PDF Assembly & Operating Manual Frontier DH4218 DH4221 Disk Harrow - 1 MB
This manual provides both assembly and operating instructions for the Frontier DH4218 and DH4221 Wheel Off Set Disk Harrows.
It guides you through the initial setup process and provides important information on proper operation and adjustments in the field.
Following these instructions is key to achieving optimal performance and ensuring the long-term durability of your tillage equipment.
PDF Viewer
Viewer loads when you scroll here
SHARE THIS MANUAL
Download the PDF Manual
PDF viewer loading area
Text Preview from This Manual
The text below was extracted from the visible preview pages to help you confirm the manual contents before download.
--- Page 1 ---
ASSEMBLY & OPERATING INSTRUCTIONS
MODELS DH4218 AND DH4221
HINGE-WHEEL OFFSET DISK HARROW
FORM NO.: 5RPMAN332AO
PUBLISHED: 06-08
Printed in USA
--- Page 3 ---
Checklists
PREDELIVERY CHECK LIST
After the disk harrow has been completely
Check all pins to make sure retaining
assembled and lubricated, inspect it to be sure it
hardware is in place.
is in proper operating condition before making
delivery to the customer. The following check list
Paint all unpainted bolts and nuts and
is a reminder of points to inspect. Check off each
any other parts scratched in shipment.
item as it is found satisfactory.
Connect disk harrow securely to tractor
The disk harrow has been assembled
drawbar and check hydraulic system for
according to instructions. Nuts on all bolts
leaks and proper operation of the
have been tightened.
hydraulic components.
The axle lift fittings have been installed
Safety chain is attached.
and lubricated.
This disk harrow has been checked and,
Be sure all grease fittings are installed.
to the best of my knowledge, is ready for
Lubricate the harrow.
delivery to the customer.
Tires are properly inflated.
Check to insure that the Warranty
Registration, located on the Frontier
Disk gangs rotate freely without dragging
dealer website, has been submitted by
on scrapers.
the Dealer.
(Date Set Up):
(Signature of
Set Up Person):
11
--- Page 4 ---
Safety
USE SAFETY LIGHTS AND DEVICES
Prevent collisions between other road users,
slow moving tractors with attachments or towed
equipment, and self-propelled machines on
public roads. Frequently check for traffic from the
rear, especially in turns, and use hand signals or
turn signal lights.
Use headlights, flashing warning lights, and turn
signals day and night. Follow local regulations
for equipment lighting and marking. Keep the
lighting and marking visible and in good working
order. Replace or repair lighting and marking that
has been damaged or lost.
USE A SAFETY CHAIN
A safety chain will help control drawn equipment
should it accidentally separate from the drawbar.
Using the appropriate adapter parts, attach the
chain to the tractor drawbar support or other
specified anchor location. Provide only enough
slack in the chain to permit turning.
See your Frontier dealer for a chain with a
strength rating equal to or greater than the gross
weight of the towed machine. Do not use safety
chain for towing.
21
--- Page 5 ---
Attaching and Detaching
ATTACHING HYDRAULIC HOSES
CAUTION: Shut off tractor engine,
work levers back and forth to relieve
system of pressure.
CAUTION: Escaping fluid under
pressure can penetrate the skin
causing serious injury. Avoid the
hazard by relieving pressure before
disconnecting hydraulic or other
lines. Tighten all the connections
before applying pressure. Search for
leaks with a piece of cardboard.
Protect hands and body from high-
pressure fluids.
If an accident occurs, see a doctor
immediately. Any fluid injected into
the skin must be surgically removed
within a few hours or gangrene may
result. Doctors unfamiliar with this
type of injury should reference a
knowledgeable medical source.
1. Plug hydraulic cylinder hoses into No.1
tractor hydraulic coupler.
ATTACHING WARNING LIGHT PLUG
Attach warning light plug to 7-terminal plug on
tractor.
31
--- Page 6 ---
Operating the Machine
OFFSET BAR HEIGHT ADJUSTMENT
On each of the front gang carrier hitch plates,
there are located three adjustment holes that are
used to adjust the height of the offset bar. This
should be adjusted in order to make the drawbar
on the disk as close to level as possible with the
tractor drawbar when the disk is in the ground in
the plowing position.
If the tractor drawbar is higher than the disk
drawbar, there is a tendency to pull the front disk
gang out of the ground. On the other hand, if the
tractor drawbar is lower, it will tend to pull the
front gang deeper into the ground.
Therefore, the harrow will plow most level with
the front and rear gang, if the drawbar on the
disk is level with the drawbar on the tractor.
POSITIONING THE DRAWBAR ANGLE
SELECTING BOLT
This important adjustment increases or
decreases the angle of the front and rear gang
and allows you to achieve a balance between
the two. If the front gang angle is increased, the
rear gang angle will be decreased and if the front
angle is decreased the rear angle will be
increased.
The greater the angle, the more aggressive the
gang will plow.
Too much angle will cause the gang to bulldoze
and the soil will not flow through the disk blades.
The ideal situation is for both the front and rear
gangs to have close to equal amounts of angle
so they plow to the same depth.
41
--- Page 7 ---
Maintenance
MAINTENANCE
CAUTION: SAFETY GUIDELINES
BEFORE SERVICING THE HARROW, ALWAYS:
1. Lower the harrow to the ground.
2. Shut the tractor off.
3. Lock the tractor’s parking brake.
4. Remove the key.
INADVERTENT OR UNINTENTIONAL MOVEMENT OF THE HARROW WHILE WORKING
AROUND THE DISK GANGS COULD RESULT IN SERIOUS PERSONAL INJURY.
NEVER WORK UNDER A RAISED HARROW.
The raised harrow could fall suddenly causing serious personal injury. Always lower the
harrow to the ground before servicing. Never rely on the hydraulic system to hold the
harrow up.
PERIODICALLY, VISUALLY INSPECT THE HARROW.
Look for hydraulic leaks, and broken, missing or malfunctioning parts and make any
necessary repairs.
USE CAUTION WHEN INFLATING TIRES.
Use a clip-on air chuck, extension hose with gauge, and stand to one side away from the tire
when inflating to avoid the possibility of personal injury due to blow offs, etc. Maintain proper
air pressure in the tires.
Important! Never exceed manufacturer’s maximum psi. Displayed on the sidewall of the tire.
BEFORE DISCONNECTING ANY HYDRAULIC LINE RELIEVE THE PRESSURE.
Escaping hydraulic oil under pressure can have sufficient force to penetrate the skin causing
serious personal injury. If injured by escaping hydraulic fluid, obtain medical treatment
immediately
HANDLE THE GANG ASSEMBLIES WITH CARE.
The disk blades are sharp and could cut hands, feet, etc. Use chock blocks to prevent the
gang assembly from rolling on surfaces before assembly to the frame. Wear gloves when
handling the disk blades or gang assemblies.
PURGE AIR FROM THE HYDRAULIC SYSTEM BEFORE OPERATION.
Always be sure the hydraulic lines and cylinders are free of air and do not leak. After
connecting the hydraulic lines, carefully cycle the hydraulic cylinders several times to purge
air from the hydraulic system. Visually check all connections for leaks before cycling the
hydraulic cylinders.
51
--- Page 8 ---
Assembly
CAUTION: SAFETY GUIDELINES
WEAR PROPER ATTIRE WHEN ASSEMBLING HARROW.
Always wear relatively tight and belted clothing to avoid entanglement in equipment.
Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands,
hearing and head.
HANDLE THE DISK GANG COMPONENTS WITH CARE DURING ASSEMBLY.
The disk blades are sharp and could cut hands, feet, etc. Wear gloves when handling
the disk blades or gang components.
Disk blades and gang components are heavy and can be awkward to handle during
assembly of the gang. Two-person gang assembly is recommended. Use overhead
lifting device or other supports if necessary to insure safe assembly of the disk gang.
HANDLE THE GANG ASSEMBLIES WITH CARE.
The disk blades are sharp and could cut hands, feet, etc. Use chock blocks to prevent
the gang assembly from rolling on surfaces before assembly to the frame. Wear
gloves when handling the disk blades or gang assemblies.
SUPPORT THE FRAME ASSEMBLY DURING ASSEMBLY.
Support the harrow frame with stands or lifting devices that are in good condition and
that are capable of handling the weight of the assembly. Be sure that the supports are
on a clean, dry surface.
PURGE AIR FROM THE HYDRAULIC SYSTEM BEFORE OPERATION.
After connecting the hydraulic lines, carefully cycle the hydraulic cylinders several
times to purge air from the hydraulic system. Visually check all connections for leaks
before cycling the hydraulic cylinders.
NEVER USE YOUR HANDS TO CHECK FOR HYDRAULIC LEAKS.
Escaping hydraulic oil under pressure can have sufficient force to penetrate the skin
causing serious personal injury. If injured by escaping hydraulic fluid, obtain medical
treatment immediately.
61
--- Page 9 ---
Assembly
HYDRAULIC GROUP ASSEMBLY INSTALLATION
For a detailed description and part numbers refer to the hydraulic group at the end of the
assembly steps.
Note: Always use a high quality, high-pressure hydraulic thread sealant on all pipe thread fittings to
prevent hydraulic leaks. Refer to the HYDRAULIC CONTROL GROUP ILLUSTRATION (previous page)
for locating the hydraulic components on the harrow. Refer to the hydraulic group assembly diagram and
parts listing found in this manual for part numbers and descriptions on individual components.
STEP A
Attach the 3” by 6” hydraulic cylinder base end to the frame leveler on the front gang carrier. Then attach
the rod end of the cylinder to the cylinder mounting bracket on the offset bar. Remove the shipping plugs
from the cylinder ports and install the cylinder fittings as shown on the HYDRAULIC CONTROL GROUP
ILLUSTRATION.
CAUTION: The 3” x 6” cylinder base end port uses two fittings to connect the hydraulic hose.
One of the two fittings is a restrictor fitting. The restrictor fitting allows the oil to move out of the
cylinder more slowly when the disk is being lowered to the ground from the raised position. If
the restrictor fitting is not placed in the base end port the front of the disk will fall rapidly when
the disk is being lowered from the raised position!
71