PDF Operating Manual Ammann ARS 110 Single Drum Roller - 2 MB
This operating manual provides essential guidance for the safe and efficient use of the Ammann ARS 110 Single Drum Roller.
It covers all controls, safety features, and pre-operation checks in detail.
The manual also outlines the recommended maintenance schedule to ensure the machine's reliability and longevity.
Every operator should be thoroughly familiar with this document before using the roller to guarantee performance and safety on the job site.
PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
PDF viewer loading area
Text Preview from This Manual
The text below was extracted from the visible preview pages to help you confirm the manual contents before download.
--- Page 1 ---
ARS 110
SINGLE DRUM ROLLER
DEUTZ TCD3.6 L4
EU Stage V / U.S. EPA Tier 4f
OPERATING MANUAL
EDITION 10/2021 EN
Product Identification Number 3017996 -
--- Page 3 ---
OPERATING MANUAL
Every 250 hours of operation.............................................................................................................166
3.6.14 Checking the sensor of the air filter............................................................................................................................................................. 166
3.6.15 Machine lubrication.......................................................................................................................................................................................... 168
3.6.16 Checking the oil in the vibrator.................................................................................................................................................................... 171
3.6.17 Checking the oil in travel gearboxes........................................................................................................................................................... 172
3.6.18 Checking the pad-foot segments................................................................................................................................................................. 173
3.6.19 Seat switch check............................................................................................................................................................................................... 173
Every 500 hours of operation, but at least once a year....................................................................174
3.6.20 Engine oil change............................................................................................................................................................................................... 174
3.6.21 Fuel filter replacement..................................................................................................................................................................................... 177
3.6.22 Air filter cartridges replacement................................................................................................................................................................... 179
3.6.23 DEF (AdBlue) filter replacement.................................................................................................................................................................... 181
3.6.24 Engine coolant check........................................................................................................................................................................................ 184
3.6.25 Replacement of the cab ventilation filter and of the heating filter.................................................................................................. 185
3.6.26 Electrical installation check............................................................................................................................................................................ 186
3.6.27 Replacement of the air filter elements of the air conditioning unit................................................................................................ 186
3.6.28 Checking the wheel screws for tightening............................................................................................................................................... 186
Every 1,000 hours of operation..........................................................................................................187
3.6.29 Checking the engine belt................................................................................................................................................................................ 187
3.6.30 Oil change in travel gearboxes...................................................................................................................................................................... 188
3.6.31 Checking the intake pipe of the engine..................................................................................................................................................... 189
3.6.32 Checking the batteries..................................................................................................................................................................................... 190
3.6.33 Checking the engine......................................................................................................................................................................................... 191
3.6.34 Damping system check.................................................................................................................................................................................... 191
3.6.35 Checking the air-conditioning compressor for mounting.................................................................................................................. 193
3.6.36 Engine and machine diagnostics................................................................................................................................................................. 193
Every 2,000 hours of operation..........................................................................................................194
3.6.37 Oil change in the vibrator............................................................................................................................................................................... 194
3.6.38 Cleaning and checking the air-conditioning system............................................................................................................................ 195
3.6.39 Hydraulic oil and filter replacement............................................................................................................................................................ 196
3.6.40 Cleaning of the suction filter of the cab lifting and lowering unit................................................................................................... 202
3.6.41 Vent plug replacement..................................................................................................................................................................................... 203
Every 6,000 hours of operation..........................................................................................................204
3.6.42 Coolant change................................................................................................................................................................................................... 204
Maintenance as required....................................................................................................................206
3.6.43 Fuel system venting........................................................................................................................................................................................... 206
3.6.44 Regeneration of clogged SCR (Selective Catalytic Reduction) catalyst.......................................................................................... 207
3.6.45 DPF regeneration (Diesel Particulate Filter).............................................................................................................................................. 209
3.6.46 Cooler cleaning................................................................................................................................................................................................... 210
3.6.47 Machine cleaning............................................................................................................................................................................................... 211
3.6.48 Scraper adjustment........................................................................................................................................................................................... 212
3.6.49 Drum coolant....................................................................................................................................................................................................... 212
3.6.50 Charging of the battery.................................................................................................................................................................................... 213
3.6.51 Checking the screw connections for tightening..................................................................................................................................... 214
ARS 110 7
--- Page 4 ---
1.4 Optional equipment SPECIFICATION MANUAL
Air-conditioning (see Chap. 1.4.1)
Preparation for antenna radio and loudspeakers
Radio
Reverse alarm
Warning beacon (see Chap. 1.4.2)
Licence plate holder
Road traffic lighting (including direction lights)
Night operation lighting
ATC inter-axle lock
Additional padfoot segments (recommended with ATC and tractor tyres) (see Chap. 1.4.3)
Blade (see Chap. 1.4.4)
Tyre ballasting with liquid up to -25 Β°C
Air pre-filter
Padlock latch over the fuel tank
ACEecon
ACE Force (see Chap. 1.4.5)
Telematic preparation
Telematic (see Chap. 1.4.6)
Tachograph preparation
Tachograph (see Chap. 1.4.8)
Tractor tyres
Triangle for slow-moving vehicles
Fire extinguisher (see Chap. 1.4.7)
Set of filters, 500 h
Set of filters, 2000 h
Biodegradable hydraulic oil
Amman tool kit
Special colour design
Certificate of Origin
Additional documentation set
Topcon
ARS 110 17
--- Page 5 ---
OPERATING MANUAL
β’ After finishing the work with the machine, all of the defects,
damages to the machine and any repairs made must be
recorded in operation book. When drivers take turns, the
driver is obliged to report any identified facts to the follow-
ing driver.
β’ The driver must use personal protective equipment (PPE) β
work clothing, safety shoes, The clothing must not be too
loose, impaired, hair must be protected with a suitable cap.
During maintenance (lubrication, refilling and replacement
of working media) the hands must be protected with suit-
able gloves.
β’ The driver must use suitable ear protection when using the
machine without cab or with open windows.
β’ He must keep accessories of the machine as prescribed.
β’ He must keep the driverβs stand, foot rests and walkway sur-
faces clean.
β’ Before lifting off the cab and the bonnet, check that there
is a sufficient space needed for lifting and that there are no
electrical circuits there. Before lowering the cab and the
bonnet, he must check that nobody is endangered by this
activity.
β’ If the machine could come into contact with high voltage,
the following principles must be observed:
- try to leave the hazardous zone with the machine;
- do not leave the driverβs stand;
- warn the others to keep off and not touch the machine.
β’ He must keep the machine free of oil contaminants and in-
flammable materials.
ARS 110 27
--- Page 6 ---
OPERATING MANUAL
Slow backward drive β away from me
Sig. 6
Drive to the right
Sig. 7
Drive to the left
Sig. 8
Short distance travel
Sig. 9
ARS 110 37
--- Page 7 ---
OPERATING MANUAL
Steering wheel (1)
Lever A β Column tilting forward/backward Vibration button (6)
2612
Press the button to turn on/off the function.
Display (2) The function is displayed on the display (2).
Multifunction instrument to display parameters of the engine You cannot start the vibration while driving at the transport
and machine functions. speed (4th speed gear β HX, 5th speed gear β D).
P When it is vibrated on the spot, the vibration will be
switched off after 30 seconds automatically. For restar-
ting the vibration, it is necessary to drive the machine by
Travel control (3) 8 metres.
4036
4036bz
The travel control is used for braking the machine and setting
the direction and speed of travel. Speed gear increase button (7)
Travel control positions: AMN467
P Parking brake β parking brake of the machine enabled. Press the button to engage the upper speed gear.
N neutral β the machine is not braked, the function avoiding
the downhill driving is enabled, the engine idle speed is set.
0 zero position β the machine is not braked, the function Speed gear decrease button (8)
avoiding the downhill driving is disabled, the engine work-
ing speed is set. AMN468
F Forward travel Press the button to engage the lower speed gear.
R Reverse travel
The machine braking is indicated by lighting up the brake indi-
cator lamp on the display (2).
The travel speed corresponds to the combination of the speed Do not exceed the 30-minute time limit while driving at
gear selected by the buttons (7) and (8) and moving the travel
the transport speed (speed gear 5). Risk of overheating
control (3) from the zero position.
of machine parts!
The speed gear 0 is adjusted as starting after 15 minutes
after the switch box is turned off.
Blade button β down (4)
AMN402
Use the button to adjust the blade to the working position.
Blade button β up (5)
AMN403
Use the button to adjust the blade to the transport position.
Blade floating position button (4, 5)
AMN404
Press the buttons (4) and (5) at the same time to enable the
floating position of the blade.
ARS 110 47
--- Page 8 ---
OPERATING MANUAL
A/C Air-conditioning switch (24)
AMN452
It is used for turning on/off the air-conditioning system.
Air-conditioning fan speed switch (optional
equipment) (25)
2441
Air flow control.
0 β OFF
1 β minimum
2 β medium
3 β maximum
Heating temperature control (26)
It is used for adjusting the air temperature.
Heater fan speed switch (27)
AMN469
Air flow control.
0 β OFF
1 β minimum
2 β medium
3 β maximum
Air-conditioning outlets (28)
The adjustment and angle of the flaps allows you to change the
quantity and direction of the air flow.
Cab lighting (29)
592305
ARS 110 57
--- Page 9 ---
OPERATING MANUAL
Loading mode (speed gear 0)
The differential lock and the working (vibration) functions of the
machine are locked in the speed gear 0.
The loading mode icon will appear in the middle of the display.
Machine without ATC
When loading the machine, the drum slip control function is au-
tomatically active in the loading mode.
Machine with ATC
When loading the machine, the differential ATC lock is automati-
cally active in the loading mode.
256117
Differential lock button
AMN45
It is used for turning on the differential lock.
The differential lock prevents the drum from slipping when
crossing a difficult terrain.
Speed gear 0
The differential lock button is enabled automatically in the
speed gear 0.
Speed gear 1β3
The differential lock can be enabled manually only in the speed
gear 1β3.
Speed gear 4 and 5
The differential lock button cannot be enabled in the speed
gear 4 and 5.
Turn the differential lock off after the difficult ground
has been overcome!
ARS 110 67
--- Page 10 ---
OPERATING MANUAL
Coolant temperature indicator Screen switching
AMN76 AMN66
Press the button to view the following screen for 15 seconds.
To set the following screen as the home screen, hold the button
Hydraulic oil temperature indicator for 5 seconds.
2635
It shows the current hydraulic oil temperature.
Display backlight
AMN105
The display backlight intensity can be adjusted using the but-
tons.
Stop the machine and check the oil level, or look for
a defect!
ASH Ash clogging indicator
AMN406
It shows the ash clogging level.
Engine lubrication pressure
AMN113
It shows the engine lubrication pressure in kPa. SOOT Sooting indicator
AMN407
It shows the sooting level.
Current battery voltage indicator
2777
Current fuel consumption indicator
595425
Motor speed indicator
AMN77
Engine load indicator
AMN75
It shows the current engine load in %.
Counter of worked engine hours
AMN73
ARS 110 77
--- Page 11 ---
OPERATING MANUAL
Start-up procedure using leads from an external power supply:
The starting supply voltage from the external power supply must be 24 V.
Always follow the undermentioned operation sequence.
1. Connect one end of the (+) pole of the cable to the (+) pole of the discharged battery.
2. Connect the second end of the (+) pole of the cable to the (+) pole.
3. Connect one end of the (β) pole of the cable to the (β) pole of the external battery.
4. Connect the second end of the (β) pole of the cable to the part that is attached to the engine (or to the engine block).
When the engine has been started, disconnect cables in reverse order.
If two batteries are used in the machine, connect the cable pole to the (+) pole of the discharged battery that is not con-
nected to the (β) pole of the second battery.
Do not connect the (β) pole of the cable to the (β) pole of the discharged battery of the machine being started! During
the starting, heavy sparking may occur and gases of the charged battery may explode.
Uninsulated parts of clamps of the jump leads must not touch each other!
The jump lead connected to the (+) pole of the batteries must not come into contact with electrically conductive parts
of the machine β danger of a short circuit!
Do not lean over the batteries β possibility of electrolyte burns!
Avoid the presence of ignition sources β open flame, cigarettes, etc.
Do not check the presence of voltage in the wire by sparking against the machine frame.
ARS 110 87
--- Page 12 ---
OPERATING MANUAL
2.7.5 Panic response
β’ The immediate stop of the machine using the travel control (3) applies to all of the travel modes of the machine. When the travel
control (3) is changed to the opposite position through (0) within 1 second, the machine will stop β the parking brake will be ena-
bled, the engine will keep running, i.e. panic response. The machine can start moving again after the travel control (3) is changed
to the brake position (P) and the travel direction (F/R) is selected.
β’ When the machine vibration is on, the vibration will stop also when the manual vibration mode is selected.
The manufacturer does not recommend that the panic response is used to stop the machine normally. Enable the panic
response only in emergency when the machine must be stopped immediately.
2.7.6 Machine parking
β’ Park the machine on a flat and solid surface where there is no potential natural hazard (landslides, flooding, etc.).
β’ Change the travel control (3) to the brake position (P).
β’ After stopping the engine, turn off the battery disconnector before leaving the machine.
β’ Clean the machine (scrapers and drums).
β’ Check the whole machine and repair defects that occurred during operation.
β’ Lock the covers and cab of the machine.
Do not stop the hot engine instantly but let it idle for 3 minutes. The engine and the turbocharger will cool down slowly
and evenly!
ARS 110 97
--- Page 13 ---
OPERATING MANUAL
2.7.7.9 Recognition of compaction value
achievement and the status against
the target
Methods of the recognition of an increase in compaction and
the achievement of the maximum degree of compaction:
- Evaluation of compaction by means of absolute Kb va-
lue (MN/m)
- Evaluation of compaction by means of a drum jump
2.7.7.10 Evaluation of compaction by means of
Kb value
1
2
3
ACE
The value kB defines the instantaneous stiffness of the material
under the compacting element, i.e. a drum. 000 000
V 0,0 km/h
KB
This parameter is measured continuously by means of assessing 0 MN/m 0
the compaction energy transferred into the material. 000 000 000
0,0 mm
0 Hz
256A011
If the value of the Kb value does not increase in three consequ-
ent travels in the same compacted track, the material is com-
pacted to the maximum level of compaction with the given
machine.
Note:
If the achieved degree of compaction is not sufficient (as com-
pared to laboratory tests), in order to achieve a higher degree of
compaction, it is necessary to use a machine of a higher weight
category or to check the compactibility of a higher compaction
output.
ARS 110 107
--- Page 14 ---
OPERATING MANUAL
2.7.11 Scraper adjustment
Scrapers for smooth drum
β’ Loosen the nuts (1) and move the scraper (2) to the drum
at the distance of 20 mm (0.78 in) between the scraper and 1
the drum.
2
238151
Scrapers for pad-foot drum
β’ Loosen the screws (1) and move the individual scrapers (2)
to the drum at the distance of 35 mm (1.37 in).
1
1
If a small gap is adjusted between the scraper and the
drum, the scraper can get in contact with the drum when
the machine turns.
2
238183
Contact scrapers
β’ Loosen the screws (1) and move the scraper (2) to the drum.
1
2
238184
ARS 110 117
--- Page 16 ---
OPERATING MANUAL
Short-circuiting the travel pump:
β’ Disconnect the battery using the disconnector.
238182
β’ Short-circuit the hydraulic circuit of the travel by releasing
the multiple function valves of the travel pump by 3 revolu-
tions counter-clockwise.
238173
Release of the brakes:
238172
Before releasing the brake, secure the machine with
wooden scotch blocks against movement!
β’ Place a pan under the machine to catch leaking fluids.
Stop the oil soaking into the ground.
280156
ARS 110 127
--- Page 17 ---
3.1 Safety and other measures during maintenance of the machine
3.1.1 Safety during machine maintenance 3.1.2 Fire protection when operating fluids
are changed
Carry out lubrication, maintenance and adjustment as
follows: β’ Considering the fire danger, the flammable liquids used on
β’ By professionally trained personnel; the machine are divided into the following hazard classes:
β’ According to safety instructions given in the operating man- II hazard class β diesel fuel
ual; IV. hazard class β mineral oils, lubricating greases
β’ In intervals given in the lubrication chart after hours worked; β’ The oil change point must be where it cannot interfere in
β’ On the machine standing on a flat and solid surface and se- explosion or fire hazard areas.
cured against movement (with scotch blocks), always with β’ It must be identified by βNo smokingβ and βNo open fireβ
the engine off, the key removed from the ignition box and plates and signs.
the wiring disconnected;
β’ The handling area must be dimensioned so that it can catch
β’ When the tag Machine repair is attached on the steering a volume of the flammable liquid equal to the capacity of
wheel (the tag is delivered with the machine accessories); the biggest vessel, transport container.
β’ At cold machine parts; β’ It must be equipped with portable fire extinguishers.
β’ After the machine, lubrication points and maintenance plac- β’ For handling oils and diesel fuel, use vessels such as metal
es have been cleaned; barrels, jerrycans and sheet-metal cans.
β’ Using suitable, undamaged tools; β’ The transport containers must be properly closed during
β’ By replacing parts with new original parts according to the storage.
spare parts catalogue; β’ The containers must be provided with one hole, always
β’ By providing sufficient lighting of the entire machine during stored with the hole up and secured so that their content
poor visibility and at night; cannot flow out and drip off.
β’ By reinstalling all removed covers and safety elements after β’ Vessels must be marked with non-removable writings show-
the work is completed; ing the contents and flammability classes.
β’ By retightening screw connections to the specified tighten-
ing torque and checking the connections for leakage;
β’ After the operating fluids are heated β beware of burns β use
only recommended media.
After the adjustment or maintenance is completed,
check all safety devices for proper operation!
ARS 110 137
--- Page 18 ---
MAINTENANCE MANUAL
Maintenance as required
3.6.43 Fuel system venting
3.6.44 SCR catalyst regeneration (Selective Catalytic Reduction)
3.6.45 DPF regeneration (Diesel Particulate Filter)
3.6.46 Cooler cleaning
3.6.47 Machine cleaning
3.6.48 Scraper adjustment
3.6.49 Drum coolant
3.6.50 Charging of the battery
3.6.51 Checking the screw connections for tightening
* First after 100 hours
** First after 500 hours
ARS 110 147
--- Page 19 ---
MAINTENANCE MANUAL
3.6.6 Checking the fan for condition
β’ Check the fan visually. Replace the fan if damaged (e.g. miss-
ing parts of materials, cracks, shape changes, etc.).
238049
3.6.7 Checking the dust valve of the air filter
β’ Clean the exit slit and squeeze to remove any dust trapped.
Note
Any dust trapped in the dust valve is automatically emptied dur-
ing operation of the machine.
Do not work with the machine if the dust valve is dam- 238050
aged.
If the dust valve of the air filter is damaged, replace it
with a new valve of the same type!
Dust valve
Order number: 1-952454
β’ Check and clean the pre-filter bowl.
Note:
The pre-filter is mounted on special order.
238051
ARS 110 157
--- Page 20 ---
MAINTENANCE MANUAL
β’ If the indicator lamp does not light up, check the vacuum
switch, contacts and supply cables.
Sensor
Order number: 4-5358520063
238057
ARS 110 167
--- Page 21 ---
MAINTENANCE MANUAL
3.6.21 Fuel filter replacement
Fuel filter
β’ Clean the fuel filter head.
β’ Remove the filter.
238077
β’ Lubricate the seal ring of the new filter with oil.
Fuel filter
Order number: 1238008
396247
β’ Retighten the filter by 3/4 revolution after the filter is in posi-
tion.
β’ Tightening torque 10β12 Nm (7.4β8.9 lb ft).
396250A
Fuel pre-filter
β’ Disconnect the connector of the water separator sensor.
238078
ARS 110 177
--- Page 22 ---
MAINTENANCE MANUAL
Every 1,000 hours of operation
3.6.29 Checking the engine belt
Checking the engine belt for wear:
β’ Visually inspect the belt.
238086
β’ Cracks perpendicular to the belt width are not considered
to be a fault. If longitudinal cracks appear on the belt, or the
belt edges are ragged, or some material parts are pulled off,
then the belt must be replaced.
282N116T
Replacing the air-conditioning belt:
β’ Loosen the screws and move the compressor.