PDF Operation & Maintenance Manual Komatsu SK820-5 Turbo Skid Steer Loader - 7 MB

Master the operation and care of your Komatsu SK820-5 Turbo Skid Steer Loader with this essential manual.

It covers all control functions, safety protocols, and scheduled maintenance intervals.

Following the manufacturer's recommendations is vital for the longevity and reliability of your machine.

This guide provides all the necessary information to keep your skid steer in top working condition.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
WEAM005400


Operation & Maintenance
Manual


 SK820-5 turbo
  SKID-STEER LOADER
  SERIAL NUMBERS SK820-5 turbo                                              37BTF50003 and up


This material is proprietary to Komatsu America Corp. and is not to be reproduced, used, or disclosed except in
accordance with written authorization from Komatsu America Corp..

It is our policy to improve our products whenever it is possible and practical to do so. We reserve the right to make
changes or improvements at any time without incurring any obligation to install such changes on products sold
previously.

Due to this continuous program of research and development, revisions may be made to this publication. It is
recommended that customers contact their distributor for information on the latest revision.

                                                                Copyright 2003 Komatsu
                                                                Printed in U.S.A.
                                                                Komatsu America Corp.
October 2003

--- Page 3 ---
TABLE OF CONTENTS
                                                                                                                                                         Page
                                                  TABLE OF CONTENTS
1.1   FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .      1
1.2   INFORMATION ON SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                   3
1.3   INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .       5
      1.3.1 INTENDED USES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                 5
      1.3.2 IMPROPER OR UNAUTHORIZED USES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                                     5
      1.3.3 MAIN CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                        6
      1.3.4 RUNNING-IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .            6
1.4   PRODUCT IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                  7
      1.4.1 MACHINE SERIAL NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                         7
      1.4.2 MACHINE IDENTIFICATION PLATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                              7
      1.4.3 ENGINE SERIAL NUMBER AND EXHAUST GAS EMISSION PLATE . . . . . . . . . . . . . . . . .                                                           8
      1.4.4 TRAVEL REDUCTION GEAR SERIAL NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                                           8
      1.4.5 CAB SERIAL NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                     8
      1.4.6 EXCAVATOR IDENTIFICATION PLATE (if installed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                                     8
      1.4.7 SERIAL NUMBERS AND DISTRIBUTOR’S ADDRESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                                              9


SAFETY AND ACCIDENT PREVENTION
2.1   SAFETY, NOISE AND VIBRATION PLATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                             18
      2.1.1 POSITION OF THE SAFETY PLATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                              18
      2.1.2 POSITION OF THE PICTOGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                               36
      2.1.3 PICTOGRAMS AND RELEVANT MEANINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                                       40
      2.1.4 VIBRATIONS TO WHICH THE OPERATOR IS SUBJECTED . . . . . . . . . . . . . . . . . . . . . . . .                                                  43
2.2   GENERAL PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                44
      2.2.1 GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                       44
      2.2.2 SAFETY DEVICES AND GUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                              44
      2.2.3 CLOTHING AND PERSONAL PROTECTION ITEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                                             44
      2.2.4 UNAUTHORIZED MODIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                               45
      2.2.5 LEAVING THE OPERATOR’S SEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                                45
      2.2.6 GETTING ON AND OFF THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                                   46
      2.2.7 CHECKING THE REAR-VIEW MIRRORS (if installed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                                        46
      2.2.8 PREVENTING FIRES DUE TO FUEL AND OIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                                     47
      2.2.9 PREVENTING BURNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                     47
      2.2.10 PREVENTING DAMAGE DUE TO ASBESTOS POWDER . . . . . . . . . . . . . . . . . . . . . . . . . .                                                  48
      2.2.11 PREVENTING DAMAGE CAUSED BY THE WORK EQUIPMENT . . . . . . . . . . . . . . . . . . . .                                                        48
      2.2.12 FIRE EXTINGUISHERS AND FIRST AID KIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                                  49
      2.2.13 PRECAUTIONS CONCERNING THE CAB STRUCTURE . . . . . . . . . . . . . . . . . . . . . . . . . . .                                                49
      2.2.14 PRECAUTIONS CONCERNING THE EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                                            49
2.3   PRECAUTIONS TO BE TAKEN BEFORE STARTING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . .                                                   50
      2.3.1 SAFETY ON THE WORK SITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                          50
      2.3.2 FIRE PREVENTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                50
      2.3.3 PRECAUTIONS TO BE TAKEN FOR THE OPERATOR'S CAB . . . . . . . . . . . . . . . . . . . . . .                                                     50
      2.3.4 ROOM VENTILATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                   51
      2.3.5 PRECAUTIONS TO BE TAKEN FOR THE LIGHTS (if installed) . . . . . . . . . . . . . . . . . . . . . .                                              51
      2.3.6 CLEANING THE WINDOWS AND THE REAR-VIEW MIRRORS - CHECKING
            THE WINDSHIELD WIPER BLADES (if installed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .                                   51


10

--- Page 4 ---
SAFETY, NOISE AND VIBRATION PLATES


1.
• Warning Decal.
                                            WARNING

                                     Improper operation and main-
                                     tenance can cause serious
                                     injury or death.

                                     Read manual and labels be-
                                     fore operation and mainte-
                                     nance.
                                     Follow instructions and warn-
                                     ings in manual and in labels
                                     on machine.

                                     Keep manual in machine cab
                                     near operator.
                                     Contact Komatsu distributor
                                     for a replacement manual.
                                                                    RWA16810


2.
• Height Decal                                DANGER


                                     Hazardous voltage hazard.
                                     Serious injury or death can
                                     occur if machine or attach-
                                     ments are not kept safe dis-
                                     tance away from electrical
                                     lines.
                                      Line Voltage     Safe Distance
                                          6.6 kV     At least 10ft (3m)
                                         66.0 kV     At least 16ft (5m)
                                        275.0 kV     At least 33ft (10m)
                                                                    RWA16820


20

--- Page 5 ---
SAFETY, NOISE AND VIBRATION PLATES


26.
• Arm floating device control (Right control lever)


                                                      RWA32930


27.
• Speed increase control (Left control lever)


                                                      RWA34220


30

--- Page 6 ---
SAFETY, NOISE AND VIBRATION PLATES


2.1.3 PICTOGRAMS AND RELEVANT MEANINGS
The warning and danger plates applied on to the machine are accompanied or represented by pictograms.
The personnel in charge with the operation and maintenance of the machine must know the symbols contained in
the pictograms perfectly; the following description illustrates what they look like and their respective meanings.


DANGER IN THE WORK AREA
(Only for machines with excavator)
• Do not approach or stand within the equipment operating radius
  when the boom and the bucket of the excavator are raised.


                                                                                                         RWA00020


MOVING PARTS IN ENGINE COMPARTMENT
• Keep clear; moving parts hazard inside engine compartment.


                                                                                                        RWA00010


CONSULT THE MANUAL
• Carefully read the contents of the manual before using the ma-
  chine or performing maintenance operations.


                                                                                    RWA00030


40

--- Page 7 ---
PRECAUTIONS TO BE TAKEN BEFORE STARTING THE ENGINE


2.3 PRECAUTIONS TO BE TAKEN BEFORE STARTING THE ENGI-
    NE
2.3.1 SAFETY ON THE WORK SITE
• Before starting the engine, thoroughly check the area for any
  unusual condition of the ground due to which work may be dan-
  gerous.
• Check the conditions of the ground at the work site and before
  starting the engine define the work plan and the best and safest
  operating procedure.
• Make the ground surface as level as possible before carrying
  out any operation.
• In case of work on the road, protect pedestrians and cars by de-                                        RWA37100

  signating a person for work site traffic duty and install fences
  around the work site.
• If water lines, gas lines, and telephone or high-voltage electrical
  lines are located under the work site, contact the relevant utility
  company in order to find out their exact positions or to make
  them ineffective until the end of the operations. Be careful not to
  sever or damage any of these lines.
• Check the depth and flow of water before operating in water or
  on river banks.


2.3.2 FIRE PREVENTION
• Carefully remove all wood chips, rubbish, paper and other flam-
  mable materials that may have accumulated inside the engine
  compartment, since they can cause fires.
• Check the fuel and hydraulic system pipes for leaks and if ne-
  cessary repair them. Wipe up any leakage of oil, fuel or other
  flammable fluids.
• Make sure that fire extinguishers are available for use in the
  work area.
                                                                                                         RWA01040


2.3.3 PRECAUTIONS TO BE TAKEN FOR THE OPERATOR’S CAB
• Do not keep objects or tools in the operator’s cab. They may hinder the operation of the controls and cause se-
  rious accidents.
• Keep the cab floor and the controls (pedals and levers) clean, by removing any trace of oil and grease and, as
  far as the floor is concerned, remove any excess dirt (earth, stones, etc.).
• Check the safety belt and change it if it is broken or damaged.
  Replace any component only with homologated parts supplied by Komatsu or its Dsrtibutors.


50

--- Page 8 ---
BATTERY


2.6 BATTERY
2.6.1 SAFETY PRECAUTIONS FOR WORK
      ON BATTERIES
• Electrolytic batteries contain sulphuric acid which can cause
  burns. It can also corrode clothing and make holes in it. If you
  inadvertently splash battery acid on yourself or on someone el-
  se, immediately wash the affected part with plenty of water.
• Battery acid may cause blindness if it comes into contact with
  the eyes.
  If acid accidentally gets into your eyes, wash them immediately
  with plenty of water and consult a doctor right away.                         RWA01060

• If you accidentally swallow battery acid, drink a large quantity of
  water or milk, beaten egg white or vegetable oil and in any case
  antiacid substances like magnesia, bicarbonate, etc.; call a          WRONG
  doctor or a poison treatment center immediately.
• Always wear safety goggles when working on batteries.
• Batteries produce hydrogen, which is highly explosive and can
  be easily ignited with small sparks or exposed flames.
• Before working with batteries, stop the engine and remove the
  ignition key.
• Avoid short-circuiting the battery terminals through accidental
  contact with metal objects or tools or through the inversion of               RWA01080
  the terminals.
• Tighten the battery terminals securely. Loose terminals may ge-
  nerate sparks and even cause the explosion of the battery.


                                                                                RWA01180


2.6.2 STARTING WITH BOOSTER CABLES
• When starting the machine with booster cables, always wear
  safety goggles.
• When starting the engine by means of another machine, avoid
  any contact between the two machines.
• Be sure to connect the positive cable (+) first and then the ne-
  gative or ground cable (-) when connecting the booster cables.
  After the start, disconnect first the negative or ground (-) cable
  and then the positive cable (+).
• Connect the batteries in parallel: positive to positive and negati-           RWA01190

  ve to negative.
• When connecting the ground cable to the frame of the machine
  to be started, operate as far as possible from the battery. (See
  "3.15.3 IF THE BATTERY IS DEPLETED").


60

--- Page 9 ---
PRECAUTIONS TO BE TAKEN DURING MAINTENANCE


2.8.21 PRECAUTIONS TO BE TAKEN WHEN USING THE SYNTHETIC BIODE-
       GRADABLE OIL TYPE «HEES»
• It is not possible to mix the synthetic biodegradable oil type HEES with ordinary hydraulic oils, since when the
  temperature increases insoluble compounds are generated, which are deposited on the filters and clog them
  (the maximum concentration of ordinary oil cannot exceed 1% of the total quantity of oil).
• The biodegradable oil can be used only in the hydraulic system; it cannot be used for the endothermic engine,
  the transmissions, the braking system, etc.
• Before introducing the synthetic biodegradable oil in the hydraulic system, empty the system completely, discon-
  necting the cylinders and all the parts that may contain ordinary oil, and replace the drain filter with a new one.
  Start the engine and let it idle without using the work equipment , wait until the oil reaches a temperature of at le-
  ast 40ºC (104°F), then start moving the equipment, so that all the parts of the system are filled with oil. Stop the
  engine and check the oil level (see "4.7.2.e CHECKING THE HYDRAULIC SYSTEM OIL LEVEL").


70

--- Page 10 ---
GENERAL VIEWS


10 - Left console switches
11 - Right console switches


                                   10
                                        RWAA11260


                              11
                                        RWAA9720


80

--- Page 11 ---
INSTRUMENTS AND CONTROLS


3-    LEFT STABILIZER BUTTON (if installed)
This is a button with two temporary positions and the neutral posi-
tion at its centre.
Press the button forward or backward to lower or raise the stabiliz-
er.
For use, see ”3.3.5 pos. 14 LEFT STABILIZER CONTROL”


                                                                       RWA23320


4-    RIGHT STABILIZER BUTTON (if installed)
This is a button with two temporary positions and the neutral posi-
tion at its centre.
Press the button forward or backward to lower or raise the stabiliz-
er.
For use, see “3.3.5 pos. 13 RIGHT STABILIZER CONTROL”


                                                                       RWA23310


5-    WORKING LIGHT SWITCH
Enables the circuit of the working lights.


                                                                       RWA07180


6-    EMERGENCY SWITCH (HAZARD)
Operates all the direction lights at the same time and must be
used whenever the machine is temporarily parked on the road-
side or in anomalous position while traveling on roads.


                                                                       RWA20210


90

--- Page 12 ---
INSTRUMENTS AND CONTROLS


3-    ARM LIFTING CONTROL LEVER

      WARNING
• Before carrying out any maneuver with this lever, the operator must be seated in the work position with
  fastened safety belt; before any maneuver he must perform the operations described in “3.13 USING THE
  WORK EQUIPMENT”.
• When traveling on roads, always lock the equipment control (see “3.3.5 pos. 8 EQUIPMENT CONTROL
  LOCKING LEVER”).
• Before leaving the operating position, lower the equipment to the ground and lock the safety bars (verti-
  cal position), then stop the engine.
• Failure to comply with these instructions may lead to serious accidents.


      CAUTION
• The self-leveling system is operated automatically only when the arm is lifted with loaded bucket. When
  the arm is in the lowering phase the system cannot be operated.
• At the maximum height the self-leveling system keeps the bucket partially folded to prevent the material
  from falling out of the bucket itself.


The equipment control lever (3) is positioned on the operatorís
right and controls the arm lifting and lowering and the bucket
dumping and folding functions.
The following diagrams show the basic maneuvers and the possi-
ble combined maneuvers.
                                                                    3


                                                                                                      RWAA9790


BASIC MANEUVERS

N - Neutral
A - Arm lowering                                                                              A
B - Bucket dumping
                                                                                     D
C - Arm lifting                                                                           N
D - Bucket folding                                                                                B
                                                                                         C


                                                                                                      RWA22430


100

--- Page 13 ---
INSTRUMENTS AND CONTROLS


11 - FLOATING DEVICE CONTROL
     (IF INSTALLED)
The right joystick grip is provided with a switch (1) that when
pressed (WARNING LIGHT ON) (see “3.3.2 pos. 8 FLOATING                     1
DEVICE WARNING LIGHT”) frees the loader arm (floating posi-
tion), that is, allows it to automatically follow the undulations of the
ground.
Press the switch again to restore the standard operating condi-
tions (WARNING LIGHT OFF) (see “3.3.2 pos. 8 FLOATING DE-
VICE WARNING LIGHT”).
                                                                               RWAA11330


                                                                               RWA35990


12 - PATTERN SHIFTING CONTROL

       WARNING
• Before using the pattern shifting, lower the equipment to
  the ground, engage the safety devices and stop the engine.
• Failure to comply with these instructions may lead to seri-
  ous injuries or even death.

The pattern shifting control is applied to the rear wall of the cab
and can be reached after opening the engine hood (see “3.5.1                    RWA37070
ENGINE HOOD”).
The lever (1) of the pattern shifting control has two positions:
• ISO CONTROL SYSTEM
  Lever in position A
• OPTIONAL CONTROL SYSTEM
  Lever in position B


                                                                               RWAA13490


110

--- Page 15 ---
GUARDS AND DRIVER’S SEAT


3.5.3.1 RAISING THE CAB
• Stringere sempre le viti di fissaggio della cabina a coppia
        WARNING
  rispettando     i valori riportati nella sezione «4.4.2 COPPIE DI
  SERRAGGIO SPECIFICHE».
• Raise the cab only with the machine parked on a firm and
  level surface and with arm lowered to the ground complete
Per alcune operazioni di manutenzione o di servizio è richiesto il
  with bucket or any other optional equipment.
sollevamento della cabina che deve essere eseguito in due per-
  Make sure that the surface on which the machine is parked
sone e secondo la procedura.
  is not slippery.
  1 - Fermare la macchina su terreno solido ed in piano.
• Before raising the cab, make sure that the engine hood is
  2 - Posare le attrezzature a terra.
  open.
                                                                                       RWAA13300
  3 - Applicare il freno di stazionamento e bloccare i comandi sol-
• The cab must be raised or lowered by two persons, one per
      levando le barre di sicurezza.
  side, and it is important to make sure that the handles and
  4 - Arrestare
  hold points are   il motore  conwith
                        not dirty    le modalità  della sezione «3.8 AR-
                                         oil or grease.
      RESTO MOTORE».
• After raising the cab, always engage the safety split pin of
  5 - Rimuovere le viti anteriori (1) di fissaggio cabina. Usare chi-
  the cab overturning protection lock.
      ave esagonale da 19 mm.
•6Do- Concarry
      not           outdiany
             l’ausilio    unaoperation     on the machine
                               seconda persona,     sollevareiflathe safety
                                                                   parte an-
  splitteriore
         pin ofdella
                  the cabina
                        cab overturning      protection   lock   is not  en-
                               utilizzando le maniglie e ribaltarla all’in-
  gaged.
      dietro fino alla posizione di arresto.                                       1
•7
 Always  tighten
   - Applicare la the cab fastening
                   copiglia           screws
                            di sicurezza      with
                                         (2) del    the antiribalta-
                                                 fermo  torque in-
 dicated in “4.4.2 SPECIFIC DRIVING TORQUES”.

To carry out some maintenance or routine operations it is neces-                       RWAA13310
sary to raise the cab, an operation that must be carried out by two
persons according to the prescribed procedure.
  1 - Stop the machine on firm and level ground.
  2 - Lower the equipment to the ground.                                       3
  3 - Apply the parking brake and lock the controls by lifting the
      safety bars.
  4 - Stop the engine as indicated in “3.8 STOPPING THE EN-
      GINE”.
  5 - Open the engine hood (see “3.5.1 ENGINE HOOD”) and re-
      move the rear screws (1) that fasten the cab.
      Use a 19 mm hexagon spanner.                                                 2
  6 - With the help of another person, raise the rear part of the
                                                                                        RWAB0010
      cab using the appropriate handles and overturn it forwards
      until it stops.
  7 - Engage the safety split pin (2) of the cab overturning protec-
      tion lock (3).


120

--- Page 16 ---
USE OF THE MACHINE


Before moving the machine, check the instruments, warm up the engine and the hydraulic system oil, make sure
that the safety device of the controls is released (safety bars down) and the bucket is folded; the equipment control
lever must be in neutral position.
Release the parking brake.


1 - Pull the hand accelerator lever and set the engine running at
    idling speed.


                                                                                                             RWA32510


2 - Operate the lever (1), shifting it forward to make the machine
    advance or backward to make it move in reverse.

                                                                                                       1


                                                                                                             RWAA11470


                                                                                 N


                                                                                                            RWA31930


130

--- Page 17 ---
PARKING THE MACHINE


3.7.2 PARKING ON SLOPES

      WARNING
• The movement of the machine when the operator is not on
  board may cause serious accidents and even death; to pre-
  vent this, carry out the operations described below.
• Park on slopes only when it is absolutely necessary.
• Park only with the bucket directed downwards.

                                                                              RWA37390
 1 - Park the machine with the bucket directed downwards and
     resting against an obstacle.
     If this is not possible due to the absence of natural ob-
     stacles, rotate the bucket forward and thrust its teeth into the
     ground.
 2 - Lock the equipment and travel hydraulic control by shifting
     the safety bars to the lock position (see “3.3.5 pos. 1 SA-
     FETY BARS”).
 3 - Engage the retainer to lock the optional equipment control
     pedal.
 4 - Apply the parking brake.
 5 - Stop the engine following the procedure indicated in para-
                                                                            RWAA13110
     graph “3.8 STOPPING THE ENGINE”.
 6 - Remove the ignition key.
 7 - Leave the cab using the handles and the footboards.
 8 - Position safety wedges under the wheels.
 9 - Refuel, taking the necessary precautions.


                                                                            RWAA12610


                                                                        P


                                                        RWA02000            RWAA11160


140

--- Page 18 ---
USING THE WORK EQUIPMENT


3.13.3 LOADING MATERIAL FROM PILES
       AND ON LEVEL SURFACES
The efficiency of the bucket depends on how the operator begins
to load; keep to the following rules:
1 - Start moving with the arm completely lowered and direct the
    bucket toward the base of the pile.
2 - While the material on top of the pile falls into the bucket, gra-
   dually raise the arm and at the same time fold the bucket until
   reaching the end of stroke.
                                                                        RWA37480


                                                                        RWA37490


3 - Invert the machine motion and dump the bucket on to the
    truck.


☞ IMPORTANT
• Start loading the truck from the cab side and, if the material
  is sufficiently homogeneous, dump from the maximum hei-
  ght in order to increase the compactness of the material
  and its distribution on the loading surface.


                                                                        RWA37500


4 - After removing the pile completely, incline the bucket forward,
    lower the arm until raising the front wheels slightly and, proce-
    eding in reverse, level the ground distributing the material uni-
    formly.
    Repeat the operation reducing the inclination of the bucket for
    the finishing work.


                                                                        RWA37510


150

--- Page 19 ---
LONG PERIODS OF INACTIVITY


3.14 LONG PERIODS OF INACTIVITY
3.14.1 BEFORE THE PERIOD OF INACTIVITY

       WARNING
• When draining the fuel, do not smoke or bring exposed
  flames near the machine.
  Place a container under the machine to gather the fuel and
  prevent it from spreading around.
  If some fuel is spilled, clean the dirty surface immediately.


☞
                                                                                                                        RWA37070
       IMPORTANT
• To protect the cylinder rods when the machine is not used,
  position the work equipment as shown in the figure.
  (This serves to prevent the cylinder rods from rusting).


If the machine must be stored for a long period of inactivity, it is advisable to put it in a sheltered place and to take
the following precautions, in order to keep all its components sound and efficient:
 1 - Clean the machine thoroughly, repainting it where necessary in order to prevent oxidation.
 2 - Drain and change all the fluids of the hydraulic circuits and the lubricants (engine and transmission), following
     the maintenance rules.
 3 - Change all the filtering elements (air cleaner, engine oil filter, hydrulic circuit filters, diesel oil filter).
 4 - Drain the coolant and replace it with a corrosion inhibitor (permanent fluid).
 5 - Drain the normal fuel and fill the tank with at least 5 liters of special washing and protecting fuel.
 6 - Let the engine run for about 10 minutes, in such a way as to eliminate the residual normal fuel from the filters,
     the injection pump and the entire fuel supply system. This operation avoids the locking of the injection pump
     and the injectors.
     Stop the engine and refuel with normal diesel oil.
 7 - Remove the battery, check the electrolyte level and make sure that the battery charge is sufficient.
     Store the battery in a room with suitable temperature and periodically recharge it.
 8 - Grease the hydraulic cylinder rods and the equipment joints.
 9 - Seal the end of the exhaust pipe.
10 - Move the machine controls to the neutral position and engage all the safety locks.
11 - Hang a warning notice on the controls to indicate the condition of the machine.
12 - Lock the engine hood.


160

--- Page 20 ---
PAGE INTENTIONALLY LEFT BLANK


170

--- Page 21 ---
FUEL, COOLANT AND LUBRICANTS


                                           Transmission Oil                                  Anti-freeze
                        Engine Oil                                       Grease
 No.     Supplier                          GM Dexron® II C4                                   Coolant
                    API CD, CE or CF-4                                LI, EP, MoS2
                                              Allison C4                                   Permanent type

                    Premium multi grade                           Komatsu Super
                    Engine Oils PM701     Komatsu PM704           Grease NLGI 2
  1    KOMATSU                                                                                     —
                    SAE 10W/30            (1902) Dexron® III      PM706
                    SAE 15W/40                                    ASTM D 128

                    Amoco 300
  2    AMOCO                              Dexron II ATF           Molylith grease 2      Ready Antifreeze
                    SAE15W/40

                    Arcofleet S3 Plus
                    SAE 15W/40                                    Litholine HEP 2
  3    ARCO                               ATF Dexron II                                  Sincol-Blu (-40°C)
                    Hy-Vis HD extra S3                            Arco EP moly D
                    plus SAE 15W/40

                    Vanellus C3
                    SAE 15W/40
  4    BP                                 Autran MBX              Grease LTX2-M          Sigil Fluid (-40°C)
                    Vanellus C3 Extra
                    SAE 15W/40

                    RPM Delo 500
                                                                                         AF eng. coolant
  5    CALTEX       RPM Delo 600          ATF-HD                  Molytex EP2
                                                                                         CX eng. coolant
                    RPM Delo SPH

  6    CASTROL      Turbomax RX super     TQ - Dexron II          Spheerol LMM           Anti-freeze (pure)

                    Delo 400              Supreme Automatic
  7    CHEVRON                                                    Moly grease            Flurant
                    Delo 500              Transmission Fluid

  8    CITGO                   —          D-21571                          —                       —

                    Fleet motor oil       D21718
  9    CONOCO                                                              —             Fleet Heavy Duty
                    SAE 15W/40            D21570

                    Essolube TD
                                          ATF Dexron II D
       EXXON        SAE 15W/40                                    MP Grease
 10                                       D-21849 (East Canada)                          All season coolant
       (ESSO)       Heavy Truck Diesel                            Moly
                                          D-21848 (West Canada)
                    Motor Oil SAE15W/40

                    Super Duty

View the complete manual on HeyDownloads →