PDF Mechanical Maintenance Manual Cat Bucyrus 2570W Walking Dragline - 1 MB

Unlock the full potential of your Cat Bucyrus 2570W Walking Dragline with this in-depth mechanical maintenance manual.

It provides detailed procedures for servicing, repairing, and troubleshooting the complex mechanical systems of this massive machine.

This manual is designed for skilled technicians to ensure the dragline operates at peak performance and with maximum safety.

It's a critical resource for any mining operation.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
BI005545
© Bucyrus
All Rights Reserved


       BUCYRUS                      R


                      Technical Manual

--- Page 28 ---
BI005545


      ~
                                                          ~                            ~~:~CASELOWEROIL

                                                          ~                            VERTICAL SHAFT LOWER
                                                          •.                           SLEEVE
                                         t=o=f==I==1F==F=~=f==I==V=E==R==T=IC=A=L
                                                                               =S=H=A=F=T=L=O=W=E::::R~
                                                                        ••             BEARING


      -         ),~I==O=t==F=j:=~=F=l==j:=S~W~IN~G~G~E=:A=::RC==A=-SE=-=C=A=jP.
                                                          1265 GAL.
                                                          EO:                          MOTOR SHAFT UPPER
                                                          ~                            BEARING

                                                                                       SWING MOTOR

      • •                                                                              MOTOR COUPLING

                                                                                       'SWING MOTOR BRAKE


            (                                                                          INT. SHAFT UPPER
                                                                                       BEARINGS
                                                                                       VERTICAL SHAFT LOWER
                                                                                       BEARINGS

                    -                                                                  VERTICAL SHAFT LOWER
                                                                                       SLEEVE
                                                                                       SWING GEARCASE -                   CAP.
                                                                                       1265 GAL.

                                                          ~                            ~~:~CASE LOWER OIL


                  & _J
                        .Lr---------J.·
                                                          ~                            VERTICAL SHAFT LOWER
                                                                                       SLEEVE
                                         t===t==F==j=~=l==j:=~S::=W:::I':=N:::;G=G::=::=EA=:=R;::C=::=:=A::::S::::E=-:::::::C=:=A==P:::j.
                                                                                       1265 GAL.


                                           :J>      :J>   0       0     0     (fJ     • USE MPG FOR BRAKES EQUIPPED
                                           C (j) Z I Z                        ~       WITH GREASE FITTINGS USE MPO FOR
                                           ~JJ()rn()
                                           o        m     mom                 ;;:     BRAKES WITHOUT GREASE FITTINGS
                                           :s:      0     m       A     m     :J>
                                           »        c     <       0     <     Z
                                           ::1      :D    ~       l>    ~     c
                                                                              ."
                                           0        m     -<      r     -<    :J>
                                           r        0     .f>,.   -<    (Xl   o...,
                                           ~              CD       I    0     C
                                           mOO                          "'U   JJ
                                             "U I                       rn    rn
                                           ~-l            ~::t>G)::!
                                                               ~ ~            JJ
                                                                              (fJ

                                           m              :j m          Z     ;;:
                                           ;;:            Z:J>          Gl    :J>
                                           {j)            Cl      (j)   I     Z
                                                                              C
                                            I             I             0
                                                                              ~
                                                                  JJ
                                                          Orne
                                           o              C       0     JJ
                                           ...,"U         JJ      C     (fJ

                                           oZ             (fJ
                                                                  JJ
                                                                  rn
                                           :J>                    o
                                           r


                            LUBRICATION
                    SWING MACHINERY (4 UNIT SWING)
                                  FIGURE 112


120

--- Page 29 ---
BI005545


                                                               CENTER PINTLE
           \~=4:=----------j                        '"
                                                   F=1==I===I=1=l===F=======j


                                 ~~
                                                                          RACK AND SWING PINIONS
                         ,
                             '/Y;- ~ 1~==f==1=I===f==1========1
                     /       /   "0F=t=t=cF=f=~4==t=U=P=PE=R=A=N=D=L=O=W=E=R=R=AI=Ls==j
                               /
                                 /~f==j=j==I==l==I=I=======j
                                                    n            ~        ROLLER FRAME ROLLERS


    o
                                                              '"          CAM BEARING PINS

                                                                          UPPER CAM FRAME
                                                        ~
                                                                          SLIDING SHOE
                                                        ~                 TRUNNION BEARING

                                                                   I      PROPEL LINK
                                                        ~

                                                                          LOWER CAM FRAME
                                                        ~
                                                                          LOWER CAM FRAME
                                                        ~                 TRUNNION BEARING
                                                                          SLIDING SHOE
                                                        ~                 TRUNNION BEARING


                                                                          SHOE PIN LINK
\                                                       ~


                                                                         . SYSTEMS AP AND AW ARE
                                                                         ST ANDARD EOUIPMENT: B. C, H
                                                                         AND K ARE OPTIONAL


                                                        in
                                                        ,.~
                                                        Z
                                                        ,.o
                                                        :Il
                                                        o


                   LUBRICATION
        PROPEL MACHINERY (EARLIER MACHINES)
                     FIGURE 116 (CONT.)


                © BUCYRUS-ERIE COMPANY, 1985                                                    125

--- Page 30 ---
K                      LOWER DEFLECTION
                                                                                                 BI005545
                                                       ;'l                    TOWER BUSHING
                                         K                                    BOOM HOIST SHEAVE
                                         ;'l                                  BUSHING
                                                                 K            SUSPENSION LINK
                                                                 ;'l          BUSHING
                                                                 K
                                                                 ;'l
                                                                              SUSPENSION LINK PIN

                                                       K                      DEFLECTION SHEAVE
                                                       ;'l                    BUSHING
                                                                 K
                                                                 ;'l          A-FRAME BACK LEG PIN


                                                       K                      LOWER DEFLECTION
                                                       ;'l                    TOWER BUSHING


                                                       K                      DEFLECTION SHEAVE
                                                       ;'l                    BUSHING


                                                                  K           MAST DEFLECTION
                                                                  ;'l         SHEAVE BUSHING


                                                        K                     UPPER DEFLECTION
                                                        ;'l                   TOWER BUSHING
                                                                  K           HOIST ROPE ROLLER
                                                                  ;'l         BEARINGS


                                                                  K
                                                                  ;'l
                                                                              MAST CROSS TIE PIN

                                          K                                   BOOM HOIST SHEAVE
                                          ;'l                                 BUSHING
                                                                  K
                                                                  ;'l         INT SUSP. LINK BUSHING

                                                                  K           UPPER MAIN SUSP LINK
                                                                  ;'l         BUSHING
                                                                  K
                                                                  ;'l         INT. SUSP. LINK BUSHING

                                                                   K          LOWER MAIN SUSP LINK
                                                                  ;'l         BUSHING

                                                                        ~     DUMP ROPE

                                                                        K
                                                                        ;'l   DUMP SHEAVE PIN

                                                                        K
                                                                        ;'l
                                                                              REAR SLEEVE BUSHING

                                                                        K
                                                                        ;'l   REAR THRUST WASHER

                                                                        K
                                                                              SWIVEL THRUST WASHER


                                                                        i     HOIST ROPES

                                                                        K
                                                                        ;'l
                                                                              FRONT SLEEVE BUSHING


                                                                        K     BOOM POINT SHEAVE
                                                                              BEARING


                                                                              INT. SUSP. BUSHINGS


                                   >           0           0            0
                                                           z            z
                                   "i0         ~           ~            ~
                                   ~           ~           m            m
                                                           <            <
                                   ~           ffi         m            m
                                                                         ~
                                   ii          z             ~
                                                             <           <
                                   r
                                   c           '"ffi       i':
                                   ~                                     ~
                                   '"< in~ ~                             ~


                                   '"m-<   ~                             ~
                                                                         Z
                                   ~
                                           Z
                                               ~                         "0
                                               " "0
                                                                         I
                                    I                        I

                                   §                         ~           ~
                                   0
                                   z
                                   ~


                   LUBRICATION
      FRONT END EQUIPMENT (TRAPEZOIDAL BOOM)
                     FIGURE 120


130

--- Page 31 ---
BI005545
 2. Empty drum.                                     heater can be supplied for use at the control panels
 3. Monitor broken supply lines and shut-off sys-   and pumping stations, and thermostatically con-
    tems if such should occur.                      trolled heating tape can be supplied which can be
                                                    wrapped around the lubrication lines.
 4. A vent monitor in systems A and L which
    gives warning if the system does not vent
    properly.                                        LUBRICANT DRUM HANDLING
The alarm system will be both visible and audible      EQUIPMENT (OPTIONAL)
at the control panel and in the operator's cab.     As optional equipment an electric hoist can be
  COLD WEATHER EQUIPMENT                            supplied to lift lubricant drums from the ground
        (OPTIONAL)                                  onto the machinery deck. Also air operated eleva-
                                                    tor hoists can be supplied at each pumping station
As optional equipment for cold weather radiant      to facilitate the changing of drums of lubricant.


136

--- Page 32 ---
BI005545


      PROBLEM                               CAUSE                             CORRECTIVE ACTION
                            LUBRICATION SYSTEMS (continued)

13. Excessive lubricant     Piston and plunger packings                  Replace packing.
    output through          worn.
    injector.
14. Reduced pressure        a. Diaphragm swollen or stiff.               a. Replace diaphragm.
    through air line
    regulator.              b. Inner valve disc dirty or worn,           b. Clean and/or replace.
                               or seat scored.
                            c.    Restricted air flow.                   c.   Clean filter and open supply
                                                                              valve.
15. Excessive pressure      Dirty air filter cone.                       Clean.
    drop through air line
    filter.
16. Clogging of air line    Over-lubrication.                            Reduce oil feed rate by turning
    lubricator.                                                          knob to lower setting.
17. Restricted air flow     Flattened or kinked lines.                   Bend or twist lines carefully to
    through air lines.                                                   relieve restriction.
                                                                         Make sure all plugs, sockets,
                                                                         nipples and tees are free from
                                                                         restrictive defects.
18. Power loss in           Electrical failure.                          Examine all relays, timing units,
    controls.                                                            disconnect switches and limit
                                                                         switches; verify all electrical
                                                                         connections and check wiring
                                                                         insulation.

                                 AIR SYSTEM - AIR COMPRESSOR

1. No air pressure.         a. Leaks in system.                          a. Check for leaks and repair.
                            b. Defective compressor or                   b. Repair or replace.
                               switch.
                            c.    Overload tripped.                      c.   Inspect compressor and motor,
                                                                              correct the cause, reset.

 2. Frequent starting       a. Leaks in system.                          a. Check for leaks and repair as
    and stopping of                                                         necessary.
    compressor.
                            b. Frozen lines.                             b. Clear frozen lines; make sure
                                                                            anti-freezer is operating
                                                                            correctly.
                            c.    Switch set incorrectly.                c.   Check setting, adjust as
                                                                              necessary. Check valve leak-
                                                                              ing internally.

 3. Compressor over-        a. Pump running backwards.                   a. Check motor rotation and
    heating.                                                                change connections if
                                                                            necessary.


                                          © BUCYRUS-ERIE COMPANY, 1985                                      141

--- Page 33 ---
BI005545
      PROBLEM                            CAUSE                   CORRECTIVE ACTION
                                                 BOOM
1. Cracks in boom           Overload.                         Consult Bucyrus-Erie Company
   foot, chords, lacings,                                     Service Department before unaer-
   deflection sheave                                          taking repair welding.
   towers or boom
   point.
2. Activation of pres-      Crack in main longitudinal or     Track air leak from chord with
   surized warning          apex chords.                      sonic detector and consult
   system.                                                    Bucyrus-Erie Company Service
                                                              Department before undertaking
                                                              repair welding.
3. Deflection and boom      Lubrication deficiency and part   Check all manual and automatic
   point sheaves do not     failure.                          lubrication systems. Inspect all
   rotate freely.                                             bushings, bearings, shafts, and
                                                              spacers. Replace if necessary.
4. Broken or damaged        Excessive loading.                Replace. Be sure to apply SRWL
   upper boom struc-                                          to protect the coating on the sup-
   tural strands or                                           port or structural strands.
   tower support                                              If intermediate boom structural
   structural strands.                                        strands are replaced load them
                                                              with the take-up device. Refer to
                                                              Appendix for values.
5. Handrails, plat-         Damaged welds or missing parts.   Repair weld or replace parts.
   forms, catwalks, or
   stairways.
                                        DRAGLINE BUCKET
1. Cracks in shroud,        Overloads, shock.                 Preheat, torch, and repair weld.
  clevis plates, side                                         Refer to Appendix for repair
  and bottom plates,                                          welding information.
  lip and arch.
2. Abrasion, cracking       Excessive wear patterns.          Hardsurface or replace.
   or shearing of tooth
   tips.
3. Worn tooth horns.        Wear.                             Check sides and slopes of tooth
                                                              horn with template and rebuild if
                                                              necessary. Refer to Appendix for
                                                              repair welding information.
4. Severe wear or           Overload.                         Use repair links.
   breakage of chain
   links in rigging.
5. Pivot and swivel         Overload. Severe jerking and      Restore mountings and lubricate
   mountings on             frictional rubbing.               at periodic intervals.
   rigging break.


146

--- Page 34 ---
BI005545
TURNOFTHENUTMETHOD                                       (1) Tighten to values listed =+= 101PiI. The torque
                                                               values listed are calculated for 2Qi,\'(, X proof
WARNING: This tightening procedure is good                     load with lubricated threads and under the
only for bolt grades 5 and 8 with UNC                          head surfaces of the bolt and nut.
threads. For bolts with other than UNC
threads contact the Bucyrus Erie Service                  2. The nuts and bolts should then be matched
Department.                                                  marked by center punching the bolt end and
Also, when using this procedure the bolt threads             nut. On rod bolts match mark both rod ends
and the surfaces under the bolt head and nut must            and nuts. The bolts and nuts should then be
be lubricated.                                               tightened additionally by the applicable
This procedure is applicable only if the joint and           amount of nut rotation as specified in Table 4.
under head surfaces for bolt and nut are machined            It is not necessary to follow any particular bolt
for parallelism.                                             to bolt sequence during this portion of the
                                                             "turn of the nut" tightening.
 1. The bolts shall be brought to a "snug tight"
    condition to insure that the parts of the joint      NOTE: Nut rotation is read between punch
    have good contact with each other. "Snug             mark on the bolt and punch mark on the nut.
    Tight" is defined as the tightness attained by       For rod bolts, nut rotation is the cumulative
    torquing a bolt to the value specified in Table 3    total rotation between punch marks on both
    below. Snug tightening should progress sys-          ends of the rod bolt.
    tematically from the most rigid part of the
    joint to its free edges, alternating from bolt to
    bolt to assure gradual even pull up of the mat-                            TABLE 4
    ing parts. After all bolts have been snugged,         Part No.        Nut Rotation       Bolt Length (1)
    the first bolts tightened at the most rigid part
    of the joint should be rechecked for proper           747773-01 1/3 Turn of ± 10% Up to and
    torque. If these bolts are loose due to pull up of                                including 4
    the joint, the snug tightening sequence should                                    diameters.
    be repeated for all bolts in the connection. This     747773-02 1/2 Turn of± 10% Over 4 diame-
    rechecking and re-torquing procedure should                                      ters but not
    be repeated as many times as is required until                                   exceeding 8
    the joint is completely pulled up and all bolts                                  diameters
    are at the specified "snug tight" torque. Tight-
    ness of the mating surfaces of the joint should       747773-03      2/3 Turn ± 10%     Over 8 diame-
    then be verified by using feeler gauges.                                                ters but not
                                                                                            exceeding 12
                                                                                            diameters
               TABLE 3
     "SNUG TIGHT" TORQUE VALUES                          (1)   In case part number or nut rotation designa-
                                                               tion is not given, the nut rotation can be
       Bolt Dia.            Torque Values (1)
                                                               determined by the bolt length (Grip length +
     In.       Cm.          Ft. Lbs.    Nm.
                                                               1/2 bolt diameter). For bolt lengths exceeding
    .500        1.27            15             20              diameters contact the Bucyrus-Erie Service
    .625        1.58            30             40              Department.
    .750        1.90            53             71
    .875        2.22            86            116
   1.000        2.54           128            173
   1.250        3.17           224            303
   1.500        3.81           390            528
   1.750        4.44           457            619
   2.000        5.08           688            932
   2.250        5.71          1005           1362
   2.500        6.35          1375           1864
   2.750        6.98          1864           2527
   3.000        7.62          2462           3337


4A

--- Page 35 ---
BI005545


               APPENDIX A5 - MAINTENANCE WELDING

    SECTION 1 - REPAIR WELDING OF BASE, REVOLVING
   FRAME, A-FRAME, WALKING SHOES AND DRAG BUCKET

                  GENERAL                                   part of the design can reduce fatigue strength
                                                            because of the change in geometry from the origi-
These recommendations for repair welding apply              nal structure.
to the major structural members of the machine
including the base, revolving frame, A-frame walk-            RECOMMENDED ELECTRODES
ing shoes, and drag bucket.                                        AND PREHEAT
The high cyclic loading characteristics of the              Effective repair welding ofcracked, broken or bent
walking dragline are considered in the design and           structural members ofthe machine involves knowl-
material selected for the construction of the ma-           edge of the types of steel used, proper welding
chine. However, due to unusual operational condi-           electrodes and recognized good welding practice.
tions that may be encountered and to the great              The chemical composition, mechanical properties
number of cyclic loadings that may be applied to            and thickness of the steel determine the welding
the machine, fatigue cracks or other abnormali-             electrode to be used and the preheat temperature
ties may occur. Early detection ofthese conditions          required. Refer to Table 1 for types of steel used in
through regular machine inspection helps to avoid           the structures and recommended electrode and
problems or emergency breakdowns.                           preheat.
Maintenance welding is applied to the repair of                     WELDING ELECTRODES
cracked, broken or bent structural components.
Reconditioning of failed members requires atten-            With the exception of the boom and mast, weld
tion to a number of details and careful application         repairs on the various structures of the machine
of the repair procedure. Only in certain cases is it        made with two basic classifications of shielded
necessary to strengthen members by added rein-              metal arc electrodes, namely E7018 and E8018-Cl.
forcement.                                                  Both are low hydrogen electrodes which deposit
                                                            weld metal having excellent properties at strength
WARNING: Such modifications should be                       levels with 70,000 to 80,000 pounds per square
made only upon recommendation by Bucyrus-                   inch, and impact properties from ·20 degrees Fah·
Erie Company. Improperly applied reinforce-                 renheit to -75 degrees Fahrenheit. These are all
ments can have an adverse effect on the per-                position electrodes which produce high quality
formance and life of the structure.                         welds for repairing the structural components of
                                                            heavy machinery.
A broken member is best repaired by making a
complete penetration weld, preferably by welding           NOTE: Although these electrodes are of
from both sides, using the correct welding elec-           superior quality, care must be exercized in
trode and observing all precautions, such as pre-          their application. Low hydrogen electrodes
heat, back-gouging, etc. The complete penetration          are highly susceptible to moisture pick-up
groove weld should be ground flush with the base           after removal from sealed containers. To
metal on both sides to remove all surface irregular-       maintain low hydrogen, that is, crack res-
ities. An alternate procedure incorporates back-up         istant properties, they must be stored in
bars to ensure sound, complete penetration welds           electrode ovens at 250 degrees Fahrenheit
in the repair area. Be sure to follow all applicable       up to the time of use. Small portable rod
safety measures and federal, state and local regu-         ovens at the welder's side are ideal. Use of
lations.                                                   dry low hydrogen electrodes cannot be over-
                                                           emphasized.
The reason for favoring a complete penetration
weld repair conditioned by grinding, instead of            Cracks caused by hydrogen are extremely fine and
adding reinforcement, is to maintain the original          occur invisibly below the surface in the base metal
pattern of stress flow, designed into the structural       heat affected zone, as shown in figure 125. There-
members. Addition of reinforcement which is not            fore, they are not detectable at the timeofwelding.


                                          © BUCYRUS-ERIE COMPANY, 1985                                     IIA

--- Page 36 ---
BI005545
pass to remove all slag before continuing. Grind to             REPLACEMENT OF BUCKET LIP
remove any undercut or other defects which occur                    CENTER SHROUDS
during welding.
Maintain the preheat until arc gouging and weld-                     BLENDTOO          ~

ing has been completed. Arc-air gouge to half
thickness. Prepare a V groove for welding. Weld            ~~~~~ ~ ~
this half completely. Turn bucket over. Arc-air
gouge to completely remove the crack from the
                                                                                           ~
second side and prepare a V groove for welding as
before.

STRESS RELIEVING
On major repairs, such as a broken lip or one
                                                                                           e
which has cracked through the thickness, thermal
stress relieving is recommended after welding.
Stress relieving is beneficial in removing residual
weld stresses, reducing hardness in the weld area,
restoring ductility and aids in removal of hydro-
gen from the metal.
Electrical resistance heating with thermocouple
temperature control is recommended. The area to
be heated should include several inches on either
side of the repair and should extend the full depth
of the lip from leading edge to the basket. Heating        1"   2"
elements, however, should not be placed over the
plate of the basket. Thermocouples should be
placed over the weld in the area of the thickest and
                                                         lo WE~BLEND            TO 0


thinnest portions of the lip.
                                                                          FIGURE 130
Rate of heating and cooling must be controlled to
avoid drastic temperature differences in the metal.
Up to 600 degrees Fahrenheit, the lip can be           Install center shrouds according to welding details
heated at the maximum rate attainable with the         to welding details shown in figure 130. Install
equipment. Over 600 degrees Fahrenheit, the rate       corner shrouds and shroud plates according to
                                                       welding details shown in figure 131.
of heating should be restricted to 100 degrees Fah-

View the complete manual on HeyDownloads →