PDF Operator Manual Genie SX-150 SX-180 - 1 MB

This operator's manual provides comprehensive instructions for the safe operation of the Genie SX-150 and SX-180 telescopic boom lifts.

It covers all control functions, safety systems, and pre-operation inspection procedures.

Following the guidelines in this manual is crucial for ensuring the safety of the operator and anyone in the vicinity of the machine.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
Operator's Manual
              Serial Number Range


SX-150         From SX15015-101
                                    CE


SX-180         From SX18015-293


                                    with
                                    Maintenance
                                    Information


                                    Original Instructions
                                    Third Edition
                                    Second Printing
                                    Part No. 1262336

--- Page 3 ---
Third Edition • Second Printing                                     Operator's Manual


                                                               Personal Safety
Personal Safety


Personal Fall Protection
Personal fall protection equipment (PFPE) is
required when operating this machine.
Occupants must wear a safety belt or harness in
accordance with governmental regulations. Attach
the lanyard to the anchor provided in the platform.
Operators must comply with employer, job site and
governmental rules regarding the use of personal
protective equipment.
All PFPE must comply with applicable
governmental regulations, and must be inspected
and used in accordance with the PFPE
manufacturer’s instructions.


Part No. 1262336                             SX-150 • SX-180                       9

--- Page 4 ---
Third Edition • Second Printing                                                              Operator's Manual


                                                                                               Controls
Controls


Ground Control Panel
1          LCD readout screen              8 Jib boom up/down buttons          17 High speed function enable
2          Engine speed select button      9 Boom extend/retract buttons          button
3          Red Emergency Stop button       10 20A circuit breaker for system   18 Low speed function enable
                                              circuit                             button
4          Glow plug button
                                           11 Alarm                            19 Turntable rotate left button
5          Key switch for
           off/ground/platform selection   12 Bypass/recovery key switch       20 Turntable rotate right button
6          Engine start button             13 Platform rotate right button     21 Emergency power button
7          Platform level up/down          14 Platform rotate left button      22 Boom up/down buttons
           buttons                         15 Jib boom rotate right button     23 LCD screen control buttons
                                           16 Jib boom rotate left button      24 Jib rotate indicator (operating
                                                                                  envelope)


Part No. 1262336                                  SX-150 • SX-180                                             19

--- Page 5 ---
Third Edition • Second Printing                                                       Operator's Manual


                                                                                  Inspections

Pre-operation Inspection                                   Wear pads
                                                           Tires and wheels
 Be sure that the operator’s, safety and
                                                           Engine and related components
  responsibilities manuals are complete, legible
  and in the storage container located in the              Limit switches and horn
  platform.
                                                           Rotation sensors
 Be sure that all decals are legible and in place.
  See Inspections section.                                 Steer and axle sensors
 Check for hydraulic oil leaks and proper oil             Alarms and beacons (if equipped)
  level. Add oil if needed. See Maintenance
                                                           Nuts, bolts and other fasteners
  section.
                                                           Platform entry mid-rail or gate
 Check for battery fluid leaks and proper fluid
  level. Add distilled water if needed. See                Lanyard anchorage points
  Maintenance section.
                                                      Check entire machine for:
 Check for engine oil leaks and proper oil level.
  Add oil if needed. See Maintenance section.              Cracks in welds or structural components

 Check for engine coolant leaks and proper                Dents or damage to machine
  level of coolant. Add coolant if needed. See             Excessive rust, corrosion or oxidation
  Maintenance section.
                                                       Be sure that all structural and other critical
Check the following components or areas for             components are present and all associated
damage, improperly installed or missing parts and       fasteners and pins are in place and properly
unauthorized modifications:                             tightened.
     Electrical components, wiring and                After you complete your inspection, be sure
      electrical cables                                 that all compartment covers are in place and
                                                        latched.
     Hydraulic hoses, fittings, cylinders and
      manifolds
     Fuel and hydraulic tanks
     Drive and turntable motors and drive hubs


Part No. 1262336                            SX-150 • SX-180                                              29

--- Page 6 ---
Third Edition • Second Printing                                                      Operator's Manual


                                                                                Inspections
Test Drive Tilt Cutout                              91 Press down the foot switch.
82 Press down the foot switch.                      92 With the boom fully stowed, drive the machine
                                                       onto a slope where the chassis angle is
83 With the boom fully stowed, drive the machine       greater than 3° along the X-Axis (side to side).
   onto a slope where the chassis angle is
   greater than 4.5° along the Y-Axis (front to         Result: The machine should continue to drive.
   back).                                           93 Return the machine to level ground and extend
    Result: The machine should continue to drive.      the boom approximately 91.4 cm.
84 Return the machine to level ground and extend    94 Drive the machine onto a slope where the
   the boom approximately 91.4 cm.                     chassis angle is greater than 3° along the
                                                       X-Axis (side to side).
85 Drive the machine onto a slope where the
   chassis angle is greater than 4.5° along the         Result: The machine should stop once the
   Y-Axis (front to back).                              machine reaches 3° of chassis tilt.
    Result: The machine should stop once the        95 Retract the boom to the stowed position or
    machine reaches 4.5° of chassis tilt.              drive in the opposite direction.
86 Retract the boom to the stowed position or           Result: The machine should drive.
   drive in the opposite direction.                 96 Return to level ground and raise the boom to
    Result: The machine should drive.                  approximately 15° above horizontal.
87 Return to level ground and raise the boom to     97 Drive the machine onto a slope where the
   approximately 15° above horizontal.                 chassis angle is greater than 3° along the
                                                       X-Axis (side to side).
88 Drive the machine onto a slope where the
   chassis angle is greater than 4.5° along the         Result: The machine should stop once the
   Y-Axis (front to back).                              machine reaches 3° of chassis tilt.
    Result: The machine should stop once the        98 Lower the boom to the stowed position or drive
    machine reaches 4.5° of chassis tilt.              in the opposite direction.
89 Lower the boom to the stowed position or drive       Result: The machine should drive.
   in the opposite direction.                       99 Return to level ground and stow the boom.
    Result: The machine should drive.
90 Return to level ground and stow the boom.


Part No. 1262336                           SX-150 • SX-180                                          39

--- Page 7 ---
Third Edition • Second Printing                                                           Operator's Manual


                                                                Operating Instructions
Drive Enable                                            Engine Idle Select (rpm)
Light on indicates that the boom                        Select the engine idle (rpm) by
has moved past a circle-end tire                        pressing the engine idle select
and the drive function has been                         switch. The indicator light next to
interrupted.                                            the current setting will be on.


To drive, move the drive enable switch and slowly
move the drive/steer control handle off center.            Turtle symbol: low idle
If the drive/steer control handle is not moved within      Rabbit symbol: high idle
two seconds of moving the drive enable switch, the
drive function will not operate. Release and move       Check Engine Light
the drive enable switch again.
                                                                     Light on and engine stopped: Tag the
Be aware that the machine may move in the                            machine and remove from service.
opposite direction that the drive and steer controls
are moved.                                                           Light on and engine still running:
                                                                     Contact service personnel within
Always use the color-coded direction arrows on the                   24 hours.
platform controls and the drive chassis to identify
the direction the machine will travel.
When the drive enable light is on, the axles cannot
retract.


Part No. 1262336                              SX-150 • SX-180                                             49

--- Page 8 ---
Third Edition • Second Printing                           Operator's Manual


                                  Transport and Lifting Instructions

SX-150


Part No. 1262336                    SX-150 • SX-180                     59

View the complete manual on HeyDownloads →