PDF Diagnostic Manual Kubota ECM System WG2503-E3 - 953 KB

This diagnostic manual is a must-have for any technician working on the Kubota WG2503-E3 engine's Electronic Control Module (ECM) system.

It provides detailed troubleshooting flowcharts, diagnostic trouble codes (DTCs), and testing procedures.

This guide helps you to quickly identify and resolve complex engine management issues.

PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
WAWhatsApp fFacebook 𝕏X TGTelegram βœ‰Email
PDF viewer loading area

Text Preview from This Manual

The text below was extracted from the visible preview pages to help you confirm the manual contents before download.

--- Page 1 ---
DIAGNOSIS MANUAL
 ECM SYSTEM


WG2503-E3


                    KiSC issued 08, 2016 A

--- Page 3 ---
WG2503-E3, DM                        ECM SYSTEM

1. OUTLINE
[1] OVERALL DIAGONOSTIC PROCEDURE


                        1-1
                                    KiSC issued 08, 2016 A

--- Page 4 ---
WG2503-E3, DM                                                                                                           ECM SYSTEM

                                                                                     No Start
              Checks                                                                  Action
 DEFINITION: The engine cranks OK but does not start.
 Preliminary Checks                    β€’ Refer to Important Preliminary Checks.
                                       β€’ Check the battery cranking voltage, voltage should not be less then 9.0 VDC.
                                       β€’ Check the inline fuse in the ECM battery power circuit. Refer to Engine Controls Schematics.
 Control Module Checks
                                       β€’ Check battery power, ignition power and ground circuits to the ECM. Refer to Engine Control
                                         Schematics. Verify voltage and/or continuity for each circuit.
                                       β€’ Check the TMAP sensor.
 Sensor Checks                         β€’ Check the Camshaft position (CMP) and Crankshaft (CKP) position sensors.
                                       β€’ Check the Gasoline pressure sensor.
                                       β€’   Check for fuel pump electrical circuit.
                                       β€’   Verify proper fuel pump pressure.
 Fuel System Checks                    β€’   Verify proper Fuel rail pressure.
                                       β€’   Refer to the Gasoline Fuel System Diagnosis.
                                       β€’   Check Electrical connections at the injectors.
                                       β€’ Check for the proper primary side ignition voltage output.
                                       β€’ Verify that the spark plugs are correct.
                                       β€’ Check the spark plugs for the following conditions:
                                         – Wet plugs
                                         – Cracks
 Ignition System Checks
                                         – Wear
                                         – Improper gap
                                         – Burned electrodes
                                         – Heavy deposits
                                       β€’ Check for loose ignition coil connections at the coil.
                                       β€’ Check for the following:
                                         – Vacuum leaks
                                         – Improper valve timing
                                         – Low compression
 Engine Mechanical Checks
                                         – Bent pushrods
                                         – Worn rocker arms
                                         – Broken or weak valve springs
                                         – Worn camshaft lobes
                                       β€’ Check the exhaust system for a possible restriction:
                                         – Inspect the exhaust system for damaged or collapsed pipes.
 Exhaust System Checks
                                         – Inspect the muffler for signs of heat distress, or for possible internal failure.
                                       β€’ Check for possible plugged catalytic converter. Refer to Restricted Exhaust System Diagnosis.


                                                                  1-11
                                                                                                                       KiSC issued 08, 2016 A

--- Page 5 ---
WG2503-E3, DM                                                                                                               ECM SYSTEM

                                                                                      Hard Start
               Checks                                                                   Action
 DEFINITION: The engine cranks OK, but does not start for a long time. The engine does eventually run, or may start, but immediately dies.
                                         β€’   Refer to Important Preliminary Checks.
                                         β€’   Make sure the vehicle’s operator is using the correct starting procedure.
 Preliminary Checks
                                         β€’   Be sure that there is fuel in the fuel tank.
                                         β€’   Check to make sure the manual tank valve is fully open.
                                         β€’ Check the Crankshaft Position (CKP) sensor.
 Sensor Checks
                                         β€’ Check the Camshaft sensor.

                                             IMPORTANT
                                         β€’    A closed LPG / Natural Gas manual fuel shut off valve will create an extended crank, OR no
                                              start condition.
                                         β€’   Verify the excess flow valve, in the LPG / Natural Gas manual shut-off valve, is not tripped.
 Fuel System Checks
                                         β€’   Check mixer module assembly, for proper installation and leakage.
                                         β€’   Verify proper operation, of the low pressure lock-off solenoids.
                                         β€’   Check for air intake system leakage, between the mixer and the throttle body.
                                         β€’   Check the fuel system pressures. Refer to the Fuel System Diagnosis.

                                             NOTE
                                         β€’    LPG / Natural Gas, being a gaseous fuel, requires higher, secondary ignition system
                                              voltages, for the equivalent gasoline operating conditions.
                                         β€’   Check for the proper ignition voltage output
                                         β€’   Verify that the spark plugs are correct, for use with LPG / Natural Gas.
                                         β€’   Check the spark plugs, for the following conditions:
                                             – Wet plugs
                                             – Cracks
 Ignition System Checks
                                             – Wear
                                             – Improper gap
                                             – Burned electrodes
                                             – Heavy deposits
                                         β€’   Check for loose ignition coil connections.
                                             IMPORTANT
                                        1.    If the engine starts, but then immediately stalls, check Crankshaft Position (CKP).
                                        2.    Check for improper gap, debris, or faulty connections.

                                           IMPORTANT
                                         β€’  The LPG / Natural Gas Fuel system, works on a fumigation principle of fuel introduction,
                                            and is more sensitive to intake manifold leakage, than the gasoline fuel supply system.
                                         β€’ Check for the following:
                                           – Vacuum leaks
                                           – Improper valve timing
 Engine Mechanical Checks
                                           – Low compression
                                           – Bent pushrods
                                           – Worn rocker arms
                                           – Broken or weak valve springs
                                           – Worn camshaft lobes. Refer to Workshop Manual
                                         β€’ Check the intake and exhaust manifolds, for casting flash.
                                         β€’   Check the exhaust system for a possible restriction:
                                         β€’   Inspect the exhaust system, for damaged or collapsed pipes.
 Exhaust System Checks
                                         β€’   Inspect the muffler, for signs of heat distress, or for possible internal failure.
                                         β€’   Check for possible, plugged, catalytic converter. Refer to Restricted Exhaust System Diagnosis.
 Additional Checks


                                                                     1-21
                                                                                                                           KiSC issued 08, 2016 A

--- Page 6 ---
WG2503-E3, DM                                                                                                           ECM SYSTEM
Diagnostic Calibration Configuration and Corrective
Actions
    Each fault within the GCP is capable of being                      Table 2 identifies the configuration options and
uniquely configured in the engine’s diagnostic calibration         corrective actions available for configuration of each
to cause one or more corrective actions while a given              fault. The desired action is set by KUBOTA.
fault is active.
Table 2: Diagnostic Corrective Actions
                Corrective Action                                                  Description
 Enable                                  Enables the fault for fault detection.
 Shutdown                                Cause an engine shutdown when fault becomes active.
                                         Retain fault as historic/previously active until cleared by a technician and does not allow
 Never Forget
                                         historic fault to be "auto-cleared".
 Turn on MIL                             Turn on MIL output when fault becomes active.
 CL Disable                              Disable closed-loop while the fault is active.
 CL Disable Key-Cyc                      Disable closed-loop while the fault is active and for the remainder of the key cycle.
 AL Disable                              Disable adaptive learn while the fault is active.
 AL Disable Key-Cyc                      Disable adaptive learn while the fault is active and for the remainder of the key cycle.
                                         Limit TPS to the Power Derate 1 % set in the diagnostic calibration while the fault is active.
 Power Derate 1                          The Power Derate 1 TPS % should be set higher than Power Derate 2 as Power Derate 2
                                         adds a higher level of protection.
                                         Limit TPS to the Power Derate 2 % set in the diagnostic calibration while the fault is active. If
                                         the calibration is set to "Latched for Key-Cycle" Power Derate 2 remains active until engine
 Power Derate 2
                                         speed and FPP conditions are satisfied. The Power Derate 2 TPS % should be set lower than
                                         Power Derate 1 as Power Derate 2 adds a higher level of protection.
                                         Limit RPM to the Low Rev Limit speed set in the diagnostic calibration while the fault is active.
 Low Rev Limit                           If the calibration is set to "Latched for Key-Cycle" Low Rev Limit remains active until engine
                                         speed and FPP conditions are satisfied.
                                         Limit RPM to the Forced Idle speed set in the diagnostic calibration while the fault is active
 Forced Idle
                                         and for the remainder of the key cycle.
 Soft Warning                            Turn on the soft warning output when the fault becomes active.
 Hard Warning                            Turn on the hard warning output when the fault becomes active.
                                         Run fault detection/checking while the engine is in a key-on, engine-off condition.
 Stopped Check                                NOTE
                                          β€’   It is recommended that this feature only be used for general sensor faults (high/low
                                              voltage) and some output drivers.


                                                              1-31
                                                                                                                       KiSC issued 08, 2016 A

--- Page 7 ---
WG2503-E3, DM                                           ECM SYSTEM
(Continued)
States (CL Test State)
1) Inactive
2) Pre-cat init test
3) Pre-cat heater test
4) Pre-cat power test
5) Pre-cat voltage test
6) Pre-cat BM test
7) Post-cat heater test
8) Post-cat power test
9) Post-cat rich test
10) Post-cat lean test
11) Finished
12) Invalid
Pre-Catalyst Monitored Status (CL Pre-Cat Test
Status)
1) Test Not Started
2) Test Running
3) Test Finished: Passed
4) Pre-cat EGO Lazy (generates appropriate EGO
    Lazy fault)
5) Pre-cat EGO Power Low
6) Pre-cat EGO non-responsive
7) Pre-cat EGO fueling error
8) Cannot start test (FPP or TCP % above limit is
    detected)
Post-Catalyst Monitored Status (CL Post-Cat Test
Status)
1) Test Not Started
2) Test Running
3) Test Finished: Passed
4) Post-cat EGO Lazy (generates appropriate EGO
    Lazy fault)
5) Post-cat EGO Power Low
6) Post-cat EGO Rich Failure
7) Post-cat EGO Lean Failure
8) Cannot start test (FPP or TCP % above limit is
    detected)


                                                1-41
                                                       KiSC issued 08, 2016 A

--- Page 8 ---
WG2503-E3, DM                                                                                           ECM SYSTEM
ELECTRONIC THROTTLE BODY (ETB) (ALL)                          THREE WAY CATALYST (ALL)
    The Kubota fuel systems utilize Drive By Wire                 The emission certified engine has been designed
(DBW), to control engine speed, in this type of               and calibrated, to meet the emission standards in effect
application. There is no direct connection between the        for 2010. To help meet the emission requirements, the
operator pedal, and the throttle shaft. Speed and load        vehicle has been attached with a Three Way Catalyst
control are determined by the ECM. Defaults                   (TWC). Kubota has designed and supplied the catalyst
programmed into the ECM software, and throttle position       in a separate unit. The catalyst function is the final
sensors, allow the ECM, to maintain safe operating            treatment, of the exhaust gases, which are created from
control, over the engine.                                     the combustion process. The three-way catalyst consists
    In a drive by wire application, the Electronic Throttle   of a honeycomb, coated with a mixture of platinum,
Body (ETB) (1) device, or "throttle body assembly", is        palladium, and rhodium. As the hot gases flow through
connected to the intake manifold of the engine. The           the catalyst section, an oxidation and reduction reactions
electronic throttle control device, utilizes an electric      takes place. This chemical reaction reduces the amount
motor, connected to the throttle shaft. In addition, a Foot   of CO, HC and NOx, in the engines exhaust. The
Pedal Position sensor (FPP) is located in the operator’s      Exhaust gas then flows through the outlet.
compartment. When the engine is running, electrical
signals are sent from the foot pedal position sensor, to
the engine ECM, when the operator depresses or
release the foot pedal. The ECM then sends an electrical
signal to the motor, on the electronic throttle control, to
increase or decrease the angle of the throttle blade, thus
increasing or decreasing the air flow to the engine.
    The electronic throttle control device also
incorporates two internal Throttle Position Sensors
(TPS), which provide output signals to the ECM, as to
the location of the throttle shaft and blade. The TPS
information is used by the ECM, to correct for speed and
load control, as well as emission control, and engine
protection.
    The ETB (1) utilized on USA emission certified
engines do not require any periodic adjustment.


(1) Electronic Throttle Body (ETB)
(2) Spacer
(3) O-Ring


                                                          1-51
                                                                                                       KiSC issued 08, 2016 A

--- Page 9 ---
WG2503-E3, DM                                                                                      ECM SYSTEM
JOINT POINTS (A, B, C, D)
 β€’ A: The points below are jointed.
   IGNITION_FUSE (15A)
   ALTERNATOR_PIN_2
   VIC2_PIN_S
   COIL_CYL_#1,2,3,4_PIN_1
   INJ_CYL_#1,2,3,4_PIN_2
   O2_SENSOR_PRE_CATALYST_PIN_C
   O2_SENSOR_POST_CATALYST_PIN_C
 β€’ B: The points below are jointed.
   BATTERY +
   KEY_SWITCH_PIN_OFF
   ALTERNATOR_CHARGE_INDICATION_LAMP
   FUEL_SEL_PIN_NG
   MIL_LAMP
 β€’ C: The points below are jointed.
   ECM_PIN_19 (5 V_EXT1)
   THROTTLE_ACTUATOR_PIN_3
   TMAP (BOOST) PIN_B
   FPM_PIN_C
   VIC1_PIN_M
 β€’ D: The points below are jointed.
   ECM_PIN_20 (5 V_RTN1)
   COOLANT_TEMPERATURE_SENSOR_PIN_1
   O2_SENSOR_PRE_CATALYST_PIN_A
   O2_SENSOR_POST_CATALYST_PIN_A
   THROTTLE_ACTUATOR_PIN_2
   TMAP (BOOST)_PIN_C
   FPM_PIN_A
   VIC1_PIN_L
(1)   FPM                        (10) KEY ST                (18) FUEL_PUMP 15A FUSE   (26) ENG. BODY
(2)   FPM Intermediate Harness   (11) KEY IG                (19) STARTER 15A FUSE     (27) VIC2 Connector
(3)   VIC1 Connector             (12) Charge Indication     (20) Starter Relay        (28) SPEED_METER
(4)   ACCEL SENSOR1              (13) ECM 10A FUSE          (21) STARTER              (29) GOV_SEL2
(5)   ACCEL SENSOR2              (14) Power Relay           (22) 60A FUSE             (30) GOV_SEL1
(6)   MIL                        (15) IGNITION 15A FUSE     (23) ALTERNATOR           (31) ECM (1/2)
(7)   CAN for Vehicle            (16) VSW 5A FUSE           (24) BATTERY              (a) to ECM_PIN_14 (CAN1 +)
(8)   FEED_PUMP                  (17) Fuel_pump Relay       (25) BODY EARTH           (b) to ECM_PIN_15 (CAN1 ο€­)
(9)   KEY OFF


                                                          1-61
                                                                                                  KiSC issued 08, 2016 A

--- Page 10 ---
WG2503-E3, DM                                                                                    ECM SYSTEM
JOINT POINTS (A, B, C, D)
 β€’ A: The points below are jointed.
   IGNITION_FUSE (15A)
   ALTERNATOR_PIN_2
   VIC2_PIN_S
   COIL_CYL_#1,2,3,4_PIN_1
   INJ_CYL_#1,2,3,4_PIN_2
   O2_SENSOR_PRE_CATALYST_PIN_C
   O2_SENSOR_POST_CATALYST_PIN_C
 β€’ B: The points below are jointed.
   BATTERY +
   KEY_SWITCH_PIN_OFF
   ALTERNATOR_CHARGE_INDICATION_LAMP
   FUEL_SEL_PIN_NG
   MIL_LAMP
 β€’ C: The points below are jointed.
   ECM_PIN_19 (5 V_EXT1)
   THROTTLE_ACTUATOR_PIN_3
   TMAP (BOOST) PIN_B
   FPM_PIN_C
   VIC1_PIN_M
 β€’ D: The points below are jointed.
   ECM_PIN_20 (5 V_RTN1)
   COOLANT_TEMPERATURE_SENSOR_PIN_1
   O2_SENSOR_PRE_CATALYST_PIN_A
   O2_SENSOR_POST_CATALYST_PIN_A
   THROTTLE_ACTUATOR_PIN_2
   TMAP (BOOST)_PIN_C
   FPM_PIN_A
   VIC1_PIN_L
   NOTE
 β€’ The picture shows the pin arrangement of the connector housing viewed from the harness connector
   mating side.
(1)   ECM (2/2)          (8) INJ_SYL_#3          (15) Throttle Actuator           (22) Oil SW
(2)   COIL_CYL_#1        (9) INJ_SYL_#4          (16) O2 sensor Pre Catalyst      (23) Coolant temperature sensor
(3)   COIL_CYL_#2        (10) Knock sensor       (17) O2 sensor Post Catalyst     (a) to VSW_FUSE (5A)
(4)   COIL_CYL_#3        (11) Crank sensor       (18) Can termination Connector   (b) to DEPR_FUSE (5A)
(5)   COIL_CYL_#4        (12) Cam sensor              Open: termination OFF       (c) to ECM_FUSE (10A)
(6)   INJ_SYL_#1         (13) TMAP (BOOST)            Close: termination ON       (d) to VIC1_PIN_N
(7)   INJ_SYL_#2         (14) Lockoff Valve      (19) DEPR                        (e) to VIC1_PIN_P
                                                 (20) DIAG_TOOL Connector
                                                 (21) CAN Tool


                                               1-71
                                                                                                KiSC issued 08, 2016 A

--- Page 11 ---
WG2503-E3, DM                                                                    ECM SYSTEM
Connector Number: C016*1
Name: DEPR Connector


          Pin Number                   Description               Wire Color
                1                    CAN Termination              WHITE
                2                       CAN 1 +                DK_BLUE/PINK
                3                       VRELAY                PINK/DK_GREEN
                4                        Ground                   BLACK
                5                        CAN ο€­                DK_BLUE/WHITE
                6                      VBAT (12 V)               RED/TAN


Connector Number: C017*1
Name: Bosch Throttle Connector


          Pin Number                   Description               Wire Color
                1                        DBW ο€­                  TAN/ORANGE
                2                      5 V_RTN 1              BLACK/LT_GREEN
                3                      5 V_EXT 1               LT_GREEN/RED
                4                        DBW +                  PINK/WHITE
                5                        TPS 2                LT_BLUE/DK_BLUE
                6                        TPS 1                PURPLE/LT_BLUE


   NOTE
 β€’ *1: All connector views are the mating connector view.


                                                       1-81
                                                                                KiSC issued 08, 2016 A

--- Page 12 ---
WG2503-E3, DM                                                                                              ECM SYSTEM
LPG / NATURAL GAS PRESSURE REGULATORS                          GASOLINE FUEL PRESSURE MANIFOLD
LPG / NATURAL GAS DUAL STAGE REGULATOR                             On Bi-fuel and dedicated gasoline engines, fuel is
(DSR)                                                          delivered to the gasoline injector rails via an electric fuel
    The EControls LPG / Natural Gas DSR is a two stage         pump. The ECM controls fuel delivery pressure via a
mechanical regulator with an integral vaporizer which          PWM low side drive circuit connected to the ground
reduces the fuel inlet or tank pressure to a specific lower    terminal of the pump. The ECM increases or decreases
pressure and adds heat to the fuel for vaporization. You       the fuel pump’s voltage to achieve the desired pressure
should check the following items at a minimum of once          using pressure feedback information from the gasoline
per year:                                                      fuel pressure manifold assembly. This manifold
 β€’ Check for any fuel leaks at the inlet and outlet            assembly also measures the gasoline fuel temperature
    fittings.                                                  and provides this information to the ECM. This manifold,
 β€’ Check for any fuel leaks at the connecting seams of         along with the electric fuel pump, will be located on the
    the regulator body.                                        chassis. By closely maintaining the target fuel pressure
 β€’ Check the inlet and outlet coolant fittings at the          using minimum pump current flow, a minimal amount of
    regulator body.                                            fuel is returned to the tank. The fuel pressure manifold
 β€’ Check the inlet and outlet coolant lines for                and fuel pump do not require adjustment. The following
    hardening, cracking, chaffing or splits. If any of these   items must be inspected once per year.
    conditions exist replace the coolant lines.                  β€’ Check the mounting bracket for the fuel pressure
 β€’ Check the inlet and outlet coolant line hose clamps             manifold and fuel pump, for cracks or breakage.
    at each connection, tighten if necessary.                    β€’ Check the securing method for the fuel pressure
 β€’ Check the mounting bracket to insure the regulator is           manifold and fuel pump to insure the devices are
    securely mounted, tighten if necessary.                        firmly attached.
 β€’ Check any of the rubber isolators used for mounting           β€’ Check the electrical connection at both the fuel
    for cracking, hardening or separation.                         pressure manifold and fuel pump.
 β€’ Check the regulator for a buildup of oil in the second
    stage chamber of the regulator. Drain the oil by           INJECTOR RAIL AND INJECTORS
    opening the drain plug located at the bottom of the            The injector rail and injectors require no periodic
    secondary chamber.                                         adjustment. You should annually inspect the following
    NOTE                                                       items on the fuel rails and injectors.
 β€’ Certain Kubota LPG / Natural Gas systems may                  β€’ Check to make sure the rail bracket is securely
    be fitted with a Direct Electronic Pressure                    attached to the engine.
    Regulator (DEPR) which is downstream of the                  β€’ Check to make sure the rail brackets have no
    DSR. Check these items when inspecting the                     cracking or breaking.
    DEPR:                                                        β€’ Check to make sure that each injector is securely
 β€’ Check the harness connection on the electronic                  attached to the rail bracket.
    control section, to insure it is seated and locked.          β€’ Check each injector electrical connection to insure
 β€’ Check to make sure the DEPR assembly is securely                the connector is securely attached.
    mounted.                                                     β€’ Leak check all the connections on the manifold at
    NOTE                                                           each injector connector, and the inlet and outlet
 β€’ All EControls LPG / Natural Gas systems are                     fitting at the rail, using an electronic leak detector or
    fitted with an LPG / Natural Gas Fuel Lock Off                 a soapy solution.
    device which is typically mounted to the inlet of            β€’ Check the injector delivery hose (if used) for any
    the DSR. These are the additional items when                   cracking, kinky, cuts, or deformation, and replace if
    inspecting the regulator:                                      necessary.
 β€’ Check for any fuel leaks at the inlet and outlet
    fittings.                                                  ELECTRICAL SYSTEM CHECKS
 β€’ Check the Lock Off electrical connector, to insure it          The electrical system, sensors, wiring harness, and
    is seated and locked.                                      ECM do not require any periodic adjustments. You
 β€’ Check to insure the solenoid retaining nut is               should annually inspect the following items.
    tightened and fully seated.


                                                           1-91
                                                                                                          KiSC issued 08, 2016 A

--- Page 14 ---
WG2503-E3, DM                                                                                             ECM SYSTEM

(1) Restricted Exhaust System Diagnosis
Exhaust System Description                                    Check at Heated Exhaust Gas Oxygen Sensor
     The emission certified engine has been designed          (HEGO)
and calibrated to meet the emission standards in effect       1. Carefully remove the HEGO.
for 2010. To help meet the emission requirements the          2. Install exhaust back pressure gage in place of the
vehicle has been attached with a three way catalyst. The         HEGO. (Refer to below figure.)
catalyst is a three way catalyst, sound damping and           3. With the engine idling at normal operating
spark arresting unit. Besides controlling the noise              temperature, observe the exhaust system back
created from the combustion process, and preventing              pressure reading on the gage. Reading should not
sparks from escaping from the exhaust system the most            exceed 8.6 kPa (0.088 kgf/cm2, 1.2 psi).
important function is treating the exhaust gases which        4. Increase engine speed to 2000 min-1(rpm) and
are created from the combustion process. The three-way           observe gage. Reading should not exceed 20.7 kPa
catalyst consists of a honeycomb core coated with a              (0.211 kgf/cm2, 3.00 psi).
mixture of precious metals. The hot gases flow through        5. If the back pressure at either speed exceeds
the catalyst honeycomb core where an oxidation and               specification, a restricted exhaust system is
reduction reactions take place. These chemical                   indicated.
reactions reduce the amount of CO, HC and NOX in the          6. Inspect the entire exhaust system for a collapsed
engines exhaust. The Exhaust gas then flows through              pipe, heat distress or possible internal muffler failure.
the tailpipe outlet.                                          7. If there are no obvious reasons for the excessive
     During normal operation the exhaust system could            back pressure, the catalytic converter is suspected
become damaged. Damage which reduces the flow of                 to be restricted and should be replaced using the
the exhaust gas will create increased back pressure in           recommended procedures.
the engine. Reduction in exhaust flow can result from
crushed muffler outlets or melted catalyst brick inside the
converter.
     It may be necessary to measure the back pressure
in the exhaust system. To determine if the back pressure
in the engine is correct use the following procedure.

Diagnostic Aids
Tools Required:
 β€’ Back pressure gage 0 to 69 kPa (0 to 0.70 kgf/cm2,
   0 to 10 psi)
Diagnostic Scan Tool:
 β€’ EControls GCP Display SW Tool

                                                              (1) Back Pressure Gage        (3) Exhaust Manifold
                                                              (2) Oxygen Sensor (O2S)


                                                         1-101
                                                                                                        KiSC issued 08, 2016 A

--- Page 15 ---
WG2503-E3, DM                                                                                                           ECM SYSTEM

       DTC                        606                                 627                                         628
                                                                                                Fuel Pump Relay      Fuel Pump Motor
 Name            Internal Processor Diagnostics     Fuel Pump Relay Control/Coil
                                                                                                Control/Coil         Feedback
 DTC Name        Microprocessor Failure-COP         Fuel Pump Relay Coil Open                   Fuel Pump Relay Ground Short
          SPN                     629                                1348                             1348                   1347
 J1939
          FMI                     31                                   5                                4                      5
 MIL                              ON                                  ON                               ON                     ON
                  β€’ Faulty ECU                       β€’ Open coil in relay                        β€’ Relay pull in
                                                     β€’ Open in relay driver circuit in engine      coil shorted
                                                       harness                                     internally
 Detected Item                                                                                   β€’ relay driver
                                                                                                   circuit shorted
                                                                                                   to ground in
                                                                                                   wire harness
 DTC Set          β€’ Key on                           β€’ Key On, Engine Off                        β€’ Engine Running
 Preconditions
                  β€’ Internal microprocessor error    β€’ Fuel Pump relay coil output open          β€’ Fuel Pump            β€’ Fuel pump
                                                       circuit                                     relay coil             motor
                                                                                                   output                 high-side
 DTC Set                                                                                           shorted to             on-state < 4.0
 Conditions                                                                                        ground                 volts
                                                                                                                        β€’ Battery
                                                                                                                          voltage > 8.0
                                                                                                                          volts
 Period for       β€’ N/A                              β€’ 10 samples                               β€’ 10 samples            β€’ 2 sec
 Judgment or
 Number of
 Occurrence
 for Judgment
                  β€’ Never Forget                     β€’ None                                      β€’ None                 β€’ None
 System
                  β€’ AL Disable KC
 Action
                  β€’ Power derate 2
 Engine
                 OFF                                ON                                          ON                   ON
 Warning Light


                                                           1-111
                                                                                                                     KiSC issued 08, 2016 A

--- Page 16 ---

View the complete manual on HeyDownloads β†’