PDF Mechanical Maintenance Manual Cat Bucyrus 45R Electric Blast Hole Drill - 1 MB

The Cat Bucyrus 45R is a powerful electric blast hole drill, and proper maintenance is crucial for its performance.

This mechanical maintenance manual provides detailed instructions for servicing and repairing the mechanical systems of your drill.

Following the procedures in this guide will help prevent costly breakdowns and extend the life of your valuable asset.

It's a must-have for any technician working on this equipment.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
BI115923
© Bucyrus
All Rights Reserved


       BUCYRUS                      R


                      Technical Manual

--- Page 3 ---
BI115923


                                                  CHAPTERl
(
                                      SECTION 2 - LOWER WORKS

                    eRAWLER BELTS
        The crawler belts should be inspected frequently
        to prevent an unexpected breakdown (figure 1).

        Check the links for cracks, worn lugs, elongated
        link pin bores and other damage. Minor cracks in
        the link do not constitute a major problem. How-
        ever, cracked links should be repaired by welding
        or replaced at a convenient time. Links with
        broken or worn drive lugs should be replaced at the
                                                                                               FIGURE 2
        earliest convenient time as they can cause the belt
        to ride off the rollers or take-up tumblers. Links
        with elongated pin bores should be checked care-
        fully for cracks at the pin lugs and replaced if
                                                                     To Adjust Belt Tension:
        badly worn or cracked. Bent, broken, or badly                    1.   Take weight of machine off crawlers using
        worn link pins should be replaced.                                    leveling jacks. Block machine in raised posi-
                                                                              tion.
        ADJUSTMENT
        The crawler belts should be so adjusted that the               2.     Remove the tumbler shim guards from the
                                                                              inside and outside of the crawler frame.
(       sag in the belts should be approximately 3"-6"
        inches at the center points between the upper                    3.   Loosen the jam nuts and full nuts securing
        rollers (figure 2).                                                   the bearing blocks to the crawler frame on
        Adjustment of the crawler belts is accomplished at                    both sides. Loosen the nuts only enough to
        the take-up tumbler end of the belts. The take-up                     allow the bearing block to slide on the craw ler
        tumblers are mounted on shafts which are clamped                      frame.
        in bearing blocks. The bearing blocks are bolted to              4.   Position suitable hydraulic jacks behind each
        the crawler frames. Shims placed ahead or behind                      of the bearing blocks.
        the bearing blocks position the bearing block and
        tumbler to provide the desired belt tension (figure              6.   Remove several shims from in front of the
        3).                                                                   bearing blocks.


    (                                                  LOWER WORKS
                                                              FIGURE 1


                                                     ., BUCYRUS-ERIE COMPANY, 1983                                          5

--- Page 4 ---
BI115923


         7.   Install the inner sleeve bearing on the hoist            18. Repack the shaft and auxiliary reel bearings
              shaft.                                                       and lubricate the jaw clutch.
(        8.   Slide the hoist shaft into the gear sleeve. The          19. Replace the shaft assembly in the gearcase.
              shaft should be installed from the right side
              of the sleeve. Install the inner sleeve bearing
              retaining ring.                                         SECOND INTERMEDIATE SHAFT
         9.   Install the inner sleeve bearing and seal               To repair the second intermediate shaft (figure 19)
              spacer.                                                 after disassembly of the gearcase proceed as fol-
                                                                      lows:
         10. Install the collar on the clutch sleeve. Lubri-
             cate the splines ofthe clutch sleeve and gear
             sleeve and install the clutch sleeve on the
             gear sleeve.
         11. Install the jaw clutch hub key in the shaft. Be
             sure the key and hub keyway are free of nicks
             or burrs. Install the clutch hub on the shaft.
             The key should be filled so as to have BOtyl!
             contact on both side surfaces in both the
             shaft and the hub.
         12. Install the auxiliary reel bearing in the reel
             and install the reel on the hoist shaft.
         13. Reassemble the hoist shaft left bearing
             assembly by installing the bearing, bearing
             retaining ring, bearing seal, seal retaining
             ring and O-ring in the bearing housing.
(            Install the bearing assembly on the shaft. Be
             sure the O-ring is properly positioned in the
             housing.
         14. Install the hoist brake drum. Secure the drum
             with the gib key. The key should be fitted so               1.   RETAINING RING          9.   GEAR
             as to have 80tJ() contact on the wedge and side             2.   BEARING HOUSING        10.   GEAR BEARING
             surfaces. The drum should be located                        3.   HOUSING O-RING         11.   RETAINING RING
                                                                         4.   BEARING                12.   SPACER
             on the shaft so that the distance from the                  5.   RETAINING RING         13.   SPACER
             cen ter of the gear to the outer face of the drum           6.   CLUTCH HUB             14.   DOWEL
             is 22-3/8 inches.                                           7.   HUB SHIFTER COLLAR     15.   BEARING HOUSE
                                                                         8.   RETAINING RING         16.   BEARING
         15. Install the right bearing spacer on the hoist                           2ND INTERMEDIATE SHAFT
             shaft. Be sure the tapered end of the spacer is                                  FIGURE 19
             facing toward the bearing.
         16. Reassemble the hoist shaft right bearing                    1.   Lift the shaft assembly from the gearcase.
             assembly by installing the bearing, bearing                      Remove the dowel from the right shaft bear-
             labyrinth seal, seal retaining ring, and dowel                   ing housing.
             in the bearing housing. Install the bearing
             assembly on the shaft.                                      2.   Remove the retaining ring from the left shaft
         17. Install the right hoist sprocket. Secure the                     bearing housing. Remove the bearing hous-
             sprocket with the gib key. The key should be                     ing.
             fitted so as to give 80% contact on the wedge              3. Remove the left shaft bearing retaining ring
             and side surfaces. The sprocket should be                     from the shaft. Remove the left shaft bearing
             installed the same distance from the end of                   from the shaft.
(   --
             the shaft as the brake drum and sprocket
             were installed on the opposite end of the                   4.   Remove .the pulldown clutch hub from the
             shaft.                                                           shaft. Remove the shifter collar from the hub.


                                                     <> BUCYRUS-ERIE COMPANY. 1983                                          25

--- Page 5 ---
BI115923


                                                   CHAPTER!
(
                                               SECTION 4 - MAST

                   MAST STRUCTURE
        The 45-R drill mast (figure 33) is a fabricated struc-
        ture made of steel angles and formed plates. The
        structure is formed by four vertical angles tied
        together on three sides with angle lacing. The
        fourth side is open to allow the rotary drive unit to
        be raised and lowered the length of the mast.
        Inspect the mast structure daily for wear or dam-
        age. Inspect all mast ladders and platforms for
        loose hardware and structural integrity. Inspect
        the racking on the inside of the rear mast angles
        for proper lubrication and any wear or damage.
        Inspect the mast hinge pins and the structure sur-
        rounding the pins for wear or damage. Verify that
        the hinge pin keepers are in place and tight.
        Inspect the mast hoist cylinder attachments for
        wear or damage. Lubricate the pins weekly with
        the appropriate grease. Inspect the mast lock pins
(       for wear and damage. Verify that the lock pin
        keepers are in place and secured with the required
        cotter pins.
        Every 80 operating shifts lower the mast and
        inspect all welds thoroughly for cracks or damage.
        Clean the racking on the inside of the two rear
        mast angles and check the welds securing the
        racking to the angles. While the mast lock pins are                              WEDGE TYPE LOCKING
        removed from the machine check the pins and pin                                  ON SOME MACHINES
        bores for wear. Replace the pins and remachine
        the bores if clearance become excessive.
        REPAIR
        Repair of the mast structure is limited to repair
        welding of cracked or broken welds or components
        or replacement of severely damaged structures.
        Refer to the REPAIR WELDING topic in the
        APPENDIX for the exact procedures involved in
        repair welding of the mast.
        When repairing mast structures by welding it is
        important to keep in mind that the repair should
        return the structure to its original condition. All
        welds should be smooth and any notches or under-
        cuts should be welded and ground. Do not add
    (   reinforcing material or change the geometry of the
        structure. Replace any damaged components with                                 MAST
        material of the same strength and cross section.                              FIGURE 33


                                                      .. BUCYRUS-ERIE COMPANY, 1983                      45

--- Page 6 ---
BI115923


    2.   Lower the tool rack to its lowest position and              9.   Remove the pin securing the lower arm pivot
         rest it on the lower stop. Lock and tag all                      pin to the arm. Remove the bearing blocks
         controls to prevent unauthorized operation.                      from the pivot pin and remove the pivot pin
(                                                                         from the lower arm.
    3.   Disconnect the air line leading to the pipe
         gate operating valve.                                    10.     Inspect all components. Replace worn or
                                                                          damaged components as necessary. Remove
    4.   Disconnect the hydraulic cylinder by remov-                      the bushings from the bearing blocks and the
         ing the rod pin cotter pin and rod pin. The                      upper and lower support arms and replace.
         hydraulic cylinder may be retracted to gain                      Lubricate all pins and bushings.
         better access at this time.
                                                                  1I.     Reinstall the tool rack in reverse order of dis-
    5. Using a suitable crane and rigging support                         assembly. Make sure all pins are secured
         the tool rack. Remove the pins securing the                      with the proper retainer pins.
         tool rack to the upper and lower support arms
         and remove the tool rack from the machine.               12.     Check the operation of the tool rack and lu-
                                                                          bricate all lubrication points.
    6. Using a suitable crane and rigging support
         the upper support arm. Remove the bolts sec-                            TOOL WRENCHES
         uring the bearing blocks to the mast and
         remove the upper support arm from the                    The tool wrenches (figure 48) are use to clamp the
         machine.                                                 drill pipe in order to break a pipe joint. The tool
                                                                  wrenchs are two specially built hydraulic cylind-
    7.   Remove the pin securing the upper arm to the             ers operating inside a square casing. A spring
         arm pivot pin. Remove the bearing blocks                 loaded pawl engages a pocket in the drill pipe to
         from the pin. Remove the pin from the arm.               prevent rotation of the pipe.
    8.   Using a suitable crane and rigging support               Inspect the tool wrenches daily for loose or miss-
         the lower support arm. Remove the bolts sec-             ing hardware, or any wear or damage. Inspect the
         uring the bearing blocks to the mast and                 wrenches each shift for proer operation. Check
(        remove the lower support arm from the                    each wrench and associated hydraulic lines for oil
         machine.                                                 leaks and repair any leaks found immediately.


           653


                                                         10

                                     1


                   1.   BEARING BLOCK          7. CYLINDER BODY                 13.   ROD PACKING
                   2.   BLOCK BOLT             8. PACKING HOUSING               14.   ROD GUIDE
                   3.   CYLINDER GUIDE         9. HOUSING O-RING                15.   RETAINING RING
                   4.   RETAINING COLLAR      10. PACKING                       16.   PAWL
                   5.   COLLAR BOLT           11. CYLINDER CAP                  17.   PAWL RETAINING PIN
                   6.   PISTON ROD            12. CAP OIL SEAL                  18.   PAWL OUTER SPRING
                                                                                19.   PAWL INNER SPRING

                                                   TOOL WRENCH
                                                         FIGURE 48


                                               @   BUCYRUS-ERIE COMPANY, 1983                                          67

--- Page 8 ---
BI115923


                                                   CHAPTER 3
(
                                SECTION 1- SYSTEMS OPERATION

                          GENERAL                                             AUXILIARY AIR SYSTEM
        The 45-R drill is equipped with two independent               The auxiliary air system (figure 62) supplies com-
        air systems. The main air system (bailing air)                pressed air for control purposes. It supplies air for
        supplies air to clean the drilling chips from the             brakes, clutches, valves and other air activated
        hole. The auxiliary air system supplies air to oper-          devices. It consists of the auxiliary air compressor,
        ate various controls on the drill.                            main and auxiliary air tanks, pi ping, con troIs and
                                                                      the air activated devices. Most systems usually
                                                                      also include some type of antifreeze system and/ or
                                                                      an air dryer. Air passes from the compressor to the
                                                                      main air tank. The air then passes from the main
                                                                      air tank to the auxiliary air tank and finally to the
                                                                      air controls and air activated devices. The system
                   MAIN AIR SYSTEM                                    is protected from and monitored for failure by·
                                                                      safety valves, check valves and pressure switches.
        The main air system (figure 61) supplies com-                 Normal operating pressure in the auxiliary air
        pressed air for bailing the hole during drilling. The         system is maintained between 110 and 125 psi.
        air also cleans and cools the bearings in the bit.
        The air is compressed by a rotary vane air com-
        pressor or optional screw air compressor. Inlet air
        passes through a filter before entering the com-
(       pressor. Compressed air leaving the compressor
        flows through the main air line and through an                                      SAFETY
        unloader directional valve to the mast air pipe.
        When the main air valve is activated a butterfly               Whenever work is to be done on the compressed air
        valve in the mast air pipe is opened and the air               system, there are three important safety rules to
        flows through the main air piping and unloader                 follow:
        valve to the air seal connection ofthe rotary gear-
        case. It flows down through the drill pipe, through             1.   Turn the air compressor switch in the opera-
        the bit and out of the hole, carrying out the cut-                   tor's cab to the "off' position and attach a
        tings. When the main air valve is deactivated, the                   warning tag to the switch.
        unloader directional valve exhausts the air through             2.    Open the auxiliary power circuit breaker and
        a muffler to the atmosphere. When the machine is                      attach a warning tag to the breaker.
        equipped with a vane compressor, it also closes a
        butterfly valve on the inlet side of the compressor.            3.    Drain the air from the air tanks and air lines.


    (

                                                     © BUCYRUS-ERIE COMPANY, 1983                                        87

--- Page 9 ---
BI115923


c


                                                                                        1, Stuffing box;;,
                                                                                        2. Packing ; ; ;
                                                                                        ~;StuttJn9;b:o)(?gl~rp< ;'

                                                          FIGURE 83

(
    4.    Through the tapped ports on the discharge
          side of the cylinder, insert brass shims .002
          inches thicker than the rotor bottom
          clearance. This will take the rotor weight off
          the bearing inner races.
     6.   Proceed to the inboard head. Use the jack
          screws to remove the head evenly. The outer
          bearing rack with the rollers will come away
          with the heads. The dowels will remain in the
          cylinder when the heads are removed.
     6.   At this time, remove the rotor blades from the
          rotor shaft before the rotor is removed. Slide
          the rotor and shaft out of the cylinder as care-
          fully as possible to avoid any damage. The
          compressor is now dismantled.
     7.   Thoroughly inspect the inner cylinder. If
          washboarding wear (figure 84) is evident and
          is not deeper than .002 inch or .003 inch, this
          can be removed by polishing with emery. If                                   FIGURE 84
          washboarding is severe enough to rebore, a
          maximum of .060 inch can be removed from
          the diameter.                                           necessary for a long time. Two conditions usually
(   If the compressor is maintained properly from the
                                                                  make overhaul necessary. One is poor main-
                                                                  tenance, the other is excessive washboarding.
    beginning of use, overhaul should not become                  Poor maintenance includes improper lubrication


                                                 ® BUCYRUS-ERIE COMPANY, 1983                                        107

--- Page 10 ---
BI115923


    The eleP1ent should be replaced as follows:                     6.    Keep spare primary and safety elements on
                                                                          hand at all times. Store the elements in a
     1.   Loosen the wing nut. Remove the nut and                         protected area where they will be free from
(         gasket washer.                                                  damage, dirt and moisture.
     2.   Carefully remove the primary element (clean               7.    Handle all filter parts with care.
          or replace, if necessary, as described above).
                                                                   MAINTENANCE SCHEDULE
     3.   Remove the cotter pin and service indicator
          wing nut holding the safety element in place.            The following is the recommended maintenance
          Remove the element.                                      schedule for the screw compressor.
     4.   Carefully slide a new safety element inside              Daily or Every 8 Hours Operation
          the filter housing. Install the service indica-
          tor wing nut and tighten. Install the cotter              1.    Check the receiver oil reservoir level with the
          pin.                                                            compressor off and the drill in a level posi-
                                                                          tion. Add oil if required. Maintain the oil level
     5.   Carefully slide the primary element into the                    within the level gauge bullseye. If oil con-
          filter housing. Install the gasket washer and                   sumption is high, refer to topic COMPRES-
          tighten the wing nut until the element is                       SOR OIL SEPARATOR AND EXCESSIVE
          secure against the filter housing.                              OIL CONSUMPTION troubleshooting sec-
                                                                          tion.
    During intervals between servicing of the filter
    elements, perform the following inspection:                     L'... CAUTION: Compressor must be shut
                                                                   . . down and reservoir at zero pressure be-
     1.   Check to make sure that the filter inlets are            fore checking and adding oil.
          clean and not clogged with paper; rags or
          other debris.                                              2.   Drain the condensate from the receiver before
                                                                          compressor start-up when the oil is cold. Shut
     2.   Check the connections between the filter and                    off the drain valve when oil appears.
(         compressor inlet to make sure that all of the
          clamped and bolted connections are tight                   3.   After start-up, check service indicators on
          and leakproof.                                                  inlet air filters, oil filters and oil separator. If
                                                                          indicators are completely red while running,
     3.   Check the "Vacuator" ejector valve to make                      oil filter elements and oil separator must be
          sure that is not plugged or damaged and is                      replaced and air filter primary element must
          sealing properly around the filter housing                      be cleaned or replaced. Refer to topics OIL
          cups.                                                           FILTER ELEMENT AND OIL SEPARA-
                                                                          TOR REPLACEMENT and AIR FILTER
    WARNING: Do not operate without a "vac-                               ELEMENT CLEANING AND REPLACE-
    uator" valve on the filter since this will                            MENT.
    cause short element life.
                                                                     4.   Observe if the compressor loads and unloads
                                                                          properly.
    In addition to the above, the following precautions
    should be observed in the servicing of the air fil-              5.   Observe the discharge air pressure, discharge·
    ters:                                                                 air temperature and oil injection tempera-
                                                                          ture. If the air pressure exceeds either the
     1.   Do not oil either the primary or safety ele-                    rating plate pressure when loaded or is 15
          ment before installing.                                         psig above the rating plate pressure when
     2.   Do not wash the elements in other cleaning                      unloaded, discharge air temperature exceeds
          fluids.                                                         200°F, or injection oil temperature exceeds
                                                                          150°F, refer to TROUBLESHOOTING sec-
     3.   Never operate the compressor without both                       tion.
          elements installed.
                                                                   Every 125 Hours of Operation
     4.   Never use elements that are damaged, rup-
          tured or wet.                                            Check for dirt accumulation on radiator oil cooler
                                                                   core faces and on fan motor. Blow off dirt if
     5.   Never use elements with damaged gaskets.                 accumulation is excessive.


                                                 '" BUCYRUS-ERIE COMPANY. 1983                                          127

--- Page 11 ---
BI115923


(


                                  5
                                  4

                                  3


(                                                     7

                                                      9
                                                                                                                            7


                                                                                                                           10


                                                                                                       8    11


    LUBE NO. OF POINTS TYPE                    HOURS              AS  (OPTIONAL)
                                                                                                  COMPONENTS
    POINT LUBRICATED LUBRICANT 8          40    160       1000   REQ. AUTOMATED
       1         2         MPG        X                                        X         SHIPPER SHAFT BEARINGS
       2         2         MPG        X                                        X         IDLER SPROCKET BEARINGS
       3         1         MPG        X                                        X         VERTICAL SHAFT UPPER BEARING
       4         1         MPG        X                                        X         AIR SWIVEL SEAL
       5         1         MPG        X                                        X         AIR SWIVEL
       6         2         MPG        X                                        X         RACK PINIONS
       7         6         MPG                              X                            CENTER GUIDE SHEAVES
       8         4         MPG                              X                  X         CENTER GUIDE JAW BUSHINGS
       9         1         MPG                              X                  X         CENTER GUIDE BELLCRANK BUSHINGS
      10         1         MPG                              X                  X         PILOT VALVE BRACKET
      11         1         MPG                              X                  X         PILOT VALVE CAM
      12         2         RWRL                                    X                     CENHR GUIDE ROPES
    NOTE: THE ABOVE FREQUENCIES FOR MANUAL LUBRICATION, IF THE MACHINE IS EQUIPPED WITH AUTOMATIC LUBE
          SYSTEMS THE FREQUENCIES ARE SET AT THE LUBE CONTROL STATION.
           ON AUTOMATIC LUBE SYSTEMS THE INJECTORS SHOULD BE SET AT FULL OPENING AT STARTUP OF A NEW MACHINE
           AND THEN READJUSTED AS REQUIRED.

(                                              MAST LUBRICATION - PART 2
                                                                  FIGURE 121


                                                          © BUCYRUS-ERIE COMPANY, 1983                                     147

--- Page 12 ---
BI115923


           PROBLEM                             CAUSE                                 CORRECTIVE ACTION


C   Hoist-Propel
    Transmission
    (cont.)
    Loss of hoist-propel          I. Electrical component failure               I.    Replace failed component.
    power.                             or out of adjustment.                          Make electrical adjustments.
                                                                                      Refer to Electrical Instruc-
                                                                                      tions Manual.
                                  2. Dragging propel brake.                     2. Adjust.
                                  3. Clutch failure.                            3. Repair.
    Hoist jaw clutch mal-         l.   Operator starting hoist motor            I. Use correct procedure.
    function or damage.                before engaging clutch.
    Cannot steer machine.         l.   Propel brakes out of adjust-             I. Adjust.
                                       ment.
                                  2. Propel brakes not engaging.                2. Check adjustment and action
                                                                                   of rotochambers and linkage.
                                  3. Control valve problem (no air              3. Repair or replace valve (check
                                     reaching rotochambers).                       air lines also).
    MAST
    Difficulty in pinning         I. Machine not level.                         l. Follow correct leveling proce-
    mast in vertical posi tion.                                                       dure.
(                                 2. Obstructions.
                                                                                2. Remove obstructions.
    Pipe rack latch will not      I.   Broken air line.                         I.    Repair or replace.
    release.
                                  2. Rotochamber frozen up.                     2. Remove any condensate,
                                                                                   check operation of anti-freezer.
                                  3. Rotochamber diaphragm rup-                 3. Repair or replace.
                                     tured.
    Retaining gate not hold-      I. Control valve not working                  I. Repair or replace.
    ing pipe in rack.                  correctly.
                                  2. Retainer cylinder spring                   2. Repair or replace.
                                     broken or cylinder broken off.
                                  3. Pin lost or sheared.                       3. Replace.
    MAIN AIR
    COMPRESSOR
    (VANE TYPE)                                                                                                 ,/

    Discharge air tem-            I. Excessive discharge air pres-              I. a. Reduce discharge pressure
    perature excessive                 sure when loaded.                                 by increasing drill bit ori-
                                                                                         fice size.
                                                                                      b. Check hoses and piping
                                                                                         for abnormal restrictions
C                                                                                        to air flow.


                                                '" BUCYRUS-ERIE COMPANY, 1983                                        167

--- Page 13 ---
BI115923


      APPENDIX A3 - PINION AND COUPLING INSTALLATION
     REMOVAL FROM MOTOR SHAFT                                  hazards caused by using solvents for clean-
(     h CAUTION: A properly mounted pinion
                                                               ing. Use away from sparks, heat or flame to
                                                               prevent fire or explosion. Follow the manu-
    . . or coupling will have an interference                  facturers instructions.
    fit with the shaft causing it to release sud-
    denly and violently when broken loose. Loose               Remove any scoring from either part. Spot the cold
    the shaft nut just enough to allow the pinion              pinion or coupling on the shaft by hand to obtain
    or coupling to free itself. The shaft nut will             at least a 75 percent fit. Check the fit with bluing.
    stop the pinion or coupling and avoid injury               Remove the pinion or coupling.
    to personnel.
                                                                 2. Break all sharp edges of the key and the key-
    WARNING: When removing the pinion or                            way with a fine file, so there will be a radius of
    coupling from a motor shaft, always use a                       about 1164 inch at each edge. Fit the key to the
    suitable puller to avoid causing damage to                      shaft, taking care to avoid upsetting the metal
    either the pinion, coupling, motor frame,                       of the shaft adjacent to the key. If previously

View the complete manual on HeyDownloads →