PDF Operation & Maintenance Manual Doosan DX225LC Excavator - 4 MB

This Operation & Maintenance Manual is the authoritative guide for the Doosan DX225LC Excavator.

It provides operators with detailed instructions on controls and safe operating techniques.

The maintenance section outlines all the necessary periodic service tasks to ensure machine reliability and longevity.

This manual is a crucial tool for both operators and service personnel to keep the excavator performing safely and efficiently.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
950106-00365ANA
                                      July 2014


EXCAVATOR

Operation &
Maintenance
Manual
DX225LC-3
Serial Number 1001 and Up
Serial Number 50001 and Up (Europe Only)

--- Page 3 ---
Component Model and Serial Numbers
There are model and serial numbers on each traceable
component of machine. For example, the engine serial number
is stamped on rear left side of the engine block, above the
starter. Additional engine information is described on a label
(Figure 3) on head cover.
Record these numbers and their locations. These will be
required whenever warranty or service work is requested.

                                                                              FG019408
                                                                   Figure 3


Safety Messages
Safety messages and safety decals included in this manual and
on the machine provide instructions how to operate, service and
maintain the machine. Safety messages and safety decals
indicate potential hazards and describe safety precautions
required to avoid hazards. Operator and maintenance personnel
should read and understand these safety messages and decals
before beginning operation or maintenance.


         SAFETY ALERT SYMBOL
Be Prepared - Get to Know All Operating and Safety
Instructions.
This is a Safety Alert Symbol. Wherever it appears in this
manual or on safety decals on the machine, you must be
alert to the potential for personal injury or accidents.
Always     observe    safety   precautions   and    follow
recommended procedures.


Signal Words
The signal words "DANGER", "WARNING", "CAUTION" are
used throughout safety messages and safety decals in this
manual or on the machine. They indicate an existence of, and
the relative seriousness of, a hazard. All three indicate that a
safety risk is involved. Observe the precautions indicated
whenever a Safety Alert Symbol is present, no matter which
signal word appears next to it.


                           DANGER
DANGER - This signal word is used on safety messages and
safety labels and indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.


DX225LC-3                                                                     Foreword
                                                                                   0-III

--- Page 4 ---
2.   Warning Tag - "Do Not Operate" (950205-03802)


                             WARNING
               AVOID DEATH OR SERIOUS INJURY
     •   Stop engine and remove key.
     •   Attach "DO NOT OPERATE" warning tag to the
         controls before servicing the machine.
     •   Do not operate when performing inspection or          EX1301177
         maintenance.


3.   Keep Bystanders Away (950205-03803)


                             WARNING
               AVOID DEATH OR SERIOUS INJURY
     •   Keep out of swing area and travel path.
     •   Always look in the travel direction.
     •   Make sure swing area is clear of bystanders and
         objects.


4.   Hot Pressurized Fluid (950205-03781)


                             WARNING
              HOT PRESSURIZED FLUID CAN CAUSE
                      SERIOUS BURNS
     •   Do not loosen or open cap when hot.
                                                               EX1301180
     •   Before opening:
         1)     Turn engine off.
         2)     Allow machine to cool.
         3)     Tip cap and open slowly to relieve pressure.


5.   Entanglement in Rotating Parts (950205-03791)


                             WARNING
          ROTATING PARTS CAN CAUSE DEATH OR
                    SERIOUS INJURY
     Keep away from belt and rotating parts. Stop engine
     before servicing.                                         EX1301181


DX225LC-3                                                         Safety
                                                                     1-7

--- Page 5 ---
Proper Work Tools and Attachments
Only use work tools and attachments that are recommended by
DOOSAN for use on DOOSAN machines. When installing and
using optional attachments, read instruction manual for
attachment, and general information related to attachments in
this manual. Because DOOSAN cannot anticipate, identify or
test all attachments that owners may want to install on their
machines, contact DOOSAN for written authorization and
approval of attachments, and their compatibility with optional
kits.
Attachments and attachment control systems that are
compatible with the machine are required for safe and reliable
machine operation. Do not exceed maximum operating weight
(machine weight plus attachment) that is listed on ROPS
certification plate.
Make sure that all guards and shields are in place on machine
and on work tool. Depending on type or combination of work
equipment, there is a potential that work equipment could
interfere with the cabin or other parts of machine. Before using
unfamiliar work equipment, check if there is any potential of
interference, and operate with caution.
While you are performing any maintenance, testing, or
adjustments to attachments, stay clear of the following areas:
cutting edges, pinch points, and crushing surfaces.
Never use attachment as a work platform or manlift.
Contact your DOOSAN distributor about auxiliary hydraulic kits
for attachments installation. If you are in doubt about
compatibility of a particular attachment with a machine, consult
your DOOSAN distributor.


Pressurized Fluids
Pressurized air or fluids can cause debris and/or fluids to be
blown out. This could result in death or serious injury.
Immediately after operations are stopped, coolant, engine oil,
and hydraulic oil are at their highest temperatures and the
radiator and hydraulic tank are still under pressure. Always wait
for temperature to cool down. Follow specified procedures when
attempting to remove caps, drain oil or coolant, or replacing
filters. Always wait for temperature to cool down, and follow
specified procedures when performing these operations. Failure                 FG018457
to do so can result in death or serious injury.                     Figure 4
When pressurized air and/or pressurized water is used for
cleaning, wear protective clothing, protective shoes, and eye
protection. Eye protection includes goggles or a protective face
shield.
Pressure can be trapped in a hydraulic system and must be
relieved before maintenance is started.


DX225LC-3                                                                        Safety
                                                                                   1-17

--- Page 6 ---
Protecting Cabin from Flying or Falling Objects (Optional)
In a work site where additional operator protection is necessary
from falling or flying objects, install adequate protective guards        1
on the cabin.
For breaker operation, install a front guard (1, Figure 20) and
apply a laminated coating sheet to front glass. Contact your
DOOSAN distributor for recommendations.
When performing demolition or cutting operation, install a front
guard and top guard.
Apply a protective laminated coating sheet to outside of front
window. This will prevent glass from being scratched by dust
when cleaning it or running wipers.


                                                                                 FG020947
                                                                     Figure 20

When working in mines, quarries or other work sites where there
is a hazard of falling rocks, install Operator Protection Guard
(OPG) (2, Figure 21) and apply a laminated coating sheet to
front glass.
When OPG is installed, and front window needs to be cleaned,
loosen bolts marked with arrows (Figure 21). Be sure to tighten
bolts when done.
Never attempt to alter or modify any protective structure             2
reinforcement system, by drilling holes, welding, remounting or
relocating fasteners. Any serious impact or damage to system
requires a complete inspection of the structure. Reinstallation,
recertification and/or replacement of system may be necessary.
Contact your DOOSAN distributor for available safety guards
and/or recommendations to protect against objects that could
strike operator's cabin. Make sure that all other work site crew
members are kept away from excavator when operating.
If any glass on machine is broken, replace it with new glass
immediately.
NOTE:      The preceding instructions assume that conditions
           are for standard operations, but it may be necessary                  FG018595
           to add additional guards depending on operating           Figure 21
           conditions or local rules or regulations for the work
           site. Always contact your DOOSAN distributor for
           advice.


DX225LC-3                                                                          Safety
                                                                                     1-27

--- Page 7 ---
•    Check mirrors and rear view camera (if equipped) on
     machine before starting operations. Clean off any dirt and
     adjust view for good visibility.
When operating or traveling during poor visibility conditions,
follow the preceding work site rules.
It may not be possible to adjust all visual aids to see all the way
around the machine. Therefore, additional precautions such as
flagman, barricades, etc., must be taken to keep other personnel
out of the work area.


Boost Starting or Charging Engine
   Batteries
Follow these instructions to prevent an explosion or fire when
connecting booster cables to batteries:
•    Turn "OFF" all electric equipment before connecting leads
     to battery. This includes electric switches on battery
     charger or battery booster equipment.
•    When boost starting from another machine or vehicle do
     not allow two machines to touch. Wear safety goggles and
                                                                                  HAOA310L
     gloves while battery connections are made.
                                                                      Figure 27
•    24 volt battery units consisting of two series connected 12
     volt batteries have a cable connecting one positive (+)
     terminal on one of the 12 volt batteries to a negative (-)
     terminal on the other battery. Booster or charger cable
     connections must be made between the non series
     connected positive (+) terminals and between the negative
     (-) terminal of the booster battery and metal frame of the
     machine being boosted or charged. The final booster cable
     connection, at metal frame of the machine being charged
     or boost started, must be as far away from the batteries as
     possible. Refer to “Starting Engine With a Booster Cable”
     on page 3-11, for proper procedure in this manual.
•    Connect positive (+) cable first when installing cables and
     disconnect negative (-) cable first when removing them.


DX225LC-3                                                                           Safety
                                                                                      1-37

--- Page 8 ---
Check After Long-term Parking
•   All oil and fluid levels.
•   Tension of all belts.
•   Air pressure.
•   Air cleaner.
•   Batteries and electrical connections.
•   Lubricate all greasing points.
•   Wipe off grease from piston rods.
•   Inspect for signs of nests (i.e. birds, rodents, etc.)


DX225LC-3                                                    Safety
                                                               1-47

--- Page 9 ---
Preparation for Electrical Welding On Body Structure
To prevent damage to ECU by electrical welding, observe the
following procedures:
1.   Turn battery disconnect switch to "OFF" position.
2.   Disconnect the connector between ECU and machine, and
     the connector between ECU and engine.
3.   Proceed with welding.                                                   ON             OFF

4.   After welding, connect the connector between ECU and
                                                                                                  FG020630
     machine, and the connector between ECU and engine.
                                                               Figure 43
5.   Clean battery compartment.
6.   Turn battery disconnect switch to "ON" position.
7.   Close battery compartment door.


                                                                    Electric Control Unit
                                                                            (ECU)                 FG020631
                                                               Figure 44


Warning for Counterweight and Front
   Attachment Removal


                          WARNING
            AVOID DEATH OR SERIOUS INJURY
Removal of the machine counterweight, front attachment or
any other part can affect the stability of the machine. This
could cause unexpected movement, and result in death or
serious injury.
Never remove counterweight or front attachment unless the
upper structure is in-line with the lower structure.                                              FG018594
Never rotate the upper structure once the counterweight or     Figure 45
front attachment has been removed.


DX225LC-3                                                                                            Safety
                                                                                                       1-57

--- Page 10 ---
Underground Operation
If excavation is in an underground location or in a building, make
sure there is adequate overhead clearance, and adequate
ventilation.
Special equipment and engines may be required in some
countries. Contact your DOOSAN distributor for more
information..
Check that there is sufficient compartment for machine and load.
Move slowly.
Make sure that authorities or companies responsible for
underground cables, utilities, and electrical lines have been
contacted and that their instructions are followed. Also check
which rules apply to ground personnel regarding exposing
cables, utilities and electrical lines.                                              FG018419

Consider all electrical cables as live.                              Figure 55


Working in Water

                     IMPORTANT
Do not exceed maximum permissible water depth. The
water level must not reach higher than centerline of upper
track roller(s) (1, Figure 56).

After working in water, lubricate all lubrication points on                      1   FG018427
undercarriage, which have been underwater so water is
                                                                     Figure 56
removed. Check that no water has entered travel gearboxes and
undercarriage components.


Working in Contaminated Environment
When working within area which is contaminated or where there
is a health risk, check local regulations and contact your
DOOSAN distributor for assistance with identifying what
additional safety precautions need to be taken.


DX225LC-3                                                                              Safety
                                                                                         1-67

--- Page 11 ---
2Operating Controls
The "Operating Controls" section consists of the following
groups:
1.    “Component Locations” on page 2-2
2.    “Operator's Area” on page 2-4
3.    “Operational Controls and Panels” on page 2-6
4.    “Display Monitor” on page 2-24
5.    “User Menu” on page 2-43
6.    “Heater and Air Conditioner Control Panel” on page 2-74
7.    “Stereo” on page 2-80
8.    “Miscellaneous Electrical Devices” on page 2-81
9.    “Seat Adjustment” on page 2-83
10.   “Ceiling Cover” on page 2-87
11.   “Front Windows” on page 2-88
12.   “Door Side Latch” on page 2-90
13.   “Cabin Storage Compartments” on page 2-91
14.   “Sunglass Case” on page 2-91
15.   “Sun Visor” on page 2-92
16.   “Hanger” on page 2-93
17.   “Cup Holder” on page 2-93
18.   “Emergency Exit Glass Breaking Tool” on page 2-93
19.   “Miscellaneous Access Covers and Doors” on page 2-94
20.   “Air Gun and Compressor (Optional)” on page 2-95


Each group is explained with a point location drawing or photo
and a brief description of each control, switch, gauge or valve.
Indicator symbols work besides the gauges on the display
monitor. The operator should monitor machine pressure on the
display monitor with indicator symbols. These symbols will only
show there is a problem.


                    IMPORTANT
When any one or more of the warning symbols on the
control console comes "ON", immediately stop operation.
Investigate and correct the problem before proceeding with
operation.


DX225LC-3                                                          Operating Controls
                                                                                  2-1

--- Page 12 ---
9. Intelligent Floating Boom Switch
   (Optional)                                                                      I
                                                                              O
    This switch is used to control the Intelligent Floating Boom        II
    function.
    O.    In this position, "NORMAL MODE" is selected.
    I.    In this position, "INTELLIGENT FLOATING BOOM
          MODE" is selected. The boom can move freely "UP"
          and "DOWN".
    II.   In this position, "BREAKER MODE" is selected.                                                FG018272
                                                                       Figure 12
    NOTE:      See “Intelligent Floating Boom Control
               (Optional)” on page 3-38 for further information.


10. Cabin Work Light Switch (Optional)
    This switch is used to control the cabin work lights, if unit is
                                                                                  O
    equipped with them.
                                                                              I
                                                                         II
    O.    In this position, all cabin work lights are turned "OFF".
    I.    In this position, the front cabin work lights on the front
          top of cabin will turn "ON".
    II.   In this position, the front cabin work lights on the front
          top of cabin and rear cabin work lights on rear top of
          cabin will turn "ON".                                                                        FG016019
                                                                       Figure 13


11. Audio Control Panel
    The audio system can be remotely controlled using this
    panel.                                                                             SCAN


                                                                                       PWR


                                                                                                       FG000018
                                                                       Figure 14


DX225LC-3                                                                                     Operating Controls
                                                                                                            2-11

--- Page 13 ---
32. Intelligent Floating Boom Temporary
    Reset Button
    After selecting Intelligent Floating Boom function, while the
    boom operating joystick is being held in boom lowering
    direction, pressing the Intelligent Floating Boom temporary
    reset button (on the right-hand joystick) will temporarily
    reset the Intelligent Floating Boom function back to normal
    operation.

                                                                                                     FG027214
                                                                    Figure 42


33. Jog Switch Control Panel                                                    2       4           3

         Reference
                                      Description
          Number
             1                       Jog Switch
             2                Power Mode Selector Button
             3                Work Mode Selector Button             5                                         6
                                  Auto Idle Selector/
             4
                                  Buzzer Stop Button
                                Camera Mode Selector/                               1                   FG018102
             5
                                 Escape (ESC) Button                Figure 43
             6                    Multimedia Button

    1.   Jog Switch
         Press or turn the switch to select the menu or to
         change figures.
         Engine speed can be changed according to the
         setting on the display monitor.
         When a pop-up occurs, press the jog switch to
         remove it.
         If this switch is pressed while on the camera screen,
         the screen will be divided into the windows according                                          FG018103
         to the number of cameras. (Optional)                       Figure 44

    2.   Power Mode Selector Button
         Used for selecting the power plus mode, power
         mode, standard mode, or the economy mode.
         Pressing the power mode selector button will display
         the available modes on the main window.
         Place the selection bar by turning the jog switch and
         select the mode by pressing the jog switch.


                                                                                                     FG018104
                                                                    Figure 45


DX225LC-3                                                                                   Operating Controls
                                                                                                          2-21

--- Page 14 ---
4.   Preheating Indicator Symbol
         In cold weather this symbol indicates that engine
         preheat function is operating.
         When this indicator symbol turns "OFF", it means that
         engine preheat cycle has been completed.


                                                                                         HAAE2000
                                                                 Figure 68

    5.   Engine Check Warning Symbol
         This symbol indicates when the engine needs to be
         check.
         NOTE:      If this symbol turns "ON" stop the machine
                    and repair the cause of the fault.
                                                                             CHECK

                                                                                           FG000045
                                                                 Figure 69

    6.   Hydraulic Oil Overheat Warning Symbol
         If the hydraulic oil temperature is too high, this
         symbol appears on the screen.


                                                                                         FG000056
                                                                 Figure 70

    7.   Pilot Filter Clogged Warning Symbol
         This symbol indicates when the pilot filter clogged.
         If this symbol is displayed, immediately stop
         operation and replace the pilot filter.
         After the pilot filter has been serviced, restart
         machine operation to remove warning symbol.


                                                                                         FG000055
                                                                 Figure 71


DX225LC-3                                                                       Operating Controls
                                                                                              2-31

--- Page 15 ---
2.   Enter Checking Mode
                                                                                                                             PM
     Enter individual symbol checking mode by pressing the jog
     switch.                                                                            H                           H


                                                                                            E                   F
                                                                                                         rpm

                                                                                    C                                   C
                                                                      Speed
                                                                  0                         40 (km/h)         Min                 Max


                                                                  s           DIG                       ISO                       USB


                                                                                                                            FG018715
                                                                 Figure 92

3.   Read Warning Message
                                                                                                                             PM
     Select the warning symbol by rotating the jog switch and
     press the jog switch to read the warning message.                                  H Warning              H
                                                                                                          000-0000-0000

                                                                                              Low E/G Oil
                                                                                            EPressure           F
                                                                                    Check E/G Oil Pressure.
                                                                                                         rpm

                                                                                    C                                   C
                                                                      Speed
                                                                  0                         40 (km/h)         Min                 Max


                                                                  s           DIG                       ISO                       USB


                                                                                                                            FG018519
                                                                 Figure 93

4.   Delete Warning Pop-up
                                                                                                                             PM
     Press escape or jog switch to delete the warning pop-up
     window.                                                                            H                           H


                                                                                            E                   F
                                                                                                         rpm

                                                                                    C                                   C
                                                                      Speed
                                                                  0                         40 (km/h)         Min                 Max


                                                                  s           DIG                       ISO                       USB


                                                                                                                            FG018714
                                                                 Figure 94


DX225LC-3                                                                                                Operating Controls
                                                                                                                       2-41

--- Page 16 ---
Max Flow (ATT)/Min Flow (ATT)
         The max flow (ATT) /min flow (ATT) can be set up as
         the max/min flow rate value of the attachment by the
         user according to the attachment's specifications.
         For instance, if the relevant attachment's use
         capacity is 90 - 120 lpm (23.8 - 31.7 gpm), the user
         can set up 120 lpm (31.7 gpm) for the max. flow rate,
         and 90 lpm (23.8 gpm) for the min. flow rate.
         The setup method is the same as the above max.
         engine limit setup method. The change value by
         stage in the jog switch operation is 10 lpm (2.6 gpm).
         User Setting Max Flow
                                                                                    Breaker 1 Setting
         The user setting max flow is designed to set up the
                                                                       Attachment Use               Button Type
         flow rate segment of the attachment to be used by             Max E/G Limit                Max E/G Limit
         the user.                                                     Max Flow(Pump)               Max Flow(Pump)
                                                                                  You can set 2value
                                                                       2 Pump Option                  in
                                                                                                Pump Option
         Within the above setup max. flow rate (pump), max.                             limit range!
         flow rate (ATT), and min. flow rate (ATT) scope, the            User Setting Max Flow
         user can set up the max. flow rate value of the
         attachment to be used.
         The setup method is the same as the above max.
         engine limit setup method. The change value by                                                              FG018498
         stage in the jog switch operation is 10 lpm (2.6 gpm).   Figure 120
         When setting up all above items, the setup limits are
         outlined as follows. If these limits are exceeded, a
         pop-up window is displayed for 3 seconds, saying
         "You can set value in limit range!".

                                                Max. Limit                                    Min. Limit
               Max E/G Limit                     1,500 rpm                                    1,000 rpm
             Max Flow (Pump)         Conforms to the max. engine limit       Conforms to the max. engine limit
                                                                                Min. flow rate (ATT) + 10 lpm
              Max Flow (ATT)              1,000 lpm (264.2 gpm)
                                                                                          (2.6 gpm)
                                                                          Of the max. flow rate (pump/ATT), the
              Min Flow (ATT)                 40 lpm (10.6 gpm)
                                                                             smaller value - 10 lpm (2.6 gpm)


    C.   Camera Setting
         The camera setting screen is designed to set up                          Vehicle Configuration
         various cameras "ON/OFF" and normal/mirror.
                                                                             Attachment Select
         From the vehicle configuration, select camera setting
                                                                             Attachment Setting
         to access the camera setting list screen.
                                                                             Camera Setting

                                                                             Jog Shuttle for Dial


                                                                   s      DIG                        ISO                  USB


                                                                                                                     FG018499
                                                                  Figure 121


DX225LC-3                                                                                             Operating Controls
                                                                                                                    2-51

--- Page 17 ---
Fast Winding/Rewinding
                                                                                 Singer - Title
        Locate the cursor at the video progress bar and click
        on the jog switch to convert into the fast winding/
        rewinding mode.                                                          Title
        On the fast winding/rewinding mode, operate the jog
        switch clockwise/counterclockwise to conduct fast
        winding/rewinding.                                                                           Next

        Fast winding/rewinding can be conducted at an
        interval of 30 seconds per click during which the jog
        switch is turned.                                                                              FG020127
                                                                Figure 155
        On the fast winding/rewinding mode, press the ESC
        button to disable the fast winding/rewinding mode.
        Replay the Next File
                                                                                 Singer - Title
        Locate the cursor at the replay the previous file
        symbol and click on the jog switch to replay the next
        file.                                                                    Title


                                                                                                     Next


                                                                                                       FG020128
                                                                Figure 156

        MP3 Files List
                                                                                 Singer - Title
        Locate the cursor at the MP3 files list symbol and
        click on the jog to move to the file list screen.
                                                                                 Title


                                                                                                     Next


                                                                                                       FG020129
                                                                Figure 157

        Select a file and replay the MP3.

View the complete manual on HeyDownloads →