIN mark (2).
3. If coolant is below the COLD MIN mark add coolant.


                                                                                                      RAPH12FRK0034BA    1


                                                        7-47

--- Page 18 ---
7 - MAINTENANCE


Fuel filters
Replace the fuel filters after the first 100 h of operation on a new machine or if a major component has been rebuilt.
Then replace the fuel filters every 500 h of operation or after a loss of engine power.

1. Fill the fuel tank before proceeding.
2. Open the fuel tank cap slightly to release pressure.
3. Open the right side engine panel.
4. Clean the area around the water separator of dirt and
   debris.


                                                                                                        RAPH12FRK0180AA   1

5. Remove the wire connector at the base of the water
   separator.


                                                                                                        RAPH12FRK0249AA   2

   • Press on the wire clasp that holds the connector to
     the drain to remove.
NOTE: View is from underneath the machine.


                                                                                                        RCPH10TLB031AAF   3


                                                          7-57

--- Page 19 ---
7 - MAINTENANCE


Front drive axle - drive shaft
Grease the front drive shaft every 250 h of operation. Use
TUTELA MULTI -PURPOSE EP GREASE 251H, GR-9.


                                                                  RAPH12FRK0258AA   1


                                                       7-67

--- Page 20 ---
7 - MAINTENANCE


Tilt cylinder - Grease
Grease the tilt cylinders (four locations) every 250 h of op-
eration. Use TUTELA MULTI -PURPOSE EP GREASE 251H,
GR-9.
NOTE: All views are from underneath the machine.


                                                                    RAPH12FRK0267AA   1


                                                                    RAPH12FRK0268AA   2


                                                                    RAPH12FRK0265AA   3


                                                                    RAPH12FRK0266AA   4


                                                          7-77

--- Page 21 ---
7 - MAINTENANCE


Every 1000 hours

Hydraulic fluid and filter
     WARNING
    Personal Protective Equipment (PPE) required.
    When assembling, operating, or servicing the machine, wear protective clothing and PPE necessary
    for the particular procedure. Some PPE that may be necessary includes protective shoes, eye and/or
    face protection, hard hat, heavy gloves, filter mask, and hearing protection.
    Failure to comply could result in death or serious injury.
                                                                                                       W0353A


     WARNING
    Burn hazard!
    Before performing any service on the hydraulic system, you must allow it to cool. Hydraulic fluid
    temperature should not exceed 40 °C (104 °F).
    Failure to comply could result in death or serious injury.
                                                                                                       W0241A


Replace the hydraulic fluid and oil filter every 1000 h of operation.
Hydraulic oil specification – 54.5 L (57.6 US qt) of CASE AKCELA HY-TRAN® ULTRACTION.

1. Warm up the hydraulic fluid by operating the forklift con-
   trols.
2. Park the machine on level ground.
3. Lower the carriage to the ground and turn off the en-
   gine.
4. Place a suitable container underneath the hydraulic
   reservoir drain plug.
5. Remove the hydraulic fill cap.
6. Remove the drain plug.


                                                                                             RAPH12FRK0219AA    1

7. Remove the hydraulic filter:
    A. Locate the hydraulic filter under the right front por-
       tion of the machine just behind the front drive axle.
    B. Clean the area around the filter head area before
       removing the old filter.
    C. Use a filter wrench and remove the old filter. Have
       a suitable container ready to capture any fluid that
       might leak or spill.
    D. Dispose of the filter in accordance with local, re-
       gional, and federal regulations.

                                                                                             RCPH10TLB045AAF    2


                                                          7-87

--- Page 22 ---
7 - MAINTENANCE


13. Position the filter cover over the housing, hold the
    cover in place, and fasten the clips that secure the air
    filter cover in place.


                                                                   RAIL14FRK0018BA   7


                                                         7-97

--- Page 23 ---
7 - MAINTENANCE


Engine air pre-cleaner (if equipped)
Check the air pre-cleaner bowl and remove any debris from the bowl.

1. Remove the wing nut (1) .
2. Remove the cover (2) and bowl (3) .
3. Empty debris from the bowl and wipe with a damp cloth.
4. Assemble the air pre-cleaner.


                                                                      RAPH12FRK0030BA   1


                                                      7-107

--- Page 24 ---
8 - SPECIFICATIONS


8 - SPECIFICATIONS###_9_###
Engine - General specification
586H and 588H
Model                                         Diesel, F5HFL463D*F005, TIER 4B Final emissions
                                              compliant
Type                                          Four cylinder, turbocharged
Firing order                                  1-3-4-2
Bore and stroke                               99 mm x 110 mm ( 3.90 in x 4.33 in)
Displacement                                  3.4 l (207.5 in³)
Compression ratio                             17 to 1
Fuel injection                                Direct High Pressure Common Rail (HPCR)
Horsepower - rated at 2200 RPM
       Gross                                  55 kW (75 Hp)
       Net with 33 ° fan                      51 kW (69 Hp)
Peak torque at 1400 RPM
       Gross                                  316 N·m (233 lb ft)
       Net with 33 ° fan                      298 N·m (220 lb ft)
       Maximum torque rise                    35 % ± 5 RPM
Engine speeds
       Rated speed, full load                 2200 RPM
       Low idle                               900 - 1000 RPM
       High idle, no load                     2330 - 2430 RPM
       Converter stall                        1925 - 2075 RPM
       Hydraulic stall                        2175 - 2330 RPM


                                        8-1

--- Page 25 ---
8 - SPECIFICATIONS


Torque
Use the torques in this chart when special torques are not given. These torques apply to fasteners with both UNC
and UNF threads as received from suppliers dry, or when lubricated with engine oil. Not applicable if special graphite
lubricants, Molydisulfide greases, or other extreme pressure lubricants are used.

Decimal hardware
Grade 5 bolts, nuts, and studs
                 Size                                    Nm                                  lb in/lb ft
1/4 in                                 12 - 15 Nm                              108 - 132 lb in
5/16 in                                23 - 28 Nm                              204 - 252 lb in
3/8 in                                 48 - 57 Nm                              420 - 504 lb in
7/16 in                                73 - 87 Nm                              54 - 64 lb ft
1/2 in                                 109 - 130 Nm                            80 - 96 lb ft
9/16 in                                149 - 179 Nm                            110 - 132 lb ft
5/8 in                                 203 - 244 Nm                            150 - 180 lb ft
3/4 in                                 366 - 439 Nm                            270 - 324 lb ft
7/8 in                                 542 - 651 Nm                            400 - 480 lb ft
1 in                                   787 - 944 Nm                            580 - 696 lb ft
1-1/8 in                               1085 - 1193 Nm                          800 - 880 lb ft
1-1/4 in                               1519 - 1681 Nm                          1120 - 1240 lb ft
1-3/8 in                               1980 - 2278 Nm                          1460 - 1680 lb ft
1-1/2 in                               2631 - 2983 Nm                          1940 - 2200 lb ft
                                          Markings for Grade 5 hardware


Grade 8 bolts, nuts, and studs
                 Size                                  Nm                                    lb in/lb ft
1/4 in                                 16 - 20 Nm                             144 - 180 lb in
5/16 in                                33 - 39 Nm                             288 - 348 lb in
3/8 in                                 61 - 73 Nm                             540 - 648 lb in
7/16 in                                95 - 114 Nm                            70 - 84 lb ft
1/2 in                                 149 - 179 Nm                           110 - 132 lb ft
9/16 in                                217 - 260 Nm                           160 - 192 lb ft
5/8 in                                 298 - 358 Nm                           220 - 264 lb ft
3/4 in                                 515 - 618 Nm                           380 - 456 lb ft
7/8 in                                 814 - 976 Nm                           600 - 720 lb ft
1 in                                   1220 - 1465 Nm                         900 - 1080 lb ft
1-1/8 in                               1736 - 1953 Nm                         1280 - 1440 lb ft
1-1/4 in                               2468 - 2712 Nm                         1820 - 2000 lb ft
1-3/8 in                               3227 - 3688 Nm                         2380 - 2720 lb ft
1-1/2 in                               4285 - 4827 Nm                         3160 - 3560 lb ft
                                          Markings for Grade 8 hardware


NOTE: Use thick nuts with Grade 8 bolts.


                                                        8-11

View the complete manual on HeyDownloads →