PDF Maintenance Manual Raymond Transtacker TRT - 4 MB

Keep your Raymond Transtacker TRT performing at its best with this official maintenance manual.

Designed for models with serial numbers TRT-03-00100 and up, it details all scheduled maintenance procedures.

Following these factory-recommended guidelines is crucial for preventing breakdowns and ensuring safe operation.

This manual is an essential tool for service technicians responsible for warehouse equipment upkeep.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram ✉Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
The Raymond ® Transtacker

Maintenance Manual


Model                      Serial No.
TRT                      TRT-03-00100 and up


Publication PDMM-0092A        Issued: 30 September 2004
Publication PDMM-0092B        Updated: 01 March 2005
Publication PDMM-0092C        Re-Issued: 30 September 2006
Publication PDMM-0092D        Updated: 01 August 2007
Publication PDMM-0092E        Re-Issued: 20 September 2013

--- Page 3 ---
The Raymond ® Transtacker Maintenance Manual                          Service Information Documents List


Service Information Documents List
The following Service Information documents (RSBs, RPINs, and RSIs) have been incorporated into
this manual.

Use the blank rows below to log Service Information documents when they are added to this
manual.


 Document Number       Subject                                                   Date

 RSB TRT-08-003        Solid State Control Handle Knobs Sticking                 December 3, 2008

 RSB TRT-09-001        Overspeed Device Torque Limiter Interference              April 15, 2009

 RPIN TRT-09-R002      Upper Mast Limit Switch                                   June 23, 2009

 RPIN TRT-10-R001      Carriage Roller Inspection                                August 22, 2010

 RSI TRT-13-001        Steer Motor and Steer Controller Change                   April 8, 2013

 RSI TRT-13-002        Hoist Brake Fails to Release                              June 25, 2013


Publication PDMM-0092, Issued: 30 September 2004                            Page Revised 9/20/13 xi

--- Page 4 ---
The Raymond ® Transtacker Maintenance Manual       Section 2. Safety


Section 2. Safety


Publication PDMM-0092, Issued: 30 September 2004                2-1

--- Page 5 ---
The Raymond ® Transtacker Maintenance Manual         Section 2. Safety

                                                   AC Electrical Safety

AC Electrical Safety


  If the red lights on the operator display
  and the AC power distribution
  compartment light up, do not step out of
  the truck or reach out to touch the
  racking. Drive the truck out of the aisle
  on battery power, or shut OFF the AC
  power to the overhead conductor bar
  system before dismounting from the
  vehicle. Repair the ground loss before
  placing the truck back in operation.


  The voltage levels on this truck can be at
  a potential of up to 600 volts AC above
  ground. High voltage can cause serious
  injury or be fatal. Always disrupt input
  power, unless it is required, before
  performing maintenance procedures.
  If power is required to perform specific
  procedures; follow good electrical
  practices, applicable electrical codes,
  and the contents of this manual.


Publication PDMM-0092, Issued: 30 September 2004                 2-11

--- Page 6 ---
The Raymond ® Transtacker Maintenance Manual                            Section 3. Systems Overview

                                                                                          Hoist System

automatically reduce the voltage to B3 to 13 to     pulses and applies them to an externally
16 percent of it's input voltage but holding B3     mounted resistor where the pulses are
energized at a lower power level and preventing     dissipated as heat. This process is called
it from overheating. The B3 solenoid activates      “Dynamic Braking.”
the hoist brake manual release plunger
mechanism that releases the hoist brake, and        The Hoist Motor (MH) is located on top of the
allows the carriage to lower. The Tractor PLC       gear reduction unit at the front of the truck. It
(NA) automatically toggles the DC Lowering          is a 3-phase, 60 Hz, 30 Horsepower, 480 VAC
Contactor off after approximately one second.       (typical) squirrel cage motor with an integral
This allows the hoist brake to re-apply and stop    cooling fan. It is inverter duty rated. A
the carriage from lowering. This is necessary       thermostat is encapsulated within the stator
because when the hoist brake remains released       windings. This thermostat “opens” at
too long, the carriage will reach a high enough     approximately 302°F (150°C) and causes the
lowering speed to engage the Drop-Stop              VFI to reduce power output. This results in
mechanism. This prevents any further use of         slower lift speeds until the motor cools
the Emergency DC Lowering feature until the         sufficiently, allowing the thermostat to reset.
Drop-Stops are reset.
                                                    The Hoist Gear Reducer is mounted to the
The Line Reactor (LR) assembly is located in the    foremost mast upright tube at the front of the
battery charger compartment at the front of the     truck. It is a triple reduction, right angle drive,
truck. It is mounted directly underneath the        helical bevel gearmotor that results in high
battery charger. The LR consists of three choke     efficiency, quiet running, and high reliability
coils. One coil is located in each leg of the       with high load carrying capacity. The gear
480 VAC power that is applied to the VFI. The       ratios vary from 40:1 to 60:1 depending on the
LR functions to smooth out any variations in        application. The oil capacity of the gearbox is
current, and to reduce any spikes that could        approximately 8 to 9 gallons. The two hoist
potentially damage the VFI.                         cable take-up drums (right and left) are
                                                    mounted on the output shafts at the sides of
The Hoist Motor Controller (VFI) is located in a    the gear reducer unit.
compartment at the front of the truck directly to
the right of the battery charger. The VFI is a      The Hoist Lift Cables are two independent,
microprocessor controlled Variable Frequency        oppositely wound cables, each having a
Inverter. In most North American applications,      minimum safety factor of 6:1, that support
the VFI is typically powered with 480 volt          the entire carriage assembly. These cables run
3-phase AC. The VFI rectifies the incoming AC       from the cable take-up drums, over the mast
to approximately 650 VDC. The VFI uses              sheaves, down and around the carriage
Insulated Gate Bipolar Transistor (IGBT)            sheaves, then up to the equalizing cable anchor
inverter bridge circuitry along with a special      bar. With the carriage fully lowered, two full
pulse-width modulation method with selectable       wraps of cable should remain on each take-up
pulse frequency to steplessly control the speed     drum.
of the 3-phase AC Hoist Motor (MH) without
regard to sudden changes in its connected load.     The Equalizing Hoist Cable Anchor Bar is
Nominal lift and lower speed is 90 feet per         located at the top rear of the mast. The pivoting
minute.                                             arrangement makes sure that each cable
                                                    supports the load equally.
During lowering operations and periods of
deceleration, the Hoist Motor delivers energy       The Drop-Stop system is a gravity operated
back into the VFI. This causes the 650 VDC link     brake that stops the vertical descent of the
voltage to increase. To prevent this voltage        carriage when its speed reaches 150% of the
increase from rising to levels high enough to       rated lowering speed and/or a hoist cable
cause damage, the VFI contains a “Braking           becomes slack. A centrifugal clutch, operated
Chopper” circuit that chops the overvoltage into    by a sprocket and a chain extending the full


Publication PDMM-0092, Issued: 30 September 2004                                                    3-9

--- Page 7 ---
The Raymond ® Transtacker Maintenance Manual                                Section 3. Systems Overview

                                                                                        Operator Displays

Operator Displays                                      Operator Display (OD2)
                                                       Operator Display OD2 is a LED backlit liquid
Two operator displays are used on The                  crystal display for viewing text messages. It is
Raymond Transtacker.
                                                       located at the rear of the left control arm and
                                                       provides the following functions:
Operator Display (OD1)                                   •   Displays error codes.
                                                         •   Supplies diagnostic information.
Operator Display OD1 is located at the end of
the right control arm, and provides the                  •   Performs the Learn procedures for the
following information:                                       Travel, Hoist, and Load Handler
  •     A steering display with 5 yellow LEDs and            potentiometers.
        1 green LED that indicate the position of        •   Performs Load Handler calibration
        the steerable wheel.                                 procedures (Fork Load Handler Only).
  •     A single green LED that, when lit,
        indicates the load handler is centered or in
        the ready for full speed travel position.
  •     A group of 4 red LEDs that, when lit,
        indicate the Earth Ground Verification
        Board was either not enabled or has
        detected an unreliable connection between
        the truck and the building AC power
        system earth ground.


      If the red lights on the operator display                                                          3
                                                       Figure 3-4.   OD2 Display
      and the AC power distribution
      compartment light up, do not step out
      of the truck or reach out to touch the           General Instructions
      racking. Drive the truck out of the aisle
      on battery power, or shut OFF the AC             Operator Display (OD2) interfaces with the
      power to the overhead conductor bar              Carriage PLC (NB). OD2 displays error codes,
      system before dismounting from the               provides diagnostic information, and performs
      vehicle.                                         various “Learn” procedures. Press the Shift key
                                                       first, then press the appropriate Function key,
                                                       F5 through F8, for the action you want to
                                                       perform. Refer to “Analog Diagnostics / Learn
                                                       Procedures” on page 3-20 for details on the use
                                                       of each function key.
                                                       NOTE: It is important to note that the truck
                                                                must be powered up (key switch ON) for at
                                                                least seven to ten seconds before
                                                                performing “Learn” procedures. All
                                                                Learned values will be lost and all control
                                                                handle potentiometer neutral positions
                                                                must be relearned if the truck was not
                                                                powered up for the seven to ten second
                                                                time period.
                                                  3
Figure 3-3.   OD1 Display


Publication PDMM-0092, Issued: 30 September 2004                                                      3-19

--- Page 8 ---
The Raymond ® Transtacker Maintenance Manual                                     Section 3. Systems Overview

                                                                                                   Special Tools

Changing a Parameter

To access parameters, use the Menu Navigation
key to select PROGRAM. Submenus organize the
parameter list. Scroll through the list and press
the right arrow on the Menu Navigation Key to
enter the sub-menu. Parameters available are
shown in Table 3-4.

Table 3-4.   Program Mode Adjustable Parameters

                                   Nominal
     Parameter         Range                      Units                        Description
                                   Setting

 M3 THRT BRK          60 to 100       80           %      Determines the “hardness” of the plugging when
                                                          transitioning from M4 to M3 (entering a slow flag).

 M2 Max. Speed         0 to 40        35           %      Sets maximum out of aisle speed.

 M3 Max. Speed         0 to 30        25           %      Sets maximum in-aisle creep speed for slow flag zone
                                                          or load handler not centered.

 M4 Max. Speed         0 to 100      100           %      Sets maximum in-aisle speed.

 M2 THRTL MAP          20 to 80       50           %      Determines the “hardness” of acceleration in Mode 2.

 M4 THRTL MAP          20 to 80       50           %      Determines the “hardness” of acceleration in Mode 4.


Publication PDMM-0092, Issued: 30 September 2004                                                            3-29

--- Page 9 ---
The Raymond ® Transtacker Maintenance Manual       Section 4. Scheduled Maintenance


Section 4. Scheduled Maintenance


Publication PDMM-0092, Issued: 30 September 2004                               4-1

--- Page 10 ---
The Raymond ® Transtacker Maintenance Manual                            Section 4. Scheduled Maintenance

                                                           Every 180 Days or 1000 Deadman Hours (HD)

Every 180 Days or 1000
Deadman Hours (HD)

                                 Every 180 Days or 1000 Deadman Hours (HD)

 Perform all 60-day/250-hour checks, including daily checks, plus the following:

   Item No.
 See “Scheduled
 Maintenance,
 Lubrication,        Component                                       What to do
 and Inspection
 Points” on
 page 4-14.

      16          Hardware              Check tightness of all hardware connecting wires and cables.
                                        Check bolt torque every 1000 hours.

      33          Lift Cables           Lubricate. Clean and swab entire length with lubricant. See
                                        “Lubrication Specification Chart” on page 9-5.

      34          Carriage Cam          Lubricate grease fittings. Apply two or three shots of lubricant at
                  Followers             each point. See “Lubrication Specification Chart” on page 9-5.
                                        Clean off old grease build-up.

      35          Pulley Sheaves        Check for binding or wobbling on axle shaft. Repair or replace faulty
                  (Upper and Lower)     sheaves per maintenance procedure on page 7-268.

       8          Drive Unit            Check mounting bolt torque. (Refer to page 7-84, step 2.)

      36          Pivot Points          Check drop-stop linkage, AC collector linkage, door hinges, and so
                                        on. Clean and apply a few drops of a lubricant, such as AeroKroil or
                                        equivalent, to all pivot points. See “Lubrication Specification Chart”
                                        on page 9-5.
                                        Check hoist brake manual release linkage to emergency DC lowering
                                        solenoid.

      37          Steer Actuator        Check mounting bolt torque. (Refer to page 7-34, step 3.)
                  (Motor) Mounting
                  Bolts

 Fork Load Handler Only

      51          Reach Motor           Check friction disc. Adjust and/or replace per maintenance
                  Brakes                procedures on page 7-221.
                                        Clean vent holes with low compressed air.

 Shuttle Load Handler Only

      61          Shuttle Motor         Check minimum disc thickness (3/32 in. or 2.3 mm).
                  Brake                 Check magnet air gap (0.045 to 0.100 in. or 1.1 to 2.5 mm).

      62          Fail-Safe Brake       Check air gap (0.008 to 0.012 in. or 0.203 to 0.304 mm).
                  (multiple shuttles
                  only)

      54          Shuttle Chains        Check for wear.


Publication PDMM-0092, Issued: 30 September 2004                              Page Revised 9/20/13 4-11

--- Page 11 ---
The Raymond ® Transtacker Maintenance Manual                                    Section 4. Scheduled Maintenance

                                                   Scheduled Maintenance, Lubrication, and Inspection Points


   54


                                                                        56
                                                                                                         4lube-rch.pcx
Figure 4-9.   Shuttle Gearbox Lubrication Points (view from underside of carriage)


Publication PDMM-0092, Issued: 30 September 2004                                                            4-21

--- Page 12 ---
The Raymond ® Transtacker Maintenance Manual                                     Section 5. Troubleshooting

                                                                                 Troubleshooting Procedure
GEN1:           General Troubleshooting


        GEN1: General Troubleshooting


          Gather as much
         information as you                                                           Eliminate unlikely
                                          What is the problem?
            can about the                                                                  causes.
              problem.
                                          Where did it happen?


                                          When did it happen?


                                          What functions are affected?

                                                                                      Select and prioritize
                                          What conditions trigger the problem?          the most likely
                                                                                            causes.


                                                                                          Check each
        Talk directly with the                                                        likely cause, using
                                                                                            Process
        operator or foreman.                                                            the tests in this
                                                                                            manual.


                                                                                         Check all other
        Operate the lift truck                                                           truck functions
             yourself.                                                                before returning the
                                                                                      lift truck to service.


          Using schematics
            if necessary,
              identify all
         components which
           could cause the
               problem.


                                                                                                          5GEN1.WMF


Publication PDMM-0092, Issued: 30 September 2004                                                               5-9

--- Page 13 ---
The Raymond ® Transtacker Maintenance Manual                                        Section 5. Troubleshooting

                                                                                           Fuses/Circuit Breakers

Fuses/Circuit Breakers
Test/Inspection
Examine for signs of overheating, discoloration,
cracking, or other physical damage.

To test a fuse, remove it from the vehicle or
isolate it from the electrical circuit by removing
all the connections from one side of the fuse.

Use a digital ohmmeter set on the lowest scale
and measure the resistance across the fuse.
The resistance should measure less than 1
ohm.

Fuse Locator Chart

Table 5-2.     Fuse Identification, Location, and Function

 Fuse          Amps          AC/DC                   Location                         Function

 FU1         350 A           DC          Drive Motor Compartment       Power Fuse, Travel
                                         (Contactor Panel)

 FU2         15 A            DC          Drive Motor Compartment       Steering Fuse (S/N 230 and below)
                                         (Tractor PLC Hinged* Panel)

 FU3         15 A            DC          Drive Motor Compartment       Steering Fuse (S/N 230 and below)
                                         (Tractor PLC Hinged* Panel)

 FU3         80 A            DC          Drive Motor Compartment       Steering Fuse (S/N 231 and Up)

 FU4         15 A            DC          Drive Motor Compartment       Control Fuse (B+)
                                         (Tractor PLC Hinged* Panel)

 FU5         15 A            DC          Drive Motor Compartment       Control Fuse, Travel Power (B–)
                                         (Tractor PLC Hinged* Panel)

 FU6         15 A            DC          Drive Motor Compartment       DC Function Fuse (slo-blo) (B+)
                                         (Tractor PLC Hinged* Panel)

 FU7         15 A            DC          Drive Motor Compartment       DC Function Fuse (slo-blo)
                                         (Tractor PLC Hinged* Panel)

 FU8         15 A            AC          AC Electrical Compartment     Rotate and Reach Motor Controller Fuse
                                         (Slide-out Panel)             (slo-blo) (Fork Load Handler)
                                                                       Shuttle Load Handler Enable Relay Fuse
                                                                       (Shuttle Load Handler)

 NOTE: * Tractor PLC Panel is not hinged on cold storage vehicles.


Publication PDMM-0092, Issued: 30 September 2004                                Page Revised 9/20/13 5-19

--- Page 14 ---
The Raymond ® Transtacker Maintenance Manual                           Section 5. Troubleshooting

                                                                     DC Lowering Troubleshooting

DC Lowering                                           approximately 0.75 second intervals. The
                                                      contactor tips should also close and open
Troubleshooting                                       at this rate. If this is not observed, use the
                                                      schematics in the Appendix section of this
                                                      manual to check for open conditions with
DC Lower Function Inoperative                         the DC Lowering Contactor (LC) coil and
                                                      associated wiring. Repair or replace as
 1. Check for +24 VDC at the Carriage PLC             necessary.
    (NB) input terminal NB-I-1.5 with respect
    to TS6-6, TS6-7, TS6-8 or other similar        5. If the desired results were obtained in step
    ground point when the DC Lower/Retract            4, check for B+ across both the +BAT and
    Switch (S17 on a Fork Load Handler                +AUX terminals with respect to the –BAT
    equipped truck or S18 on a Shuttle Load           terminal on the Control Module (CM2).
    Handler equipped truck) is activated. The         This voltage should toggle ON and OFF at
    corresponding green indicator LED for             approximately 0.75 second intervals. If
    NB-I-1.5 should be lit (ON). If +24 VDC is        this is not observed, use the schematics in
    measured and the LED does light, proceed          the Appendix section of this manual to
    to step 3. If +24 VDC is not measured and         check the wiring and connections from
    the LED does not light, check the S17 or          CM2 to LC-1 and TS9-1. Repair or replace
    S18 switch and associated wiring for              as necessary. Check LC tips for wear,
    continuity, poor connections, or damage.          burning, or pitting. Clean or replace as
    Repair or replace as necessary.                   necessary.
                                                   6. If the voltage to CM2 was correct, check
 2. If +24 VDC was measured but the green
    indicator LED for NB-I-1.5 is dark (OFF),         the wiring and connections from the WHT
                                                      and BLK terminals on CM2 to the DC
    replace the Carriage PLC (NB).
                                                      Lowering Solenoid (B3) for shorts, opens,
 3. Check for approximately +24 VDC at the            or damage. Repair or replace as necessary.
    Tractor PLC (NA) output terminal
    NA-Q-1.1 with respect to NA terminal M or      7. Check the resistance of the DC Lowering
    other similar ground point when the               Solenoid (B3). It should measure between
    lowering switch on the carriage is                2 and 3 ohms. Replace as necessary.
    activated. The corresponding output LED        8. The DC Lowering Solenoid (B3) requires
    should also be lit (ON). If approximately         approximately 16 amps to pull the plunger
    +24 VDC is measured and the LED does              full stroke and dropping to approximately
    light, proceed to the next step. The voltage      2 amps after 0.5 seconds to hold the
    and LED should toggle ON and OFF at               plunger in. Use a clamp-on ammeter to
    approximately 0.75 second intervals. If           check these current values if necessary.
    +24 VDC is not measured and the LED            9. Refer to the DC Lowering Solenoid (B3)
    does not light, disconnect the wire at            installation procedures on page 7-180 to
    NA-Q-1.1 and retest. If the voltage and           verify the mechanical adjustments are
    LED status are now good, use the                  correct.
    schematics in the Appendix section of this
    manual to check for shorted conditions
    with the DC Lowering Contactor (LC) coil,
    DA1, and associated wiring. Repair or
    replace as necessary. If the voltage and
    LED status are still wrong or they fail to
    toggle correctly, replace the Tractor PLC
    (NA).
 4. Check for approximately +24 VDC across
    the DC Lowering Contactor (LC). This
    voltage should toggle ON and OFF at


Publication PDMM-0092, Issued: 30 September 2004                    Page Revised 9/30/06 5-29

--- Page 15 ---
The Raymond ® Transtacker Maintenance Manual                                 Section 5. Troubleshooting

                                                                                         Symptom Tables

       Possible Cause                             Action

       Rotate Motor Controller (MC1)               1. Connect a digital voltmeter across the SIG
                                                      terminal (+) and the COM/EN terminals (–).
                                                      Operate the Load Handler Control Knob in both
                                                      the CW and CCW directions. The meter should
                                                      indicate voltage from 0 to +9.5 VDC and 0 to
                                                      –9.5 VDC depending on the direction of control
                                                      knob movement.
                                                   2. If this voltage measurement is observed, replace
                                                      MC1.
                                                   3. If this voltage measurement is not observed,
                                                      check the wiring and connections between MC1
                                                      and AD2.
                                                   4. Refer to the checks for the Load Handler Control
                                                      Potentiometer (VR4) if the wiring and connections
                                                      between MC1 and AD2 check good.

       Load Handler Control Potentiometer (VR4)    1. Connect a digital voltmeter across the AD2
                                                      module terminals C+ (+) and C– (–). The voltage
                                                      should measure between +2.0 and +3.0 VDC with
                                                      the control thumb knob centered (neutral
                                                      position). This voltage is nominally set to +2.5
                                                      VDC.
                                                   2. Move the control thumb knob slowly to its
                                                      extremes and hold it there while observing the
                                                      meter for any erratic fluctuations. The voltage
                                                      measured at the extremes should measure
                                                      between +0.5 and +4.5 VDC (ignore minor
                                                      variations).
                                                   3. If these voltages are not observed, replace VR4.
                                                   4. If these voltage measurements are obtained,
                                                      replace the Analog/Digital Module (AD2).
                                                   5. If the problem still exists, replace the Carriage
                                                      PLC (NB).


Publication PDMM-0092, Issued: 30 September 2004                         Page Revised 9/30/06 5-39

--- Page 16 ---
The Raymond ® Transtacker Maintenance Manual                             Section 5. Troubleshooting

                                                                                      Symptom Tables

       Possible Cause                          Action

       Reach Motor Controller (MC2) or the      1. Monitor the voltage across the output terminals
       Shuttle Motor Controller (MC1)              M1 and M2. The voltage should remain steady in
                                                   relation to the Control Knob position (ignore
                                                   minor variations). Maximum voltage is
                                                   approximately 90 VDC. The polarity depends on
                                                   the direction of rotation requested.
                                                2. If the output voltage varies and the Control Knob
                                                   is held steady, check the input voltage across the
                                                   SIG and COM/EN terminals. Maximum voltage is
                                                   approximately 9.5 VDC. The polarity depends on
                                                   the direction of rotation requested.
                                                3. If this voltage remains steady (ignore minor
                                                   variations), replace the Motor Controller (MC2) for
                                                   a Fork Load Handler equipped truck or MC1 for a
                                                   Shuttle Load Handler equipped truck. If the
                                                   voltage fluctuates erratically or intermittently,
                                                   refer to the VR6 checks for a Fork Load Handler
                                                   equipped truck. For a Shuttle Load Handler
                                                   equipped truck, perform the adjustment
                                                   procedure for the shuttle proximity switches on
                                                   page 7-178.
                                               Troubleshoot the Proximity Switches using the
                                               Schematics and the Shuttle Load Handler and
                                               Proximity Switch Operation information beginning on
                                               page 8-52.


Publication PDMM-0092, Issued: 30 September 2004                                                  5-49

--- Page 17 ---
The Raymond ® Transtacker Maintenance Manual                                   Section 5. Troubleshooting

                                                                                           Symptom Tables

         Possible Cause                    Action

         No Lift or Lower – Fuse FU15        1. Place the Main AC Disconnect Switch (S26) in the OFF
         Open                                   (down) position. Remove fuse FU15 from the truck and
                                                test it for continuity. Replace the fuse if there is no
                                                continuity.
                                             2. If the fuse tests good, check the wiring and connections
                                                from FU15-2 to the PC2 contactor, Circuit Breaker (CB1)
                                                and the Line Reactor (LR) to the L3 terminal on the VFI.
                                             3. Manually close the PC2 contactor tips. Check for
                                                continuity between FU15-2 and the L3 terminal on the
                                                VFI. Repair or replace components as necessary.

         Hoist Brake Not Released — No       1. Use the Schematics in the Appendix to determine if +24
         Fault Code 1                           VDC is being applied across the Hoist Brake Contactor
                                                Coil (BC).
                                             2. If the voltage is not present, check the associated wiring
                                                for continuity, shorts, or physical damage.

View the complete manual on HeyDownloads →