PDF Operator Manual Hyundai R330LC-9A Crawler Excavator - 2 MB

This is the official operator's manual for the Hyundai R330LC-9A Crawler Excavator.

It contains everything an operator needs to know for safe and efficient machine use, including control layouts, safety warnings, and daily maintenance checks.

Following the procedures in this manual will help maximize productivity and extend the life of your excavator.

It is a vital document for every operator.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
CONTENTS

Foreword ----------------------------------------------------------- 0-1       6. Traveling of the machine ----------------------------- 4-13
Before servicing this machine --------------------------- 0-2                  7. Efficient working method ---------------------------- 4-16
EC regulation approved ------------------------------------ 0-3                8. Operation in the special work sites ------------- 4-20
Table to enter S/No and distribution --------------------- 0-4                 9. Normal operation of excavator ------------------- 4-22
Safety labels ------------------------------------------------------ 0-5     10. Attachment lowering ----------------------------------- 4-23
Machine data plate -------------------------------------------- 0-19         11. Storage -------------------------------------------------- ----- 4-24
Guide (direction, S/No, symbol) ------------------------ 0-20                12. RCV lever operating pattern ----------------------- 4-26
                                                                             13. Switching hydraulic attachment circuit -------- 4-28
SAFETY HINTS                                                                 14. Regeneration system ------------------------------------ 4-29
  1. Before operating the machine -------------------- 1-1
  2. During operating the machine -------------------- 1-16                  TRANSPORTATION
  3. During maintenance ----------------------------------- 1-23               1. Preparation for transportation -------------------- 5-1
  4. Parking -------------------------------------------------------- 1-26     2. Dimension and weight ------------------------------- 5-2
                                                                               3. Loading the machine --------------------------------- 5-5
SPECIFICATIONS                                                                 4. Fixing the machine ------------------------------------ 5-7
  1. Major components ------------------------------------- 2-1                5. Loading and unloading by crane ---------------- 5-8
  2. Specifications -------------------------------------------- 2-2
  3. Working range ------------------------------------------- 2-5           MAINTENANCE
  4. Weight ------------------------------------------------------- 2-7        1. Instruction -------------------------------------------------    6-1
  5. Lifting capacities ---------------------------------------- 2-9           2. Tightening torque --------------------------------------- 6-6
  6. Bucket selection guide ------------------------------- 2-12               3. Fuel, coolant and lubricants ----------------------- 6-9
  7. Undercarriage ------------------------------------------- 2-14            4. Maintenance check list ------------------------------ 6-11
  8. Specification for major components ----------- 2-16                       5. Maintenance chart ------------------------------------ 6-16
  9. Recommended oils ------------------------------------ 2-20                6. Service instruction ------------------------------------- 6-18
                                                                               7. Electrical system --------------------------------------- 6-44
CONTROL DEVICES                                                                8. Air conditioner and heater -------------------------- 6-47
  1. Cab devices ----------------------------------------------- 3-1
  2. Cluster ------------------------------------------------------- 3-2     TROUBLESHOOTING GUIDE
  3. Switches ---------------------------------------------------- 3-27        1. Engine -------------------------------------------------- ----   7-1
  4. Levers and pedals ------------------------------------- 3-32              2. Electrical system --------------------------------------- 7-2
  5. Air conditioner and heater ------------------------- 3-34                 3. Others ------------------------------------------------------- 7-3
  6. Others -------------------------------------------------------- 3-38
                                                                             HYDRAULIC BREAKER AND QUICK CLAMP
OPERATION                                                                      1. Selecting hydraulic breaker ------------------------ 8-1
  1. Suggestion for new machine ---------------------- 4-1                     2. Circuit configuration ----------------------------------- 8-2
  2. Check before starting the engine --------------- 4-2                      3. Maintenance --------------------------------------------- 8-3
  3. Starting and stop the engine ---------------------- 4-3                   4. Precaution while operating the breaker ------ 8-4
  4. Mode selection system ------------------------------ 4-7                  5. Quick clamp ---------------------------------------------- 8-6
  5. Operation of the working device ----------------- 4-12                  INDEX ------------------------------------------------------------ 9-1

--- Page 5 ---
Replace damaged battery cable (s) and replace any related parts. Eliminate any fouling, which may
have caused insulation failure or related component damage or wear. Ensure that all components are
reinstalled correctly.
An exposed wire on the battery cable may cause a short ground if the exposed area comes into contact
with a grounded surface. A battery cable short produces heat from the battery current, which may be a
fire hazard.
An exposed wire on the ground cable between the battery and the disconnect switch may cause the
disconnect switch to be bypassed if the exposed area comes into contact with a grounded surface. This
action may result in an unsafe condition for servicing the machine. Repair components or replace
components before servicing the machine.
   Fire on a machine can result in personal injury or death. Exposed battery cables that come into
   contact with a grounded connection can result in fires. Replace cables and related parts that
   show signs of wear or damage. Contact your Hyundai Heavy Industries dealer.


Wiring
Check electrical wires daily. If any of the following conditions exist, replace parts before you operate the
machine.
ÂFraying
ÂSigns of abrasion or wear
ÂCracking
ÂDiscoloration
ÂCuts on insulation
ÂOther damage
Make sure that all clamps, guards, clips, and straps are reinstalled correctly. This action will help to
prevent vibration, rubbing against other parts, and excessive heat during machine operation.

Attaching electrical wiring to hoses and tubes that contain flammable fluids or combustible fluids should
be avoided.
Consult your Hyundai Heavy Industries dealer for repair or for replacement parts.
Keep wiring and electrical connections free of debris.


                                                    1-9

--- Page 6 ---
The operation on a slope is dangerous.
Avoid operating the machine on a slope of over
10 degree.


                                                        13031SH21


Operate the machine after making ground flat
when operation is required on a slope.


                                                        13031SH22


The swing on the slope can be danger of
rolling over.
Do not operate to swing the machine with the
bucket loaded on a slope since the machine
may lose its balance under such an instance.


                                                        13031SH23


Avoid parking and stopping on a slope.
Lower the bucket to the ground and block the
track when parking.


                                                        13031SH24


                                                 1-19

--- Page 7 ---
2) R330NLC-9A
   ·6.45
    6.45 m (21' 2") BOOM and 3.20 m (10' 6") ARM


                                                                   I(I')                        D
  C


                                                                                E
                                                                               G
                                                                           F


                                                                                                   H
                                                    J                                            M
                                                    K                                  N
                                         A                                                     B(L)

                                                                                                       3309A2SP03


                      Description                         Unit                  Specification
Operating weight                                         kg (lb)               32800 (72310)
Bucket capacity (SAE heaped), standard                  m3 (yd3)                 1.44 (1.88)
Overall length                               A                                 11220 (36' 10")
Overall width, with 600 mm shoe              B                                  2990 ( 9' 10")
Overall height                               C                                  3380 (11' 1")
Superstructure width                         D                                  2980 ( 9' 9")
Overall height of cab                        E                                  3090 (10' 2")
Ground clearance of counterweight            F                                  1200 ( 3' 11")
Engine cover height                          G                                 2755 ( 9' 0")
Minimum ground clearance                     H          mm (ft-in)               500 ( 1' 8")
Rear-end distance                            I                                  3504 (11' 6")
Rear-end swing radius                        I'                                 3560 (11' 8")
Distance between tumblers                    J                                  4030 (13' 3")
Undercarriage length                         K                                  4940 (16' 2")
Undercarriage width                          L                                  2990 ( 9' 10")
Track gauge                                  M                                  2390 ( 7' 10")
Track shoe width, standard                   N                                    600 (24")
Travel speed (low/high)                             km/hr (mph)                3.3/5.5 (2.1/3.4)
Swing speed                                               rpm                        9.2
Gradeability                                        Degree (%)                      35 (70)
Ground pressure (600 mm shoe)                       kgf/cm2(psi)                 0.63 (8.96)
Max traction force                                       kg (lb)               29500 (65040)


                                                  2-3

--- Page 8 ---
2) ROCK AND HEAVY DUTY BUCKET


                                                                                      Ľ1.44 m3 SAE
                      ľ1.44 m3 SAE
                                                                                      Ľ1.73 m3 SAE
                      heaped bucket
                                                                                      heaped bucket


                                                                                     Recommendation
       Capacity                     Width                                                                            6.15 m (20' 2")
                                                                               6.45 m (21' 2") boom
                                                       Weight                                                           boom
  SAE         CECE          Without         With                   2.2 m arm   2.5 m arm   3.2 m arm    4.05 m arm    2.2 m arm
 heaped       heaped       side cutter   side cutter                 (7' 3")     (8' 2")     (10' 6")     (13' 3")      (7' 3")

 ľ1.44 m3      1.25 m3     1470 mm                      1380 kg
                                             -
 (1.88 yd3)   (1.63 yd3)    (57.9")                    (3040 lb)

 Ľ1.44 m3      1.25 m3     1470 mm                      1470 kg
                                             -
 (1.88 yd3)   (1.63 yd3)    (57.9")                    (3240 lb)

 Ľ1.73 m3       1.5 m3     1710 mm                      1610 kg
                                             -
 (2.26 yd3)   (1.96 yd3)    (67.3")                    (3550 lb)

ľ: Heavy duty bucket
Ľ: Rock-Heavy duty bucket

               Applicable for materials with density of 2000 kg/m3 (3370 lb/yd3) or less
               Applicable for materials with density of 1600 kg/m3 (2700 lb/yd3) or less
               Applicable for materials with density of 1100 kg/m3 (1850 lb/yd3) or less


                                                            2-13

--- Page 9 ---
2) GAUGE
(1) Operation screen
  When you first turn starting switch ON, the operation screen will appear.
             Default                          Option                    1 Engine coolant temperature gauge
                                                                        2 Hydraulic oil temperature gauge
  4                                 2                                   3 Fuel level gauge
  1                                                                 2
                                    1                                   4 RPM / Tripmeter display
                                                                    3
  3
                                                                    4
                                                       2609A3CD13

※ Operation screen type can be set by the screen type menu of the display.
  Refer to page 3-24 for details.
(2) Engine coolant temperature gauge
                                        ① This gauge indicates the temperature of coolant.
                                          ·White range : 40-107˚C (104-225˚F)
                                          ·Red range : Above 107˚C (225˚F)
                                        ② If the indicator is in the red range or    lamp blinks in red,
                                          turn OFF the engine and check the engine cooling system.
                                        ※ If the gauge indicates the red range or        lamp blinks in
                       2609A3CD14
                                          red even though the machine is on the normal condition,
                                          check the electric device as that can be caused by the poor
                                          connection of electricity or sensor.

(3) Hydraulic oil temperature gauge
                                        ① This gauge indicates the temperature of hydraulic oil.
                                          ·White range : 40-105˚C(104-221˚F)
                                          ·Red range : Above 105˚C(221˚F)
                                        ② If the indicator is in the red range or    lamp blinks is red,
                                          reduce the load on the system. If the gauge stays in the red
                                          range, stop the machine and check the cause of the problem.
                       2609A3CD15       ※ If the gauge indicates the red range or        lamp blinks in
                                          red even though the machine is on the normal condition,
                                          check the electric device as that can be caused by the poor
                                          connection of electricity or sensor.

(4) Fuel level gauge
                                        ① This gauge indicates the amount of fuel in the fuel tank.
                                        ② Fill the fuel when the red range, or     lamp blinks in red.
                       2609A3CD16       ※ If the gauge indicates the red range or          lamp blinks in
                                          red even though the machine is on the normal condition,
                                          check the electric device as that can be caused by the poor
                                          connection of electricity or sensor.

(5) RPM / Tripmeter display
                                        ① This displays the engine speed or the tripmeter.
                                        ※ Refer to page 3-25 for details.
                   2609A3CD17


                                                    3-3

--- Page 10 ---
(3) User mode switch
                                    ① This switch is used to memorize the current machine operating
                                      status in the MCU and activate the memorized user mode.
                                      ·Memory : Push more than 2 seconds.
                                      ·Action : Push within 2 seconds.
                                      ·Cancel : Push this switch once more within 2 seconds.
                    2609A3CD27
                                    ② Refer to the page 3-15 for another set of user mode.


(4) Select switch
                                    ① This switch is used to select or change the menu and input
                                      value.
                                    ② Knob push
                                      ·Long (over 2 sec) : Return to the operation screen
                                      ·Medium (0.5~2 sec) : Return to the previous screen
                    21093CD45E
                                      ·Short (below 0.5 sec) : Select menu
                                    ③ Knob rotation
                                      This knob changes menu and input value.
                                      ·Right turning : Down direction / Increase input value
                                      ·Left turning : Up direction / Decreased input value


(5) Auto idle/ buzzer stop switch
                                    ① This switch is used to activate or cancel the auto idle function.
                                      ·Pilot lamp ON : Auto idle function is activated.
                                      ·Pilot lamp OFF : Auto idle function is cancelled.
                                    ② The buzzer sounds when the machine has a problem.
                                      In this case, push this switch and buzzer stops, but the warn-
                    2609A3CD28
                                      ing lamp blinks until the problem is cleared.


(6) Travel speed control switch
                                    ① This switch is used to select the travel speed alternatively.
                                      ·       : Low speed
                                      ·       : High speed


                    2609A3CD29


(7) Escape/Camera switch
                                    ① This switch is used to return to the previous menu or parent
                                      menu.
                                    ② In the operation screen, pushing this switch will display the
                                      view of the camera on the machine (if equipped).
                                      Please refer to page 3-25 for the camera.
                    2609A3CD30
                                    ③ If the camera is not installed, this switch is used only ESC
                                      function.

                                                3-13

--- Page 11 ---
③ Brightness and touch calibration


                  2609A3CD98A

                                                      2609A3CD160                          2609A3CD100
                                                                      Manual (1st~10th step)


                                                      2609A3CD161                          2609A3CD102
                                                                      Auto (day/night)

· If "Auto" is chosen, brightness for day and night can be differently set up. Also by using the
  bar in lower side, users can define which time interval belongs to day and night.
  (in bar figure, white area represents night time while orange shows day time)

· Touch calibration - When touch awareness goes wrong, this function use.
                      Fall in the next step if touches the middle point of cross with fingernail.
                      If touches total five points as follows, the setting is completed.


                                                     2609A3CD148


                                                                                         2609A3CD149-153


④ Unit


                  2609A3CD103

                                                      2609A3CD104                          2609A3CD124


· Temperature : ˚C ↔ ˚F
· Pressure    : bar ↔ MPa ↔ kgf/cm2
· Flow        : lpm ↔ gpm
· Date format : yy/mm/dd ↔ mm/dd/yy ↔ dd-Mar-yy


                                             3-23

--- Page 12 ---
3) SAFETY LEVER
                              (1) All control levers and pedals are disabled from operation by locating
                                  the lever to lock position as shown.
                              ※ Be sure to lower the lever to LOCK position when leaving from
   Unlock
                                  operator's seat.
                              (2) By pull lever to UNLOCK position, the machine is operational.
        Lock                  ※ Do not use the safety lever for handle when getting on or off the
               21093CD48C
                                  machine.

4) TRAVEL LEVER
                              (1) This lever is mounted on travel pedal and used for traveling by hand.
                                  The operation principle is same as the travel pedal.
                              (2) Refer to traveling of the machine in chapter 4 for details.


               21093CD48D


5) TRAVEL PEDAL
                              (1) This pedal is used to move the machine forward or backward.
                              (2) If left side pedal is pressed, left track will move.
                                  If right side pedal is pressed, right track will move.
                              (3) Refer to traveling of machine in chapter 4 for details.

               21093CD48E


6) SEAT AND CONSOLE BOX ADJUST KNOB
                     (1) This knob is used to move the seat and console box to fit the
                         contours of the operator's body.
                              (2) Pull the knob to adjust forward or backward over 150 mm (5.9").
               UP


               2609A3CD04


7) CONSOLE BOX HEIGHT ADJUST KNOB
                              (1) This knob is used to move the LH and RH control lever to fit the
                                  contours of the operator's body.
      UP
            PU
               SH             (2) The control lever can be moved upward and downward over 60 mm
                                  (2.4").


                 2609A3CD05


                                                  3-33

--- Page 14 ---
(4) Handsfree MIC
                         ① This MIC transfers user voice to receiver of the call when making a
                           call by handsfree.


             55I3CD31D


(5) Seek button
                          ① If this button pressed, the radio automatically stops at the next fre-
                            quency of broadcasting for your listening.
                          ② This button enable to select the song of the MP3 from USB.
                                   : Turn a station of higher frequency and the next song of the
             55I3CD31E               MP3.
                                   : Turn a station of lower frequency and the previous song of
                                     the MP3.

(6) Mute button
                          ① Short press this button to mute or cancel the mute (silence) while
                            broadcasting.


             55I3CD31F


(7) Mode button
                          ① Press the mode button to select the desired mode.
                          ② Radio → MP3 → AUX
                          ※ The LCD displayed each mode.

             55I3CD31G


                                           3-43

--- Page 15 ---
(8) View
     iew music info (INFO) button
                            ① Each time the INFO button is pressed, the info on the currently
                               playing song will be displayed in the following order.
                               FILE NAME → TITLE → ARTIST → ALBUM → DIR


            2209S3CD72E


(9) Scan
     can button (BSM)
                             ① While music is playing, shortly press the BSM button to scan each
                               song within the USB for 10 seconds in sequential order. (SCN)
                             ② Press and hold the BSM button to scan each song within the current
                               folder for 10 seconds in sequential order. (FOLDER SCN, however,
            2209S3CD71E        music files in the USB must be saved in folder format.)


(10) Finding and playing file (SELECT) button
      SELECT
     PUSH                      ① While USB is playing, press and hold the SELECT button for over 3
                                 seconds to enter FILE BROWER mode and search for desired files.
                               After entering FILE BROWSER mode, turn the SELECT button left/
     VOL
                             ② right to find the desired folder. After finding the folder, press the
            2209S3CD70C        SELECT button to select the folder. Turn the SELECT button left/
                               right to find the desired song and press the SELECT button to play.
                               If there are no adjustments for 3 seconds after pressing the
                             ③ SELECT button, the function will be turned off and the USB play
                               screen will be displayed.


(11) LCD display
                             ① Displays the info of the currently playing song.
                             · F-USB : Displays USB is connected to the Audio Front
                             · R-USB : Displays USB is connected to the handfree
                             · RPT : Displays that repeat function is turned on
            2209S3CD71F
                             · RPT : Displays that folder repeat function is turned on
                             · RDM : Displays that random play is turned on
                             · RDM : Displays that folder random play is turned on
                             · SCR : Displays that SCROLL is turned on


                                             3-53

--- Page 16 ---
2. CHECK BEFORE STARTING THE ENGINE

1) Look around the machine and under the machine
   to check for loosen nut or bolts, collection of dirt,
   or leakage of oil, fuel or coolant and check the        Check before
   condition of the work equipment and hydraulic             starting
   system. Check also loosen wiring, and collection
   of dust at places which reach high temperature.
ö Refer to the daily check on the chapter 6, mainte-
   nance.
2) Adjust seat to fit the contours of the operator's
   body for the pleasant operation.
                                                                          38094OP02
3) Adjust the rear view mirror.


                                                   4-2

--- Page 17 ---
5. OPERATION OF THE WORKING
                     ORKING DEVICE

ö Confirm the operation of control lever and
  working device.
1) Left control lever controls arm and swing.
2) Right control lever controls boom and bucket.                   7 6
3) When you release the control lever, control                 5      8

   lever returns to neutral position automatically.
                                                                              32
                                                                          1     4
ö When operating swing, consider the swing
  distance by inertia.


                                                                                    21094OP20


ö Left control lever
  1   Arm roll-out
                                                                                      3
  2   Arm roll-in                                          1
  3   Swing right                                                                     4
  4   Swing left
                                                                      2


                                                                                    38094OP07


ö Right control lever
  5   Boom lower                                                              6
  6   Boom raise
  7   Bucket roll-out                                  7
  8   Bucket roll-in
                                                                          5
                                                           8


                                                                                    38094OP08


                                                4-12

--- Page 18 ---
9. NORMAL OPERATION OF EXCAVATOR

Followings may occur during operation due to the
nature of a hydraulic excavator.

1) When rolling in the arm, the roll-in movement stop
   momentary at point X in the picture shown, then
   recovers speed again after passing point X.
   The reason for this phenomenon is that move-
   ment by the arm weight is faster than the speed of
   oil flow into the cylinder.
2) When lowering the boom, one may hear continu-         X
   ous sound.
   This is caused by oil flow in the valve.
3) Overloaded movement will produce sound
   caused by the relief valves, which are for the pro-
   tection of the hydraulic systems.
4) When the machine is started swing or stopped, a
   noise near the swing motor may be heard. The
                                                             38094OP18
   noise is generated when the brake valve relieves.


                                                4-22

--- Page 19 ---
(5) Boom cylinder
  Mark      Description     Unit       Specification
    L         Length      mm (ft-in)   2305 ( 7' 7")


                                                                        H
    H          Height     mm (ft-in)    276 ( 0' 11")
   W           Width      mm (ft-in)    420 ( 1' 5")                L
   Wt         Weight       kg (lb)      560 (1235)
ö Included piping.
                                                                             13035TA06


(6) Cab assembly
  Mark      Description     Unit       Specification
    L         Length      mm (ft-in)   1962 ( 6' 4")


                                                            H
    H          Height     mm (ft-in)   1686 ( 5' 6")
   W           Width      mm (ft-in)   1000 ( 3' 3")
   Wt         Weight       kg (lb)      490 (1080)              L           W


                                                                             21095TA03


(7) Counterweight
  Mark      Description     Unit       Specification
    L         Length      mm (ft-in)   2980 ( 9' 9")
                                                        H


    H          Height     mm (ft-in)   1045 ( 3' 9")
   W           Width      mm (ft-in)    590 (1' 11")
                                                                    L            W
   Wt         Weight       kg (lb)     6000 (13230)


                                                                            2507A5TR05


                                                 5-3

--- Page 20 ---
6) PERIODICAL REPLACEMENT OF SAFETY PARTS
(1) It is desirable to do periodic maintenance the
    machine for using the machine safely for a long
    time.
    However, recommend to replace regularly the
    parts related safety not only safety but maintain
    satisfied performance.
(2) These parts can cause the disaster of life and
    material as the quality changes by passing time
    and it is worn, diluted, and gets fatigued by
    using repeatedly.
    These are the parts which the operator can not
    judge the remained lifetime of them by visual
    inspection.
(3) Repair or replace if an abnormality of these
    parts is found even before the recommended
    replacement interval.
      Periodical replacement of safety parts      Interval
                        Fuel hose (tank-engine)
                                                   Every
       Engine           Heater hose               2 years
                        (heater-engine)
                        Pump suction hose
              Main                                 Every
                        Pump delivery hose
              circuit                             2 years
  Hydraulic             Swing hose
   system             Boom cylinder line hose
              Working                            Every
                      Arm cylinder line hose
              device                            2 years
                      Bucket cylinder line hose

  ö1.
    1. Replace O-ring and gasket at the same
       time when replacing the hose.
  2.
    2. Replace clamp at the same time if the
       hose clamp is cracked when checking
       and replacing the hose.


                                                    6-5

--- Page 21 ---
12) WHEN REQUIRED
    Whenever you have trouble in the machine, you must perform the service of related items, system
    by system.
                        Check items                         Service                  Page
Fuel system
·Fuel tank                                               Drain or Clean              6-29
·Prefilter                                              Clean or Replace             6-31
·Fuel filter element                                        Replace                  6-29
Engine lubrication system
·Engine oil                                                 Change                 6-18, 19
·Engine oil filter                                          Replace                6-18, 19
Engine cooling system
·Coolant                                                 Add or Change          6-21, 22, 23, 24
·Radiator                                                Clean or Flush         6-21, 22, 23, 24
·Charge air cooler                                           Check                   6-25
·Coolant filter (corrosion resistor)                        Replace                  6-20
Engine air system
·Air cleaner element                                        Replace                  6-28
Hydraulic system
·Hydraulic oil                                           Add or Change               6-34
·Return filter                                              Replace                  6-35

View the complete manual on HeyDownloads →